MIDEA MDRB424FGE02I (01) PDF Document

The main components of the MIDEA MDRB424FGE02I are:

1. Drawer (refrigerator)

2. Shelf

3. Drawer (freezer)

4. Door tray

The MIDEA MDRB424FGE02I refrigerator is designed to operate normally within the temperature range specified by its climate class. The climate class can be found on the rating plate and the product label. The product may not operate properly at temperatures outside of its specific range.

When installing your MIDEA MDRB424FGE02I refrigerator, allow over 100 mm of clearance from each adjacent wall. Too small of a distance from adjacent items may result in degraded freezing capability and increased electricity costs.

To reverse the door on your MIDEA MDRB424FGE02I, you will need a standard screwdriver, a Phillips screwdriver, a putty knife/thin-blade screwdriver, a 5/16″ socket and ratchet, and masking tape. It is recommended that someone assist you to avoid injury. Make sure the refrigerator is unplugged and empty. Keep all removed parts for reuse.

Step 1. Power off the refrigerator and remove all objects from the door trays.

Step 2. Dismantle the upper hinge cover, upper hinge, and the hole cap from the other side. Remove the refrigerating door.

Step 3. Dismantle the middle hinge, the screws, the screw hole caps, and remove the freezer door.

Step 4. Dismantle the bottom hinge, hole caps, and screws. Install the bottom hinge shaft and adjust the foot on the other side of the bottom hinge, then install the hinge on the other side.

Step 5. Dismantle the screw, sleeve pipe, and stopper from the refrigerating and freezer doors. Also, remove the support on the lower cover of the refrigerating door. Install them on the other side of the doors in order. Take the bottom stopper from the accessories package.

Step 6. Exchange the position of the sleeve pipe and hole cap at the top cover of the refrigerating door. Install the upper hinge sleeve on the freezer door to the hole on the other side of the axis sleeve.

Step 7. Place the refrigerating chamber door on the middle hinge and install the upper hinge and hinge cover.

Step 8. Place the refrigerating door on the middle hinge, then install the upper hinge, hinge cover, and hole cap.

Before using your MIDEA MDRB424FGE02I refrigerator, remove all packing materials, including bottom cushions, foam pads, and tapes from inside. Tear off the protective film on the doors and the refrigerator body.

Keep the refrigerator away from heat and direct sunlight. Do not place it in moist or watery places to prevent rust or reduction of insulating effect.

Do not spray or wash the refrigerator. Do not place it in moist places where it can be easily splashed with water, as this can affect its electrical insulation properties.

The refrigerator should be placed in a well-ventilated indoor area on flat, sturdy ground. If the ground is unstable, rotate the leveling wheel left or right to adjust.

To avoid vibration, your MIDEA MDRB424FGE02I must be level. Adjust the leveling screws to compensate for an uneven floor. The front should be slightly higher than the rear to aid in door closing. You can turn the leveling screws easily by tipping the cabinet slightly. Turn the leveling screws counterclockwise to raise the unit and clockwise to lower it.

Step 1. Remove all food from inside the appliance.

Step 2. Unplug the power cord and fix it into the power plug hook at the rear or on top of the appliance.

Step 3. Tape parts such as shelves and the door handle to prevent them from falling off while moving.

Step 4. Move the appliance carefully with more than two people. When transporting it over a long distance, keep the appliance upright.

Step 5. After installing the appliance, connect the power plug to a socket to switch it on.

Any replacement or maintenance of the LED lamps should be done by the manufacturer, its service agent, or a similar qualified person. This product contains a light source of energy efficiency class .

Step 1. Please unplug the refrigerator before removal.

Step 2. Remove the lampshade with a screwdriver.

Step 3. Take down the lamp panel.

Step 4. Remove the connection terminal.

The appliance should be located in the coolest area of the room, away from heat-producing appliances or heating ducts, and out of direct sunlight.

Let hot foods cool to room temperature before placing them in the appliance. Overloading forces the compressor to run longer.

Be sure to wrap foods properly and wipe containers dry before placing them in the appliance to cut down on frost build-up.

The storage bin should not be lined with aluminum foil, wax paper, or paper toweling, as liners interfere with cold air circulation.

Organize and label food to reduce door openings and extended searches. Remove as many items as needed at one time, and close the door as soon as possible.

When you power on the refrigerator, the display screen will shine for 3 seconds, and then it will run according to temperature setting 3.

Gear setting:

Press the SET key to change the temperature setting. The refrigerator will run under the new setting after 15 seconds. The cycle is Setting 1 → Setting 2 → Setting 3 → Setting 4 → Setting 5 → Setting 6 → Setting 1 and so on.

Fast cool mode:

This mode provides circulating modulation for rapid cooling. The rapid cooling indicator lights up, and the refrigerator operates at 2°C. The fast cool mode is automatically disabled after 24 hours. This function can also be used as a Super freezing function.

Adjustment of manual air damper knob:

Turn the air damper slider up to lower the temperature inside the freezer room. Turn the air damper slider down to raise the temperature inside the freezer room.

If a fault occurs, the corresponding LED lights will display a combined failure code. Although the refrigerator may still have cooling and freezing functions with these faults, you should contact a maintenance specialist to ensure normal use.

Refrigerating chamber:

Suitable for a variety of fruits, vegetables, beverages, and other food consumed in the short term. The suggested storage time is 3 to 5 days.

Cooking foods should not be put in the refrigerating chamber until cooled to room temperature.

Foods are recommended to be sealed before being placed in the refrigerator.

The glass shelves can be adjusted up or down for a reasonable amount of storage space.

Freezing chamber:

The low-temperature freezing chamber can keep food fresh for a long time and is mainly used to store frozen foods and make ice.

It is suitable for storing meat, fish, rice balls, and other foods not to be consumed in the short term.

Chunks of meat are preferably divided into small pieces for quick freezing and easy access. Food should be consumed within the shelf time.

Note: Storing too much food after the initial connection to power may adversely affect the freezing effect.

Please store different foods according to the compartments or target storage temperature of your purchased appliance.

Overall Cleaning (Please unplug the refrigerator for defrost and cleaning):

Dust behind the refrigerator and on the ground should be timely cleaned to improve cooling effect and energy saving.

Check the door gasket regularly for debris. Clean it with a soft cloth dampened with soapy water or diluted detergent.

The interior should be cleaned regularly to avoid odor. Turn off the power before cleaning, and remove all food, drinks, shelves, etc.

Use a soft cloth or sponge to clean the inside with two tablespoons of baking soda and a quart of warm water. Then rinse and wipe clean. Let it dry naturally before turning on the power.

For difficult-to-clean areas (narrow gaps, corners), wipe them regularly with a soft rag, soft brush, etc., and use auxiliary tools like thin sticks if necessary.

Do not use soap, detergent, scrub powder, or spray cleaner, as these may cause odors or contaminate food.

Clean the bottle frame, shelves, and drawers with a soft cloth dampened with soapy water or diluted detergent. Dry naturally.

Wipe the outer surface with a soft cloth dampened with soapy water, detergent, etc., and then wipe dry.

Do not use hard brushes, steel balls, wire brushes, abrasives, or organic solvents, as they may damage the fridge surface and interior.

Do not rinse directly with water during cleaning to avoid short circuits or affect electrical insulation.

Defrosting:

The refrigerator is made based on the air-cooling principle and has an automatic defrosting function. Frost formed due to a change of season or temperature may also be manually removed by disconnecting the appliance from the power supply or by wiping with a dry towel.

Cleaning of door tray:

Use both hands to squeeze the tray and push it upward to take it out. After washing, you can adjust its installing height according to your requirement.

Cleaning of glass shelf:

The innermost part of the refrigerator liner where the shelves contact has a backstop. Raise the shelves upward to take them out. Adjust or clean the shelves as needed.

Cleaning the vegetable drawer:

1. Remove the contents of the drawer. Hold the handle and pull it out completely until it stops.

2. Lift the vegetable drawer up and remove it by pulling it out.

Power failure:

In case of a power failure, even in summer, food inside the appliance can be kept for several hours. During the power failure, reduce the number of door openings and do not put more fresh food into the appliance.

Long-time non-use:

The appliance should be unplugged and then cleaned. The doors should be left open to prevent odor.

The OK-temperature indicator can be used to determine temperatures below +4°C. You should gradually reduce the temperature if the sign does not indicate “OK”.

Temperature indicator setting:

The indicator will monitor the average temperature in the coldest zone. WARNING: This indicator is intended to work only with your MIDEA MDRB424FGE02I refrigerator.

Checking the temperature in the coldest zone:

You can regularly check that the temperature of the coldest zone is correct. The internal temperature depends on factors like ambient room temperature, amount of food stored, and frequency of door opening.

When the indicator shows « OK », it means your thermostat is well adjusted and the internal temperature is correct.

If the indicator turns WHITE, the temperature is too high. In this case, increase the refrigerator temperature control setting and wait for 12 hours before a new visual inspection. When fresh food has been introduced or the door has been left open, it’s possible for the indicator to turn WHITE for a while.