FREE ENGLISH MICTRACK MT510 (01) PDF USER GUIDE
FREE ENGLISH MICTRACK MT510 (01) PDF USER MANUAL
FREE ENGLISH MICTRACK MT510 (01) PDF OWNER GUIDE
FREE ENGLISH MICTRACK MT510 (01) PDF OWNER MANUAL
FREE ENGLISH MICTRACK MT510 (01) PDF REFERENCE GUIDE
FREE ENGLISH MICTRACK MT510 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH MICTRACK MT510 (01) PDF REFERENCE MANUAL
FREE ENGLISH MICTRACK MT510 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH MICTRACK MT510 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD MICTRACK MT510 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the applications and features of the MT510 3G Personal Tracker?
The MT510 3G Personal Tracker supports WCDMA/UMTS and can locate and monitor remote targets by SMS/PC/APP. Its features include:
3G WCDMA/UMTS support
Real-time position inquire
Two way voice communication
Voice monitoring
Personal trip history on web
SOS alarm
Over-speed alarm
Motion report
Geo-fence alarm
Backup battery low power alarm
Power saving mode
Mileage report
What are the specifications of the MT510 3G Personal Tracker?
| Item | Specifications |
|---|---|
| Dimension | 89(L)*57(W)*20(H)mm |
| Weight | 89g |
| Charging Voltage | Micro USB interface DC 5V |
| Backup battery | 1600mAh/3.7V |
| Power consumption | 60mA standby current |
| 3G Frequency bands | MT510-E: 900/2100MHz@UMTS, 900/1800MHz@GSM |
| MT510-A: 850/1900MHz@UMTS, 850/900/1800/1900MHz@GSM | |
| MT510-T: 850/2100MHz@UMTS, 850/900/1800/1900MHz@GSM | |
| GPS Chip | U-BLOX7 |
| GPS Sensitivity | -162dBm |
| Channel | 56 Channel |
| Positioning Accuracy | 10m |
| Hot start | 1s on average |
| Warm start | 15s on average |
| Cold start | 30s on average |
| Working temperature | -20°C to 55°C |
| Humidity | 5%~95% non-concretion |
| Antenna | Built-in 3G/GPS antenna |
| Sensor | 3D acceleration sensor |
| LED | 3G/GPS/CHG |
| SIM Card interface | Standard SIM Card |
What does the MT510 3G Personal Tracker look like and what are its components?
The MT510 3G Personal Tracker is a compact device with the following visible components:
Speaker
SOS button
SIM Card port
Micro USB port
Microphone
3G LED
GPS LED
Charge LED
What precautions should be taken before installing the SIM card?
Before installing the SIM card, pay attention to the following:
Ensure the SIM card has enough balance.
Ensure the SIM card enables caller ID and GPRS function.
Ensure the SIM card disables PIN password and call forwarding function.
How do I install the SIM card?
To install the SIM card:
Get ready a Standard SIM Card.
Insert the SIM Card to the slot.
What happens after inserting the SIM card?
The device will POWER ON automatically after inserting the SIM card.
What do the different statuses of the 3G Indicator (Blue) mean?
| Status | Description |
|---|---|
| Always ON | No SIM Card or no network |
| Slow flash (8s/time) | Work mode |
What do the different statuses of the GPS Indicator (GREEN) mean?
| Status | Description |
|---|---|
| Always OFF | GPS unavailable |
| Quick flash (1s/time) | GPS available |
What do the different statuses of the Charge Indicator (YELLOW/RED) mean?
| Status | Description |
|---|---|
| Always ON(Yellow) | Under charging |
| Light bright(Yellow) | Charging completed |
| Slow lash(Red) | Low battery |
What is the instruction for the Power Button?
| Button | Description |
|---|---|
| Power Button | Insert the SIM card to POWER ON, take out SIM card to POWER OFF. |
What are the functions of the SOS Button?
Press and hold button for 3 seconds (vibrate twice), the unit will call the authorized phone numbers by sequences and send position to authorized phone numbers and upload data to server.
Short press button for 1 second (vibrate one time) to hang up/Answer or the call (incoming or Speaking).
How do I set an authorization phone number?
Instruction format: *cell phone number *password*serial number(1-3)**
For example: *13424392330*0000*1**
Reply: SET USER NUMBER 1 OK.
Note:
The defaulted password is 0000.
It can authorize up to 3 phone numbers.
How do I delete an authorization number?
Instruction format: **password*number(1-3)**
For example: **0000*1**
Reply: DELETE USER NUMBER 1 OK.
How do I change the device password?
Instruction format: 777+new password+old password
For example: 77712340000
Reply: SET USER PASSWORD OK.
How do I perform a single location inquiry?
Instruction format: 666+password
For example: 6660000
Description: Send this SMS command to unit, it will reply SMS as follows:
ID:865662000409210
Date:05:36:59 15/08/2015
Fix:A State:SMS
How do I enable or disable the calling switch?
To turn Calling OFF:
Instruction format: 150+password
For example: 1500000
Reply: SET VOICE CALL:OFF
To turn Calling ON:
Instruction format: 151+password
For example: 1510000
Note: If you do not want to get the Calling alert, send 1500000 to disable it.
How do I enable or disable SMS response?
To turn SMS OFF:
Instruction format: 160+ user password
For example: 1600000
Reply: SET SEND SMS:OFF.
To turn SMS ON:
Instruction format: 161+ user password
For example: 1610000
Reply: SET SEND SMS:ON.
Note: If you do not want to get the SMS alert, send 1600000 to disable it.
How do I enable or disable the call restriction switch?
To turn Call restriction OFF:
Instruction format: 170+password
For example: 1700000
Reply: SET INCOMING CALLS:OFF.
To turn Call restriction ON:
Instruction format: 171+password
For example: 1710000
Reply: SET INCOMING CALLS : ON
Note:
170 mode: it can only receive incoming call from 3 authorization numbers.
171 mode: the device can answer incoming call from any cell phone.
How does the phone positioning function work?
If an incoming call is from one of the 3 authorized numbers and it is hung up after ringing for 2-5 times, the device will send location to the authorized phone number and then upload data to the server, and the status is :CALL.
How does the SOS Alarm function work?
Press the SOS button for 3 seconds (vibrate twice), the device will call the authorized phone numbers and then send location to the authorized phone number and upload data to the server, the state is: SOS.
How do I enable or disable voice monitoring?
To Disable the monitor:
Instruction format: 000+password
For example: 0000000
Reply: SET VOICE MONITOR:OFF.
To Enable the monitor:
Instruction format: 001+password
For example: 0010000
Reply: SET VOICE MONITOR:ON.
Note: Default is MONITOR OFF.
How do I set up a Round Geo-fence?
Instruction format: 005+password+R+X
For example: 0050000R1.0
Note: X defines the radius in KM, ranging from 0.1 to 999.9.
How do I enable the Round Geo-fence?
Instruction format: 211+password
For example: 2110000
Reply: SET ROUND GEO-FENCE: ON.
How do I disable the Round Geo-fence?
Instruction format: 210+password
For example: 2100000
Reply: SET ROUND GEO-FENCE: OFF.
How do I set up a Square Geo-fence?
Instruction format: 006+password+G1,IO/I/O,E/W longitude upper limit+N/S latitude upper limit, E/W longitude lower limit+N/S latitude lower limit.
For example: 0060000G1,IO,E114.04540N22.59034,E114.05978N22.59797
Reply: SET SQUARE GEO-FENCE1(IO)OK.
How do I enable the Square Geo-fence?
Instruction format: 311+password
For example: 3110000
Reply: SET SQUARE GEO-FENCE: ON.
How do I disable the Square Geo-fence?
Instruction format: 310+password
For example: 3100000
Reply: SET SQUARE GEO-FENCE: OFF.
How does the low battery alarm work?
When the backup battery is low power, the device will send an SMS to the authorized phone number and upload data to the server. The state is: BLP.
How do I enable or disable the over-speed alarm?
To enable:
Command: #122#user password#X##
Example: #122#0000#100##
Reply: SET SPEED LIMIT:ON
To close:
Command: #122#0000#0##
SET SPEED LIMIT:OFF.
Note: X is the speed value, unit is KM/H, and the definition is [0, 999].
How do I set the time zone?
Instruction format: 896+password+ +/-HH:MM
For example: 8960000+08:00
Reply: SET TIME ZONE:+08:00
Note: The default is Greenwich time (UTC).
How do I set the GPRS user name?
Instruction format: #801#password#user name##
For example: #801#0000#MT500##
Reply: SET SERVER USER NAME OK.
How do I set the APN (Access Point Name)?
Instruction format 1: #803#user password#APN##
For example: #803#0000#CMNET##
Instruction format 2: #803#password#APN#APN user name# APN password##
For example: #803#0000#CMNET#INTERNET#INTERNET##
Reply: SET GPRS APN OK.
How do I set the Server IP and PORT?
Instruction format: #804#password#IP address(or domain) #port##
Example: #804#0000#112.95.164.248#7780## (or) #804#0000#e.trackits.com#7700##
Reply: SET SERVER IP AND PORT OK.
How do I set the GPRS Upload Interval Time?
Instruction format: #805#password#interval time#X##
For example: #805#0000#10#1##
Reply: SET GPS PERIODIC UPLOAD ON.
Note: The interval time is defined as [10,65535] seconds. X is defined as [0,1]. If X=0, it will stop upload and reply: SET GPS PERIODIC UPLOAD OFF.
How do I enable or disable Power Saving Mode?
To enable power save mode:
Instruction format: 100+password
For example: 1000000
Reply: SET POWER SAVE MODE:ON.
To disable power save mode:
Instruction format: 101+password
For example: 1010000
Reply: SET POWER SAVE MODE:OFF.
Note: Default is OFF.
How do I configure Power Saving Mode when the device is stopped?
Instruction format: #807#password#interval time##
For example: #807#0000#2##
Reply: SET GPS POWER SAVING UPLOAD ON.
Note:
Interval time is defined as [2,1440] minutes. If interval time is 0, it will stop upload and reply: SET GPS POWER SAVING UPLOAD OFF.
If you enable power saving mode (1000000) and the device is stopped, the device will upload as per the 807 command interval.
Upload status is AUTOLOW.
How do I configure Power Saving Mode when the device is moving?
Instruction format: #809#password#interval time#X##
For example: #809#0000#10#1##
Reply: SET GPS TOWED UPLOAD ON.
Note:
Interval time is defined as [10,65535] seconds. X is defined as [0,1]. If X=0, it will stop upload and reply: SET GPS TOWED UPLOAD OFF.
If you enable power saving mode (1000000) and the device is moving, the device will upload as per the 809 command.
Upload status is TOWED.
How do I enable or disable Invalid GPS Data Upload?
To turn Invalid data upload ON:
Instruction format: 081+users password
For example: 0810000
Reply: INVALID DATA UPLOAD:ON
To turn Invalid data upload OFF:
Instruction format: 080+user password
For example: 0800000
Reply: INVALID DATA UPLOAD:OFF
How do I set the mileage report interval time?
Format: #141#password#X#Y##
For example: #141#0000#10#1##
Reply: SET GPS MILEAGE STATISTICS:ON/OFF
Note: X is the mileage value, defined as [0,1000]KM; Y is the alert mode, defined as [0,1], where Y=0 disables the alert and Y=1 enables the alert.
How do I clear the mileage data?
Format: #142#password#T##
For example: #142#0000#1##
Reply: SET GPS MILEAGE STATISTICS:CLEAR CURRENT/ALL
Note: T is [0,1]. T=0 clears current mileage; T=1 clears total mileage.
How do I check the current mileage?
Format: #143#password##
For example: #143#0000##
Reply: TOTAL GPS MILEAGE:X.X Km
CURRENT GPS MILEAGE:X.X Km
Note: mileage unit is KM.
What should I remember about my SIM card when using the tracker?
Please remember to monitor the credit balance of your SIM card to avoid confusion or delays in setting up your new unit. This can be a common issue, especially when initially setting up a new unit, and the unit fails to reply to a correct SMS command sequence.
CLICK HERE TO DOWNLOAD MICTRACK MT510 (01) PDF MANUAL