MAYTAG MLG30PD (01) PDF MANUAL

MAYTAG MLG30PD (01) PDF SUMMARY:

What does a blank display indicate?

This condition indicates that the appliance is inoperative. Enter setup mode to view diagnostic code.

---

What does “0 Minutes” showing in the display indicate?

This condition indicates that the appliance cannot be operated. Coins dropped or debit inputs during this condition will be stored in escrow but cannot be used until normal operation is restored by opening and then closing the door. If the door switch fails, it must be replaced before normal operation can be restored.

---

How is the appliance programmed at the factory for initial/first use?

The dryer is programmed with 6 minutes of dry time per quarter (coin 1) and a $0.25 dry price (fixed cycle with top off – PD Model).

---

What happens a few seconds after power is restored after a power failure?

If a cycle was in progress at the time of the power failure, the selected cycle will flash in the display. This indicates the need for a fabric setting keypad to be pressed to restart the dryer.

---

What does the display show after the door is opened following the completion of a cycle?

The display indicates the cycle price (unless set for free operation). As coins or debit inputs arrive, the display will change to lead the user through the initiation of a cycle.

---

What are the 4 types of pricing?

• Fixed “Vend” Pricing: A dryer set up for “Fixed Cycle” operation can only accept additional time accumulated by increments equal to the length of a complete dry cycle. A maximum of 99 minutes may be purchased; no additional credit is given when 99 minutes is in the display.
• Accumulator Pricing: If the price is set to one coin 1 and Fixed Cycle with Top Off option is selected then accumulator mode is in effect. Cycle time can be purchased one coin at a time up to the maximum time of 99 minutes. All money will be credited to a cycle with a single button press while in accumulator pricing.
• Fixed Cycle With Top Off Pricing: A dryer set to offer “Top Off” capability will allow time to be added to an existing dry cycle in increments equal to the number of minutes of dry time per quarter (coin 1), up to 99 minutes, regardless of the cost required to start the dryer. No credit is given for coins or debit inputs entered when the control is displaying 99 minutes.
• Free Cycles: This is established by setting the cycle price to zero. When this happens “SELECT CYCLE” will appear rather than a cycle price. Each press of a keypad will add the number of minutes of dry time per coin 1 to the time. Any cycle started as a free cycle will automatically terminate when the door is opened.

---

What does the display show after the dryer has been installed and plugged in for the first time?

The display will show “0 minutes”.

---

What does the display show once the unit has been plugged in and the dryer doors opened and closed?

The display will show the price. In dryers set for free cycles the display will flash “SELECT CYCLE”.

---

What is the function of the fabric setting keypads and the digital display?

The fabric setting keypads along with the digital display are used to setup the dryer controls. The display can contain 3 numbers or letters and a decimal point. These are used to indicate the price, time remaining and setup codes and related code values available for use in programming the appliance.

---

How are the keypads used to program the controls?

• The WHITES & COLORS keypad is used to adjust the values associated with setup codes. Pressing the keypad will increment the value by 1. Rapid adjustment is possible by holding the keypad down.
• The PERMANENT PRESS keypad will advance you through the setup codes. Pressing the keypad will advance you to the next available setup code. Holding the keypad down will automatically advance through the setup codes at a rate of 1 per second.
• The DELICATES keypad is used to select or deselect options.

---

What is important to note before starting the setup?

Despite all the options available, an owner can simply choose to uncrate a new commercial dryer, hook it up, plug it in and have a unit which operates. PD units are preset at the factory for fixed cycle price with top off.

---

How is the setup code indicated?

The setup code is indicated by the left-hand character, and the setup code value is indicated by the two right-hand characters.

---

What should be noted about programming stacked dryers?

On stacked dryers, programming selections apply to both dryers.

---

How can the regular cycle price be adjusted?

The regular cycle price represents the number of quarters (coin 1); may be adjusted from 0-39. Advance from 0-39 by pressing WHITES & COLORS. It defaults to 1 quarter – $.25. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the regular dry time be adjusted?

The regular dry time represents the number of minutes per quarter (coin 1). It defaults to 6 minutes per coin. By pressing the WHITES & COLORS keypad you can adjust the value from 1-99 minutes. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the type of dryer pricing be set?

Use the DELICATE keypad to select between Fixed Cycle with Top Off or Fixed Cycle. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the cycle counter option be set?

This option is either SELECTED “ON” or NOT SELECTED, “OFF.” Not Selected, “OFF” Selected “ON” and not able to be deselected. Press DELICATES keypad 3 consecutive times to select “ON.” Once selected “ON” it cannot be deselected. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the money counter option be set?

This option is either SELECTED “ON” or NOT SELECTED, “OFF.” Not Selected, “OFF” Selected “ON.” Press DELICATES keypad 3 consecutive times to remove (Not Selected “OFF.”) Counter resets by going from “OFF” to “ON.” Press PERMANENT PRESS keypad once to advance to the next code.

---

How can you select the money counter option to be permanently on?

To select “ON” and not able to be deselected, first select “ON,” then within two seconds press DELICATES twice, WHITES & COLORS once, and exit setup mode.

---

How can special pricing options be set?

This option is either SELECTED “ON” or NOT SELECTED, “OFF.” Not Selected “OFF.” Selected “ON.” Press DELICATES keypad once for this selection. If SPECIAL PRICING OPTION is selected, you have access to codes 3 through 9. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the special cycle price be adjusted?

The special cycle price represents the number of quarters (coin 1); may be adjusted from 0-39. Advance from 0-39 by pressing WHITES & COLORS. It defaults to 1 quarter = $.25. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the special dry time be adjusted?

The special dry time represents the number of minutes per quarter (coin 1). It defaults to 6 minutes per coin. By pressing the WHITES & COLORS keypad you can adjust the value from 1-99 minutes. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the time-of-day clock, minutes set?

Select 0-59 minutes by pressing WHITES & COLORS keypad. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the time-of-day clock, hour set?

Select 0-23 hours by pressing WHITES & COLORS keypad. Note that it uses military time (24 hr. clock). Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the special price start hour set?

Select the start hour (0-23 hours) by pressing the WHITES & COLORS keypad. Note that it uses military time (24 hr. clock). Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the special price stop hour set?

Select the stop hour (0-23 hours) by pressing the WHITES & COLORS keypad. Note that it uses military time (24 hr. clock). Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the special price day set?

This represents the day of the week and whether special pricing is selected for that day. A number (9.10) followed by “0” indicates no selection that particular day. A number followed by an “S” indicates selected for that day (9.1S). Days of the week (1-7) are selected by pressing the WHITES & COLORS keypad.

---

What should be displayed when exiting setup code “9”?

It must show the current day of the week.

---

How can the vault viewing option be set?

This option is either SELECTED “ON” or NOT SELECTED, “OFF”. Not Selected, “OFF”. Selected “ON”. Press DELICATES keypad once for this selection. When selected, the money and/or cycle counter will be viewable (if counter is selected 90C and/or 1.0C or 1.C0), when the coin box is removed. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the value of coin 1 be set?

This represents the value of coin 1 in number of nickels. It defaults to 05 = $0.25. By pressing the WHITES & COLORS keypad you have the option of 1-99 nickels. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the value of coin 2 be set?

This represents the value of coin 2 in number of nickels. It defaults to 20 = $1.00. By pressing the WHITES & COLORS keypad you have the option of 1-99 nickels. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the coin slide option be set?

This option is either SELECTED “ON” or NOT SELECTED, “OFF”. Not Selected, “OFF”. Selected “ON”. Press DELICATES keypad 3 consecutive times for this selection. When the coin slide mode is selected, set b. equal to value of slide in nickels. Set code 6 XX (REGULAR CYCLE PRICE) and code 3.XX (SPECIAL CYCLE PRICE) to number of slide operations.

---

What happens if the installer sets up “CS” on a coin drop model?

It will not register coins.

---

How can the add coins option be set?

This option is either SELECTED “ON” or NOT SELECTED, “OFF”. This option causes the customer display to show the number of coins (coin 1) to enter, rather than the dollars-and-cents amount. Not Selected, “OFF”. Selected “ON”. Press DELICATES keypad 3 consecutive times for this selection. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the coin or debit option be set?

Both coin & debit selected. Coins selected, debit disabled. Debit Card selected, coin disabled. Press DELICATES keypad 3 consecutive times for this selection. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the price suppression option be set?

This option is either SELECTED “ON” OR NOT SELECTED, “OFF”. This option causes the customer display to show “AVAILABLE” or “ADD” rather than the amount of money to add. (Used mainly in debit installations.) Not Selected, “OFF”. Selected “ON”. Press PERMANENT PRESS keypad once to advance to the next code.

---

How can the clear escrow option be set?

This option is either SELECTED “ON” OR NOT SELECTED “OFF”. When selected, money held in escrow for 30 minutes without further escrow or cycle activity will be cleared. Not Selected, “OFF”. Selected “ON”. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the whites and colors temperature setting adjusted?

This represents the degrees in Fahrenheit temperature (plus 100 degrees). For example: 50 equals 150 degrees. By pressing the WHITES and COLORS keypad you can adjust the value from 100 degrees to 160 degrees. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the permanent press temperature setting adjusted?

This represents the degree in Fahrenheit temperature (plus 100 degrees). For example: 40 equals 140 degrees. By pressing the WHITES and COLORS keypad you can adjust the value from 100 degrees to 160 degrees. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the delicates temperature setting adjusted?

This represents the degrees in Fahrenheit temperature (plus 100 degrees). For example: 30 equals 130 degrees. By pressing the WHITES and COLORS keypad you can adjust the value from 100 degrees to 160 degrees. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the whites and colors cool down time adjusted?

This represents the number of minutes of cool down. For example: 02 equals 2 minutes of cool down time. By pressing the WHITES and COLORS keypad you can adjust the value from 2 to 3 minutes. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the permanent press cool down time adjusted?

This represents the number of minutes of cool down. For example: 03 equals 3 minutes of cool down time. By pressing the WHITES and COLORS keypad you can adjust the value from 2 to 3 minutes. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the delicates cool down time adjusted?

This represents the number of minutes of cool down. For example: 03 equals 3 minutes of cool down time. By pressing the WHITES and COLORS keypad you can adjust the value from 2 to 3 minutes.

---

How is the cycle counter displayed?

If cycle counter (90C) is selected, the following will display:

• Represents the number of cycles in HUNDREDS. 1 02 = 200
• Represents the number of cycles in ONES. 2 25 = 25 Total = 225 Cycles This is “VIEW ONLY” and cannot be altered. Press PERMANENT PRESS keypad once to advance to the next code.

---

How is the money counter displayed?

If money counter (1.0C or 1.C0) is selected, the following will display:

• Number of dollars in HUNDREDS Number of dollars in ONES. Number of CENTS 3 01 = 100 4 68 = 68 5 75 = 75 Total = $168.75 End of Setup Codes. Exit From Setup Mode.

---

How is diagnostic mode entered?

This mode is entered by depressing DELICATES for one second while in any of the setup codes one through six (or while dAS displays if operating with Maytag Data Acquisition setup) or with a diagnostic code present. Diagnostic codes are cleared on entry and all display segments should flash.

---

How is the diagnostic cycle started?

With all segments flashing, the diagnostic cycle is started by depressing the PERMANENT PRESS keypad. The cycle consists of seven minutes of heat and 2 minutes of cool-down.

---

How can the diagnostic cycle minutes be adjusted?

The WHITES & COLORS keypad will increment the diagnostic cycle minutes up to 99, then roll over to 2 minutes.

---

How can the diagnostic cycle be canceled?

The PERMANENT PRESS keypad will cancel this cycle and exit the diagnostic mode.

---

How is dryer help mode entered?

Dryer help mode is entered by pressing the WHITES & COLORS keypad while in special pricing option step 2.XX (or while dAS displays if operating with Maytag Data Acquisition setup).

---

How is the help mode exited?

Press the WHITES & COLORS keypad at any time to exit help mode.

---

How is information advanced in help mode?

Press the PERMANENT PRESS keypad to advance through the information.

---

What information is displayed in the help mode?

• Software revision.
• Upper or lower thermistor temperatures in °F are alternately displayed.
• Other display symbols and elements are mapped to reflect the state of various inputs and outputs as follows:
  • PRICE – upper motor trying to run
  • ADD – upper pocket heating
  • BATTERY – upper motor sensed
  • OR – lower motor trying to run
  • SELECT – lower pocket heating
  • CYCLE – lower motor sensed