MI SCWXCQ01RR (01) PDF Document

Please adhere to the following usage restrictions for your MI SCWXCQ01RR:

• Use the vacuum for home and in-car purposes only. Do not use it in outdoor, commercial, or industrial environments.

• Do not store the vacuum in a car to prevent high or low temperatures from affecting its battery life.

• Avoid using the vacuum in environments with high humidity, or temperatures above 40°C or below 3°C.

• Supervise children to ensure they do not play with the appliance.

• Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts.

• When using an electric brush head, keep limbs and pets away from the rotating brush heads to prevent injury.

• Do not handle the power supply or operate the product with wet hands.

• Do not vacuum any liquids (like water or cola), burning or smoking substances (like non-extinguished cigarette butts), or hard or pointy objects (like building materials, glass, and nails).

• Use this product only in areas below 3,000 meters above sea level.

• The MI SCWXCQ01RR contains batteries that are only replaceable by skilled persons.

• Only charge the product using an ATC01RR or BTC01RR power supply.

• Do not use any third-party batteries, power adapters, or docking stations.

• Do not disassemble, repair, or modify the battery, power adapter, or docking station.

• Do not charge the vacuum or install the docking station near heat sources (like radiators) or in humid areas (like bathrooms).

• Do not wipe the adapter or docking station with a wet cloth or touch them with wet hands.

• If the power cord is damaged or broken, stop using it immediately and contact after-sales service.

• If the vacuum will not be used for an extended period, fully charge it, unplug the power supply, and store it in a cool, dry place. Recharge it once every three months to prevent the battery from over-discharging.

The following steps are only applicable for scrapping the MI SCWXCQ01RR. The battery must be removed from the appliance before it is scrapped, and the appliance must be disconnected from the supply mains when removing the battery. Dispose of the battery safely by leaving it with a professional organization.

1. Remove the dust compartment and cyclone assembly. Then, remove the two screws on the inner wall of the vacuum near the dust compartment release switch.

2. Remove the top fan filter, and then remove the screw used for fixing the cover of the handle on the inner wall of the vacuum.

3. Open the handle cover along the gap at the top of the handle and gently slide it up to remove the cover.

4. Unplug the 3 connectors inside the handle from the battery.

5. Slide out the battery pack.

On/Off Switch:

• Push to turn on.

• Release to turn off.

MAX Button:

• Press and hold the On/Off switch, then press the Max button to change to the vacuum’s MAX mode.

• Note: In MAX mode, the fan runs at full speed, reducing battery life and blowing out hot air. Turning off the vacuum reverts it to Standard mode.

MAX-LED: MAX mode indicator:

• Off: Standard Mode

• On: MAX mode

LED Battery Status Indicator:

• Red: Battery level < 20%

• Orange: Battery level of 20 – 60%

• White: Battery level > 60%

• Off: Battery is fully charged or the vacuum is turned off.

• Slowly Blinking Orange: Temporary protection if the battery temperature is too high or too low. Wait for the battery temperature to return to normal before using or charging.

• Slowly Blinking Red: Low battery, please charge before use.

• Quickly Blinking Red: Indicates either a battery charging protection issue or a hardware error. For charging protection, unplug for one minute and plug it in again. For a hardware error, contact after-sales service.

You can connect accessories directly to the main vacuum body or via the extension rod.

To Install:

Align the accessory (like the floor attachment or crevice nozzle) with the connector on the vacuum or extension rod and push it in until it clicks into place.

To Remove:

Push down the quick release switch on the connector and pull the accessory away to remove it.

You can charge the MI SCWXCQ01RR either directly with the power supply or via the docking station (sold separately).

The LED Battery Status Indicator shows the charging status:

• Red: Battery level < 20%

• Orange: Battery level of 20 – 60%

• White: Battery level > 60%

• Off: Battery is fully charged or the vacuum is turned off.

Notes on Charging:

1. When using the vacuum for the first time, it is recommended to fully charge it before use.

2. When charging, the vacuum will stop operating and automatically enter Charging mode.

3. After continuous use in MAX mode, the battery will be hot, which increases charging time. It is recommended to let the vacuum cool down for 30 minutes before charging it.

• Some carpets may fluff when vacuumed. If this happens, it is recommended to use the brush or crevice nozzle.

• Before vacuuming highly polished floors (wooden or polished tiles), check the floor brush for foreign objects to avoid scratching.

• Ensure the dust compartment is installed before use.

• Do not block the exhaust port when vacuuming.

• For fine dust like flour, use the vacuum for small amounts only.

• Do not vacuum sharp objects, small toys, pins, or paper clips to avoid damage.

• When cleaning dangerous areas like stairs and windows, pay attention to personal safety.

• Do not place the vacuum on tables or chairs, or lean it against items to avoid damage from dropping or slipping.

• The brush movement may cause an uneven gloss on waxed floors. If this occurs, wipe the floor with a damp cloth and polish it with wax.

1. If any of the rotating parts get stuck, the product may automatically turn off. It can be used again after all foreign objects are removed.

2. When the motor enters overheating protection mode, it will automatically turn off and stop operating. Wait for the temperature of the electric brush head to cool down before using it again.

• Crevice Nozzle: Suitable for vacuuming narrow crevices such as around doors, windows, and dead corners of stairs.

• Brush Nozzle: Suitable for vacuuming sofas, seats, etc.

• Bed Attachment: Suitable for vacuuming dust and mites on textile surfaces such as beds and curtains.

• Floor Attachment: Suitable for vacuuming different types of floors.

Note: The Brush Nozzle can also be used independently to vacuum dust from the vacuum cleaner itself or electric brush heads.

• Always use genuine parts to avoid voiding the warranty.

• If the filter or nozzle is clogged, the fan will stop working shortly after turning on the vacuum. In this case, immediately rinse the filter, nozzle, etc.

• When the vacuum is not in use for an extended period, store it in a cool and dry place. Avoid direct sunlight or humid environments.

• If the vacuum is to be stored for a long time, fully charge it, unplug its power adapter, and recharge it once every three months to prevent the battery from over-discharging.

• To clean the vacuum body, wipe it with a soft dry cloth.

It is recommended to clean the dust compartment at least once a month.

1. Before cleaning, disconnect the adapter and ensure the vacuum is turned off. Empty the compartment as soon as dust reaches the “MAX” mark.

2. To empty, push the switch on the dust compartment in the direction of the arrow to open the bottom cover and empty it into a trash can.

3. To rinse, push the release switch next to the dust compartment and pull the compartment away from the vacuum.

4. Rinse the dust compartment with water. It is recommended to do this at least once a month. Wipe the contact points of the vacuum with a soft dry cloth if they are dirty.

5. After the dust compartment is completely dry, reinstall it on the vacuum.

Caution: Do not use detergents, polishes, or air fresheners to rinse the dust compartment. Do not rinse it in a dishwasher or any other device.

It is recommended to rinse the filter and cyclone assembly at least once a month. More frequent rinsing may be needed when cleaning fine dust or primarily using MAX mode.

Steps to Remove and Clean:

1. Ensure the vacuum is disconnected from the power supply. Remove the dust compartment.

2. Rotate the cyclone assembly counter-clockwise and remove it.

3. Remove the internal filter from the cyclone assembly.

4. Rinse the internal filter and cyclone assembly with tap water until they are clean. Wring out the filter after rinsing.

5. To thoroughly dry, keep the filter and cyclone assembly in a ventilated or cool place for at least 24 hours.

Caution: Do not rinse the filter in a dishwasher or washing machine, nor dry it in a tumble dryer, oven, microwave, or near an open fire.

Steps to Reinstall:

1. After drying, place the filter facing up on top of the cyclone assembly and gently push it into place, pushing aside the safety clip on the left side of the notch.

2. Align the cyclone assembly with the vacuum and turn it clockwise to lock it in place.

3. Slightly tilt the dust compartment when reinstalling it on the vacuum. Gently push it in the direction shown until you hear a click, indicating it is firmly secured.

It is recommended to rinse the top fan filter at least once a month.

1. Turn the top fan filter counterclockwise to the unlocked position and remove it from the vacuum.

2. Rinse the inside of the top filter under the tap. Rotate the filter while rinsing to ensure all dust in the filter gaps is rinsed out. Tap the filter several times against the sink to remove remaining dust.

3. Repeat this process four to five times until the filter is clean.

4. To thoroughly dry the filter, keep it in a ventilated or cool place for at least 24 hours.

5. After drying, reinstall the filter by aligning it with the unlocked position and turning it clockwise until it locks into place.

Before removing the roller, ensure the brush head is detached from the vacuum to avoid accidental activation.

Caution: The floor attachment contains electrical components and bearings; do not clean these parts with water.

1. Place the floor attachment facing you. Use a coin to turn the lock counterclockwise by 90° to the unlocked position.

2. Turn the end cap to the open position and gently slide the roller away from the head.

3. Separate the end cap from the roller and remove any hair wrapped around the roller and end cap.

4. After cleaning, install the end cap back on the roller.

5. Put the roller back into the attachment. Once the roller is in place, turn the end cap to the locked position.

6. Rotate the latch clockwise by 90° to the locked position to secure the roller.

Before removing the roller, ensure the brush head is detached from the vacuum to avoid accidental activation.

Caution: The bed attachment contains electrical components; do not clean these parts with water. The roller itself can be rinsed.

1. With the side latch of the brush head facing you, use a coin to turn the latch counterclockwise until it comes off.

2. After removing the latch, remove the roller from the bed attachment.

3. Rinse and clean the roller with water.

4. Place the roller vertically in a ventilated or cool place for at least 24 hours to dry thoroughly.

5. After confirming the roller is completely dry, put it back in place.

6. With the side latch facing you, use a coin to turn the latch clockwise into the locked position, ensuring the roller is securely in place.