MEDION E35 SW MD 18035 (01) PDF Document

The following items are supplied with your product:

• Robot vacuum cleaner with integrated lithium-ion battery pack
• 1 x charging station
• 1 x water tank
• 2 x mop attachments (1 x replacement mop attachment)
• 2 x filters (1 x replacement filter)
• 4 x side brushes (2 x replacement side brushes)
• 1 x remote control, incl. 2 x AAA batteries
• 1 x cleaning brush
• Short manual

Position the charging station on a wall with a level surface and avoid direct sunlight.

Ensure that the required clearance of approx. 0.5 m to the sides and approx. 1.5 m to the front is maintained and that the charging contacts for the robot vacuum cleaner are freely accessible.

Connect the mains adapter to the mains adapter connection on the charging station and connect the mains adapter to a socket.

The robot vacuum cleaner is fitted with a lithium-ion battery pack. Charge the appliance battery block for at least 6 hours the first time it is used to ensure that the full performance and longevity of the rechargeable battery is reached.

Place the robot vacuum cleaner onto the charging station so that the charging contacts lie on top of each other.

While the robot vacuum cleaner is charging, the battery status indicator light on the button flashes white at short intervals.

When the battery block is fully charged and charging is complete, the operating light lights up continuously.

The robot vacuum cleaner automatically returns to the charging station if the battery level is low. This return to the charging station interrupts the cleaning process.

1. Remove the battery compartment cover on the back of the remote control.

2. Insert two AAA/1.5 V batteries in the battery compartment of the remote control. Check the battery polarity (as shown on the bottom of the battery compartment).

3. Close the battery compartment.

1. Press the clock button on the remote control. The hour display flashes.

2. Increase or decrease the hour display using the control buttons (up/down).

3. Use the right control button to switch to the minute display. The minute display begins to flash.

4. Increase or decrease the minute value using the control buttons (up/down).

5. Press the clock button again to save the setting.

Note: Remove all rugs from the room before vacuuming. This robot vacuum cleaner is intended for use on hard floors. Ensure that the dust container is clean and that the filter has been correctly inserted.

1. Press the operating switch on the underside of the robot vacuum cleaner: Position I: ON; Position O: OFF.

2. Briefly press the button on the appliance or the button on the remote control to turn on the robot vacuum cleaner.

3. Press the button on the appliance or on the remote control to start the automatic cleaning process.

The button on the robot vacuum cleaner lights up white continuously during cleaning. The robot vacuum cleaner then automatically returns to the charging station.

To interrupt the automatic cleaning programme, press the button again or press the start/pause button on the remote control.

To continue cleaning, press the button again.

You can use the control buttons (up, down, left, right) to direct the robot vacuum cleaner around the room manually.

Change the vacuum power used directly on the robot vacuum cleaner by pressing and holding the button or using the fan button on the remote control. One beep indicates vacuum level 1 and two beeps indicate the use of vacuum level 2.

Press the button on the appliance for approx. 3 seconds or the button on the remote control to switch off the robot vacuum cleaner.

To use the robot vacuum cleaner for damp mopping, the water tank with wiping cloth must be used.

Important: Do not fill the water tank with distilled or demineralised water. Do not add strong or heavily foaming detergents, fragrances or similar substances, or solid cleaning additives to the water tank.

1. Lift the tab of the filling opening and fill the water tank with clean tap water. Close the filling opening with the tab.

2. Wet and wring the wiping cloth before use.

3. Slide the wiping cloth strip into the groove on the water tank.

4. Press the wiping cloth onto the water tank with the hook-and-loop fastener so that it lies smoothly.

1. Remove the dust container from the main appliance if you have not already done so.

2. Place the water tank with the mounting clips into the recesses on the dust container until the parts snap together.

3. Place the two connected parts into the main appliance with the wiping cloth pointing down.

4. Press the start/pause button to start wet cleaning.

To remove the mop attachment after cleaning, first remove the dust container/water tank and then pull off the mop attachment.

Empty the water tank and rinse the wiping cloth after every wet cleaning and allow it to dry.

The robot vacuum cleaner features various cleaning programmes that can be selected individually via the remote control:

Spot Cleaning Programme: Suitable for an area with a high concentration of dirt or dust. The robot concentrates on cleaning a particular area. Press the spiral button on the remote control to start.

Corner Cleaning Programme: Suitable for cleaning the corners and edges of a room. The product runs along a border (e.g. a wall). Press the square icon button on the remote control to start.

The timer function makes it possible for cleaning to take place automatically in a specified time window.

1. Press the schedule button on the remote control. The hour display flashes.

2. Use the up/down control buttons to set the hours.

3. Use the right control button to switch to the minute display. The minute display begins to flash.

4. Use the up/down control buttons to set the minutes.

5. Press the schedule button to complete and save the programming.

When the programmed time is reached, the robot vacuum cleaner automatically switches on and starts cleaning. If you switch off the robot vacuum cleaner using the operating switch, the stored settings are lost.

We recommend emptying the dust container and cleaning the filter after every use.

1. Press the release button on the dust container and pull the dust container (including the water tank if applicable) out to the front.

2. Lift up the dust container lid.

3. Empty the dust container over a dustbin.

4. Clean the dust container with the cleaning brush supplied.

5. Remove the HEPA filter and the sponge filter.

6. Tap or blow out the dust from the HEPA filter and sponge filter (using a hair dryer with cold air).

7. Rinse the dust container, HEPA filter and sponge filter thoroughly under running water. Note: The dust container is not suitable for cleaning in the dishwasher.

8. Allow the HEPA filter and sponge filter to dry overnight before using the filters again.

9. Once dry, insert the filters back into the dust container in reverse order.

1. Lift off the wiping cloth from the water tank and slide the wiping cloth strip out of the groove.

2. Rinse the wiping cloth under running water in between use. Wash the wiping cloths in the washing machine at max. 40°C.

3. Separate the water tank from the dust container.

4. Wash out the water tank with clean water and allow the water tank and wiping cloths to dry completely.

Clean the side brushes regularly.

1. Switch off the appliance and place it upside down onto a flat surface with the bottom of the appliance facing upwards.

2. If necessary, remove the side brush to make it easier to clean by releasing the screw on the brushes using a Phillips screwdriver.

3. Hold the side brushes firmly and pull them straight up to remove them from the appliance.

4. Remove dirt and hair from the side brushes.

5. After cleaning, reattach the side brushes.

Replace the brushes at intervals of 3-6 months depending on the degree of wear. If the bristles become bent, place the brushes in hot water so that the bristles return to their original shape.

If you are not going to use the appliance for a longer period of time, fully charge the battery, then completely disconnect the mains adapter and charging station from the power supply.

Clean the robot vacuum cleaner and store it in a dry, dust- and frost-free place, away from direct sunlight.

In case of non-use, fully charge the rechargeable battery every 2 months to prevent the battery from becoming fully discharged.

Remove the batteries from the remote control.

Caution: There is a risk of injury in case of contact with the removed batteries. Remove the battery pack before disposing of the robot or in case of a fault. Make sure the battery pack is completely discharged before removing.

1. Completely switch off the appliance via the operating switch, unplug the mains adapter from the socket, if necessary.

2. Loosen both screws on the battery compartment lid using a Phillips screwdriver and open the battery compartment.

3. Remove the battery pack by pulling on the tab.

4. Remove the battery block plug from the appliance socket and remove the rechargeable battery.

5. Connect the plug of the new battery block to the appliance socket.

6. Close the battery compartment and secure the battery compartment lid using the two screws.

7. Charge the battery and switch the appliance on again using the operating switch.