MARANTZ SR5002 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD MARANTZ SR5002 (01) PDF MANUAL


PDF Content Summary: Model SR4002/SR5002 User Guide AV Surround Receiver

ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is adequate for such proof. FOR U.K. ONLY This undertaking is in addition to a consumer's statutory rights and does not affect those rights in any way. FRANÇAIS GARANTIE Pour des informations sur la garantie, contacter le distributeur local Marantz. CONSERVER L'ATTESTATION D'ACHAT L'attestation d'achat est la preuve permanente d'un achat de valeur. La conserver en lieu sur pour s'y reporter aux fi ns d'obtention d'une couverture d'assurance ou dans le cadre de correspondances avec Marantz. IMPORTANT Pour l'obtention d'un service couvert par la garantie, il incombe au client d'établir la preuve de l'achat et d'en corroborer la date. Le reçu ou la facture constituent des preuves suffi santes. DEUTSCH GARANTIE Bei Garantiefragen wenden Sie sich bitte an Ihren Marantz-Händler. HEBEN SIE IHRE QUITTING GUT AUF Die Quittung dient Ihnen als bleibende Unterlage für Ihren wertvollen Einkauf Das Aufbewahren der Quittung ist wichtig, da die darin enthaltenen Angaben für Versicherungswecke oder bei Korrespondenz mit Marantz angeführt werden müssen. WICHTIG! Bei Garantiefragen muß der Kunde eine Kaufunterlage mit Kaufdatum vorlegen. Ihren Quittung oder Rechnung ist als Unterlage ausreichend. NEDERLANDS GARANTIE Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke Marantz. UW KWITANTIE, KASSABON E.D. BEWAREN Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een waardevol artikel en dienen op een veilige plaats bewaard te worden voor evt, verwijzing bijv, in verbend met verzekering of bij correspondentie met Marantz. BELANGRIJK Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de consument een gedateerd bewijs van aankoop te tonen. Uw kassabon of factuurzijn voldoende bewijs. ESPAÑOL GARANTIA Para obtener información acerca de la garantia póngase en contacto con su distribuidor Marantz. GUARDE SU RECIBO DE COMPRA Su recibo de compra es su prueba permanente de haber adquirido un aparato de valor, Este recibo deberá guardarlo en un lugar seguro y utilizarlo como referencia cuando tenga que hacer uso del seguro o se ponga en contacto con Marantz. IMPORTANTE Cuando solicite el servicio otorgado por la garantia el usuario tiene la responsabilidad de demonstrar cuándo efectuó la compra. En este caso, su recibo de compra será la prueba apropiada. ITALIANO GARANZIA L’apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo previsto dalla legge, a partire dalla data di acquisto comprovata da un documento attestante il nominativo del Rivenditore e la data di vendita. La garanzia sarà prestata con la sostituzione o la riparazione gratuita delle parti difettose. Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manutenzione effettuata da personale non autorizzato o, comunque, da circostanze che non possano riferirsi a difetti di funzionamento dell’apparecchio. Sono inoltre esclusi dalla garanzia gli interventi inerenti l’installazione e l’allacciamento agli impianti di alimentazione. Gli apparecchi verranno riparati presso i nostri Centri di Assistenza Autorizzati. Le spese ed i rischi di trasporto sono a carico del cliente. La casa costruttrice declina ogni responsabilità per danni diretti o indiretti provocati dalla inosservanza delle prescrizioni di installazione, uso e manutenzione dettagliate nel presente manuale o per guasti dovuti ad uso continuato a fi ni professionali. SVENSKA GARANTI För information om garantin, kontakta Marantz lokalagent. SPAR KVITTOT Kvittot är ett inköpsbevis på en värdefull vara. Det skall förvaras säkert och hänvisas till vid försäkringsfall eller vidkorrespondens mod Marantz. VIKTIGT Fö att garantin skall gälla är det kundens sak att framställa bevis och datum om köpet. Kvitto eller faktura är tillräokligt bevis fö detta.

CE MARKING English The SR4002/SR5002 is in conformity with the EMC directive and low-voltage directive. Français Le SR4002/SR5002 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell SR4002/SR5002 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Nederlands De SR4002/SR5002 voldoet aan de EMC eisen en de vereisten voor laag-voltage. Español El SR4002/SR5002 está de acuerdo con las normas EMC y las relacionadas con baja tensión. Italiano Il SR4002/SR5002 è conforme alle direttive CEE ed a quelle per i bassi voltaggi. Svenska SR4002/SR5002 är tillverkad i enlighet med EMC direktiven och direktiven för lågvolt sutrusning. English WARNINGS - Do not expose the equipment to rain or moisture. - Do not remove the cover from the equipment. - Do not insert anything into the equipment through the ventilation holes. - Do not handle the mains cord with wet hands. - Do not cover the ventilation with any items such as tablecloths, newspapers, curtains, etc. - No naked fl ame sources, such as lighted candles, should be placed on the equipment. - When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area. - Make a space of about 0.2 meter around the unit. - No objects fi lled with liquids, such as vases, shall be placed on the equipment. - When the switch is in the OFF position, the equipment is not completely switched off from MAINS. - The equipment shall be installed near the power supply so that the power supply is easily accessible. - Do Not Touch Hot Spots During and Immediately After Use. - During and immediately after use, this product is hot in areas other than the controls and rear panel connection jacks. Do not touch hot spots and especially the top panel. Contact with hot areas can cause burns. Français AVERTISSEMENTS - Ne pas exposer l’appareil à la pluie ni à l’humidité. - Ne pas essayer de retirer le boîtier de l’appareil. - Ne rien insérer dans l’appareil par les orifi ces de ventilation. - Ne pas manipuler le cordon d’alimentation avec les mains mouillées. - Ne pas recouvrir les ouïes de ventilation avec un objet quelconque comme une nappe, un journal, un rideau, etc. - Ne placer aucune source de fl amme nue, comme une bougie allumée, sur l'appareil. - Pour mettre au rebut les piles usées, respecter les lois gouvernementales ou les règlements offi ciels concernant l’environnement qui s'appliquent à votre pays ou région. - Veiller à ce qu’aucun objet ne soit à moins de 0,2 mètre des côtés de l'appareil. - Aucun objet rempli de liquide, un vase par exemple, ne doit être placé sur l'appareil. - Lorsque l'interrupteur est sur la position OFF, l'appareil n'est pas complètement déconnecté du SECTEUR (MAINS). - L'appareil sera installé près de la source d'alimentation, de sorte que cette dernière soit facilement accessible. - Ne pas toucher aux zones chaudes pendant et immédiatement après l’utilisation. - Pendant l’utilisation et immediatement apres, cet appareil est chaud en dehors des commandes et des prises de raccordement arriere. Ne pas toucher aux zones chaudes, et particulièrement au panneau supérieur, pour éviter tout risque de brûlure. Deutsch WARNHINWEISE - Das Gerät nicht Regen oder Feuchtigkeit aussetzen. - Die Abdeckung nicht vom Gerät abnehmen. - Keine Gegenstände durch die Belüftungsschlitze stecken. - Das Netzkabel nicht mit feuchten oder nassen Händen anfassen. - Decken Sie die Lüftungsöffnungen nicht mit einem Tischtuch, einer Zeitung, einem Vorhang usw. ab. - Es dürfen keine Gegenstände mit offener Flamme, wie etwa brennende Kerzen, auf dem Gerät aufgestellt werden. - Beachten Sie bei der Entsorgung der verbrauchten Batterien alle geltenden lokalen und überregionalen Regelungen. - Auf allen Geräteseiten muß ein Zwischenraum von ungefähr 0,2 meter vorhanden sein. - Auf das Gerät dürfen keine mit Flüssigkeiten gefüllte Behälter, wie etwa eine Vase, gestellt werden. - Wenn der Schalter ausgeschaltet ist (OFF Position), ist das Gerät nicht vollständig vom Stromnetz (MAINS) abgetrennt. - Das Gerät sollte in der Nähe einer Netzsteckdose aufgestellt werden, damit es leicht an das Stromnetz angeschlossen werden kann. - Berühren Sie während oder unmittelbar nach dem Gebrauch keine heißen Stellen des Gerätes. - Während oder unmittelbar nach dem Gebrauch ist dieses Produkt mit Ausnahme der Bedienelemente und der Anschlussbuchsen auf der Rückseite heiß. Berühren Sie die heißen Stellen und insbesondere die Oberseite nicht. Der Kontakt mit heißen Flächen kann zu Verbrennungen führen.

Nederlands WAARSCHUWINGEN - Stel het apparaat niet bloot aan regen of vocht. - Verwijder de afdekplaat van het apparaat niet. - Duw niets door de ventilatieopeningen in het apparaat. - Raak het netsnoer niet met natte handen aan. - Bedek de ventilatieopeningen niet met enige voorwerpen, zoals tafelkleden, kranten, gordijnen, enz. - Plaats geen brandende voorwerpen, zoals kaarsen, op het apparaat. - Volg bij het weggooien van verbruikte batterijen de overheidswetgeving of milieuvoorschriften op die van kracht zijn in het land of de regio waarin u zich bevindt. - Zorg dat er 0,2 meter vrije ruimte rond het toestel is. - Plaats geen voorwerpen met een vloeistof erin, zoals een bloemenvaas, op het apparaat. - Als de schakelaar op OFF staat, is het apparaat niet volledig losgekoppeld van de netspanning (MAINS). - De apparatuur wordt in de buurt van het stopcontact geïnstalleerd, zodat dit altijd gemakkelijk toegankelijk is. - Raak hete gedeelten van het apparaat niet aan tijdens en onmiddellijk na het gebruik. - Tijdens en onmiddellijk na het gebruik is dit product heet, behalve in de omgeving van de bedieningstoetsen en de aansluitingen op het achterpaneel. Raak geen hete plekken aan, vooral niet het bovenpaneel. Contact met hete plekken kan brandwonden veroorzaken. Español ADVERTENCIAS - No exponga el equipo a la lluvia ni a la humedad. - No extraiga la tapa del equipo. - No introduzca nada en el interior del equipo a través de los orifi cios de ventilación. - No maneje el cable de alimentación con las manos mojadas. - No cubra la ventilación con objetos como manteles, periódicos, cortinas, etc. - No deben colocarse sobre el equipo elementos con fuego, por ejemplo velas encendidas. - Cuando se eliminen baterías usadas, deben cumplirse las reglamentaciones oficiales o las normas de protección medioambiental aplicables en su país o en su zona. - Deje un espacio de unos 0,2 metro alrededor de la unidad. - No se deben colocar sobre el aparato recipientes que contengan líquidos, como por ejemplo jarrones. - Cuando el interruptor está en la posición OFF, el equipo no está completamente desconectado de la alimentación MAINS. - El equipo se instalará cerca de la fuente de alimentación de manera que resulte fácil acceder a ella. - No tocar las áreas calientes mientras la unidad está en uso ni inmediatamente después. - Mientras esta en funcionamiento e inmediatamente despues de su uso, este producto presenta zonas calientes en diversas partes, no exclusivamente en el sector de los controles o en las conexiones del panel posterior. No tocar las áreas calientes, especialmente el panel superior dado que pueden producirse quemaduras. Italiano AVVERTENZE - Non esporre l’apparecchio alla pioggia o all’umidità. - Non rimuovere il coperchio dell’apparecchio. - Non introdurre oggetti all’interno dell’apparecchio attraverso i fori di ventilazione. - Non toccare il cavo di alimentazione con le mani bagnate. - Non coprire le fessure di ventilazione con tovaglie, giornali, tende od oggetti analoghi. - Non posare sull'apparecchio sorgenti di fi amme scoperte quali candele accese. - Smaltire le pile usate in conformità alle norme governative o disposizioni ambientali vigenti nel proprio paese o zona. - Lasciare 0,2 metro liberi tutto intorno l'unità. - Non mettere sull'apparecchiatura alcun contenitore di liquido, come ad esempio dei vasi. - Quando l'interruttore è nella posizione OFF, l'apparecchiatura non è completamente scollegata da MAINS. - L’apparecchio va installato in prossimità della fonte di alimentazione, in modo che quest’ultima sia facilmente accessibile. - Non toccare i punti caldi né durante, né immediatamente dopo l’uso. - Durante, e subito dopo l’utilizzo, questo prodotto risulta essere molto caldo in alcune sue parti come ad esempio i connettori del pannello posteriore. Non toccare i punti caldi e specialmente la superfi cie del pannello. Il contatto con parti calde può provocare ustioni. Svenska VARNINGAR - Utsätt inte utrustningen för regn eller fukt. - Ta inte bort utrustningens hölje. - För inte in föremål i utrustningen genom ventilationshålen. - Hantera inte nätsladden med våta händer. - Täck inte för ventilationsöppningarna med några föremål som till exempel bordsdukar, dagstidningar, gardiner e.d. - Inga föremål med öppen låga, som till exempel tända stearinljus, bör placeras på utrustningen. - Följ de lagar och miljöskyddsråd som gäller i det land eller område där du bor när du gör dig av med batterier. - Se till att det fi nns omkring 0,2 meter fri plats runt omkring enheten. - Inga objekt som är fyllda med någon vätska, till exempel blomstervaser, bör placeras på apparaten. - Även om strömbrytaren står i det avstängda läget OFF, så är utrustningen inte helt bortkopplad från det elektriska nätet (MAINS). - Utrustningen ska vara installerad nära strömuttaget så att strömförsörjningen är lätt att tillgå. - Vidrör inte varma punkter under och omedelbart efter användning. - Bortsett från kontrollerna och anslutningsuttagen på baksidan är den här produkten varm under och omedelbart efter användning. Vidrör inte varma punkter och särskilt inte ovansidan. Kontakt med varma ytor kan orsaka brännskador. AV_060126N1

INTRODUCTION Thank you for purchasing the Marantz SR4002/SR5002 Surround receiver. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the SR4002/ SR5002. As there are a number of connection and confi guration options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V specialist dealer. ACCESSORIES CHECK Before use, check the below accessories were included in the package. TABLE OF CONTENTS INTRODUCTION ....................................1 ACCESSORIES CHECK ....................................................1 TABLE OF CONTENTS .........................1 FEATURES .............................................2 DESCRIPTION ...................................................................2 BEFORE USE .........................................4 OPERATION OF REMOTE CONTROLLER ......................4 NAMES AND FUNCTIONS ....................5 FRONT PANEL (SR4002) ..................................................5 FRONT PANEL (SR5002) ..................................................5 H S I BASIC OPERATION (PLAYBACK) ......33 L SELECTING AN INPUT SOURCE ...................................33 G N SELECTING THE SURROUND MODE ...........................33 E NIGHT MODE ..................................................................33 ADJUSTING THE MAIN VOLUME ..................................33 ADJUSTING THE TONE (BASS & TREBLE) CONTROL 33 TEMPORARILY TURNING OFF THE SOUND ..................33 USING THE SLEEP TIMER .............................................33 VIDEO CONVERT ............................................................34 SURROUND MODE .............................35 OTHER FUNCTION ..............................38

Remote Controller AITP 1 SOURCE l/ SLEEPSET DISPLAY LEARN SEND OFF AM Loop Antenna FM Antenna FL DISPLAY AND INDICATOR ..........................................7 REAR PANEL (SR4002) .....................................................8 REAR PANEL (SR5002) .....................................................8 DISPLAY MODE ...............................................................38 RECORDING AN ANALOG SOURCE .............................38

CS II 4 M-CH ST 2 EX/ES 3 P.DIRECT dts SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO ON SURROUND

CL CH/CAT 7 7.1CH IN 5 STEREO 8 NIGHT VIRTUAL 6 T.MODE LIP SYNC/ INPUT REMOTE CONTROLLER ................................................10 BAND

OSD SPKR A/B MULTI/CAT 0 MUTE A/D +10 9 HT-EQ MEMO 4 P.SCAN 4 AC Power Cable INPUT ..............................................................................38

DISC+ CH-SEL BASS PRESET ANGLE T.TONE SETUP/ T.DISP TUNING PTY ENTER EXIT F.DIRECT M-SPKR MENU VOLLUME REMOTE CONTROL OPERATION .....12 GENERAL INFORMATION OF REMOTE CONTROLLER LISTENING THROUGH HEADPHONES .........................39 DOLBY HEADPHONE MODE .........................................39

TV TUNER BASS DVD V-OFF SUBTITLE ATT.AUDIO

TAPE AUX 1 SYSTEM REMOTE CONTROLLER RC5500SR CD CDR AUX 2 AMP VCR MD TREBLE DSS TO THE UNIT ...................................................................12 CONTROLLING MARANTZ COMPONENTS .................13 BASIC OPERATION .........................................................16 ATTENUATION TO ANALOG INPUT SIGNAL ................39 SPEAKER A/B ..................................................................39 7.1 CH INPUT ...................................................................39

AAA-size batteries ⋅ 2 Microphone MC-10 Front AUX Jack Cover PUSH User Guide A NOTE ABOUT RECYCLING This product’s packaging materials are recyclable and can be reused. This product and the accessories packed together are the applicable product to the WEEE directive except batteries. Please dispose of any materials in accordance with your local recycling regulations. When discarding the unit, comply with your local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes. CONNECTIONS ...................................18 SPEAKER PLACEMENT .................................................18 CONNECTING SPEAKERS .............................................18 CONNECTING AUDIO COMPONENTS ..........................19 CONNECTING VIDEO COMPONENTS ..........................20 CONNECTING HDMI COMPONENTS ............................21 ADVANCED CONNECTING ............................................22 CONNECTING THE REMOTE CONTROL JACKS .........22 CONNECTING THE ANTENNA TERMINALS .................23 CONNECTING FOR THE MULTI ROOM (SR5002 only) 24 CONNECTING OTHER EQUIPMENT .............................25 SETUP ..................................................26 ON SCREEN DISPLAY MENU SYSTEM ........................26 1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND COMPONENT VIDEO INPUT) .........................................27 2 SPEAKER SETUP ........................................................27 3 PREFERENCE .............................................................30 4 SURROUND .................................................................30 5 PL II (PRO LOGIC II) MUSIC PARAMETER ..............31 6 CS II (CIRCLE SURROUND II) PARAMETER ...........31 7 7.1 CH INPUT LEVEL ...................................................31 8 MULTI ROOM (SR5002 only) .......................................31 SIMPLE SETUP ....................................32 AUX2 INPUT .....................................................................40 HT-EQ (HOME THEATER EQUALIZER) .........................40 TV AUTO ON/OFF FUNCTION ........................................40 VIDEO ON/OFF ...............................................................40 LIP.SYNC (SR5002 only) ..................................................40 BASIC OPERATION (TUNER) .............41 LISTENING TO THE TUNER ...........................................41 PRESET MEMORY ..........................................................41 RDS OPERATION ............................................................43 MULTI ROOM SYSTEM (SR5002 ONLY) ..44 MULTI ROOM PLAYBACK USING THE MULTI ROOM OUT TERMINALS .............................................................44 MULTI ROOM PLAYBACK USING THE MULTI SPEAKER TERMINALS .....................................................................44 SURROUND SPEAKER B SYSTEM (SR4002 ONLY) ...............................45 ANOTHER ROOM PLAYBACK USING THE S (SURROUND) SPEAKER B TERMINALS .......................45 TROUBLESHOOTING .........................46 HDMI .................................................................................47 TECHNICAL SPECIFICATIONS ..........48 SETUP CODES ........................................I

1

FEATURES E N G L I This unit incorporates the latest generation of digital S H surround sound decoding technology such as Dolby Digital EX, Dolby Digital, DTS-ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby Pro Logic IIx (Movie, Music and Game), Circle Surround II (Cinema and Music). In addition, Marantz has focused on the future. By utilizing pre-out jacks, 7.1 direct inputs and a RS 232C communication port (SR5002 only), the unit is tomorrow’s technology, today! This unit features a fully discrete 7 channel amplifi er section capable of delivering 80 watts (SR4002)/90 watts (SR5002) of high-current amplification, for continuously clean and stable power into each of the 7 channels. It employs a massive EI power transformer in combination with oversized filter capacitors. This design confi guration is capable of a clear and powerful reproduction of the most demanding action movie soundtracks and full range (multichannel) music discs. Through its ability to generate very high output voltages, the unit can easily drive the most demanding speakers with optimum results. This unit incorporates the most advanced Digital Signal Processing circuitry, along with a Crystal® 192 kHz/24 bit D/A converter in each of the 7 channels. Independent power supply circuits are incorporated for the FL display, audio and video sections for maximum separation, clarity and dynamic range. Together with hand-selected customized components, all elements work in harmony to recreate the emotion, exactly as the artist had intended. This unit is designed and engineered with extensive feedback from custom installation experts, dealers and consumers. It features multi-room/multisource, a RS-232C communication port (SR5002 only), heavy duty speaker binding posts and an extensive array of both analog and digital inputs / outputs. With 6 assignable digital inputs (including Front Aux), 3 assingnable component inputs (SR5002), 5 assignable digital input (SR4002), Super Audio CD Multi Channel (7.1 channel) direct inputs video convert system and OSD output versatility is taken to a stunning new level. Furthermore, the unit can output the OSD information through the Y/C (S video) and composite video outputs. An easy-to-use universal remote controller allows full access to all of the operating functions and can be used for system operation as well. This unit has Simple Setup function for easy setup. You can setup all speaker settings by just selecting your room size and the number of your speakers with Simple Setup function. You can also setup customized settings just like conventional AV amplifi ers. • Dolby Digital EX, Dolby Digital , DTS ES (Discrete 6.1, Matrix 6.1, Neo: 6) • Dolby Headphone 2 • Dolby Pro Logic IIx (Movie, Music, Game) • Circle Surround II (Movie, Music, Mono) • HDCD decording • MRAC (Marantz Room Acoustic Calibration) available • Simple Setup Function • Improved Station Name Input Method, 50 Presets • Auto Adjust Function for Speaker Distance Settings (Delay Time) • LIP.SYNC Funciton (Audio delay) • 7 ⋅ 80 Watts (8 Ohm) (SR4002)/7 ⋅ 90 Watts (8 Ohm) (SR5002), Discrete Amplifi ers • High Power Current Feedback Circuitry • Massive Energy Power Supply, Huge EI Transformer, Large ELCO’s. • 192 kHz/24 bit Crystal® DAC for all 8 Channels • 32 bit Digital Surround Processing Chipsets • Large Heavy Duty Speaker Terminals for all Channels • Auto Input Signal Detection • Front AUX Input (Digital Camera, Portable DVD) • Video Off Mode • Set Up Menu via all Video Output (Composite, S Video and Component video) • Video convert system • RS-232C Terminal for System Control (SR5002only) • Universal remote control • HDMI (Ver. 1.1) 3 Input/1 Output (SR5002) 2 Input/1 Output (SR4002) DESCRIPTION Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending. DTS, DTS Digital Surround, ES, and Neo:6 are registered trademarks and the DTS logos, Symbol and DTS 96/24 are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved. • dts Digital Surround DTS was introduced in 1994 to provide 5.1 channels of discrete digital audio into home theater systems. DTS brings you premium quality discrete multichannel digital sound to both movies and music. DTS is a multichannel sound system designed to create full range digital sound reproduction. The no compromise DTS digital process sets the standard of quality for cinema sound by delivering an exact copy of the studio master recordings to neighborhood and home theaters. Now, every moviegoer can hear the sound exactly as the moviemaker intended. DTS can be enjoyed in the home for either movies or music on of DVD’s, LD’s, and CD’s. • dts Neo:6 The advantages of discrete multichannel systems over matrix are well known. But even in homes equipped for discrete multichannel, there remains a need for high-quality matrix decoding. This is because of the large library of matrix surround motion pictures available on disc and on VHS tape; and analog television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from two channel matrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, band limited surround it can be disappointing to users accustomed to discrete multichannel. Neo:6 offers several important improvements as follow, • Neo:6 provides up to six full-band channels of matrix decoding from stereo matrix material. Users with 6.1 and 5.1 systems will derive six and fi ve separate channels, respectively, corresponding to the standard home-theater speaker layouts. • Neo:6 technology allows various sound elements within a channel or channels to be steered separately, and in a way which follows naturally from the original presentation. • Neo:6 offers a music mode to expand stereo nonmatrix recordings into the fi ve- or six-channel layout, in a way which does not diminish the subtlety and integrity of the original stereo recording. • dts Digital Surround ES DTS-ES Extended Surround is a new multichannel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTS-ES Extended Surround greatly improves the 360-degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999. In addition to the 5.1 surround channels (FL, FR, C, SL, SR and LFE), DTS-ES Extended Surround also offers the SB (Surround Back) channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal formats with different surround signal recording methods, as DTS ES Discrete 6.1 and DTS-ES Matrix 6.1. • dts Digital Surround 96/24 The stereo CD is a 16-bit medium with sampling at 44.1 kHz. Professional audio has been 20- or 24- bit for some time, and there is increasing interest in higher sampling rates both for recording and for delivery into the home. Greater bit depths provide extended dynamic range. Higher sampling rates allow wider frequency response and the use of anti alias and reconstruction fi lters with more favorable aural characteristics. DTS 96/24 allows for 5.1channel sound tracks to be encoded at a rate of 96kHz/24bits on DVD-Video titles. When DVD-video appeared, it became possible to deliver 24-bit, 96 kHz audio into the home, but only in two channels, and with serious limitations on picture. This capability has had little use. DVD-audio allows 96/24 in six channels, but a new player is needed, and only analog outputs are provided, necessitating the use of the D/A converters and analog electronics provided in the player. DTS 96/24 offers the following: 1. Sound quality transparent to the original 96/24 master.

2

2. Full backward compatibility with all existing decoders. (Existing decoders will output a 48 kHz signal) 3. No new player required: DTS 96/24 can be carried on DVD-video, or in the video zone of DVD-audio, accessible to all DVD players. 4. 96/24 5.1-channel sound with full-quality full motion video, for music programs and motion picture soundtracks on DVD-video. Dolby Digital identifi es the use of Dolby Digital audio coding for such consumer formats as DVD and DTV. As with fi lm sound, Dolby Digital can provide up to fi ve full-range channels for left, center, and right screen channels, independent left and right surround channels, and a sixth (“.1”) channel for low-frequency effects. Dolby Surround Pro Logic II is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround program material; provides a convincing three-dimensional soundfi eld on conventional stereo music recordings; and is ideally suited to bring the surround experience to automotive sound. While conventional surround programming is fully compatible with Dolby Surround Pro Logic II decoders, soundtracks will be able to be encoded specifi cally to take full advantage of Pro Logic II playback, including separate left and right surround channels. (Such material is also compatible with conventional Pro Logic decoders.) Dolby Digital EX creates six full-bandwidth output channels from 5.1-channel sources. This is done using a matrix decoder that derives three surround channels from the two in the original recording. For best results, Dolby Digital EX should be used with movies soundtracks recorded with Dolby Digital Surround EX. About Dolby Pro Logic IIx Dolby Pro Logic IIx technology delivers a natural and immersing 7.1-channel listening experience to the home theater environment. A product of Dolby’s expertise in surround sound and matrix decoding technologies, Dolby Pro Logic IIx is a complete surround sound solution that maximizes the entertainment experience from stereo as well as 5.1-channel encoded sources. Dolby Pro Logic IIx is fully compatible with Dolby Surround Pro Logic technology and can optimally decode the thousands of commercially available Dolby Surround encoded video cassettes and television programs with enhanced depth and spatiality. It can also process any high-quality stereo or Advanced Resolution 5.1-channel music content into a seamless 6.1- or 7.1-channel listening experience. The Dolby Headphone technology provides a surround sound listening experience over headphones. When listening to multichannel content such as DVD movies over headphones, the listening experience is fundamentally different than listening to speakers. Since the headphone speaker drivers are covering the pinna of the ear, the listening experience differs greatly from traditional speaker playback. Dolby utilizes patented headphone perspective curves to solve this problem and provides a non-fatiguing, immersive, home theater listening experience. Dolby Headphone also delivers exceptional 3D audio from stereo material. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. Circle Surround II (CS-II) is a powerful and versatile multichannel technology. CS-II is designed to enable up to 6.1 multichannel surround sound playback from mono, stereo, CS encoded sources and other matrix encoded sources. In all cases the decoder extends it into 6 channels of surround audio and a LFE/subwoofer signal. The CS-II decoder creates a listening environment that places the listener “inside” music performances and dramatically improves both hi-fi audio conventional surround-encoded video material. CS-II provides composite stereo rear channels to greatly improve separation and image positioning – adding a heightened sense of realism to both audio and A/V productions. CS-II is packed with other useful feature like dialog clarity (SRS Dialog) for movies and cinema-like bass H enrichment (TruBass). CS-II can enable the dialog S I to become clearer and more discernable in movies L and it enables the bass frequencies contained in G N the original programming to more closely achieve E low frequencies – overcoming the low frequency limitations of the speakers by full octave. Circle Surround II, Dialog Clarity, TruBass, SRS and symbol are trademarks of SRS Labs, Inc. Circle Surround II, Dialog Clarity and TruBass technology are incorporated under license from SRS Labs, Inc. HDCD® (High Defi nition Compatible Digital ®) is a patented process for delivering on Compact Disc the full richness and details of the original microphone feed. HDCD encoded CDs sound better because they are encoded with 20-bits of real musical information as compared to 16-bits for all other CDs. HDCD overcomes the limitation of the 16-bit CD format by using a sophisticated system to encode the additional four bits onto the CD while remaining completely compatible with the CD format. When listening to HDCD recordings, you hear more dynamic range, a focused 3-D sound stage, and extremely natural vocal and musical timbre. With HDCD, you get the body, depth and emotion of the original performance not a fl at, digital imitation. HDCD system manufactured under license from Microsoft. This product is covered by one or more of the following: In the United States 5,479,168 5,638,074 5,640,161 5,808,574 5,838,274 5,854,600 5,864,311 5,872,531 and in Australia 669,114 with other patents pending. HDMI, the and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

3

BEFORE USE E N G This section must be read before any connection is L I made to the mains supply. S H EQUIPMENT MAINS WORKING SETTING Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. SR4002/SR5002 can be powered by 230V AC only. COPYRIGHT Recording and playback of any material may require consent. For further information refer to the following: — Copyright Act 1956 — Dramatic and Musical Performers Act 1958 — Performers Protection Acts 1963 and 1972 — Any subsequent statutory enactments and orders DO NOT LOCATE IN THE FOLLOWING PLACES KEEP OBJECTS OFF Keep objects off the unit. Blocking the vent can result in accident and damage. DO NOT TOUCH HOT SPOTS DURING AND IMMEDIATELY AFTER USE During and immediately after use, the unit is hot in areas other than the controls and rear panel connection jacks. Do not touch hot spots and especially the top panel. Contact with hot areas can cause burns. OPERATION OF REMOTE CONTROLLER REMOTE CONTROL Operate the remote controller within a distance of approx. 5m from the infrared receptor window on the front of the unit. LOADING BATTERIES Before using the remote controller for the fi rst time, load the batteries in the remote controller. The batteries provided are used to verify the operations of the remote controller only. 1. Remove the battery cover. 2. Load the two new size “AAA” batteries inside the battery compartment while taking care to align their polarities correctly with the polarity markings ( with ( and with ). CAUTIONS ON BATTERIES • Use “AAA” type batteries in this remote controller. • We recommend that you use alkali batteries. • If the remote controller does not operate from close to the unit, replace the batteries with new ones, even if less then a year has passed. • The included battery is only for verifying operation. Replace it with a new battery as soon as possible. • When inserting the batteries, be careful to do so in the proper direction, following the + and - marks in the remote controller’s battery compartment. • To prevent damage or battery fl uid leakage: - Do not use a new battery with an old one. - Do not use two different types of batteries. - Do not short-circuit, disassemble, heat or dispose of batteries in fl ames. • Remove the batteries when not planning to use the remote controller for a long period of time. • If the batteries should leak, carefully wipe off the fl uid from the inside of the battery compartment, then insert new batteries. • When disposing of used batteries, please comply with governmental regulations or environmental

To ensure long-lasting use, do not locate the unit where: • Exposed to direct sunlight. Approx. 5 m MULTI STANDBY POWER ON/OFF INPUT SELECTOR AV SURROUND RECEIVER SR5002 M. SPEAKER B SETUP MIC PHONES public instruction’s rules that apply in your country or area. SURROUND MODE PURE DIRECT SIMP

AUT LE O SETUP HT-EQ MENU VOLUME DISPLAY ENTER • Near to sources of heat such as heaters. MEMORY DOWN EXIT CLEAR BAND T-MODE UP MUTE DIGITAL 7.1CH INPUT S-VIDEO • Highly humid or poorly ventilated. AUX 1 INPUT

VIDEO L AUDIO R

• Dusty. • Subjected to mechanical vibrations. • On wobbly, inclined or otherwise unstable surfaces • Radiated heat is blocked such as in cramped audio racks. SYSTEM REMOTE CONTROLLER RC5 0 SR Caution: 60° SR4002/SR5002 Remote controller 3. Close the battery cover until it clicks shut.

To ensure proper heat radiation, ensure the below clearance from walls and other equipment. 0.2 m (8 ins.) AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME 0.2 m (8 ins.) 0.2 m (8 ins.) DOWN UP • Do not allow direct sunlight, an inverter fl uorescent light or other strong source of light to shine onto the player’s infrared receptor window. Otherwise, the operation of the remote controller may be disabled. • Bear in mind that operating the remote controller may cause other devices operated by infrared rays to be operated by mistake. • The remote controller cannot be operated if the

MULTI STANDBY MULTI SPEAKER SURROUND MODE PURE DIRECT SIMPLE SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT space between the controller and the player’s

POWER ON/OFF PHONES SETUP MIC AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO 0.2 m (8 ins.) infrared receptor window is obstructed. • Do not place any objects on top of the remote controller. Doing so may cause one or more buttons to be held down which will cause the batteries to run down.

4

NAMES AND FUNCTIONS FRONT PANEL (SR4002) qw ui ! e rty ! o !0!1 !2 3 4 AV SURROUND RECEIVER SR4002 INPUT SELECTOR VOLUME q POWER switch and STANDBY indicator Press the button to turn the power ON, and press again to turn it OFF. If the POWER switch is in the ON position, the power of this unit can be turned ON/OFF by pressing the POWER button on the remote controller. When this unit is in the standby mode with the POWER switch set to the ON position, pressing the ENTER button also allows to turn the power on. The STANDBY indicator lights up when this unit y INFRARED receiving sensor window H S I This window receives infrared signals for the remote L control. G N E u SURROUND MODE button Press this button to select the surround mode. i PURE DIRECT button and indicator

DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG ATT is the standby mode (power OFF) by the remote SURROUND controller. When this button is pressed once, “SOURCE DIRECT”

SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 SPKR B EQ DIGITAL DIGITAL L C R appears on the FL display. If pressed again, “PURE

SURROUND PURE PCM SIMPLE LFE SL S SR DOWN UP w MULTI (Multi Room) button DIRECT” appears. After 2 seconds, the FL display indication goes out. In the source/pure direct mode, the tone control

7.1 CH INPUT STANDBY MODE S.SPEAKER B DIRECT SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT (SR5002 only) circuitry and bass management are bypassed.

AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO Press this button to activate the Multiroom system. “MULTI” indicator will be illuminated in the display. w 7.1CH INPUT button (SR4002 only) Press this button to select the output of an external multichannel player. Notes: • The surround mode is automatically switched to AUTO when the pure direct/source direct function is turned on. • Additionally, speaker configurations are fixed automatically as follows.

@4 @3@2 @1 @0 !9 !8!7 !5 !6 FRONT PANEL (SR5002) qw ui ! e rty ! o !0!1 !2 3 4 AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME e INPUT SELECTOR knob (AUDIO/ VIDEO) This knob is used to select the input sources. (See page 33) r M.(Multi Room) SPEAKER button (SR5002 only) Press this button to activate the Multiroom Speaker system. “MULTI” indicator will be illuminated in the display. (See page 44) Front SPKR = LARGE Center SPKR = LARGE Surround SPKR = LARGE Surround Back SPKR = LARGE Sub woofer = YES o SIMPLE SETUP button Press this button to enter the simple setup mode. You can setup the speaker conditions (speaker sizes, number of speakers, speaker delay times) quickly by pressing the cursor buttons. ! DISPLAY button 0

DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG ATT SURROUND Press this button to change the FL display mode.

SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 SPKR B EQ DIGITAL DIGITAL L C R

SURROUND PCM PURE SIMPLE LFE SL S SR DOWN UP r S.(Surround) SPEAKER B button (SR4002 only) Press this button to activate the Surround Speaker B (See page 38) ! MEMORY button 1

MULTI MULTI SPEAKER STANDBY MODE DIRECT SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT system . “SPKR B” indicator will be illuminated in the Press this button to enter the tuner preset memory

AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF PHONES SETUP MIC AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO display. (See page 45) t HEADPHONE jack for stereo headphones This jack may be used to listen to the unit’s output numbers or station names. (See page 41) ! CLEAR button 2 Press this button to cancel the station-memory setting mode or preset scan tuning. (See page 42)

@4 !6@3@2 @1 @0 !9 !8!7 !5 through a pair of headphones. Be certain that the headphones have a standard 1 / 4” stereo phono plug.

5

! VOLUME control knob 3 E N This knob is used to adjust the overall sound level. G Turning the control clockwise increases the sound L level. (See page 33) I S H ! ATT (Attenuate) button 4 Press this button to reduce the analog audio signal input level by about half. “ATT” indicator will be illuminated in the display. (See page 39) ! AUX1 INPUT jacks 5 These auxiliary video/audio input jacks accept the connections of a camcorder, portable DVD, game etc. When not using these jacks, protect with the included jack covers. How to Attach the Front AUX Jack Cover BAND @ Cursor ( 0 1, 2, 3, 4) / ENTER button Press these buttons to operate the SETUP MAIN MENU and TUNER function. @ MENU button 1 Press this button to enter the SETUP MAIN MANU. @ HT-EQ button 2 Press this button to turn on or off HT(Home Theater)- EQ mode. This mode compensates for the audio portion of a movie sounding “bright”. “EQ” indicator will be illuminated in the display. (See page 40) @ AUTO (Auto surround) button 3 Press this button to select the AUTO mode from the surround modes. When this mode is selected, the unit determines the surround mode corresponding to a digital input signal automatically.

T-MODE DIGITAL PUSH PUS UP MUTE 7.1CH INPUT S-VIDEO AUX 1 INPUT VIDEO L AUDIO R @ SETUP MIC jack 4 Automatically measure speaker characteristics using the included microphone (MC-10). (See page 29)

Front AUX Jack Cover ! MUTE button 6 Press this button to mute the output to the speakers. Press it again to return to the previous volume level. ! T-MODE button 7 Press this button to select the auto stereo mode or mono mode when the FM band is selected. “AUTO” indicator will be illuminated in the display. (See page 41) ! BAND button 8 Press this button to switch between FM and AM in the TUNER mode. ! EXIT button 9 Press this button to exit from the SETUP MAIN MENU. 6

FL DISPLAY AND INDICATOR ¡ DIGITAL Input Indicator 3 This indicator is illuminated when a digital input has ¡ HDCD indicator 8 H This indicator is illuminated when the HDCD signal is S I

s a f h k¡0 ¡2 ¡4 d j l¡1 ¡3 ¡5 g SURROUND been selected. ¡ ANALOG input indicator 4 This indicator is illuminated when an analog input decoded from digital input signal. L G N ¡ Main Information Display 9 E This display shows messages relating to the status,

DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG ATT SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 SPKR B EQ DIGITAL DIGITAL ™0 L C R source has been selected. input source, surround mode, tuner, volume level or other aspects of unit’s operation.

PCM LFE SL S SR ¡ SIGNAL FORMAT indicators 5 2 DIGITAL This indicator is illuminated when a Dolby Digital ™ DIRECT (Puredirect) indicator 0 This indicator is illuminated when this unit is in the

¡9 a DISP (Display Off) indicator ¡8 ¡7 ¡6 j V (video)-OFF mode indicator signal is input. EX This indicator is illuminated when a Dolby Digital EX signal is input. dts This indicator is illuminated when a DTS signal is SOURCE DIRECT or PURE DIRECT mode.

This indicator is illuminated when this unit is in the display off mode. s SLEEP timer indicator This indicator is illuminated when the sleep timer function in the main-room is in use. d Multi-room system indicator This indicator is illuminated when the multi-room system is active. f AUTO SURR (Auto Surround mode) indicator This indicator is illuminated to show that the AUTO SURROUND mode is in use. g TUNER’s indicators AUTO : This indicator illuminates when the tuner’s Auto mode is in use. TUNED : This indicator illuminates when the tuner receives a suffi ciently strong radio signal. ST(Stereo) : This indicator illuminates when an FM station is being tuned into stereo condition. h DTS-ES mode indicators (DISC6.1, MTX6.1) These indicators will illuminate to show the DTS-ES decoding mode (Discrete 6.1 or Matrix 6.1). This indicator is illuminated when the Video-OFF function is active. k NIGHT mode indicator This indicator is illuminated when this unit is in the Night mode, which reduces the dynamic range of digital program material at low volume levels. l SPKR (speaker) AB indicator This indicator is illuminated when the M (Multiroom) speaker B system is active. (SR4002 only) It displays the speaker system in use (A or B). When the speakers are not in use, both lights (A and B) will be turned off. (SR5002 only) ¡ PEAK indicator 0 This indicator is a monitor for an analog audio input signal. If the selected analog audio input signal is greater than the capable level of internal processing, this will illuminate. If this happens, you should press the ATT button. ¡ EQ mode indicator 1 This indicator is illuminated when the HT-EQ function is active. ¡ ATT (Attenuation) indicator 2 This indicator is illuminated when the attenuation function is active. input. ES This indicator is illuminated when a DTS ES signal is input. 96/24 This indicator is illuminated when a DTS 96/24 signal is input. PCM This indicator is illuminated when the input signal is PCM (pulse code modulation). 2 SURROUND This indicator is illuminated when a Dolby Surround signal is input. ¡ HDMI indicator 6 This indicator is illuminated when input terminal of the HDMI component is connected to the unit. ¡ ENCODED CHANNEL STATUS 7 indicators These indicators display the channels that are encoded with a digital input signal. If the digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”, “SR” and “LFE” will be illuminated. If the digital input signal is 2 channel PCM-audio, “L” and “R” will be illuminated. If the digital input signal is Dolby Digital 5.1ch signal with Surround EX fl ag or DTS-ES, “L”, “C”, “R”, “SL”, “S” , “SR” and “LFE” will be illuminated.

7

EN G REAR PANEL (SR4002) q VIDEO IN/OUT (TV, DVD, VCR, DSS) t MONITOR OUT This is a monitor output and each one includes both

w !1 q r !6

L I S H VIDEO t INPUT 1 !3 INPUT HDMI Ver 1.1 HDMI Ver 1.1 These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video confi gurations. Connect VCRs, DVD players, and other video components to the video inputs. composite video and S-video confi gurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections. FM (75) GND AM ANTENNA ANTENNA L SL C SBL L R S-VIDEO S-VIDEO INPUT 2 TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR 3COMPONENT COMPONENT VIDEO MONITOR MONITOR OUT Y CB/PB CR/PR IN 3 4 1 2 INPUT 1 INPUT 1 INPUT 2 INPUT 2 OUTPUT The 2 video output channels can be used to be connected to video tape recorders for making recordings. y Preamp Outputs (L, R, SL, SR, SBL, SBR, C) Jacks for L(front left), R (front right), C (Center), SL

R SR SW SBR IN OUT IN OUT IN OUT OPT OUT (surround left), SR (surround right), SBL (surround

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT TV DVD VCR TAPE

DSS L SL SBL C AUDIO CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. AC IN w FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial back left) and SBR (surround back right). Use these jacks for connection to external power

R SR SW SBR R L R L L R FRONT SURROUND BACK SURROUND BACK CENTER S. SPEAKER B S. SPEAKER BSURROUND SURROUND SPEAKER SYSTEMS : 6-8 OHMS SPEAKER SYSTEMS : 6-8 OHMS MODEL NO. SR4002 MODEL NO. SR4002 AC OUTLET AC OUTLET 230V 50/60Hz 230V 50/60Hz cable, or a cable network FM source. AM antenna and ground terminals amplifi ers. u AC INLET

PRE OUT PRE OUT SWITCHED SWITCHED 0.65A 150W 0.65A 150W Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM Plug the supplied power cable into this AC INLET and then into the power outlet on the wall. y !0 i u loop antenna will provide good AM reception in most This unit can be powered by 230V AC only.

!4 REAR PANEL (SR5002) o !5 areas. Position the loop antenna until you hear the best reception. e RS-232C (SR5002 only) The RS-232C port is to be used in conjunction with an external controller to control the operation of the i AC OUTLETS Connect the AC power cable of component such as a DVD or CD player to this outlet. This outlet provides power only when this unit is turned on.

!1 q r !6

w FM (75) GND AM ANTENNA ANTENNA !2 VIDEO S-VIDEO S-VIDEO t INPUT 1 1 INPUT COMPONENT COMPONENT HDMI Ver 1.1 HDMI Ver 1.1 INPUT VIDEO 3 MONITOR MONITOR OUT 2 SR5002 by using an external device. r COMPONENT VIDEO INPUT/ OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these Caution: • In order to avoid potential turn-off thumps, anything plugged into this outlet should be powered up before this unit is turned on. • The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more

2 INPUT 3 INPUT 3 OUTPUT

L SL C SBL L R TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR IN 4 5 1 2 3 INPUT 1 INPUT 1 INPUT 2 INPUT 2 component video connectors on the unit. This unit has two component video input connectors to obtain than the capacity of this outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power

R SR SW SBR MULTI. IN OUT IN OUT IN OUT OPT OUT FLASHER FLASHER the color information (Y, CB, CR) directly from the supply.

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT INDC

OUT RS-232C RS-232C SPEAKER C SPEAKER C OFF ON L SL SBL C TV DVD VCR TAPE DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. TRIGGER TRIGGER AC IN recorded DVD signal or other video component and one component video output connector to output it o Speaker outputs terminals

R L R L L L R R MODEL NO. SR5002 MODEL NO. SR5002 directly into the matrix decoder of the display device. By sending the pure DVD component video signal Seven terminals are provided for the front left,

FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER AC OUTLET AC OUTLET directly, the DVD signal forgoes the extra processing front right, front center, surround left, surround

R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER 230V 50/60Hz 230V 50/60Hz

PRE OUT PRE OUT SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS SWITCHED SWITCHED 0.65A 150W 0.65A 150W that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. right, surround back left and surround back right speakers. Note:

e !9 !4 y !0 i u!7!8 When the video convert function is enabled, video and

o !5 !3 S-video images can be output to the COMPONENT MOINTOR OUT jack. You can use surround back speaker terminals as M (Multiroom) SPEAKER B terminals, when you use no surround back speaker.

8

! Subwoofer Output 0 Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifi er is used, connect this jack to the subwoofer amplifi er input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifi er, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifi er. ! 7.1 CHANNEL or AUX2 INPUT 1 By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs. ! Multiroom Outputs (SR5002 only) 2 These are the audio output jacks for the Multi zone (Multi room). Connect these jacks to optional audio power amplifi ers to listen the source selected by the multiroom system in a remote room. ! REMOTE CONT. IN/OUT terminals 3 Connect to a Marantz component equipped with remote control (RC-5) terminals. ! AUDIO IN/OUT (CD, TAPE, CD-R, 4 TV, DVD, VCR, DSS) These are the analog audio inputs and outputs. There are 6 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. ! DIGITAL INPUT 5 (SR4002 : Dig.1 - 4, SR5002 : Dig.1-5) H S / OUTPUT (optical) I L These are the digital audio inputs and outputs. G The SR4002 has 2 digital inputs with coaxial jacks, 2 N E with optical jacks. The SR5002 has 2 digital inputs with coaxial jacks, 3 with optical jacks. The inputs accept digital audio signals from a CD, DVD, or other digital source component. For digital output, this is 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, or other similar components. ! HDMI INPUT/OUTPUT 6 The SR4002 has 2 HDMI inputs and 1 HDMI output. The SR5002 has 3 HDMI inputs and 1 HDMI output. The input function can be selected from the OSD menu system. (See page 27) ! DC TRIGGER output terminal 7 (SR5002 only) Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system OSD setup menu to determine the conditions by which these jack will be active. Note: This output voltage is for (status) control only, It is not suffi cient for drive capability. ! FLASHER IN 8 (Flasher input terminal) (SR5002 only) These terminals are to control the unit from each zone. Connect the control signal from a Keypad, etc. !9 SPEAKER C SELECTOR SWITCH (SR5002 only) The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 24.

9

REMOTE CONTROLLER E N The provided remote controller is a universal G L remote controller. The POWER button, numeric I S buttons and control buttons are used in common H across different input source components. The input source controlled with the remote controller changes when one of the input selector buttons is pressed. ‹5 z LEARN indicator Indicates when the remote controller is in the LEARN mode. x SET button This button is used to enter learn mode and preset mode. c / SOURCE ON/OFF button This button is used to turn a specifi c source (such as a DVD player) on or off independently from the rest 9/NIGHT button Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only in the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back. When this button is pressed, the “NIGHT” indicator is illuminated. 0/7.1CH IN button This button is used to select the output of an external ⁄ CONTROL buttons 3 These buttons are used when operating PLAY, STOP, PAUSE and other commands of a source. (When TUNER mode is selected) T.DISP button This button is used to select the display mode in RDS. PTY button This button is used to display the programme type information of the current station. F.DIRECT button This button is used to select the "Frequency direct

z x LEARN SEND ⁄7 ⁄8 of the system. multi channel decoder. (+10) A/D button input". PRESET +/- buttons

c SOURCE l/ SET OFF ON ⁄9 v SLEEP button This button is used to switch between the analog and digital inputs. This button is used to select a preset station up and down.

v b SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ ¤0¤1 This button is used for setting the sleep timer. TUNING +/- buttons

AUTO dts INPUT m CL (Clear) button

n 123 CS EX/ES VIRTUAL 456 M-CH ST STEREO NIGHT 789 BAND T.MODE P.SCAN ¤2 ¤3 b DISPLAY button This button is used to selects the display mode for the front display of the unit. This button is used to erase the memory or program of a source. This button is used to tune a frequency station up and down. ⁄ ANGLE/V-OFF buton 4

m 7.1CH IN A/D HT-EQ , SPKR A/B button (SR5002 only)

, CL CAT 0 +10 MEMO ¤4 ¤5 n Numeric buttons (When AMP mode is selected) CH/ . SPKR A/B MUTE VOLUME ¤6 These buttons are used to switch between 0 to +10 This button is used to select the speaker system. The speaker system is switched in the following This button is used to turn off the video signal.

⁄0 ⁄1 MULTI/ INFO CAT M-SPKR MENU ¤7¤8 of the source components. If the source is set to the amplifi er, these buttons are used to perform operations. (When AMP mode is selected) sequence. A → B → A+B → off ⁄ DISC+/CH. SEL button 5 (When AMP mode is selected)

⁄2 ⁄3 T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT ¤9 ‹0 1/AUTO button This button is used to select auto surround. 2/Dolby button This button is used to select DOLBY mode. . CH/CAT3 (UP) / 4 (DOWN) buttons These buttons are used to change channels. ⁄ MULTI/CAT button (SR5002 only) 0 This button is used to call up CH LEVEL ADJUST and adjust speaker levels or 7.1 ch input level. ⁄ BASS +/- buttons 6 These buttons are used to adjust the tone control

- ⁄4 PRESET + - TUNING + ‹1 3/dts button This button is used to select dts mode. (When AMP mode is selected) of low frequency sound for left, right and subwoofer

⁄5 ⁄6 DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE TV DSS ‹2 ‹3 4/CSII button This button is used to select CSII mode. 5/EX/ES button This button is used to turn on and off multi room. ⁄ INFO button 1 speaker. ⁄ SEND indicator 7

DVD VCR

TUNER CD CDR MD ‹4 This button is used to select EX/ES mode. (When AMP mode is selected) Indicates when the remote controller is transmitting

TAPE AUX1 AUX2 AMP 6/VIRTUAL button This button is used to select VIRTUAL mode. When this button is pressed, the current setting are displayed on the TV monitor. a signal.

REMOTE CONTROLLER 7/M-CH ST button This button is used to select Multi Channel Stereo. 8/STEREO button This button is used to select STEREO mode. ⁄ T.TONE/SET UP button 2 (When AMP mode is selected) This button is used to enter the test tone menu. (2-4 speakers level) ⁄8 / POWER ON and OFF buttons (When AMP mode is selected) These buttons are used to turn the unit on or off. ⁄ SURROUND button 9 This button is used to selects the surround mode.

10

¤ P.DIRECT button 0 When this button is pressed, the tone control circuit is bypassed. ¤ BAND/LIP SYNC/INPUT button 1 (When TUNER mode is selected) This button is used to select a radio band. (When AMP mode is selected) This button is used to select LIP SYNC mode. (When TV mode is selected) This button is used to select monitor input. ¤ T.MODE button 2 (When TUNER mode is selected) This button is used to select auto stereo mode or mono mode when the FM band is selected. The “AUTO” indicator lights in the auto stereo mode. ¤ P.SCAN button 3 (When TUNER mode is selected) This button is used to start preset scan. ¤ MEMO/HT-EQ button 4 This button is used to store setting to memory or program a source. (When AMP mode is selected) This button is used to turn on or off HT(Home Theater)-EQ mode. This mode compensates for the audio portion of a movie sounding “bright”. When this button is pressed, “EQ” indicator light up. ¤ MUTE button 5 This button is used to mute the audio for the amplifi er and television. Note: Set the AMP mode to use this button with the unit. ¤ VOLUME +/- buttons 6 This button is used to adjust the volume for the amplifi er and television. Note: Set the AMP mode to use this button with the unit. ¤ M-SPKR button (SR5002 only) 7 (When AMP mode is selected) This button is used to turn on and off multi speaker. ¤ MENU button 8 (When AMP mode is selected) This button is used to call up the SETUP MAIN MENU of the unit. ¤9 1,2,3,4(CURSOR) / ENTER buttons These buttons are used when controlling the cursor of the unit, DVD or other AV equipment. ‹ EXIT button 0 (When AMP mode is selected) This button is used to cancel setting in the setup menu. ‹ SUBTITLE/ATT. button 1 (When AMP mode is selected) When the input signal is too high and the voice distorts even by throttling the unit VOLUME control, turn on this function. “ATT” is indicated when this function is activated. The input level reduced. Attenuator is invalid for the output signal of “REC OUT”. Note: This function is unavailable while the digital input is selected. ‹ AUDIO buttons 2 H (When DVD mode is selected) S I This button is used to select one of the audio L language. G N E ‹ TREBLE +/- buttons 3 These buttons are used to adjust the tone control of high frequency sound for left and right speaker. ‹ SOURCE button 4 These buttons are used to switch the source of your A/V Receiver / amplifer. Each time a source button is pressed, the remote controller changes to the source which was pressed. This remote controller can control 12 types of equipment. To change the A/V Receiver / amplifi er source, press this button twice within two seconds. The signal is sent when it is pressed the second time. Notes: • Select the AMP as the source to use this remote controller with the unit. • In the case of the SR4002 or SR5002, the MD button cannot be used. ‹ Infrared Transmitter and Learning 5 Sensor This transmitter emits infrared light. Press the buttons while pointing the transmitter towards the infrared receiver window of the unit or other AV equipment. Be sure to also point towards other remote controllers when using the learning function.

11

REMOTE CONTROL OPERATION E N G L GENERAL INFORMATION OF REMOTE CONTROLLER TO THE UNIT I S H To control the unit by your remote controller, you have to select the device AMP or TUNER by pressing the SOURCE button. Please refer below for the details in AMP and TUNER mode. AMP MODE SOURCE ON / OFF Turns the SR4002/SR5002 on and off TUNER MODE 0-9 Inputs the numeric

LEARN SEND LEARN SEND POWER OFF Turns the SR4002/SR5002 off BAND Selects a radio band

SOURCE l/ SET OFF ON POWER ON Turns the SR4002/SR5002 on SOURCE l/ SET OFF ON T.MODE Selects the auto stereo mode or mono mode

SLEEP DISPLAY SURROUND P.DIRECT SLEEP Sets the sleep timer function SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ P.SCAN Starts preset scan

LIP SYNC/ AUTO dts INPUT

AUTO dts INPUT DISPLAY Changes the front display mode 1 2 3 CL Clears the inputting 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 BAND T.MODE P.SCAN P.DIRECT Selects the pure direct mode SURROUND Selects the surround mode CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 BAND T.MODE MEMO Enters the tuner preset memory numbers P.SCAN INFO Shows preset information

A/D 7.1CH IN HT-EQ AUTO (1) Selects auto surround A/D T.DISP Selects the display mode in RDS

7.1CH IN 0 +10 HT-EQ 0 +10 CL MEMO

CL MEMO CAT DOLBY (2) Selects DOLBY mode CAT CH/ SPKR A/B MUTE VOLUME PTY Displays the programme type information of the current station CH/ INFO SPKR A/B CAT MULTI/ MUTE M-SPKR VOLUME MENU dts (3) Selects dts mode CAT M-SPKR MULTI/ CSII (4) Selects CSII mode INFO MENU EX/ES (5) Selects EX/ES F.DIRECT Selects the “Frequency direct input” PRESET 3 / 4 Selects a preset station up and down TUNING 3 / 4 Tunes a frequency station up and down

T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT VIRTUAL (6) Selects VIRTUAL mode M-CH ST (7) Selects Multi Channel Stereo T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT

- PRESET + - TUNING + STEREO (8) Selects STEREO mode - NIGHT (9) Turns on or off NIGHT mode PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE 7.1CH IN (0) Selects the 7.1CH IN A/D (+10) Switches between the analog or digital inputs DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE TV DSS

TV DSS DVD VCR LIP SYNC / INPUT Selects the LIP SYNC mode

DVD VCR

TUNER CD CDR MD TUNER CD CDR MD

TAPE AUX1 AUX2 AMP HT-EQ Turns on or off HT-EQ mode AUX1 AUX2 AMP TAPE REMOTE CONTROLLER SPKR A / B Selects the speaker system MULTI / CAT Turns on or off multi room MUTE Decreases the sound temporarily M-SPKR Turns on or off multi speaker VOLUME 3 / 4 Adjusts the over all sound level INFO Displays the current setting on the monitor MENU Enters the "SETUP MENU" ENTER Enters the "SETUP MENU" Confi rms the setting in "SETUP MENU" mode CURSOR Moves the cursor for setting in "SETUP MENU" mode T.TONE / SET UP Enters the test tone menu EXIT Exits from SETUP MENU CH-SEL Calls up CH LEVEL ADJUST and adjusts speaker levels or 7.1ch input level V-OFF Turns on or off video output ATT. Reduces the input level BASS 3 / 4 Adjusts the tone control of low frequency sound TREBLE 3 / 4 Adjusts the tone control of high frequency sound SOURCE Selects a particular source component REMOTE CONTROLLER

12 CONTROLLING MARANTZ COMPONENTS H S 1. Press the desired SOURCE button. I L 2. Press the desired operation buttons to play the selected component. G • For details, refer to the component’s user guide. N E • It may not be possible to operate some models. CONTROLLING A MARANTZ DVD PLAYER (DVD MODE) CONTROLLING A MARANTZ VCR (VCR MODE) CONTROLLING A MARANTZ CD (CD MODE)

SOURCE l/ LEARN SET SEND OFF ON SOURCE ON / OFF Turns the DVD player on and off POWER OFF Turns the DVD player off POWER ON Turns the DVD player on 0-9,+10 Inputs the numeric SOURCE l/ LEARN SET SEND OFF ON SOURCE ON / OFF Turns the CD player on and off POWER OFF Turns the CD player off POWER ON Turns the CD player on 0-9 Inputs the numeric SOURCE l/ LEARN SET SEND OFF ON SOURCE ON / OFF Turns the VCR on and off 0-9,+10 Inputs the numeric LIP SYNC/INPUT Selects TV/VCR CL Clears the inputting

SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ CL Clears the inputting SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ CL Clears the inputting SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ MEMO Calls up programming menu

AUTO dts INPUT INPUT AUTO dts MEMO Calls up programming menu MEMO Programs AUTO dts INPUT CH 3 / 4 Selects VCR channel up or down 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 BAND T.MODE P.SCAN INFO Displays the disc information MENU Calls up the menu of DVD disc ENTER Enters the setting 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 BAND T.MODE P.SCAN INFO Scrolls the disc information MENU Switches the display information Pause Pause 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 BAND T.MODE P.SCAN MENU Calls up the menu ENTER Enters the setting CURSOR Moves the cursor for setting in

7.1CH IN A/D HT-EQ CURSOR Moves the cursor for setting in 7.1CH IN A/D HT-EQ Play Play 7.1CH IN A/D HT-EQ "On Screen Display" mode

0 +10 CL MEMO CAT "On Screen Display" mode CL CAT 0 +10 MEMO Stop Stop CL CAT 0 +10 MEMO EXIT Exits the programming menu

SPKR A/B CH/ CAT MULTI/ INFO MUTE M-SPKR VOLUME MENU T.TONE / SET UP Enters the test tone menu EXIT Exits from SETUP MENU T.Tone/Set up Calls up the setup menu of the DVD player SPKR A/B CH/ CAT MULTI/ INFO MUTE M-SPKR VOLUME MENU Previous/ Next Skips forward or previous track Rewind/ Forward Searchs forward or backward DISC+ CD changer next disc CH/ INFO SPKR A/B CAT MULTI/ MUTE M-SPKR VOLUME MENU REC Record Pause Pause Play Play Stop Stop

T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT Pause Pause T.TONE Play Play /SET UP Stop Stop REC Previous/Next Skips forward or previous ENTER EXIT T.DISP PTY F.DIRECT T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT Previous / Next Skips forward or previous track Rewind / Forward Searchs forward or backward AUDIO Selects the audio language

- PRESET + - TUNING + - chapter/track PRESET + - TUNING + - PRESET + - TUNING +

DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. Rewind/ Forward Searchs forward or backward DISC+ DVD changer next disc DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. DISC+ ANGLE SUB TITLE CH-SEL V-OFF ATT. AUDIO

BASS TREBLE TV DSS ANGLE Selects the camera angle BASS TREBLE TV DSS BASS TREBLE TV DSS

DVD VCR DVD VCR DVD VCR SUBTITLE Selects the subtitle language

TUNER CD CDR MD TUNER CD CDR MD TUNER CD CDR MD

TAPE AUDIO Selects the audio language

AUX1 AUX2 AMP TAPE AUX1 AUX2 AMP TAPE AUX1 AUX2 AMP

REMOTE CONTROLLER REMOTE CONTROLLER REMOTE CONTROLLER

13

E N G L I S H CONTROLLING A MARANTZ CD RECORDER (CDR MODE) SOURCE ON / OFF Turns the CD recorder on and off CONTROLLING A MARANTZ MD DECK (MD MODE) SOURCE ON / OFF Turns the MD deck on and off CONTROLLING A MARANTZ TAPE DECK (TAPE MODE) SOURCE ON / OFF Turns the TAPE deck on and off

SOURCE l/ LEARN SET SEND OFF ON POWER OFF Turns the CD recorder off POWER ON Turns the CD recorder on 0-9 Inputs the numeric SOURCE l/ LEARN SET SEND OFF ON POWER OFF Turns the MD deck off POWER ON Turns the MD deck on 0-9 Inputs the numeric SOURCE l/ LEARN SET SEND OFF ON POWER OFF Turns the TAPE deck off POWER ON Turns the TAPE deck on 0-9 Inputs the numeric

SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ CL Clears the inputting SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ CL Clears the inputting SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ CL Clears the inputting

AUTO dts INPUT MEMO Programs AUTO dts INPUT MEMO Programs AUTO dts INPUT MEMO Programs

1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 BAND T.MODE P.SCAN INFO Scrolls the disc information MENU Switches the display information REC Record 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 T.MODE P.SCAN MENU Switches the display information REC Record Pause Pause 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 T.MODE P.SCAN REC Record Pause Pause Play Play 7.1CH IN A/D HT-EQ Pause Pause 7.1CH IN A/D HT-EQ Play Play 7.1CH IN A/D HT-EQ Stop Stop CL CAT 0 +10 MEMO Play Play CL CAT 0 +10 MEMO Stop Stop CL CAT 0 +10 MEMO Previous / Next Skips forward or previous track

CH/ SPKR A/B MUTE VOLUME CH/ SPKR A/B MUTE VOLUME CH/ SPKR A/B MUTE VOLUME

MULTI/ INFO CAT M-SPKR MENU Stop Stop CAT M-SPKR MULTI/ Previous / Next Skips forward or previous track Rewind / Forward Searchs forward or backward INFO MENU Previous / Next Skips forward or previous track CAT M-SPKR MULTI/ Rewind / Forward Searchs forward or backward INFO MENU Rewind / Forward Searchs forward or backward

T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT

- PRESET + - TUNING + - PRESET + - TUNING + - PRESET + - TUNING +

DISC+ ANGLE SUB TITLE CH-SEL V-OFF ATT. AUDIO DISC+ ANGLE SUB TITLE CH-SEL V-OFF ATT. AUDIO DISC+ ANGLE SUB TITLE CH-SEL V-OFF ATT. AUDIO

BASS TREBLE TV DSS BASS TREBLE TV DSS BASS TREBLE TV DSS

DVD VCR DVD VCR DVD VCR TUNER CD CDR MD TUNER CD CDR MD TUNER CD CDR MD

TAPE AUX1 AUX2 AMP TAPE AUX1 AUX2 AMP TAPE AUX1 AUX2 AMP

REMOTE CONTROLLER REMOTE CONTROLLER REMOTE CONTROLLER

14 H S I L G N E CONTROLLING A MARANTZ UNIVERSAL DOCK (AUX1 MODE) SOURCE ON / OFF Turns the UNIVERSAL DOCK (Dock connector) ON and OFF

SOURCE l/ LEARN SET SEND OFF ON POWER OFF Turns the UNIVERSAL DOCK (Dock connector) OFF POWER ON Turns the UNIVERSAL DOCK (Dock connector) ON INFO Mode

SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ MENU Call up the menu

AUTO dts INPUT ENTER Enter the setting

1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 T.MODE P.SCAN CURSOR UP Select contents Up CURSOR DOWN Select contents Down Pause Pause 7.1CH IN A/D HT-EQ Play Play / Pause CL CAT 0 +10 MEMO Stop Stop

CH/ SPKR A/B MUTE VOLUME

MULTI/ INFO CAT M-SPKR MENU Previous/Next Skips forward or previous tracks P.SCAN Shuffl e

T.TONE /SET UP REC ENTER EXIT T.DISP PTY F.DIRECT

- PRESET + - TUNING +

DISC+ ANGLE SUB TITLE CH-SEL V-OFF ATT. AUDIO

BASS TREBLE TV DSS

DVD VCR TUNER CD CDR MD

TAPE AUX1 AUX2 AMP

REMOTE CONTROLLER 15

EN GL BASIC OPERATION NORMAL MODE Importants: • Some codes may be not match your equipment. In this case, you can use LEARN mode to store these codes. 2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking RESETTING THE CODE

IS SEND SEND LEARN LEARN twice. Then back light fl ushes.

(When operating Marantz AV equipment products) H This remote controller is preset with a total of • The preset codes do not cover full functions. If you need extra function, use LEARN mode to 3. Aim the remote control at the appliance and 1. SOURCE l/ SET OFF ON SOURCE l/ SET OFF ON

12 types of remote codes, including Marantz TV store extra function. slowly alternate between pressing CH+ button SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/

AUTO dts INPUT AUTO dts INPUT

(television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifi er). • Wen the batteries are getting weak, the preset procedure is not successful. and the SOURCE ON/OFF button for the appliance. 4. Stop when the appliance turns off. 123 DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. 123 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 789 T.MODE P.SCAN

A/D 7.1CH IN HT-EQ Learning is not necessary for Marantz products. You

can use these products without setting any codes. PROGRAMMING WITH THE 4-DIGIT CODE 5. Press ENTER button once to lock in the code. 1. BASS TREBLE TV DVD VCR DSS 2. 0 +10 CL MEMO CAT

TUNER CD CDR MD CH/ SPKR A/B MUTE VOLUME

1. Press the SOURCE button. - PRESET + - TUNING + 1. SOURCE l/ SET OFF ON CHECKING THE CODE TAPE AUX1 AUX2 AMP MULTI/ CAT M-SPKR

For this example, press DVD. DISC+ ANGLE SUB TITLE AUDIO SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ REMOTE CONTROLLER INFO MENU

CH-SEL V-OFF ATT. AUTO dts INPUT 1. Press and hold down the SOURCE button

Pressing the SOURCE button once changes 1 2 3 BASS TREBLE SOURCE l/ SET OFF ON

CS EX/ES VIRTUAL T.MODE 3. SLEEP DISPLAY SURROUND

P.DIRECT 1. P.SCAN

TV DVD VCR DSS 2. the remote control to the settings for the source 4 5 6 LEARN for appliance which should be controlled and SEND

TUNER CD CDR MD M-CH ST STEREO NIGHT AUTO dts LIP SYNC/ INPUT press SET button until the SEND indicator

that was pressed. TAPE AUX1 AUX2 AMP 7 8 9 SOURCE SET OFF ON 123

To change the amplifi er on other source, press 7.1CH IN 0 A/D +10 HT-EQ 1. l/ SLEEP DISPLAY SURROUND 4. CS EX/ES VIRTUAL 4 5 6 T.MODE blinking twice.

REMOTE CONTROLLER CL MEMO CAT P.DIRECT M-CH ST STEREO NIGHT P.SCAN Then back light fl ushes.

the SOURCE button twice (double-click). The SPKR A/B CH/ MUTE VOLUME AUTO LIP SYNC/ dts INPUT 789

123 code is sent, and then the amplifi er source A/D 7.1CH IN HT-EQ 2. Press the below codes to reset.

changes to DVD. 1. Press and hold down the SOURCE button for the 0 +10 CL MEMO CAT

SETTING THE BACK LIGHT appliance which should be controlled and press SET button until the SEND indicator blinks twice. 1. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE TV DVD VCR DSS CH/ INFO SPKR A/B CAT MULTI/ MUTE M-SPKR VOLUME MENU TV : 1000 DVD : 2000 VCR : 3000

Then back light fl ushes. TUNER CD CDR MD 2. DSS : 4000

Each time press the buttons, illuminate button 2 seconds. 2. Press the 4-digit code for appliance (code table AUX1 TAPE at the end of this book) AUX2 AMP T.TONE /SET UP ENTER EXIT The indicator will blink twice.

To turn off back light, press and hold down the SET and OFF button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ON button until SEND indicator blinks twice. Initial is back light ON. PRESET MODE (When operating non-Marantz AV equipment products) When the procedure is successful, the SEND indicator will blink twice. Note: If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again. SCANNING THE CODE TABLE REMOTE CONTROLLER 1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light fl ushes. 2. Press the INFO button. The SEND indicator will blink twice. 3. To view the code for fi rst digit, press 1 once. Wait 3 seconds, count the SEND indicator Note: After this procedure, the selected SOURCE button is set initial code.

This remote controller is preset with remote control SOURCE 3. l/ SEND LEARN SET OFF ON blinks (e.g. 3 blinks = 3) and write down the

codes from AV equipment by other manufacturers. The preset codes are TV, VCR, DVD and DSS. SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ number.

SOURCE SET OFF ON AUTO dts INPUT

Settings can be made in one of two ways. When the preset codes are set, the following codes 2. l/ SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ 123 CS EX/ES VIRTUAL 456 Note: T.MODE If a code digit is “0”, the SEND indicator will not

AUTO dts INPUT

are contained in the source button of the remote 123 CS EX/ES VIRTUAL T.MODE 3. M-CH ST STEREO NIGHT 789 P.SCAN blink.

456 7.1CH IN A/D HT-EQ

controller. 0 +10 CL MEMO CAT 4. Repeat step 3 three more times for remaining

DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. CH/ SPKR A/B MUTE VOLUME digits. Use 2 for the second digit, 3 for the third

See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and 2. BASS TREBLE TV DVD VCR DSS 5. INFO MULTI/ MENU CAT M-SPKR digit, and 4 for the fourth digit.

other settings. TUNER CD CDR MD

Remote controller Corresponding preset AUX1 TAPE Device name AUX2 AMP T.TONE ENTER source name code REMOTE CONTROLLER /SET UP EXIT

TV TV Television DVD DVD DVD player VCR VCR Video deck DSS SATELLITE Satellite broadcasting tuner equipment 1. Switch on the appliance which should be controlled.

16

LEARN MODE This remote controller is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote 4. Select the button to be learned. • LEARN indicator lights up. l/ SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ E R A S I N G P R O G R A M M E D C O D E S (RETURNING TO INITIAL SETTINGS) Codes can be erased in three ways: by buttons, sources, and by all memory contents. Erasing the code by buttons 3. Press ENTER button to continue erasing. • The SEND indicator blinks twice and the H S mode returns to LEARN mode. I L • To cancel the erasing operation, do not G press ENTER button and simply touch any N

AUTO dts INPUT

controller will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set 123 CS EX/ES VIRTUAL 456 T.MODE 1. Press and hold down the SET and MENU buttons until LEARN indicator blinks. other button. INFO E MENU

by the customer. The receiver sensor for the remote controller signals is 5. Press and hold the button of the original remote controller to learn until the SEND indicator SOURCE l/ MULTI/ CAT SET OFF ON M-SPKR ENTER

located at the top of the remote controller. Notes: blinks twice. SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ INFO MENU T.TONE /SET UP EXIT

Notes: AUTO dts INPUT

• This remote controller is capable to learn around 60 123 ENTER • When the SEND indicator blinks once, repeat this 4. To return the NORMAL mode, press the SET

codes. • When the batteries are getting weak , the learing procedure is not successful. step. • If the LEARN indicator fl ashes when the SEND indicator is lit, then the button cannot be learned. 2. Select the SOURCE button to select the button to be erased. BASS TREBLE TV DSS button. Erasing the all SOURCES

DVD VCR • When the memory of the remote controller is full,

LEARNING PROCEDURE the LEARN and SEND indicators blink once. If TUNER CD CDR MD 1. Press and hold down the SET and MENU 1. Place the remote controller so that its infrared you want to learn the code, you should erase other AUX1 TAPE learned button. AUX2 AMP buttons until LEARN indicator blinks.

signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a 6. Repeat steps 4 and 5 to learn other buttons in REMOTE CONTROLLER SOURCE l/ MULTI/ CAT SET OFF ON M-SPKR

distance of about 0.05 m (2 inches). same SOURCE. 7. Repeat steps 3 to 6 to learn other SOURCE. 3. Press and hold down the SLEEP button and press the learned button twice to be erased. SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ INFO MENU

AUTO dts INPUT

8. When you have finished programming the • SEND indicator blinks twice and the mode 123 ENTER

remote controller, press the SET button, then LEARN indicator stops blinking and exits from returns to LEARN mode. 2. Press and hold down the SLEEP button and press POWER ON and POWER OFF button.

0.05 m the LEARN mode. SOURCE l/ SET OFF ON • LEARN indicator lights.

LEARN SEND SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/

AUTO dts INPUT

SOURCE SET OFF ON 123 SOURCE l/ SET OFF ON

l/ SLEEP DISPLAY SURROUND P.DIRECT 4. To return the NORMAL mode, press the SET SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/

AUTO dts INPUT

LIP SYNC/ INPUT AUTO dts SYSTEM REMOTE CONTROLLER RC5500SR Notes: button. 123 3. Press ENTER button to continue erasing.

2. Press and hold down the SET and MENU buttons until LEARN indicator blinks. • When the SEND indicator blinks once again, the transmitting code is unavailable for remote controller, or the transmitting signal is intercepted Erasing the code by SOURCE 1. Press and hold down the SET and MENU buttons until LEARN indicator blinks. • The SEND indicator blinks twice and the mode returns to LEARN mode. • To cancel the erasing operation, do not SOURCE SET l/ MULTI/ CAT OFF ON by noise. M-SPKR • If no buttons are pressed for approximately 1 press ENTER button and simply touch any

SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ INFO MENU minutes while in the LEARN mode, the remote SOURCE l/ MULTI/ CAT SET OFF ON M-SPKR other button.

AUTO dts INPUT controller automatically exits from the LEARN SLEEP DISPLAY SURROUND INFO MENU

123 ENTER mode. P.DIRECT LIP SYNC/ INFO MENU

AUTO dts INPUT

3. Select the SOURCE button to select the 123 ENTER ENTER

SOURCE. BASS TREBLE TV DSS 2. Press and hold down the SLEEP button and T.TONE EXIT /SET UP press the learned SOURCE button twice to be DVD VCR 4. To return the NORMAL mode, press the SET

TUNER CD CDR MD erased. • LEARN indicator lights. button.

TAPE AUX1 AUX2 AMP CH-SEL V-OFF ATT.

REMOTE CONTROLLER SOURCE l/ SET OFF ON BASS TREBLE TV DSS Note:

DVD VCR SLEEP DISPLAY SURROUND P.DIRECT

AUTO TUNER LIP SYNC/ dts INPUT CD CDR MD Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory

AUX1 123 TAPE AMP AUX2 preset code.

17

EN GL CONNECTIONS Surround left and right speakers When this unit is used in surround operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the CONNECTING SPEAKERS Surround

IS H SPEAKER PLACEMENT listening position. Passive subwoofer Power Amplifi er Powered subwoofer BACK Right Left

The ideal surround speaker system for this unit is 7- The center of the center speaker should face the INVERT INPUT INPUT OUTPUT LEVEL BTL REMOTE CONT. EXT. CONT. IN MASTER SLAVE or

center of the room. MIN MAX IN

speaker systems, using front left and right speakers, a center speaker, surround left and right speakers, a surround back left and right speakers, and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units. This will deliver smooth pans across the front sound stage as the action moves from side to side. Your center channel speaker is very important as Surround back left and right speakers Surround back speakers are required when a full 7.1- channel system is installed. Speakers should be placed on a rear wall, behind the listening position. The center of the center speaker should face the center of the room. Subwoofer FM (75) GND AM ANTENNA ANTENNA SYSTEM OUT OUT FUSE SPEAKER SYSTEM MINIMUM 4 OHMS VIDEO S-VIDEO S-VIDEO VIDEO/ +5~13V DC INPUT 1 1 INPUT COMPONENT COMPONENT HDMI Ver 1.1 HDMI Ver 1.1 INPUT VIDEO 3 MONITOR MONITOR OUT 2

2 INPUT 3 INPUT 3 OUTPUT

over 80% of the dialog from a typical motion picture emanates from the center channel. It should possess similar sonic characteristics to the L SL C SBL We recommend using a sub-woofer to have maximum L bass effect. As the subwoofer only handles low R TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR IN 4 5 1 2 3 INPUT 1 INPUT 1 INPUT 2 INPUT 2

frequencies, you can place it any where in the room. R SR SW SBR MULTI. IN OUT IN OUT IN OUT OPT OUT FLASHER FLASHER

main speakers. Surround channel speakers need not (AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT INDC

be identical to the front channel speakers, but they should be of high quality. HEIGHT OF THE SPEAKER UNITS OUT RS-232C RS-232C SPEAKER C SPEAKER C OFF ON L SL SBL C TV DVD VCR TAPE DSS AUDIO R CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. TRIGGER TRIGGER AC IN

The surround back speaker is useful for playback of Dolby Digital Surround EX or DTS-ES. One of R Front left and right speakers, and a center speaker Align the tweeters and mid-range drivers on the L R L L L L R L L L R R R R FRONT B FRONT A MODEL NO. SR5002 MODEL NO. SR5002

the benefi ts of both Dolby Digital and DTS is that FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER SURROUND SURROUND CENTER AC OUTLET AC OUTLET

R SR SW SBR SW FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS 230V 50/60Hz 230V 50/60Hz

surround channels are discrete full range, while they were frequency limited in earlier “Pro Logic’ type systems. Bass effects are an important part of home theater. For optimal enjoyment a subwoofer should be used as it is optimized for low frequency reproduction. If you have full range front speakers, however, they may be used in place of a subwoofer with proper setting of the switches in the menu system. Surround Left Subwoofer three front speakers at the same height, as best as possible. Surround left and right speakers, and surround back speaker Place the surround left, right and surround back speakers higher than your ears by about 70cm – 1m. Also place the speakers at the same height, as best as possible. PRE OUT PRE OUT PRE OUT PRE OUT Right Left SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS Right Left SYSTEMS SYSTEMS SYSTEMS SYSTEMS Right SWITCHED SWITCHED 0.65A 150W 0.65A 150W Center Left Surround Back Left Front Left Front Center 0° 70cm 1m Front B SR5002 only CONNECTING SPEAKER WIRE Front A Surround 1. 2.

Surround Back Right 150° 135° Surround Right 22° 30° Front Right 1. Strip away approx. 3/8 inch (10 mm) of wire insulation. 2. Twist the bared wire ends tight, to prevent short circuits. 10 mm 3. 4. 5.

90° 110° Front left and right speakers We recommend to set the front L and R speakers with 45-60 degrees from the listening position. Center speaker Align the front line of the center speaker with the front L/R speakers. Or place the center speaker a little backward from the line. Note: Use magnetically-shielded speakers for front left, right and the center speakers when the speakers are installed near the TV. 3. Loosen the knob by turning it counterclockwise. 4. Insert the bare part of the wire into the hole in side of each terminal. 5. Tighten the knob by turning it clockwise to secure the wire.

18

Caution: • Be sure to use speakers with the specifi ed impedance as shown on the rear panel of this unit. • To prevent damage to circuitry, do not let the bare CONNECTING AUDIO COMPONENTS H S I CD recorder CD player Tape Deck L G

speaker wires touch each other and do not let them touch any metal part of this unit. • Do not touch the speaker terminals DIGITAL DIGITAL OUTPUT DIGITAL OUT IN N L L E R R OUT IN

when the power is on. It may cause you to receive an electric shocks. INPUT OUTPUT L R L R L R L R Analog Audio L R R L • Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit. Note: Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the FM (75) GND AM ANTENNA ANTENNA VIDEO S-VIDEO S-VIDEO R L L R INPUT 1 1 INPUT INPUT 3 MONITOR MONITOR OUT 2 COMPONENT COMPONENT VIDEO R L Digital Audio (coaxial)

L SL C SBL signal phase will be reversed and the signal quality L will be corrupted. R 2 TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR IN OUT Y CB/PB CR/PR Y CB/PB CR/PR IN 4 5 4 5 1 2 3 Digital Audio (optical)

R SR SW SBR MULTI. IN OUT IN OUT IN OUT IN OUT OPT OPT OUT FLASHER

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT IN

OUT TV DVD VCR TAPE

CONNECTING A SUBWOOFER DSS RS-232C RS-232C SPEAKER C SPEAKER C OFF ON L SL SBL C TAPE AUDIO CD/CDR CD/CDR DIGITAL IN DIGITAL IN DIGITAL OUT DIGITAL OUT REMOTE CONT. REMOTE CONT.

R Use the PRE OUT SUBWOOFER jack to connect a L R L L L R R

powered subwoofer (power amplifi er built in). FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER AC OUTLE AC OUTLET

R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER 230V 50/60 230V 50/60Hz

If your subwoofer is a passive type (power amplifi er is not built in), connect a monaural power amplifi er to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifi er. PRE OUT PRE OUT SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS R L R L SYSTEMS SYSTEMS SWITCHED SWITCHED 0.65A 150W 0.65A 150W

The output audio signal from the TAPE OUT jack and the CD/CD-R OUT jack is the same signal which is currently selected. Caution: Do not connect this unit and other components to mains power until all connections between components have been completed. Notes: • Insert all plugs and connectors securely. Incomplete connections may make noise. • Be sure to connect the left and right channels properly. Red connectors are for the R (right) channel, and white connectors are for the L (left) channel. • Be sure to connect input and output properly. • Refer to the instructions for each component that is connected to this unit. • Do not bind audio/video connection cables with power cords and speaker cables this will result in generating a hum or other noise. CONNECTING DIGITAL AUDIO COMPONENTS • There are 4 digital inputs (SR4002), 5 digital inputs (SR5002), 2 coaxial jacks and 2 optical jacks (SR4002), 3 optical jacks (SR5002), on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components. • There is one optical output jack on the rear panel. These jacks can be connected to a CD recorder, or a MD deck inputs, respectively. • Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source’s connected to digital input jacks. • Use fiber optical cables (optical) for DIG-1,2 (SR4002), DIG-1,2,3 (SR5002), input jacks. Use 75 ohms coaxial cables (for digital audio or video) for DIG-3,4 (SR4002), DIG-4,5 (SR5002), input jacks. • You can designate the input for each digital input/ output jacks according to your component. See page 27. Notes: • There is no Dolby Digital RF input jack. Please use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the video disc player to the digital input jack. • The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly. • Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively.

19 CONNECTING VIDEO COMPONENTS VIDEO, S-VIDEO , COMPONENT JACKS E N There are 3 types of video jacks on the rear panel. G

L DVD player VIDEO PROJECTOR I S H AUDIO Satellite Tuner VIDEO jack The video signal for the VIDEO jacks is the conventional composite video signal. S-VIDEO jack The video signal is separated into luminance (Y) and

DIGITAL OUT VIDEO COMPONENT COMPONENT S-VIDEO OUTDIGITAL VIDEO OUT S-VIDEO

AUDIO OUT L R L R OUT S-VIDEO OUT VIDEO IN VIDEO OUT Y CB /PB CR /PR Y CB /PB CR /PR INPUT INPUT IN L R L R R L OUT OUT color (C) signals for the S-VIDEO jack. The S-VIDEO signals enables high-quality color reproduction. If your video component has an S-VIDEO output, we recommend to use it. Connect the S-VIDEO output jack on your video component to the S-VIDEO input jack on this unit. Component jack Make component video connections to a TV or monitor with component inputs to produce higher quality video images. Use a component video cable or 3 video cords to connect the component video out jacks on the unit to the monitor.

VIDEO COMPONENT COMPONENT

FM (75) GND AM ANTENNA ANTENNA VIDEO S-VIDEO S-VIDEO S-VIDEO S-VIDEO 1 1 INPUT 1 INPUT 3 MONITOR MONITOR OUT 2 COMPONENT COMPONENT VIDEO VIDEO FM (75) GND AM VIDEO VIDEO S-VIDEO S-VIDEO INPUT 1 1 INPUT 3 COMPONENT VIDEO Notes:

2 TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR DVD VCR IN VCR OUT VCR OUT MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR ANTENNA ANTENNA INPUT 2 TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y • Be sure to connect the left and right audio channels

L SL C SBL L R R SR SW SBR MULTI. IN OUT IN OUT IN OUT 4 5 1 1 2 3 IN OUT OPT IN OUT L R FLASHER L SL C SBL R SR SW SBR TV MULTI. DSS MONITOR OUT MONITOR OUT IN OUT IN OUT 4 5 1 2 3 2 IN OUT properly. Red connectors are for the R (right) channel, and white connectors are the for L (left) channel.

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT IN OUT TV DVD VCR TAPE DVD VCR DIGITAL IN DIGITAL IN

RS-232C RS-232C SPEAKER C SPEAKER C OFF ON L SL SBL C DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. (AUX2) 7.1CH INPUT 7.1CH INPUT RS-232C RS-232C SPEAKER C SPEAKER C OFF ON L SL SBL C OUT TV DVD VCR TAPE TV DSS DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN DIGITAL IN DIGITAL IN • Be sure to connect the inputs and outputs of the video signals properly.

R L R L L L R R R L R L L L R R • This unit has the “TV-AUTO ON/OFF” function to turn the TV ON or OFF automatically, by sensing

FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER AC OUTLE AC OUTLET FRONT B FRONT A SURROUND BACK SURROUND BACK SURROUND SURROUND CENTER the incoming video signal from the VIDEO jacks.

R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER 230V 50/60 230V 50/60Hz FRONT A OR B.CENTER. FRONT A OR B.CENTER. SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER

SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER

PRE OUT PRE OUT L R L R R L Video SWITCHED SWITCHED 0.65A 150W 0.65A 150W PRE OUT PRE OUT L R SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS Video SYSTEMS SYSTEMS • You may need to setup the digital audio output format of your DVD player, or other digital source components. Refer to the instructions of the each component connected to the digital input jacks. • There is no Dolby Digital RF input jack. Use an external RF demodulator with a Dolby Digital L R L R S-VIDEO Analog Audio R L L R OUTS-VIDEO S-VIDEO Analog Audio R L decoder to connect the Dolby Digital RF output jack of the DVD player to the digital input jack on this unit. • The COMPONENT OUTPUT 1 and 2 terminals of the SR5002 can output the same video signal. • For details concerning the connection of Video equipment, please see VIDEO CONVERT (page

S-VIDEO OUT IN AUDIO OUTAUDIO IN VIDEO OUT IN Digital Audio (coaxial) VIDEO AUDIO OUT IN VIDEO IN Digital Audio (coaxial) 34).

L R VCR L R Digital Audio (optical) L R TV Digital Audio (optical)

20

CONNECTING HDMI COMPONENTS HDMI JACK This unit has 3 HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. Select an input source from the OSD menu system. (See page 27) Notes: • When multiple components are connected to this unit, turn power to unused components off to prevent interference between them. • Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables. • Some DVD-Audio disks disable downmixing. These types of disks are not played back correctly unless the left, center, right and surround left and right speakers, and subwoofer are connected. • If a DVD player that does not support HDMI 1.1 is INPUT DVD player VIDEO PROJECTOR H S I L G HDMI OUTPUT HDMI INPUT N E COMPONENT COMPONENT HDMI Ver 1.1 HDMI Ver 1.1

• When the HDMI output is connected to a display monitor that does not support HDCP*, signals are 1 VIDEO connected to the unit, multi channel PCM playback is not possible even with DVD-Audio disks. INPUT 3 MONITOR MONITOR HDMI Ver 1.1 HDMI Ver 1.1 VIDEO

FM (75) GND AM ANTENNA S-VIDEO 1 OUT 2 INPUT

2 INPUT 3 INPUT 3 OUTPUT INPUT 1 INPUT 1 INPUT 2 INPUT 2

not output. To view images in HDMI, it is necessary • If a DVD player or other device with DVI output is Y CB/PB CR/PR Y CB/PB CR/PR INPUT 1 INPUT 1 INPUT 2 INPUT 2 OUTPUT

L SL C SBL TV DVD VCRIN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR IN

to connect to a display that supports HDCP*. • There may be no image output if connected to a TV or display that is not compatible with the above connected to the unit, a separate audio cable (optical L digital, coaxial digital or analog) is needed for the R audio signals. In this case, select the connected audio IN OUT 4 5 1 2 3 IN OUT

R SR SW SBR MULTI. IN OUT OPT OUT FLASHER FLASHER

INDC input as explained in “1 INPUT SETUP”. (See page (AUX2) 7.1CH INPUT DIGITAL OUT DIGITAL OUT

format. • Refer to the instruction manual of the TV or display 27) OUT RS-232C SPEAKER C OFF ON TV DVD VCR TAPE DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. TRIGGER TRIGGER

to be connected to the unit for detailed information regarding the HDMI terminal. * HDCP: High-bandwidth Digital Content Protection • Multi channel PCM signals and audio signals of 64 L SL SBL C kHz or higher that are input from the HDMI jack are R not output from the DIGITAL OUT jacks. • Depending on the quiality of the cable used, the AC IN L R L L L R R MODEL NO. SR5002 MODEL NO. SR5002

FRONT B FRONT A FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER AC OUTLET AC OUTLET

R SR SW SBR FRONT A + B : 8 OHMS SPEAKER SPEAKER

CONNECTING HDMI COMPONENTS HDMI signal may be affected by noise. PRE OUT • Audio units that use sampling frequencies of 128 kHz and above are not supported. SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS 230V 50/60Hz 230V 50/60Hz SWITCHED SWITCHED 0.65A 150W 0.65A 150W

An HDMI cable (sold separately) is used to connect the HDMI jack on the unit with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack. HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an HDMI-DVI conversion cable or plug. When connecting to a DVI terminal, connect the audio signal separately. Notes: • Some HDMI components can be controlled over the HDMI cable, but this unit cannot control other components this way. • When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output. • DVI cables come with 24-pin and 29-pin plugs. This unit supports 24-pin DVI-D cables; 29-pin DVI cables cannot connect to it. • Some source devices such as DVD players does not support HDMI repeater like those of the unit. In such case, pictures are not properly projected on monitors such as TVs and projectors. • When only HDMI components are connected, OSD will not be displayed. (See page 26) Satellite Tuner HDMI OUTPUT

21

EN G L IS ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS

H INPUT 1 INPUT INPUT 3 MONITOR MONITOR 1 OUT 2 COMPONENT COMPONENT VIDEO 2 INPUT 1 INPUT 1

2 DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR IN IN 4 5 1 2 3 RC OUT

IN OUT IN OUT IN OUT OPT OUT OUT FLASHER FLASHER OPTION

R L R L R L R L R L R L R L R L R L DVD VCR TAPE DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN DIGITAL OUT DIGITAL OUT REMOTE CONT. REMOTE CONT. REMOTE CONT. REMOTE CONT. INDC TRIGGER TRIGGER AC IN

VIDEO CENTER L R L L L R R CENTER

L FM (75) GND AM S-VIDEO S-VIDEO FRONT B FRONT A FRONT A OR B.CENTER. B.CENTER. SURROUND BACK SURROUND BACK SURROUND SURROUND CENTER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER AC OUTLET AC OUTLET 1

ANTENNA ANTENNA FRONT A + B : 8 OHMS : 8 OHMS SPEAKER SPEAKER 230V 50/60Hz 230V 50/60Hz

R FRONT SURR. SURR. BACK SUB WOOFER L L R R L SL C SBL L SL C SBL R SR SW SBR R SR SW SBR (AUX2) 7.1CH INPUT 7.1CH INPUT (AUX2) 7.1CH INPUT 7.1CH INPUT MULTI. OUT TV DVD VCR IN IN TV DVD VCR L R FRONT SURR. SURR. BACK SUB WOOFER SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS SWITCHED SWITCHED 0.65A 150W 0.65A 150W

RS-232C RS-232C SPEAKER C SPEAKER C Power CD recorder CD player DVD player

DVD Audio player or OFF ON L SL SBL L SL SBL C C R SR R L FRONT B FRONT A OR B.CENTER FRONT A OR B.CENTER. Amplifer Subwoofer REMOTE CONTROL IN OUT REMOTE CONTROL IN OUT REMOTE CONTROL IN OUT

R SR SW SBR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL

Super Audio CD Multi channel player L R Center Front Left PRE OUT PRE OUT PRE OUT PRE OUT L R L R Front Right

Surround Left Surround Back Left Surround Right Surround Back Right q You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the unit, be sure to always disable operation of the infrared sensor on the unit by using the following procedure. 1. Hold down the 7.1CH INPUT (SR4002) / MULTI

CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 31. CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifi ers. Be sure to connect each speaker to the corresponding external power amplifi er. this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifi er (some models excluded) is connected to one of these terminals, the power amplifi er’s, power switch is synchronized with this unit’s power switch. Set the REMOTE CONTROL SWITCH on the back of other units (not the SR4002/SR5002) to “EXT”.(EXTERNAL) to use this feature. (SR5002) button and MENU button on the front panel at the same time for fi ve seconds. 2. The setting “IR=ENABLE” is shown on the FL DISPLAY. 3. Press the 1 or 2 cursor button to change this to “IR=DISABLE”. 4. Press the ENTER button. Once this setting is made, the infrared sensor on the unit is disabled. Note: Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to “IR=ENABLE”.

22

CONNECTING THE ANTENNA TERMINALS AM Loop Antenna AM External CONNECTING THE SUPPLIED ANTENNAS Connecting the supplied FM antenna The supplied FM antenna is for indoor use only. H SI

Antenna FM External Antenna FM Antenna L During use, extend the antenna and move it in various G directions until the clearest signal is received. N E Fix it with push pins or similar implements in the position that will cause the least amount of distortion. If you experience poor reception quality, an outdoor antenna may improve the quality. Connecting the supplied AM loop antenna The supplied AM loop antenna is for indoor use only.

FM (75) GND AM FM (75) GND AM ANTENNA ANTENNA ANTENNA ANTENNA VIDEO S-VIDEO S-VIDEO INPUT 1 INPUT INPUT 3 1 COMPONENT COMPONENT HDMI Ver 1.1 HDMI Ver 1.1 VIDEO MONITOR MONITOR OUT 2 Set it in the direction and position it to where you receive the clearest sound. Put it as far away as possible from the unit, televisions, speaker cables,

2 INPUT 3 INPUT 3 OUTPUT

L SL C SBL L R TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR IN 4 5 1 2 3 INPUT 1 INPUT 1 INPUT 2 INPUT 2 and power cords. If you experience poor reception quality, an outdoor

R SR SW SBR MULTI. IN OUT IN OUT IN OUT OPT OUT FLASHER FLASHER antenna may improve the quality.

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT INDC

OUT RS-232C RS-232C SPEAKER C SPEAKER C OFF ON L SL SBL C TV DVD VCR TAPE DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. TRIGGER TRIGGER 1. Press and hold down the lever of the AM antenna terminal. AC IN

R L R L L L R R MODEL NO. SR5002 MODEL NO. SR5002 2. Insert the bare wire into the antenna terminal.

FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER AC OUTLET AC OUTLET 3. Release the lever.

R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER 230V 50/60Hz 230V 50/60Hz

PRE OUT PRE OUT ASSEMBLING THE AM LOOP ANTENNA SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS SWITCHED SWITCHED 0.65A 150W 0.65A 150W CONNECTING AN FM OUTDOOR ANTENNA Notes:

1. Release the vinyl tie and take out the connection line. 2. Bend the base part in the reverse direction. 3. Insert the hook at the bottom of the loop part into the slot at the base part. 4. Place the antenna on stable surface. • Keep the antenna away from noise sources (neon signs, busy roads, etc.). • Do not put the antenna close to power lines. Keep it well away from power lines, transformers, etc. • To avoid the risk of lightning and electrical shock, grounding is necessary. CONNECTING AN AM OUTDOOR ANTENNA An outdoor antenna will be more effective if it is stretched horizontally above a window or outside. Notes: • Do not remove the AM loop antenna. • To avoid the risk of lightning and electrical shock, grounding is necessary.

23

CONNECTING FOR THE MULTI ROOM (SR5002 only) E N G L I S H (Multi room speaker B) CONNECTING FOR SPEAKER C USE (SR5002 only) Bi-amp Connection A bi-amp connection is possible with speakers that have two sets of inputs (for treble and bass). This allows you to drive the treble and bass units with separate channel amps, which enables better

FM (75) GND AM ANTENNA ANTENNA VIDEO S-VIDEO S-VIDEO INPUT 1 INPUT INPUT 3 1 RIGHT SPEAKER COMPONENT VIDEO LEFT SPEAKER sound quality. Connect the speakers as shown in the fi gure. Set the SPEAKER C selector switch on the rear panel to ON. Notes: • If incorrectly connected, a protective circuit in the SR5002 will trip and set the SR5002 to standby. (The STANDBY indicator will fl ash.) In such case, recheck the connections between the speakers and the SR5002. • Turn power to the SR5002 off before changing the setting of the SPEAKER C selector switch.

L SL C SBL L L R R 2 TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB 4 5 1 2 3

R SR SW SBR MULTI. MULTI. IN OUT IN OUT IN OUT OPT INPUT

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT OUT

OUT TV DVD VCR TAPE

RS-232C RS-232C SPEAKER C SPEAKER C OFF ON DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN SPEAKER C SPEAKER C OFF ON FM (75) GND AM ANTENNA ANTENNA VIDEO S-VIDEO S-VIDEO 1 INPUT 1 INPUT 3 COMPONENT VIDEO

L SL SBL C R L R L L L R R L SL C SBL 2 TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR I

R L MULTIROOM L R 4 5 1 2 3

FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER R SR SW SBR MULTI. IN OUT IN OUT IN OUT OPT OU

R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER (AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT

PRE OUT PRE OUT SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS MULTIROOM LEFT MULTIROOM RIGHT RS-232C RS-232C SPEAKER C SPEAKER C SPEAKER C SPEAKER C OFF ON OFF ON L SL SBL C OUT TV DVD VCR TAPE DSS AUDIO CD/CDR DIGITAL IN REMOTE

SPEAKER L R SPEAKER R L R L L L R L L R R R FRONT B FRONT A

FRONT A SURROUND BACK SURROUND BACK SURROUND BACK SURROUND BACK SURROUND SURROUND CENTER

AC 230V SWI0.65R SR

FRONT A OR B.CENTER. FRONT A OR B.CENTER. SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS

R L FRONT L R MAIN AMP (For multiroom) PRE OUT PRE OUT Note: SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS

You can use surround back speaker terminals as multi room speaker terminals when you use no surround back speaker. 24 CONNECTING OTHER EQUIPMENT H S I L G a d s N E

FM (75) GND AM ANTENNA ANTENNA VIDEO S-VIDEO S-VIDEO INPUT 1 INPUT INPUT 3 1 COMPONENT COMPONENT HDMI Ver 1.1 HDMI Ver 1.1 VIDEO MONITOR MONITOR OUT 2

2 INPUT 3 INPUT 3 OUTPUT

L SL C SBL L R TV DVD VCR IN VCR OUT VCR OUT DSS MONITOR OUT MONITOR OUT Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR IN 4 5 1 2 3 INPUT 1 INPUT 1 INPUT 2 INPUT 2

R SR SW SBR MULTI. IN OUT IN OUT IN OUT OPT OUT FLASHER FLASHER FLASHER FLASHER INDC

(AUX2) 7.1CH INPUT 7.1CH INPUT DIGITAL OUT DIGITAL OUT INDC

OUT RS-232C RS-232C SPEAKER C SPEAKER C RS-232C RS-232C OFF ON L SL SBL C TV DVD VCR TAPE DSS AUDIO CD/CDR DIGITAL IN DIGITAL IN REMOTE CONT. REMOTE CONT. TRIGGER TRIGGER TRIGGER TRIGGER AC IN

R L R L L L R R MODEL NO. SR5002 MODEL NO. SR5002

FRONT B FRONT A FRONT A OR B.CENTER. FRONT A OR B.CENTER. SURROUND BACK SURROUND BACK SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER SURROUND SURROUND CENTER AC OUTLET AC OUTLET R SR SW SBR FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SPEAKER 230V 50/60Hz 230V 50/60Hz PRE OUT PRE OUT a RS232C SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS SYSTEMS SYSTEMS SWITCHED SWITCHED 0.65A 150W 0.65A 150W

Connect an external control device or other device for servicing. (Use a straight cable for the connection.) s DC OUT (DC TRIGGER) External devices can be controlled from the SR5002 by connecting them to the DC OUT terminal (12 V). (See page 30) d FLASHER IN This unit can be controlled by connecting a control box or other control device to this unit. 25

SETUP E N G After all components are connected, initial setup L I must be performed. S H ON SCREEN DISPLAY MENU SYSTEM This unit incorporates an on-screen menu system, which makes various operations possible by using the cursor (3, 4, 1, 2) and ENTER buttons on the remote control or on the front panel. Note: To view the on-screen displays, make certain you have made a connection from the Monitor Out jack on the rear panel to the composite, S-Video, component video input of your TV or projector. (see page20) 1. Press the AMP button of the remote controller.(This step is not needed when operating the setup menus from the unit itself.) 2. Press the MENU button on the remote controller or set to display the “SETUP MAIN MENU” of the OSD menu system. There are 8 items in the SETUP MAIN MENU. 3. Select a desired sub-menu with the 3 or 4 cursor buttons, and press the ENTER button to enter. The display will change to the selected sub-menu. You can lock the condition of setup AUTO AUTO SETUP START CANCEL 1-1 INPUT SETUP FUNC:MODE :DIG:HDMI:COMP ------------------------ TV :AUTO : 5 : - : - DVD :AUTO : 1 : 1 : 1 VCR :AUTO : 3 : 3 : 3 DSS :AUTO : 2 : 2 : 2 AUX1:AUTO : F : - : - MAIN NEXT EXIT * For the SR4002, “–” is displayed for TV DIG and VCR HDMI. 1-2 INPUT SETUP FUNC:MODE :DIG:HDMI:COMP ------------------------ TAPE:AUTO : - : : CD/R:AUTO : 4 : : AUX2:AUTO : - : : MAIN RETURN EXIT 2-1 SPEAKER SETUP SPEAKER SETUP : AUTO SET MICROPHONE SETUP MAIN MENU 1. INPUT SETUP :UNLOCK 2. SPEAKER SETUP:UNLOCK 3. PREFERENCE :UNLOCK 4. SURROUND :UNLOCK 5. PLIIx MUSIC :UNLOCK 6. CSII :UNLOCK 7. 7.1 CH. INPUT:UNLOCK 8. MULTI ROOM :UNLOCK EXIT * “8. MULTI ROOM” is displayed only with the SR5002. 3 PREFERENCE STANDBY MODE : ECONOMY TV-AUTO : DISABLE OSD INFO : ENABLE BILINGUAL : MAIN VIDEO CONVERT HDMI : ENABLE DC TRIGGER MAIN EXIT * “DC TRIGGER” is displayed only with the SR5002. 3-1 VIDEO CONVERT TV : ON DVD : ON VCR : ON DSS : ON AUX1 : ON 4 SURROUND SURR.MODE :AUTO HT-EQ :OFF LFE LEVEL : MAIN EXIT 5 PLIIx MUSIC PARAMETER PARAMETER : DEFAULT PANORAMA : OFF DEMENSION : 0 CENTER WIDTH : 3 MAIN EXIT 6 CSII PARAMETER TRUBASS : 0 SRS DIALOG : 0 to each sub-menu with the 1 or 2 or cursor buttons. Note: If you desire to adjust any sub-menu, you need to set it to UNLOCKED. 4. If you desire to exit from this menu system, press the EXIT button, or move the cursor to EXIT and press the ENTER button. When only HDMI components are connected, the OSD menu will not be displayed on the screen. SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN NEXT EXIT 2-3 SPEAKERS DISTANCE DISTANCE UNIT : ft FRONT L : 10.0 ft FRONT R : 10.0 ft CENTER : 10.0 ft SURR.L : 10.0 ft SURR.R : 10.0 ft SUB W : 10.0 ft SURR.B L : 10.0 ft SURR.B R : 10.0 ft MAIN RETURN NEXT EXIT MAIN NEXT EXIT MANUAL 2-2 SPEAKERS SIZE SUBWOOFER : YES FRONT L/R : LARGE CENTER : SMALL SURROUND L/R : SMALL SURR.BACK : 2CH SURR.BACK SIZE : SMALL LPF/HPF : 100Hz BASS MIX : BOTH MAIN NEXT EXIT 2-3 SPEAKERS DISTANCE DISTANCE UNIT : m FRONT L : 3.0 m FRONT R : 3.0 m CENTER : 3.0 m SURR.L : 3.0 m SURR.R : 3.0 m SUB W : 3.0 m SURR.B L : 3.0 m SURR.B R : 3.0 m MAIN RETURN NEXT EXIT MAIN RETURN EXIT SR5002 only 3-2 DC TIRGGER SETUP DC TRIG DISABLE TV : TAPE : DVD : CD/R : VCR : AUX2 : DSS : TUNER: AUX1 : 7.1CH: MAIN RETURN EXIT 2-4 SPEAKERS LEVEL TEST MODE : MANUAL FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN RETURN EXIT MAIN EXIT 7 7.1 CH. INPUT LEVEL VIDEO-IN : LAST FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN EXIT SR5002 only 8 MULTI ROOM AUDIO : DVD SLEEP TIMER : OFF MULTI:OUT : STEREO MULTI:OFF MSPK : VOL : VARI LEVEL : -90dB --- MAIN ROOM STATUS --- VIDEO:DVD AUDIO:DVD MAIN EXIT

26

1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND COMPONENT VIDEO INPUT) Use this menu to select the input jack to be assigned to the input source. 1. Select “INPUT SETUP” in SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 1-1 INPUT SETUP FUNC:MODE :DIG:HDMI:COMP ------------------------ TV :AUTO : 5 : - : - DVD :AUTO : 1 : 1 : 1 VCR :AUTO : 3 : 3 : 3 DSS :AUTO : 2 : 2 : 2 AUX1:AUTO : F : - : - MAIN NEXT EXIT * For the SR4002, “–” is displayed for TV DIG and VCR HDMI. 1-2 INPUT SETUP FUNC:MODE :DIG:HDMI:COMP ------------------------ TAPE:AUTO : - : : CD/R:AUTO : 4 : : AUX2:AUTO : - : : MAIN RETURN EXIT 2. To select the input source and MODE, press the 3 or 4 cursor buttons. 3. To select “DIG” “HDMI” or “COMP” for the input jack, press the 1 or 2 cursor buttons. Select “AUTO” for input sources, for automatic detection of the digital input signal condition. If there is not a digital signal present, but there is an analog signal present, the analog signal will be played. Select “DIG”, when only a digital signal will be used. Select “ANA” for input sources for which no digital input jacks are used. 4. To select the vdieo source, select “HDMI” or “COMP” by pressing the 3 or 4 cursor buttons, and press the 1 or 2 cursor buttons to select the vdieo source to be assigned . 5. After you complete this portion of the set up, move the cursor to MAIN with the 3 or 4 cursor buttons and press the ENTER button. Notes: • When the TUNER is fi xed to the analog input, you can not select any digital input. • When a DTS-LD or DTS-CD is playing, this setup is not available. This is to avoid noise being generated from the analog input. • If “AUTO” is selected and a DVD, compact disc or LD is fast-forwarded during playback, decoded signals may produce a skipping sound. In such cases, change the setting to “DIG”. 2 SPEAKER SETUP After you have installed the unit, connected all the components, and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout. Before you perform the following settings, it is important that you first determine the following characteristics: 1. Select “SPEAKER SETUP” in SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 2-1 SPEAKER SETUP Speakers are set up by selecting either MANUAL or AUTO using the 1 and 2 cursor buttons. For operation when AUTO has been selected, see MRAC on page 29. 2-1 SPEAKER SETUP SPEAKER SETUP : MANUAL MAIN NEXT EXIT 2-2 SPEAKERS SIZE When setting the speaker size in the SPEAKER SIZE sub-menu, use the guidelines given below. LARGE: The complete frequency range for the channel you are setting will be output from the speaker. SMALL: Frequencies of the channel you are setting lower than approx. 100 Hz will be output from the subwoofer. If the Subwoofer is set to “NONE”, the setting of the front speakers will be fi xed to “LARGE,” and the sound will be output from both the left and right speakers. 2-2 SPEAKERS SIZE SUBWOOFER : YES FRONT L/R : LARGE CENTER : SMALL SURROUND L/R : SMALL SURR.BACK : 2CH SURR.BACK SIZE : SMALL LPF/HPF : 100Hz BASS MIX : BOTH MAIN NEXT EXIT 1. To select the each speaker, press the 3 or 4 H cursor buttons. S I 2. To select the setting of each speaker size, L press the 1 or 2 cursor buttons. G N 3. After you complete this portion of the set up, E move the cursor to “NEXT” with the 3 or 4 cursor buttons and then press the ENTER button to go to the next page. SUBWOOFER: YES: Select when a subwoofer is connected. NONE: Select when a subwoofer is not connected. FRONT L/R LARGE: Select if the front speakers are large. SMALL: Select if the front speakers are small. • If “NONE” is selected for the Subwoofer setting, then this setting is fi xed to “LARGE.” CENTER NONE: Select if no center speaker is connected. LARGE: Select if the center speaker is large. SMALL: Select if the center speaker is small. SURROUND L/R NONE: Select if no surround left and right speakers are connected. LARGE: Select if the surround left and right speakers are large. SMALL: Select if the surround left and right speakers are small. SURR. BACK NONE: Select if no surround back left and right speakers are connected. 2CH: Select if the surround back left and right speakers are connected. 1CH: Select if the one surround back speaker is connected. In this case, the audio signal is emitted form the Surround back L output terminal.

27

Notes: E • If “NONE” is selected for the Surround L/R setting, N then this setting is fi xed to “NONE.” G L • You can use surround back speaker terminals as I S multi room speaker terminals when you use no H surround back speaker. (See page 22) SURR. BACK SIZE LARGE: Select if the surround back speaker is large. SMALL: Select if the surround back speaker is small. Note: If “NONE” is selected for the Surround L/R setting, then this setting is not available. LPF/HPF When you use a subwoofer, you can select the cutoff frequency for the small speakers used. Select one of the crossover frequency levels according to the size of the small speaker connected. 80Hz → 100Hz → 120Hz → 150Hz → 180Hz Notes: • If using small front speakers, set a slightly higher frequency. If using large front speakers, set a slightly lower frequency. • If Pure-Direct mode, 7.1CH Input is in use, this function does not take effect. BASS MIX • The bass mix setting is only valid when “LARGE” is set for the front speakers and “YES” is set for the subwoofer during stereo playback . This setting has effect only during playback of PCM or analog stereo sources. • When “BOTH” is selected, the low frequencies will be played through the main L&R, as well as the sub woofer. In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range. • By selecting “MIX”, the low frequencies will play through the main L&R ONLY. Note: LFE signals during playback of Dolby Digital or DTS, will be played through the sub woofer. 2-3 SPEAKERS DISTANCE Use this parameter to specify the distance of each speaker’s position from the listening position. The delay time is automatically calculated according to these distances. Begin by determining the ideal or most commonly used seating position in the room. This is important for the timing of the acoustics to create the proper sound space that the unit and today’s sound systems are able to produce. Note: For speakers that you have selected “NONE” the Speaker Configuration sub-menu will not appear here. (There are several useful books and special DVD and LD’s available to guide you through proper home theater confi guration. If you are unsure, have your Marantz dealer perform the installation for you. They are trained professionals familiar with even the most sophisticated custom installations. Marantz recommends the CEDIA.ORG website for further information about this). 2-3 SPEAKERS DISTANCE DISTANCE UNIT : m FRONT L : 3.0 m FRONT R : 3.0 m CENTER : 3.0 m SURR.L : 3.0 m SURR.R : 3.0 m SUB W : 3.0 m SURR.B L : 3.0 m SURR.B R : 3.0 m MAIN RETURN NEXT EXIT 1. To select each speaker , press the 3 or 4 cursor buttons. 2. To set the distance for each speaker , press the 1 or 2 cursor buttons. 3. After you complete this portion of the set up, move the cursor to “NEXT” with the 3 or 4 cursor buttons and then press the ENTER button to go to the next page. FRONT L: Set the distance from the front left speaker to your normal listening position. CENTER: Set the distance from the center speaker to your normal listening position. FRONT R: Set the distance from the front right speaker to your normal listening position. SURR. L: Set the distance from the surround left speaker to your normal listening position. SURR. R: Set the distance from the surround right speaker to your normal listening position. SUB W: Set the distance from the subwoofer to your normal listening position. SURR. B L: Set the distance from the surround back left speaker to your normal listening position. SURR. B R: Set the distance from the surround back right speaker to your normal listening position. Notes: • Set the distance to each speaker in meters (m) or feet (ft) as follows. m: 0.1 - 9 m in 0.1 m steps ft: 0.3 - 30 ft in 0.3 ft steps • For the speakers that you have selected “NONE” the Speaker Size menu will not appear. • The setting for Surr.Back L and Surr.Back R appears if you set for it to, two surround back speakers in the Speaker Size menu. • The setting of Surr.Back appears if it is set for one surround back speaker in the Speaker Size menu. 2-4. SPEAKERS LEVEL SETTING WITH TEST TONE Here you will set the volume for each speaker so that they are all heard by the listener at the same level. We recommend using a SPL (Sound Pressure Level) meter, when available. Note: The speaker level settings are not available in 7.1 Channel Input mode, CS mode and Multi Channel Stereo mode. 2-4 SPEAKERS LEVEL TEST MODE : MANUAL FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN RETURN EXIT TEST MODE : Selects “MANUAL” or “AUTO” for generating the mode of the test tone with the 1 or 2 cursor buttons. If you select “AUTO” , the test tone will be cycled through in a circular pattern which is Left → Center → Right → Surround Right → Surround Back Right → Surround Back Left → Surround Left → Subwoofer → Left → .. increments of 2 seconds for each channel. Using the 1 or 2 cursor buttons, adjust the volume level of the noise from the speaker so that it is the same level for all the speakers. If you select “MANUAL”, adjust the output level of each speaker as listed below. 1. When you move the cursor to FRONT L by pressing the 4 cursor button, the unit will emit a pink noise from the front left speaker. Remember the level of this noise and then press the 4 cursor button. (Note that this can be adjusted to any level between -10 and +10 dB in 1 dB intervals except the subwoofer setting. The subwoofer can be adjusted to any level between -15 and +10 dB in 1 dB intervals.) The unit will now emit the pink noise from the center speaker. 2. Using the 1 and 2 cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker. 3. Press the 4 cursor button again. The unit will now emit the pink noise from the front right speaker. 4. Repeat steps 2 and 3 above for the front right and other speakers until all speakers are adjusted to the same volume level. After you complete this portion of the set up, press the ENTER button, the cursor will move to “MAIN” and then press the ENTER button to go to SETUP MAIN MENU. Notes: • Speakers that you selected “NONE” for in the Speaker Size menu will not appear. • The setting of Surr.Back L and Surr.Back R appears if you have set it for two surround back speakers in the Speaker Size menu. • The setting of Surr.Back appears if you have set it for one surround back speaker in the Speaker Size menu. • To adjust the speaker levels for 7.1-channel input sources, you will need to use the 7.1CH-INPUT sub menu. (See page 31).

28

MRAC (Marantz Room Acoustic Calibration) Speaker settings that were diffi cult by MANUAL setup can now be made by automatically measuring speaker characteristics using the including microphone. Measurement During measurement, a test tone is output from the speakers, which is then measured and analyzed though the microphone. The measurement fl ow and items are as follows. • About surround back speakers : When the surround back speaker is set to NONE in H the SPEAKER SETUP, it is skipped in the AUTO S I setup. To use the surround back speaker, set it to L YES by MANUAL setup before using the MRAC G feature. N

2-1 SPEAKER SETUP SPEAKER SETUP : AUTO SET MICROPHONE MAIN NEXT EXIT AUTO SETUP START CANCEL SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN EXIT NG AUTO SETUP START CANCEL MIC SETUP ERROR SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN NEXT EXIT Microphone connection check: MIC CHECK Ambient noise measurement: AMBIENT NOISE Speaker connected/not connected check: SPEAKER CHECK Speaker output level check: SPEAKER LEVEL Distance from speaker (delay time) check: SPEAKER DISTANCE Speaker characteristics check: SPEAKER SIZE How to Operate Settings are displayed on the monitor during setup, therefore turn the monitor on. 1. Connect the included microphone to the MRAC jack of the unit. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP E • The MRAC feature is available except in the following modes. - 7.1 CH INPUT - PURE-DIRECT - SOURCE DIRECT 3. Select “2. SPEAKER SETUP” on the SETUP MAIN MENU, then select AUTO for “2- 1 SPEAKER SETUP”. Move the cursor to “NEXT” with the 3 or 4 cursor buttons and then press the ENTER button. 2-1 SPEAKER SETUP SPEAKER SETUP : AUTO SET MICROPHONE

AUTO SETUP AUTO SETUP PURE SIMPLE

SURROUNDDISPLAY MEMORYMUTE ATT MULTI

MULTI STANDBY SPEAKER MODE DIRECT SETUP CLEAR ENTER

START CANCEL AMBIENT NOISE CHK SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN EXIT NG START CANCEL AMBI NOISE ERROR SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN NEXT EXIT AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO MAIN NEXT EXIT 4. Select START on the AUTO SETUP display AUTO SETUP START CANCEL AMBIENT NOISE OK &&&&&&&&&&&&&&&& SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN EXIT AUTO SETUP START CANCEL NOW ANALYZING >&&&&&&&&&&&&&&&& SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN EXIT AUTO SETUP START CANCEL FINISHED SPEAKERS CHECK : OK SPEAKERS LEVEL : OK SPEAKERS DISTANCE : OK SPEAKERS SIZE : OK MAIN RETURN NEXT EXIT NG AUTO SETUP START CANCEL SPEAKER SET ERROR SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN NEXT EXIT 2. Set the microphone at ear height as in the actual listening position. Use a stand or tripod to position the microphone. Notes: • Remove any obstructions between the speakers and the microphone. • Keep the room quiet during measurement. • The test tone emitted during measurement is loud. Take considerations for neighboring homes and children. • Step away from the listening position during measurement and operate the unit with the remote controller from outside the speaker path. and press the ENTER button to start measurements. AUTO SETUP START CANCEL SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE : MAIN RETURN NEXT EXIT 5. For measurement items, see “Measurement”. 6. When measurements are completed, “FINISHED” appears on the monitor. 7. Once finished, disconnect the microphone from the unit. 8. Measurement results can be seen by selecting “NEXT” and press the ENTER button or selecting “2. SPEAKER SETUP” on the SETUP MAIN MENU. Then select MANUAL for “2-1 SPEAKER SETUP”.

29

Notes: E • If MRAC is started with both speaker settings A N and B off, it will enter CANCEL mode without G displaying an ERROR on the screen. When this L I happens, check the SPEAKER setting. S H • The measured speaker distance may differ from the actual distance from speakers. Nevertheless, the measured value is suitable for the speakers. • To make changes to individual speakers, select 2. SPEAKER SETUP on the SETUP MAIN MENU, then select MANUAL for 2-1 SPEAKER SETUP. • The included microphone is designed specifi cally for this receiver. Other microphones do not guarantee suitable measurement results. Use the included microphone to conduct measurements. • During measurement, press the ENTER or EXIT button to cancel measurement. • In some rooms, an error may occur during auto speaker setup or it may not be possible to set Speaker distance correctly because of room acoustics. In such case, set the speaker distance by MANUAL setup. • Please set any THX Certifi ed speakers manually to “Small” and the crossover to “80 Hz” after Auto setup operation. • When only HDMI components are connected, OSD will not be displayed. Error Indications During Measurement If trouble occurs during measurement, an error message is displayed on the monitor screen and FL display. Those errors and their remedies are described below. The message appearing on the FL display is given in ( ). MIC SETUP ERROR (MIC SET ERROR) The microphone (MC-10) is not properly connected. → Check the microphone connection. AMBI NOISE ERROR (AMBI NOISE ER) Measurement cannot be done correctly because of excessive ambient noise. → Either temporarily turn off power to noisy devices such as air conditioning or move them out of the room. → Retry measurement when the room is quiet. SPEAKER SET ERROR (SPK SET ERROR) The speakers are not properly connected. → Recheck speaker layout and connections. 3 PREFERENCE 3 PREFERENCE STANDBY MODE : ECONOMY TV-AUTO : OSD INFO : ENABLE VIDEO CONVERT HDMI : ENABLE DC TRIGGER MAIN EXIT 1. Select “PREFERENCE” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To select a desired content, press the 3 or 4 cursor buttons. STANDBY MODE: When this function is set to “ECONOMY”, you can reduce the power consumption when the unit is in the standby mode. Note: TV-AUTO and RS-232C are disabled in the “ECONOMY” setting (SR5002 only). TV AUTO: Select the TV AUTO ON/OFF function to enable or disable with the 1 or 2 cursor buttons. OSD Info: Select the OSD information function to enable or disable with the 1 or 2 cursor buttons. If you select “ENABLE”, the unit will display the status of the feature (Volume up/down, input select, etc..) on the TV monitor. But if you do not desire this information, select “DISABLE”. VIDEO CONVERT: Select the VIDEO CONVERT function to enable or disable with the 1 or 2 cursor buttons. (Video cable connection: Refer to page 20) 3-1 VIDEO CONVERT TV : ON DVD : ON VCR : ON DSS : ON AUX1 : ON MAIN RETURN EXIT After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button. HDMI AUDIO: This setting determines whether to playback audio input to the HDMI jacks through the unit or output it through the unit to a TV or projector. ENABLE: The audio input to the HDMI jacks can be played back by this unit. In such case, audio signals are not output to the TV or projector. THROUGH: The audio input to the HDMI jacks is not output from the speaker terminals of the unit. Audio data is output directly to the TV or projector. This setting is used to listen to audio on a multi channel TV, etc. DC TRIGGER: Select “DC TRIG SETUP” in the SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 3-2 DC TIRGGER SETUP DC TRIG DISABLE TV : TAPE : DVD : CD/R : VCR : AUX2 : DSS : TUNER: AUX1 : 7.1CH: MAIN RETURN EXIT You can select MAIN ROOM, MULTI ROOM, REMOTE or DISABLE by pressing 1 or 2 cursor buttons. Notes: • REMOTE is available for the external control. The RC5001SR cannot operate this function. • To select desired input source , press 3 or 4 cursor button. • To set ON or OFF, press 1 or 2 cursor button. • After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button. 4 SURROUND 4 SURROUND SURR.MODE :AUTO HT-EQ :OFF LFE LEVEL : MAIN EXIT 1. Select “SURROUND” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To select a desired content , press the 3 or 4 cursor buttons. SURR.MODE: Select the desired surround mode with the 1 or 2 cursor buttons. HT-EQ: Select to active the HT-EQ with the 1 or 2 cursor buttons. The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because fi lm soundtracks were designed to be played back in large movie theater environments. Activating the HT-EQ feature when watching a fi lm made for movie theaters corrects this and restores the correct tonal balance. The HT-EQ feature is available except in the following modes. • 7.1 CH INPUT • PURE-DIRECT • SOURCE DIRECT • When VIRTUAL is set for the surround mode LFE LEVEL: Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0 dB, -10 dB or OFF with the 1 or 2 cursor buttons. After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.

30

5 PL II (PRO LOGIC II) MUSIC PARAMETER Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs. In this mode, SR4002/SR5002 includes three controls to fi ne-tune the soundfi eld as follows. 5 PLIIx MUSIC PARAMETER PARAMETER : DEFAULT PANORAMAA : OFF DIMENSION : 0 CENTER WIDTH : 3 MAIN EXIT Select “PL II MUSIC” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. PARAMETER: Select “DEFAULT” or “CUSTOM” with the 1 or 2 cursor buttons. If you select “CUSTOM”, you can adjust three parameters as listed below. PANORAMA: Select the Panorama mode On or Off with the 1 or 2 cursor buttons. Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective. DIMENSION: Set the Dimension level between +3 and –3 level in 1 level intervals with the 1 or 2 cursor buttons. Adjust the soundfi eld either towards the front or towards the rear. This can be useful to help achieve a more suitable balance from all the speakers with certain recordings. CENTER WIDTH: Set the Center width level between 0 and 7 in 1 level intervals with the 1 or 2 cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers. At its widest setting, all the sound from the center is mixed into the left and right. This control may help achieve a more spacious sound or a better blend for the front image. If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button. 6 CS II (CIRCLE SURROUND II) PARAMETER 6 CSII PARAMETER TRUBASS : 0 SRS DIALOG : 0 MAIN EXIT 1. Select “CS II” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To Select desired contents as below, press the 3 or 4 cursor buttons. TRUBASS: Set the TRUBASS level between 0 and 6 level in 1 level interval with the 1 or 2 cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects. SRS DIALOG: Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the 1 or 2 cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say. If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button. 7 7.1 CH INPUT LEVEL This sub-menu is to adjust the speaker levels for 7.1- channel input sources. Here you will adjust the volume for each channel so that they are all heard by the listener at the same level. 7 7.1 CH. INPUT LEVEL VIDEO-IN : LAST FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN EXIT 1. Select “7.1CH INPUT” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To select “VIDEO IN”, press 3 or 4 cursor button. 3. Using the 1 or 2 cursor buttons, select the video input source which is emitted from Monitor out in the 7.1 CH INPUT function. The input source is switched by pressing the 1 or 2 cursor buttons as follows; LAST ↔ TV ↔ DVD ↔ VCR ↔ DSS ↔ AUX1 ↔ V-OFF ↔ LAST ↔ Notes: • When select LAST, the source is set previous source before 7.1 CH INPUT function is activated. • When select V-OFF, no signal is emitted from monitor out terminal. 4. To Select desired channel , press the 3 or 4 cursor buttons. 5. Using the 1 or 2 cursor buttons, adjust the volume level of each channel. 6. After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button. Notes: • These settings will be memorized to 7.1CH INPUT source. • This feature can be directly selected with the CH.SEL button of the remote controller. 8 MULTI ROOM (SR5002 only) H SR5002 has features in MULTI ROOM SYSTEM S I such as source selector, sleep timer, Multi Room L G Speaker output and remote control. N You can set these feature in this sub-menu. E 8 MULTI ROOM AUDIO : DVD SLEEP TIMER : OFF MULTI:OUT : STEREO MULTI:OFF MSPK : VOL : VARI LEVEL : -90dB --- MAIN ROOM STATUS --- VIDEO:DVD AUDIO:DVD MAIN RETURN EXIT 1. Select “MULTI ROOM” in the SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 2. To Select desired contents, press 3 or 4 cursor button AUDIO: Select the audio source of the Multi-room output with 1 or 2 cursor buttons. SLEEP TIMER: SLEEP timer function is available during the multiroom is active, set the time with 1 or 2 cursor buttons. MULTI OUT: To switch MULTI and MSPK outputs to either STEREO or MONO, press 1 or 2 cursor button. MULTI (MULTI ROOM): To switch on the Multi-room output ON or OFF, press 1 or 2 cursor button. VOL (VOLUME SETUP): Select whether the Multi-room output level is variable or fi xed with a 1 or 2 cursor buttons. LEVEL (VOLUME LEVEL): Adjust the Multi-room output level with 1 or 2 cursor buttons. MSPK (MULTI SPEAKER): To switch on the Multi-speaker output ON or OFF, press 1 or 2 cursor buttons. Note: This setting can be changed when the Surr Back is set “NONE” in 2-1 SPEAKER SIZE menu. When this setting is unavailable, “✽✽✽” is displayed MAIN ROOM STATUS: Selected input source in the main room will be displayed. Note: If “VOLUME” is set to “FIXED”, the multi-room output level cannot be adjusted from the second zone. After you complete this portion of the set up, move the cursor to “MAIN” with 3 or 4 cursor buttons and

press ENTER button. 31

EN G SIMPLE SETUP The relation of the speakers number and conectted speaker

You can setup the speaker conditions quickly with L I SIMPLE SETUP menu. In this menu, the number S CHANNELFront L/R (F) Front Center (C) Surround L/R (S) Surround Back L/R (SB) Sub woofer (SW)

H of speakers and speaker delay time can be set. These settings can be changed more detail in “2. SPEAKER” setup menu. Press the SIMPLE SETUP button on the unit to enter this menu. 1. 2. 4. 3. 5. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP 7.1 ch LARGE SMALL SMALL 2ch YES 7.0 ch LARGE SMALL SMALL 2ch NONE 6.1 ch LARGE SMALL SMALL 1ch YES 6.0 ch LARGE SMALL SMALL 1ch NONE 5.1 ch LARGE SMALL SMALL NONE YES 5.0 ch LARGE SMALL SMALL NONE NONE 4.1 ch LARGE NONE SMALL NONE YES 4.0 ch LARGE NONE SMALL NONE NONE 3.1 ch LARGE SMALL NONE NONE YES 3.0 ch LARGE SMALL NONE NONE NONE

MULTI STANDBY MULTI SPEAKER SURROUND MODE PURE DIRECT SIMPLE SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT 2.1 ch LARGE NONE NONE NONE YES 2.0 ch LARGE NONE NONE NONE NONE

AUTO HT-EQ MENU EXIT BAND T-MODE SETUP MIC POWER ON/OFF PHONES AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO The relation of the room size and fl oor space SIZE Floor spaceWidth 1. Press the SIMPLE SETUP button on the unit to enter the “SPEAKERS” menu. 2. Press 1 or 2 cursor button to select the speaker (W) Depth (D) Imaging Distance Front (F) 6 ft. (1.8 m) Center (C) 5 ft. (1.5 m)

number. 3. Press the 4 cursor button to enter the “ROOM” menu. 4. Press 1 or 2 cursor button to select the room size. 5. After fi nishing all setup, press the 4 cursor button to exit the SIMPLE SETUP menu. Note: All Simple Setup menu is reset when the speaker setting is changed with Speaker Setup menu. SIMPLE SETUP SMALL 10 m2 2.7 m 3.6 m MEDIUM 16 m2 3.6 m 4.5 m LARGE 24 m2 4.5 m 5.4 m Surround (S) 4 ft. (1.2 m) Surr. Back (SB) 5 ft. (1.5 m) Sub Woofer (SW) 5 ft. (1.5 m) Front (F) 7 ft. (2.1 m) Center (C) 6 ft. (1.8 m) Surround (S) 5 ft. (1.5 m) Surr. Back (SB) 7 ft. (2.1 m) Sub Woofer (SW) 6 ft. (1.8 m) Front (F) 9 ft. (2.7 m) Center (C) 8 ft. (2.4 m) Surround (S) 7 ft. (2.1 m) Surr. Back (SB) 8 ft. (2.4 m) Sub Woofer (SW) 8 ft. (2.4 m)

1.SPEAKERS : ? 2.ROOM : ? MAIN RETURN EXIT The relation of the room size and fl oor space is a roughly standard.

32

BASIC OPERATION (PLAYBACK) SELECTING THE SURROUND MODE Example: AUTO SURROUND ADJUSTING THE MAIN VOLUME 7.1CH IN A/D HT-EQ 0 +10 TEMPORARILY TURNING OFF THE SOUND H SI L

VOLUME CL MEMO CAT 7.1CH IN A/D HT-EQ G

INPUT SELECTOR AV SURROUND RECEIVER SR5002 SOURCE l/ SET OFF ON DOWN UP CH/ SPKR A/B MUTE VOLUME VOLUME 0 +10 CL MEMO N

SELECTING AN INPUT SOURCE SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ SPLAY MEMORY CAT MULTI/ CLEAR CAT CH/ M-SPKR DOWN UP SPKR A/B MUTE VOLUME E

AUTO dts INPUT MUTE ATT

Before you can listen to any input media, you must fi rst select the input source on the unit. SURROUND PURE SIMPLE 123 CS EX/ES VIRTUAL EXIT BAND T.MODE T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO INFO MENU ISPLAY MEMORY MUTE ATT CAT MULTI/ CLEAR M-SPKR

MULTI STANDBY MULTI SPEAKER MODE DIRECT SETUP 456 EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO INFO MENU

Example : DVD POWER ON/OFF PHONES SETUP MIC AUTO HT-EQ MENU M-CH ST STEREO NIGHT 789 P.SCAN ENTER

7.1CH IN A/D ENTER Adjust the volume to a comfortable level using HT-EQ

AV SURROUND RECEIVER SR5002 INPUT SELECTOR DISC+ ANGLE SUB TITLE AUDIO CL 0 +10 MEMO the VOLUME control knob on the front panel or To temporarily silence all speaker outputs such as

SURROUND PURE CH-SEL V-OFF ATT. BASS TREBLE TV DVD VCR DSS SIMPLE To select the surround mode during playback, press the SURROUND MODE button on the front panel or the SURROUND MODE buttons on the remote VOLUME 3 / 4 buttons on the remote controller. To increase the volume, turn the VOLUME knob clockwise or press VOLUME 3 button on the when interrupted by a phone call, press the MUTE button on the front panel or MUTE button on the remote controller.

MULTI STANDBY MULTI SPEAKER MODE DIRECT SETUP TUNER CD CDR MD controller. remote controller, to decrease the volume, turn This will interrupt the output to all speakers and the

AUTO HT-EQ MENU SETUP MIC TAPE POWER ON/OFF PHONES AUX1 AUX2 AMP counterclockwise or press VOLUME 4 button on the head-phone jack, but it will not affect any recording or

REMOTE CONTROLLER To select DVD, turn the INPUT SOURCE knob on the front panel or simply press the DVD button on the NIGHT MODE AUTO dts remote controller. Notes: • The volume can be adjusted within the range of – ∞ to 18 dB, in steps of 1 dB. LIP SYNC/ INPUT dubbing that may be in progress. When the system is muted, the display will show “MUTE” . Press the MUTE button again to return to normal operation.

remote controller. After you have selected DVD, simply turn on the DVD player and play the DVD. 123 CS EX/ES VIRTUAL 456 M-CH ST STEREO NIGHT 789 T.MODE P.SCAN • However, when the channel level is set as described on page 26, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. USING THE SLEEP TIMER

7.1CH IN A/D (In this case the maximum volume adjustment range is HT-EQ

• As the input source is changed, the new input 0 +10 CL MEMO CAT “18 dB - Maximum value of channel level)

name will appear momentarily an OSD information on the video display. The input name will also SPKR A/B CH/ MUTE VOLUME SEND LEARN

appear in the display, on the front-panel. • As the input is changed, this unit will automatically switch to the digital input, surround mode, attenuation, and night mode status which were Press the NIGHT button on the remote controller to turn on the NIGHT mode. Selecting the Night Mode ON is effective in Dolby Digital only, and it compresses the dynamic range. ADJUSTING THE TONE (BASS & TREBLE) CONTROL - PRESET + - TUNING + SOURCE l/ SLEEP SET OFF ON P.DIRECT DISPLAY SURROUND LIP SYNC/

INPUT AUTO dts This softens loud passages such as sudden

entered during the confi guration process for that source. • When an audio source is selected, the last video explosions, to help prevent disturbing others late at night. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. 123 CS EX/ES VIRTUAL 456 T.MODE

input used remains routed to the VCR Output and Monitor Output. This permits simultaneous To turn off the Night mode, press the NIGHT button again. BASS TREBLE TV DSS To program this unit for automatic standby, press the SLEEP button on the remote controller.

DVD VCR

viewing and listening to different sources. TUNER CD CDR MD Each press of the button will increase the time before

AUX1 AUX2 AMP TAPE • When a Video source is selected, the video shut down in the following sequence.

signal for that input will be routed to the Monitor Output jacks and will be viewable on a TV monitor connected to the unit. If a component video input is connected to the DVD or DSS component inputs, it will be routed to the Component Video Output. Make certain that your TV is set to the proper input to view the signal. REMOTE CONTROLLER During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics. (Using the remote controller) To adjust the bass effect, press BASS 3 or BASS 4 on the remote controller. To adjust the treble effect, press TREBLE 3 or TREBLE 4 on the remote controller. Note: The tone control function can work in the AUTO Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and Multi Ch. Stereo mode. OFF 10 20 30 50 40 120 90 80 70 60 110 100 The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed. When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows “SLEEP OFF” and the SLEEP indicator will disappear. 33

VIDEO CONVERT E N When this function is activated, the video or G Example: Monitor is connected with the component. HDMI AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP L S-video signal can be emitted from the video, S-video SR5002 only SURROUND PURE SIMPLE MODE MULTI DIRECT SETUP CLEAR MULTI SPEAKER STANDBY ENTER DISPLAY MEMORY MUTE ATT

I S or component video output terminal. H To activate this function, select VIDEO CONVERT in AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP POWER ON/OFF SETUP MIC PHONES HDMI AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO VIDEO

SURROUND PURE SIMPLE MULTI MODE DIRECT SETUP DISPLAY MEMORY CLEAR MULTI SPEAKER MUTE ATT STANDBY ENTER PREFERENCE menu and set ENABLE. S-VIDEO

Notes: POWER ON/OFF PHONES SETUP MIC AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO component

• The component video signal is emitted only from component video output terminal. VIDEO component Monitor is connected with the video or S-video. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP

MULTI STANDBY MULTI SPEAKER SURROUND MODE PURE DIRECT SIMPLE SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT

When the video equipment is connected by component terminal, connect the monitor and SR4002/SR5002 by the component terminal. SR5002 only AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME POWER ON/OFF SETUP MIC PHONES VIDEO AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO

DOWN UP SURROUND PURE SIMPLE MODE MULTI DIRECT SETUP DISPLAY MEMORY CLEAR MULTI SPEAKER MUTE ATT • This function is unavailable for the REC out STANDBY ENTER S-VIDEO HDMI component

terminal. POWER ON/OFF SETUP MIC PHONES AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO

• This function is unavailable for the still picture, fast forward and reverse playing of the video component. • If, while attempting to use the video convert feature, the SR4002/SR5002 cannot synchronize with the display device, “NO SIGNAL” appears on the monitor, or noise is generated, this feature cannot be used. All of these signs are caused by equipment VIDEO S-VIDEO Monitor is connected with the video or component. SR4002/SR5002 AV SURROUND RECEIVER SR4002 INPUT SELECTOR VOLUME DOWN UP Notes of OSD menu: HDMI: OSD menu is not displayed. VIDEO/S-VIDEO/component: VIDEO CONVERT of HDMI is not possible, thus the OSD menu is not displayed.

incompatibility; there is nothing wrong with the SURROUND PURE SIMPLE DIRECT SETUP DISPLAY MEMORY CLEAR MODE 7.1 CH INPUT S.SPEAKER B MUTE ATT STANDBY ENTER

SR4002/SR5002. POWER ON/OFF SETUP MIC PHONES AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO

In such case, set VIDEO CONVERT in the PREFERENCE menu to DISABLE. Also, connect the video input signal to the display device via the MONITOR OUT terminal under VIDEO and the S-video input signal to the display device via the MONITOR OUT terminal under S-VIDEO. S-VIDEO VIDEO component SR4002/SR5002 AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP

MULTI STANDBY MULTI SPEAKER SURROUND MODE PURE DIRECT SIMPLE SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT

POWER ON/OFF SETUP MIC PHONES AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO VIDEO

component S-VIDEO The signal cannot be converted from the component to the video or S-video. Notes of OSD menu: • The setup menu can be displayed through all video out (COMPONENT, S-VIDEO, VIDEO). • The setting informations (e.g. volume setting) are displayed through all video out when the VIDEO CONVERT function are set ON. Note: No setting information is displayed when the signal is emitted from the COMPONENT IN to COMPONENT OUT. • The setting informations (e.g. volume setting) are displayed through the S-VIDEO or VIDEO out when the VIDEO CONVERT function are set DISABLE. When the S-VIDEO and VIDEO outputs are used simultaneously, the setting informations are displayed through the S-VIDEO out only. 34 SURROUND MODE H S I This unit is equipped with many surround modes. These are provided to reproduce a variety of surround sound effects, according to the content of the source to be played. L The available surround modes may be restricted depending on the input signal and speaker setup. G N E The relation between the selected surround mode and the input signal The surround mode is selected with the surround mode selector on this unit or the remote controller. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That relationship is as follows;

Mode Input Signal Decoding Output Channel Front information display Mode Input Signal Decoding Output Channel Front information display

Surround L/R C SL SRSBL SBR SubW Signal format indicators Channel status Surround L/R C SL SRSBL SBR SubW Signal format indicators Channel status

AUTO Dolby Surr. EX Dolby Digital EX OOOOO 2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO - O 2 DIGITAL L, C, R, SL, SR, LFE Dolby D(2ch) Dolby Digital 2.0 O ---- 2 DIGITAL L, R Dolby D (2ch Surr) Pro Logic IIx movie OOOOO 2 DIGITAL , 2 SURROUND L, R, S DTS-ES DTS-ES OOOOO dts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOO - O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE Multi Ch-PCM Multi Ch-PCM OOO - O PCM L, C, R, SL, SR, LFE Multi Ch-PCM 96kHz Multi Ch-PCM 96kHz OOO - O PCM L, C, R, SL, SR, LFE PCM(Audio) PCM (Stereo) O --- O PCM L, R PCM 96kHz PCM (96kHz Stereo) O --- O PCM L, R HDCD PCM (Stereo) O --- O PCM HDCD L, R Analog Stereo O --- O ANALOG - STEREO Dolby Surr. EX Stereo O --- O 2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Stereo O --- O 2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Stereo O --- O* 2 DIGITAL L, R Dolby D (2ch Surr) Stereo O --- O* 2DIGITAL , 2 SURROUND L, R, S DTS-ES Stereo O --- O dts, ES L, C, R, SL, SR, S, LFE DTS 96/24 Stereo O --- O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) Stereo O --- O dts L, C, R, SL, SR, LFE Multi Ch-PCM Stereo O --- O PCM L, C, R, SL, SR, LFE PCM (Audio) Stereo O --- O PCM L, R PCM 96kHz Stereo O --- O PCM L, R HDCD PCM (Stereo) O --- O PCM HDCD L, R Analog Stereo O --- O ANALOG - Virtual Dolby Surr. EX Virtual O ---- 2 DIGITAL EX L, C, R, SL, SR, S, LFE

SOURCE DIRECT PURE DIRECT Dolby Surr. EX Dolby Digital EX OOOOO 2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO - O 2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Dolby Digital 2.0 O ---- 2 DIGITAL L, R Dolby D (2ch Surr) Pro Logic IIx movie OOO - - 2 DIGITAL , 2 SURROUND L, R, S DTS-ES DTS-ES OOOOO dts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOO - O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE Multi Ch-PCM Multi Ch-PCM OOO - O PCM L, C, R, SL, SR, LFE Multi Ch-PCM 96kHz Multi Ch-PCM 96kHz OOO - O PCM L, C, R, SL, SR, LFE PCM (Audio) PCM (Stereo) O - - - - PCM L, R PCM 96kHz PCM (96kHz Stereo) O - - - - PCM L, R HDCD PCM (Stereo) O - - - - PCM HDCD L, R Analog Stereo O - - - - ANALOG - Dolby D (5.1ch) Virtual O ---- 2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Virtual O ---- 2 DIGITAL L, R Dolby D (2ch Surr) Virtual O ---- 2 DIGITAL , 2 SURROUND L, R, S DTS-ES Virtual O ---- dts, ES L, C, R, SL, SR, S, LFE DTS (5.1ch) Virtual O ---- dts L, C, R, SL, SR, LFE Multi Ch-PCM Virtual O - - - - PCM L, C, R, SL, SR, LFE PCM (Audio) Virtual O - - - - PCM L, R Analog Virtual O ---- ANALOG - Multi Ch. StereoDolby Surr. EX Dolby Digital EX OOOOO 2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO - O 2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Multi Channel Stereo O O O O O* 2 DIGITAL L, R Dolby D (2ch Surr) Multi Channel Stereo O O O O O* 2 DIGITAL , 2 SURROUND DTS-ES DTS-ES OOOOO dts, ES L, C, R, SL, SR, S, LFE

EX/ES Dolby Surr. EX Dolby Digital EX OOOOO 2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital EX OOOOO 2 DIGITAL L, C, R, SL, SR, LFE DTS-ES DTS-ES OOOOO dts , ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS-ES OOOOO dts 96/24 L, C, R, SL, SR, LFE DTS(5.1ch) DTS-ES OOOOO dts L, C, R, SL, SR, LFE Multi CH-PCM Multi Ch-PCM + Dolby EX OOOOO PCM L, C, R, SL, SR, LFE AAC (5.1ch) AAC EX OOO - O AAC L, C, R, SL, SR, LFE DTS 96/24 DTS 96/24 OOOOO dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE Multi Ch-PCM Multi Ch-PCM OOO - O PCM L, C, R, SL, SR, LFE Multi Ch-PCM 96kHz Multi Ch-PCM 96kHz OOO - O PCM L, C, R, SL, SR, LFE PCM (Audio) Multi Channel Stereo O O O O O* PCM L, R Analog Multi Channel Stereo O O O O O* ANALOG -

DOLBY (PL IIx movie) (PL IIx music) (PL IIx game) (Pro Logic) Dolby Surr. EX Dolby Digital 5.1 OOO * O 2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO * O 2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Pro Logic IIx OOOOO 2 DIGITAL L, R Dolby D (2ch Surr) Pro Logic IIx OOOOO 2 DIGITAL , 2 SURROUND L, R, S Multi Ch-PCM Multi Ch-PCM + PLIIx OOOOO PCM L, C, R, SL, SR, LFE PCM (Audio) Pro Logic IIx OOOOO PCM L, R * : Depending on the particular setup, there may be differences compared to the information contained in these tables. O* : When L/R (FRONT Speaker) = SMALL.

DTS (Neo:6 Cinema) (Neo:6 Music) CS II Cinema CS II Music CS II Mono Analog Pro Logic IIx OOOOO ANALOG - DTS-ES DTS 5.1 OOO - O dts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOO - O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE PCM (Audio) Neo:6 OOOOO PCM L, R Analog Neo:6 OOOOO ANALOG - Dolby D (2ch) Neo:6 OOOOO 2 DIGITAL L, R Dolby D (2ch Surr) Neo:6 OOOOO 2 DIGITAL , 2 SURROUND L, R, S PCM (Audio) CS II OOOOO PCM L, R Analog CS II OOOOO ANALOG - Dolby D (2ch) CS II OOOOO 2 DIGITAL L, R Dolby D (2ch Surr) CS II OOOOO 2 DIGITAL , 2 SURROUND L, R, S Notes: • Dolby Digital (2 ch: Lt/Rt): signal with Dolby Surround fl ag Speakers are full set. • No sound outputs from the surround speaker, center speaker and subwoofer if the DVD disc has no surround data. Abbreviations L/R : Front speakers C : Center speaker SL/SR : Surround speakers SBL/SBR : Surround Back speakers SubW : Sub woofer speaker

35

AUTO E N When this mode is selected, the unit determines G whether the digital input signal is Dolby Digital, Dolby L Digital Surround EX, DTS, DTS-ES, DTS 96/24 or I S PCM-audio. H Surround EX & DTS-ES will operate for multichannel source that has a Dolby Digital Surround EX or DTS ES auto trigger fl ag in the digital signal. When a Dolby Digital or DTS signal is input, the number of channels for which the corresponding signal is encoded will be played. Inputting a Dolby Digital two channel signal with Dolby surround status automatically subjects that signal to Pro Logic IIx movie processing before play. PCM 96 kHz source material can be played in this mode. Notes: • When you use this mode with certain DVD and CD players, performing operations such as “Skip” or “Stop” may momentarily interrupt the output. • When the signal is not decoded, the mode is changed to AUTO mode automatically. Refer to page 35 to confi rm the available decoding mode. SOURCE DIRECT In the Source Direct mode, the tone control circuit and bass management confi guration are bypassed for full-range frequency response and the purist audio reproduction. Notes: • Speaker size is set to Front L/R = LARGE, Center = LARGE, Surround L/R = LARGE and Subwoofer = YES automatically. Tone controls, equalizer and additional processing are deactivated. • When you use this mode with certain DVD and CD players, performing operations such as skip or stop may momentarily interrupt the output. PURE DIRECT The Pure Direct mode further reduces sources of noise in addition to effect of the Source Direct mode, by blocking output from the video jacks (VIDEO, S-VIDEO, COMPONENT VIDEO and HDMI) and turning the FL display off. EX/ES This mode provides 6.1 channel surround for DOLBY DIGITAL EX, DTS-ES encoded source material such as DVD. This mode cannot be used when an analog input has been selected. Dolby Digital EX In a movie theater, fi lm soundtracks that have been encoded with Dolby Digital surround EX technology are able to reproduce an extra channel which has been added during the mixing of the program. This channel, called Surround Back, places sounds behind the listener in addition to the currently available front left, front center, front right, surround right, surround left and subwoofer channels. This additional channel provides the opportunity for more detailed imaging behind the listener and brings more depth, spacious ambience and sound localization than ever before. Dolby Digital EX is not available in the system without surround back speaker(s). DTS-ES (Discrete 6.1, Matrix 6.1) DTS-ES adds the surround back channel audio to the DTS 5.1-channel format to improve the acoustic positioning and makes acoustic image movement more natural with the 6.1-channel reproduction. This unit incorporates a DTS-ES decoder, which can handle DTS-ES Discrete-encoded and DTS-ES Matrix-encoded program sources from DVD, etc.. DTS-ES Discrete 6.1 features digital discrete recording of all channels including the surround back channel(s) and higher quality of audio reproduction. DTS-ES is not available in the system without a surround back speaker. 2 MODE (Dolby Digital, Pro Logic IIx MOVIE, Pro Logic IIx MUSIC, Pro Logic IIx GAME, Pro Logic) This mode is used with source materials encoded in Dolby Digital and Dolby Surround. DOLBY DIGITAL This mode is enabled when playing source materials encoded in Dolby Digital. Playing multichannel encoded 6.1 or 7.1-channel Dolby Digital sources provides five main audio channels (left, center, right, surround left and surround right) and Low Frequency Effect channel. Dolby Digital EX decoding is not available in this mode. Dolby Pro Logic IIx brings the excitement of surround sound to any stereo mix, while making existing Dolby Surround mixes sound more like discrete 5.1 channels Surround sound. Dolby Pro Logic IIx has 3 modes. Please see below. Pro Logic IIx MOVIE This mode provides 6.1 or 7.1 channel surround sound from Dolby Surround encoded stereo movie sound tracks. Pro Logic IIx MUSIC This mode provides 6.1 or 7.1 channel surround sound from conventional stereo sources, analog or digital, such as CD, Tape, FM, TV, Stereo VCR, etc. Pro Logic IIx GAME Game mode restores the impact low-frequency surround effects by routing them to the system’s subwoofer. Pro Logic This mode emulated original Dolby Pro Logic decoding (3/1 surround) suit for Dolby Surround encoded stereo movie soundtracks. Notes: • Pro Logic IIx mode will decode as Pro Logic II mode when the SURROUND BACK SPEAKER is set NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27) • Pro Logic IIx mode is available for a 2ch input signal which is encoded in Dolby Digital or PCM format. • PCM-audio signals can be subjected to Pro Logic processing when the sampling frequency is 32 kHz, 44.1 kHz or 48 kHz. dts MODE (dts, Neo:6 Cinema, Neo:6 Music) This mode is for DTS encoded source materials such as LASER DISC, CD, and DVD. Neo:6 is for some 2 channel sources. dts : This mode is enabled when playing source materials encoded in dts multichannel. Playing multichannel encoded 5.1-channel dts sources provides five main audio channels (left, center, right, surround left and surround right) and Low Frequency Effect channel. dts-ES decoding is not available in this mode. The DTS mode cannot be used when an analog input has been selected. Neo:6 Cinema, Neo:6 Music This mode decodes 2-channel signals into 6- channel signals using high-accuracy digital matrix technology. The DTS NEO:6 decoder has near-discrete properties in the frequency characteristics of the channels as well as in channel separation. According to the signals to be played back, DTS NEO:6 uses either the NEO:6 CINEMA mode optimized for movie playback or the NEO:6 MUSIC mode optimized for music playback. Notes: • Neo:6 mode is available to 2ch input signals which are encoded in Dolby Digital or PCM Analog format. • PCM-audio signals can be subjected to Neo:6 processing when the sampling frequency is 32 kHz, 44.1 kHz or 48 kHz.

36

CIRCLE SURROUND II (CSII-CINEMA, CSII-MUSIC, CSII-MONO) Circle Surround is designed to enable multichannel surround sound playback of non-encoded and multichannel encoded material. Backward compatibility provides listeners with up to 6.1 channels of surround performance from entire collection of music and fi lm, including broadcast, videotape and stereo recorded music. Depending on source material, you can select CSII Cinema mode, CSII-Music mode or CSII-Mono mode. CSII Cinema mode This mode is suited for playing back Circle Surround encoded and non-encoded film and television soundtracks. Cinema Mode enables 6.1-channel surround playback of 2-channel sources such as Video Cassettes, TV broadcasts, streaming media and DVDs. CSII Music mode This mode is suited for playing back Circle Surround encoded and non-encoded music. Music Mode decodes, music DVDs, radio and TV music broadcasts and CDs into enveloping 6.1-channel surround. CSII-Mono mode This mode plays back monaural recordings from any source, including CDs, DVDs and TV and radio broadcasts in compelling 6.1-channel surround. Notes: • CS II mode is available for 2ch input signals which are encoded in Dolby Digital or PCM format. • PCM-audio signals can be subjected to CS II processing when the sampling frequency is 32 kHz, 44.1 kHz or 48 kHz. STEREO This mode bypasses all surround processing. In stereo program sources, the left and right channels play normally when PCM-audio or analog stereo is input. With Dolby Digital and DTS sources, the 5.1 multichannels are converted to two channel stereo. 96 kHz PCM source material can be played back in stereo mode. VIRTUAL This mode creates a virtualized surround sound experience from a two-speaker (front L and R) playback system playing any multichannel audio source (such as found on DVDs and digital broadcasts), including Dolby Digital, Dolby Pro Logic or DTS. MULTI CH. ST This mode is used to create a wider, deeper and more natural soundstage from two channel source material. This is done by feeding the left channel signal to both left front and left surround speaker and the right channel signal to both right front and right surround speaker. Additionally, the center channel reproduces a mix of the right and left channel. CAUTION H NOTE for DTS signal S I * Connected DVD player, laserdisc player or CD L player needs to support DTS digital output. You G may not be able to play some DTS source signals N from certain CD players and LD players even if E you connect the player to this unit digitally. This is because the digital signal has been processed (such as the output level, sampling frequency or frequency response), and this unit cannot recognize the signal as DTS data. * You can not listen to DTS-encoded software in a multiroom. * Depending on the player used, DTS play may produce a short noise. This is not a malfunction. * While signals from a DTS laserdisc or CD are playing in another surround mode, you cannot switch to digital input or from digital input to analog input from the INPUT SETUP in the MAIN MENU or by pressing the A/D button. * The outputs for VCR 1 OUT, DSS/VCR 2 OUT, TAPE OUT, and CD-R OUT output analog audio signals only. Do not record from CDs or LDs that support DTS using these outputs. If you do, the DTS-encoded signal will be recorded as noise. NOTE for Dolby Digital Surround EX signal * When playing Dolby Digital Surround EX-encoded software in 6.1 channels, it is required to set the EX/ES mode. * Note that some of Dolby Digital Surround EX-encoded software does not contain the identifi cation signal. In this case, set the EX/ES mode manually. NOTE for 96 kHz/192 kHz PCM audio * The AUTO, Pure Direct, and Stereo modes can be used when playing PCM signals with a sampling frequency of 96/192 kHz (such as from DVD Video/Audio discs). * Certain DVD player models inhibit digital output. For details, refer to the player’s operation manual. * Some DVD discs feature copy protection. When using such disc, 96 kHz PCM signal is not output from the DVD player. For details, refer to the player’s operation manual. NOTE for HDCD signal * HDCD is effective only through digital input. * You may not be able to play some HDCD source signals from certain CD players if you connect the player to this unit digitally. This is because the digital signal has been processed (such as the output level, sampling frequency or frequency response) and this unit cannot recognize the signal as HDCD data.

37

EN GL OTHER FUNCTION DISPLAY MODE RECORDING AN ANALOG SOURCE In normal operation, the audio or video source selected for listening through this unit is sent to the Recording the video from one source and the audio from another You can add the sound from one source to the video of another source to make your own video SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT TV DSS

IS DVD VCR recordings.

H ER SR5002 SEND LEARN record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, TUNER Below is an example of recording the sound from TAPE a compact disc player connected to CD IN and the video from a video camera connected to DSS to CD CDR MD AUX1 AMP AUX2 REMOTE CONTROLLER

SOURCE l/ SET OFF ON CD/CDR OUT, VCR OUT in the record mode. video cassette recorder connected to the VCR OUT jack.

SLEEP SURROUND

SURROUND PURE SIMPLE DISPLAY P.DIRECT 456

MODE DIRECT SETUP DISPLAY MEMORY CLEAR AUTO dts LIP SYNC/ INPUT To record the input source signal you are currently

ENTER AUTO HT-EQ MENU EXIT BAND T-MODE 123 CS EX/ES VIRTUAL T.MODE watching or listening to 1. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. M-CH ST STEREO NIGHT 789 P.SCAN

456 A/D 7.1CH IN HT-EQ BASS TREBLE

M-CH ST STEREO NIGHT P.SCAN 1. 2. TV DSS 0 +10 CL MEMO

789 You can select the display mode for the front display - PRESET + - TUNING + TUNER TAPE DVD CD AUX1 VCR CDR MD AUX2 AMP CAT SPKR A/B CH/ MUTE VOLUME

of the unit. AV SURROUND RECEIVER SR5002 INPUT SELECTOR DISC+ ANGLE SUB TITLE AUDIO CAT M-SPKR MULTI/ REMOTE CONTROLLER

To select this mode, press the DISPLAY on the remote controller. CH-SEL V-OFF ATT. TV DSS 1. MULTI BASS TREBLE DVD VCR 1. Switch the video output source to VCR by If you have already assigned the digital inputs, you can temporarily select the audio input mode for each

When this button is pressed, the display mode is SURROUND PURE input source as following procedures. SIMPLE

MULTI MODE SPEAKER DIRECT SETUP TUNER CD CDR MD

switched in the following sequence. STANDBY POWER ON/OFF SETUP MIC PHONES AUTO HT-EQ MENU TAPE AUX1 AUX2 AMP simply pressing the input selector buttons on Press the AMP button and press the A/D (0) button.

→ Surround Mode → Auto-display Off → Display Off → Input Function → Surround Mode.... In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed. In Display off mode, the display is off completely. Note: Only the DISP indicator will be illuminated on the front display in display off condition REMOTE CONTROLLER 1. Select the input source to record by turning the INPUT SOURCE knob on the front panel or simply press the input selector buttons on the remote controller. The input source is now selected and you may watch or listen to it as desired. 2. The currently selected input source signal is output to the TAPE OUT, CD/CDR OUT, VCR OUT outputs for recording. 3. Start recording to the recording component as desired. the remote controller. 2. Switch the audio input source to CD by simply pressing the input selector buttons on the remote controller. 3. Now “CD” has been selected as the audio input source and “VCR” as the video input source. Notes: • If you change the input source during recording, you will record the signals from the newly selected input source. • You cannot record the surround effects. • Digital input signals are only output to the digital outputs. There is no conversion from digital to analog. When connecting CD players and other digital components, do not connect only the digital terminals, but the analog ones as well. When this button is pressed, the input mode is switched in the following sequence. → HDMI Auto → HDMI → Digital → Analog → HDMI Auto.... In HDMI Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. In Digital and HDMI mode, input is fixed to an assigned digital input terminal. In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory. If you need to change the input mode completely, use INPUT SETUP in OSD menu system. (see page 27)

38

LISTENING THROUGH HEADPHONES This jack may be used to listen to the unit’s output DOLBY HEADPHONE MODE This feature simulates the waveforms of the actual ATTENUATION TO ANALOG INPUT SIGNAL 7.1 CH INPUT H This unit is equipped for future expansion through the S

through a pair of headphones. Be certain that the REC sounds heard from the speakers. T.DISP PTY F.DIRECT I use of Multi channel Super Audio CD multichannel L

headphones have a standard 1/4” stereo phono plug. - When headphones are used, the MENU button automatically switches to the Dolby headphone PRESET + - TUNING + G player or DVD-Audio player. N When this is selected, the input signals connected to E Note that the speakers will automatically be turned mode. DISC+ ANGLE AUDIO SUB TITLE the L(front left), R (front right), CENTER, SL (surround off when the headphone jack is in use. The OSD that appears when the MENU button is CH-SEL V-OFF ATT. left), SR (surround right) and SBL (surround back left)

pressed is shown below. AV SURROUND RECEIVER SR5002 BASS TREBLE TV DSS DVD VCR and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and

INPUT SELECTOR TUNER HEAD PHONE CD CDR MD right), center, surround (left and right) and surround

SURROUND PURE DOLBY HP MODE : ON SURROUND : OFF SIMPLE If the selected analog audio input signal is greater than the capable level of internal processing, the back speaker systems as well as the pre-out jacks without passing through the surround circuitry.

MULTI STANDBY MULTI SPEAKER MODE DIRECT SETUP “PEAK” indicator will light up on the front display. If In addition, the signal input to the SW (subwoofer)

AUTO HT-EQ MENU SETUP MIC POWER ON/OFF PHONES Notes: L LEVEL : 0 dB R LEVEL : 0 dB this happens, you should press the ATT button on the remote controller. “ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs. This permits simultaneous viewing with video

• When using headphones, the surround mode will change to BYPASS and Dolby Headphone by MENU and Cursor button. • The surround mode returns to the previous setting as soon as the headphone plug is removed from the jack. • The tone control function can not work through the headphones output. DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons. BYPASS → ON → BYPASS BYPASS: Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo. ON: Dolby headphone mode active. about half. Attenuation will not work with the output signal of TAPE-OUT, CD/CDR-OUT and VCR-OUT. This function is memorized for each individual input source. SPEAKER A/B sources.

When the PURE DIRECT and SOURCE DIRECT mode is selected, Dolby surround processing is M-CH ST STEREO NIGHT 789 P.SCAN

bypassed and “✽✽✽” is displayed as the mode 7.1CH IN A/D HT-EQ

indication. 0 +10 CL MEMO CAT CH/ SPKR A/B The surround mode can be selected when mode is MUTE VOLUME

ON. L/R LEVEL can be set in the ±10 dB range. INFO MULTI/ MENU CAT M-SPKR

Notes: • The surround mode returns to the previous setting as soon as the plug is removed from the jack. • The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input. This unit has speaker system - A and speaker system- B for front L/R channels. You can select these systems by pressing SPEAKERS A/B button on the front panel or SPK AB on the remote controller.

39

EN G L IS 2. 1. INPUT SELECTOR AV SURROUND RECEIVER SR5002 M-CH ST STEREO NIGHT 789 7.1CH IN 2. A/D AUX2 INPUT If you don’t need to connect 7.1 Ch. input terminals P.SCAN with multi channel decoder, HT-EQ TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to VIDEO ON/OFF When no video signal is connected to the unit or a DVD, etc., is connected directly to your TV, the

0 L(front left) and R (front right) inputs terminals are +10 the unit. unnecessary video circuit can be turned off by

H CL MEMO CAT

4. CH/ SPKR A/B MUTE VOLUME available as AUX2 input. selecting the “VIDEO OFF” setting.

SURROUND PURE MULTI/ CAT In this case, You can connect additional audio source M-SPKR AUTO POWER ON To select video off, press the AMP button and press

MULTI MULTI SPEAKER STANDBY MODE DIRECT to AUX2 as other audio input terminals. the V-OFF button.

AUTO HT-EQ POWER ON/OFF SETUP MIC PHONES INFO MENU 1. Be sure the TV auto mode is ENABLED. (Refer TV DSS

ENTER AV SURROUND RECEIVER SR5002 INPUT SELECTOR DVD VCR page 28 : System Setup)

4. T.TONE /SET UP REC EXIT T.DISP PTY F.DIRECT SIMP SURROUND PURE TUNER R5002 2. Connect your TV TUNER (etc) to the TV TAPE VIDEO in terminal. Be sure to connect the CD CDR MD AUX1 AMP AUX2 REMOTE CONTROLLER

- VOLUME PRESET + - TUNING + MULTI STANDBY MULTI SPEAKER MODE DIRECT SETU VIDEO input.

AUTO HT-EQ MEN SURROUND PURE SIMPLE

POWER ON/OFF SETUP MIC PHONES DISC+ ANGLE SUB TITLE AUDIO DIRECT MODE SETUP 3. Turn OFF the power to the TV TUNER and the CLEAR ENTER DISPLAY MEMORY REC T.DISP PTY F.DIRECT

MEMORY CLEAR DOWN UP MUTE ATT 1. CH-SEL V-OFF ATT. BASS TREBLE TV DVD VCR DSS unit. 4. Turn ON the TV TUNER and tune in a receivable AUTO HT-EQ MENU EXIT BAND T-MODE - PRESET + - TUNING +

BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO TUNER CD CDR MD station. DISC+ ANGLE SUB TITLE AUDIO

TAPE AUX1 AUX2 AMP 5. When the station is received, this unit turns ON CH-SEL V-OFF ATT. BASS TREBLE

REMOTE CONTROLLER 1. Select a desired Video source to decide the routed video signal to the Monitor Outputs. HT-EQ (HOME THEATER EQUALIZER) AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME and TV is selected automatically. AUTO POWER OFF TV DVD VCR DSS LIP.SYNC (SR5002 only)

2. Press the 7.1 CH INPUT button on the front SIMPLE PURE SURROUND DIRECT MULTI MODE SETUP panel or press 7.1 CH IN on the remote MULTI SPEAKER STANDBY CLEAR ENTER DOWN DISPLAY MEMORY MUTE 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. Depending on the image device (TV, monitor, projector, etc.) connected to the SR5002, a time lag can occur between image signal processing and

controller to switch the 7.1 channel input. 3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES AUX 1 INPUT DIGITAL S-VIDEO VIDEO L 2. The power to the unit switches to STANDBY after approx. 5 minutes. audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. remote controller. Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between –10 to +10 dB. The subwoofer can be adjusted between –15 and +10 dB. These adjustments result will be stored to 7.1 CH. INPUT memory. 4. Adjust the main volume with the MAIN VOLUME knob or the VOLUME buttons on the remote controller. To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote controller. Notes: • 7.1 CH. Input mode bypasses the internal surround processing, so SURROUND mode cannot be selected. • In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use. At cinemas, the front left, front right and center speakers are located behind the screen. So, screen damping is taken into account when mastering movie software, with an emphasis on high frequencies. When playing back such software at home, the signal takes on different characteristics from those at the cinema. This unit includes HT-EQ to rectify the sound difference between that experienced at a cinema and in a home theater, allowing you to enjoy the same sound you would experience at the cinema at home. The HT-EQ feature is available except in the following modes. • 7.1 CH INPUT • PURE-DIRECT • SOURCE DIRECT • When VIRTUAL is set for the surround mode 1. Press the HT-EQ button on the unit. “EQ” indicator on the front panel will illuminate, indicating the HOME THEATER EQUALIZER has been activated. 2. To cancel this function, press the HT-EQ button again. “EQ” indicator on the front panel will be turned off, indicating the HOME THEATER EQUALIZER has been deactivated. Notes: • AUTO POWER OFF is canceled if this unit is set to a source other than TV. The function reactivates when TV is selected again. • Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. • The S-Video terminal does not support “TV AUTO ON/OFF” function. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the SR5002 to correct the time lag between the sound and image. It can be operated with the “LIP.SYNC” and 1 and 2 cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag. Note: The LIP.SYNC feature turns OFF (0 ms) in the SOURCE DIRECT mode. When the SOURCE DIRECT mode is deactivated, the set value of the LIP. SYNC feature is automatically restored.

40

BASIC OPERATION MANUAL TUNING 2. 1. (FM) TUNING MODE (AUTO STEREO OR MONO) SLEEP DISPLAY SURROUND 2. While pressing the MEMO button, press the 2 H cursor button. S

(TUNER) P.DIRECT LIP SYNC/ VOLUME SOURCE l/ SET OFF ON I “AUTO PRESET” will appear on the display, L

AUTO dts INPUT SLEEP DISPLAY SURROUND P.DIRECT

1. 123 CS EX/ES VIRTUAL BAND T.MODE AUTO dts and scanning starts from the lowest frequency. G LIP SYNC/ INPUT

LISTENING TO THE TUNER 456 M-CH ST STEREO NIGHT 789 P.SCAN CLEAR ENTER DISPLAY MEMORY DOWN UP MUTE ATT 123 CS EX/ES VIRTUAL 456 M-CH ST STEREO NIGHT 3. Each time the tuner fi nds a station, scanning N T.MODE E will pause and the station will be played for fi ve P.SCAN

Frequency scan step for AM is selectable. DOWN EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO 789 seconds.

REC T.DISP PTY F.DIRECT 7.1CH IN A/D HT-EQ During this time, the following operations are

D Default setup is 9 kHz step, if your country’s standard PURE SIMPLE 0 +10

DIRECT SETUP DISPLAY MEMORY M CLEAR 2. CL MEMO CAT

is 10 kHz step, Press BAND button on the remote ENTER HT-EQ MENU EXIT BAND - T-MODE DIGITAL PRESET + - TUNING + SPKR A/B CH/ MUTE VOLUME possible.

controller more than 6 seconds. Scan step will change. Note: Preset memory for the tuner will clear by changing DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE (Using the unit) When in the auto stereo mode, AUTO indicator will be illuminated on the display. The “ST” indicator is illuminated when a stereo broadcast is tuned in. The band can be changed by the BAND button. 4. If no button is pressed during this period, the current station is memorized in location Preset 02. this setup. AUTO TUNING 2. 1. 1. To select tuner and desired band (FM or AM), press the BAND button on the front panel. 2. Press the 3 or 4 cursor buttons on the front panel to select the desired station. SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated. If the signal is weak, it may be diffi cult to tune into the station in stereo. In such a case, press the T-MODE button on the front panel or remote controller. If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues. 5. Operation stops automatically when all 50 preset memory positions are fi lled or when

AUTO dts INPUT (Using the remote controller ) “AUTO” indicator is not illuminated, if FM stereo auto scanning attains the highest end of all

1. DOWN 123 CS EX/ES VIRTUAL 456 M-CH ST STEREO NIGHT 789 BAND T.MODE 1. To select tuner and desired band (FM or P.SCAN AM), press the BAND button on the remote controller. broadcasts are received in monaural and the “ST” indicator is not illuminated. To return to auto stereo mode, press the T-MODE button or press T-MODE button on the remote bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button. Note: REC PURE SIMPLE D T.DISP PTY F.DIRECT 2. Press the 5 or 6 on the remote controller to controller again. AUTO indicator is illuminated on the It is possible that existing preset memory positions

DIRECT SETUP CLEAR ENTER DISPLAY MEMORY M 2. PRESET + - TUNING + - tune in the desired station. display. will be overwritten.

HT-EQ MENU EXIT BAND (Using the unit) T-MODE DIGITAL DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. DIRECT FREQUENCY CALL SLEEP DISPLAY SURROUND P.DIRECT PRESET MEMORY MANUAL PRESET MEMORY 3. 2. 4. SLEEP DISPLAY SURROUND P.DIRECT

SOURCE l/ SET OFF ON LIP SYNC/ LIP SYNC/ With this unit you can preset up to 50 FM/AM stations INPUT AUTO dts

1. To select tuner and desired band (FM or AM), INPUT AUTO dts 1 2 3

press the BAND button on the front panel. SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ 1. 123 CS EX/ES VIRTUAL BAND T.MODE in any order. CEIVER SR5002 3. CS EX/ES VIRTUAL 4 5 6 T.MODE

AUTO dts INPUT 456

2. Press the 3 or 4 cursor buttons on the front 3. 1 2 3 CS EX/ES VIRTUAL T.MODE M-CH ST STEREO NIGHT For each station, you can memorize the frequency P.SCAN M-CH ST STEREO NIGHT 7 8 9 P.SCAN

4 5 6 789 and reception mode if desired. 7.1CH IN A/D HT-EQ

0 A/D +10 7.1CH IN HT-EQ panel for more than 1 second to start the auto

M-CH ST STEREO NIGHT P.SCAN SURROUND 2. SETUP PURE SIMPLE CL MEMO

tuning function. 7 8 9 /SET UP EXIT MODE DIRECT ENTER DISPLAY MEMORY CAT CH/ SPKR A/B MUTE VOLUME

7.1CH IN 0 A/D +10 HT-EQ AUTO PRESET MEMORY AUTO HT-EQ MENU EXIT BAND T

3. Automatic searching begins then stops when a CL MEMO CAT REC 2. T.DISP PTY CAT M-SPKR MULTI/ F.DIRECT

SPKR A/B CH/ VOLUME MUTE station is tuned in. This function automatically scans the FM and AM INFO MENU

MULTI/ CAT M-SPKR - PRESET + - TUNING + band and enters all stations with proper signal

(Using the remote controller) 1. To select tuner and desired band (FM or AM), press the BAND button on the remote controller. 2. Press the 5 or 6 for more than 1 second on 1. To select tuner and desired band (FM or AM), press the BAND button on the remote controller. 2. Press the F.DIRECT on the remote controller, display will show “FREQ - - - -”. strength into the memory. 2. 4. 2. 5. 1. 3. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP (Using the unit) 1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section). 2. Press the MEMORY button on the front panel. “– –“ (preset number) starts blinking on the

the remote controller. 3. Automatic searching begins then stops when a 3. Input your desired station’s frequency with the SIMPLE PURE SURROUND DIRECT MULTI MODE SETUP MULTI SPEAKER numeric buttons on the remote controller. STANDBY CLEAR ENTER DISPLAY MEMORY MUTE ATT display. 3. Select the preset number by pressing the 1

station is tuned in. If tuning does not stop at the desired station, use to AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES 4. The desired station will automatically be tuned. AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO or 2 cursor buttons, while this is still blinking (approx. 5 seconds) the “Manual tuning” operation. 1. To select FM, press the BAND button on the front panel. 4. Press the MEMORY button again to enter. The display stops blinking. The station is now stored in the specifi ed preset memory location.

41

(Using the remote controller) E N 1. Tune into the radio station you desire (Refer to G the “MANUAL TUNING” or “AUTO TUNING” L I section). S H 2. Press the MEMO button on the remote (Using the remote controller) 1. Press the P.SCAN on the remote controller. “PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled fi rst. SORTING PRESET STATIONS AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP 1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station. 2. Press the MEMORY button on the front panel or press the MEMO button on the remote

controller. “– –“ (preset number) starts blinking SIMPLE PURE SURROUND DIRECT MULTI MODE SETUP MULTI SPEAKER 2. Preset stations are recalled in sequence (No.1 STANDBY CLEAR ENTER DISPLAY MEMORY MUTE ATT controller for more than 3 seconds.

on the display. 3. Enter the desired preset number by pressing the numeric buttons. AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES → No.2 → etc.) for 5 seconds each. No stored preset number will be skipped. AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO 3. The left most column of the station name indicator fl ashes, indicating the character entry ready status. Note: When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds. RECALLING A PRESET STATION 1. SLEEP DISPLAY SURROUND P.DIRECT LIP SYNC/ 3. You can fast forward the preset stations by pressing the T continuously. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote controller. CLEARING STORED PRESET STATIONS If you have stations memorized, and there is a gap in the sequential order: I.e. the stations are stored as follows 1) 87.1 MHz 2) 93.1 MHz 3) 94.7 MHz 10) 105.9 MHz (notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press the 4 cursor button while 4. When you press the 3 or 4 cursor buttons on the front panel or the 5 / 6 buttons on the remote controller, alphabetic and numeric characters will be displayed in the following order: A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → + → / → (Blank) → A UP →

AUTO dts INPUT You can remove preset stations from the memory

1. 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 T.MODE P.SCAN using the following procedure. 2. 3. pressing the MEMORY button. “PRESET SORT” will appear on the display and sorting will be done. LIP SYNC/ ← DOWN 5. After selecting the fi rst character to be entered, press the MEMORY or ENTER buttons, press

7.1CH IN A/D HT-EQ AUTO dts INPUT

0 +10 123

SURROUND MODE PURE SIMPLE DIRECT DISPLAY MEMORY CL MEMO CAT 2. CS EX/ES VIRTUAL T.MODE the MEMO button on the remote controller.

SETUP CLEAR ENTER CH/ SPKR A/B MUTE VOLUME VOLUME 456 NAME INPUT OF THE PRESET STATION. The entry in this column is fi xed and the next

AUTO HT-EQ MENU EXIT BAND T-MODE REC 1. T.DISP PTY F.DIRECT M-CH ST STEREO NIGHT 789 P.SCAN column starts to fl ash. Fill the next column the

- PRESET + - TUNING + 7.1CH IN A/D This function allows the name of each preset channel HT-EQ DOWN VIDEO 3. DISPLAY MEMORYMUTE 0 +10 CL MEMO CAT to be entered using alphanumeric characters. same way.

DISC+ ANGLE SUB TITLE AUDIO CH/ CLEAR SPKR A/B MUTE VOLUME

ENTER (Using the unit) 1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO INFO MULTI/ MENU CAT Before name inputting, you need to store preset M-SPKR stations with the preset memory operation. 4. 5. 2. 5. 6. To move back and forth between the characters, press the 1 / 2 cursor buttons or press S or T buttons on the remote controller. Note:

(Using the remote controller) 1. Press the S or T buttons to select the 1. Recall the preset number to be cleared with the method described in “Recalling” a preset station. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP Unused columns should be fi lled by entering blanks. 6. To save the name, press the MEMORY button on the front panel or remote controller for more

desired preset station, or input your desired preset channel with the numeric buttons on 2. Press the MEMORY button on the front panel SIMPLE PURE SURROUND DIRECT MULTI MODE SETUP MULTI SPEAKER or press the MEMO button on the remote STANDBY CLEAR ENTER DISPLAY MEMORY MUTE ATT than 2 seconds.

the remote controller. AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES controller. 3. The stored preset number blinks in the display AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO Ten keypad Press, press again, press again, etc. 1 A → B → C → 1 → A

PRESET SCAN for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote 789 MEMO 2. 5. 6. CH/ 2 D → E → F → 2 → D 3 G → H → I → 3 → G

7.1CH IN A/D HT-EQ

0 +10 CL 1.3. 3.

CS EX/ES VIRTUAL 456 M-CH ST STEREO NIGHT T.MODE controller. CAT VOLUME SPKR A/B MUTE 4. “xx CLEAR” appears on the display to indicate P.SCAN 4 J → K → L → 4 → J 5 M → N → O → 5 → M

789 MULTI/ CAT M-SPKR

7.1CH IN A/D HT-EQ that the specified preset number has been 6 P → Q → R → 6 → P

CL CAT CH/ 0 +10 SPKR A/B MUTE MEMO VOLUME cleared. Note: INFO T.TONE /SET UP ENTER MENU EXIT 7 S → T → U → 7 → S 8 V → W → X → 8 → V 9 Y → Z → space → 9 → Y

REC T.DISP PTY F.DIRECT 3. To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds. REC T.DISP PTY F.DIRECT 0 – → + → / → 0

- PRESET + - TUNING + 5.4. - PRESET + - TUNING +

DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE TV DVD VCR DSS

42

RDS OPERATION Now in use in many countries, RDS (Radio Data System) is a description of the station’s programming hidden space in the FM signal. This unit is equipped with RDS to assist in the selection of FM stations using station and network names, rather than broadcast frequencies. Additional RDS functions include the ability to search for programme types. PROGRAMME TYPE (PTY) DISPLAY The RDS system categorizes programmes according to their genre into different programme type (PTY) groups. To display the programme type information of the current station, press the PTY button in the TUNER MODE on the remote controller. ENTER T.TONE 4. To advance to the next RDS station with the H desired PTY, press the PTY button again within S I 5 seconds. L G NUMBER DISPLAY PROGRAMME TYPE N 1 POP Pop Music E 2 ROCK Rock Music 3 MOR M. O. R. Music 4 LIGHT Light classical 5 CLASSIC Serious classical 6 NEWS News

RADIO TEXT /SET UP REC EXIT T.DISP F.DIRECT PTY 7 AFFAIR Current Affairs 8 INFO Information

Some RDS stations broadcast RADIO TEXT, which is - additional information on the station and programme PRESET + - TUNING + 9 SPORT Sport 10 EDUCATE Education being broadcast. RADIO TEXT information appears as ‘running’ text in the display. RADIO TEXT is transmitted character by the radio station. As a result of that it may take some time until the entire text has been completely received. RDS DISPLAY When this unit is tuned to an FM station that is DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE PTY AUTO SEARCH This unit is equipped to automatically search for stations transmitting any of 29 different programme types. To search for a PTY, follow these procedures: 2. LIP SYNC/ 11 DRAMA Drama 12 CULTURE Culture 13 SCIENCE Science 14 OTHERS Varied 15 OTHER Other Music 16 WEATHER Weather 17 FINANCE Finance 18 CHILDREN Children’s programmes 19 SOCIAL Social Affairs 20 RELIGION Religion 21 PHONE IN Phone In

AUTO dts INPUT

transmitting RDS data, the Front Panel Information Display will automatically show the station name or 5002 RADIO TEXT in place of the typical display of the 2. 1 2 3 CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 T.MODE P.SCAN 22 TRAVEL Travel 23 HOBBIES Hobbies 24 JAZZ Jazz Music

station’s broadcast frequency. 7.1CH IN 0 A/D +10 HT-EQ 25 COUNTRY Country Music

CL MEMO CAT 26 NATION National Music

To change the display, press the T.DISP button on SURROUND CH/ PURE SIMPLE SPKR A/B MUTE VOLUME

DIRECT SETUP MODE the remote controller. CLEAR ENTER DISPLAY MEMORY INFO MENU 27 OLDIES Oldies Music

T.TONE /SET UP AUTO HT-EQ MENU EXIT BAND T-MODE ENTER EXIT 1.3.4. T.TONE /SET UP REC ENTER EXIT T.DISP F.DIRECT PTY 28 FOLK Folk Music 29 DOCUMENT Documentary

REC T.DISP PTY F.DIRECT - PRESET + - TUNING +

PRESET + - TUNING + - DISC+ ANGLE SUB TITLE AUDIO 2. CH-SEL V-OFF ATT. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. PS (Program Service Name) Frequency RT (RADIO TEXT) BASS TREBLE 1. Press the PTY button in the TUNER MODE on the remote controller. The current station’s PTY will be displayed, or the currently selected PTY group will be displayed in blinking if no station or RDS data is present. 2. To change to a new PTY type, press the 3 or 4 cursor button on the front panel or numeric or S / Tbuttons on the remote controller until the desired PTY is shown in the display. 3. Once the desired PTY group or type has been selected, press the PTY button while the display blink (approx. 5 seconds). The PTY Auto search will start, and the tuner will pause at each station broadcasting RDS PTY information corresponding to the selected choice.

43

MULTI ROOM E N SYSTEM (SR5002 only) G L I S H The Multi Room system is a function which allows you to listen to the same or a different source in a room other than the room in which the SR5002 is located. The operations possible with the multi room function are explained briefl y below. For details, refer to the instruction manual supplied MULTI ROOM PLAYBACK USING THE MULTI ROOM OUT TERMINALS The SR5002 is equipped with audio pre-out terminals for which the volume is adjustable as the MULTI output terminals. A separately sold stereo power amplifier can be connected to enjoy multi room playback. 1. 4. 2. 3. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME MULTI ROOM PLAYBACK USING THE MULTI SPEAKER TERMINALS The SR5002 allows you to connect another set of speakers and place them in a different room or separated area for listening to music. 2. 1. 4. 3. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME DOWN UP 1. Press the MULTI SPEAKER (M-SPKR) button. The unit enters multi room speaker mode and the display indicates “SELCT SOURCE” and fl ashes the “MULTI” indicators for approx. 10 seconds. 2. Select the input source using the INPUT SELECTOR knob or function button on the remote controller. Then, the display indicates “MSPKR VOLUME” “MSPKR VOL.–xx” for approx. 5 seconds. 3. During this time, you can set the volume level in with the multi room remote controller and SR5002. SIMPLE PURE SURROUND DIRECT MULTI MODE SETUP MULTI SPEAKER STANDBY DOWN UP CLEAR ENTER DISPLAY MEMORY MUTE ATT the multi room as desired. This will only set the volume in the multi room. When the outputs of the MULTI OUT terminals are SIMPLE PURE SURROUND DIRECT MULTI MODE SETUP MULTI SPEAKER wired and connected to amplifi ers installed in other STANDBY CLEAR ENTER AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES DISPLAY MEMORY MUTE ATT AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO 4. To cancel this function, press the MULTI button on the unit or remote controller (after pressing rooms or M (MULTI) SPEAKER B terminals are wired and connected to L&R speakers in other room, AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO 0 +10 the AMP button on the remote controller).

different sources can be played in rooms other than CL MEMO CAT “MULTI” indicator on the front panel will be

CH/ SPKR A/B MUTE VOLUME 3.

the main room in which the SR5002 and the playback 0 +10 1. 4. MULTI/ CAT M-SPKR turned off.

devices are installed. CL MEMO CAT Notes for MULTI ROOM SPEAKER

CH/ SPKR A/B MUTE VOLUME 3. INFO MENU

SR5002 has some feature to MULTI ROOM SYSTEM as source selector, sleep timer, Multi Room Speaker 1. 4. INFO MULTI/ MENU CAT M-SPKR T.TONE /SET UP ENTER EXIT • MULTI ROOM SPEAKER On/ Off is available in main room only. • MULTI ROOM SPEAKER output terminals can

output and remote control. T.TONE /SET UP ENTER EXIT REC T.DISP PTY F.DIRECT be used when the SURROUND BACK SPEAKER is set NONE in SPEAKER SETUP menu. (See

REC - T.DISP PTY F.DIRECT PRESET + - TUNING + SPEAKER SETUP, page 27)

- PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE • “The Surr. Back Speakers are in use” is displayed by pressing the MULTI SPEAKER (M-SPKR) button when the SURROUND BACK SPEAKER is

DISC+ ANGLE SUB TITLE AUDIO 2. TV DVD VCR DSS set except NONE in SPEAKER SETUP menu. (See

CH-SEL V-OFF ATT. TUNER CD CDR MD 1. 4. SPEAKER SETUP, page 27)

2. BASS TREBLE TV DVD VCR DSS TAPE AUX1 AUX2 AMP

TUNER CD CDR MD 1. 4. REMOTE CONTROLLER

TAPE AUX1 AUX2 AMP

44 REMOTE CONTROLLER 1. Press the MULTI button on the unit or remote controller (after pressing the AMP button on the remote controller). The unit enters MULTI ROOM mode, and the display indicates “SELECT SOURCE.” The “MULTI” indicator will fl ash for about 10 seconds. 2. Select the input source using the INPUT SELECTOR knob or function button on the remote controller. Then, the display indicates “MULTI VOLUME” “MULTI VOL. xx” for approx. 5 seconds. 3. During this time, you can set the volume level in the multi room as desired. This will only set the volume in the second room. 4. To cancel this function, press the MULTI button on the unit or remote controller (after pressing the AMP button on the remote controller). “MULTI” indicator on the front panel will be turned off.

SURROUND SPEAKER B SYSTEM (SR4002 only) The Surround Speaker B system is a function which allows you to listen to the same source in a room other than the room in which the SR4002 is located. The operations possible with the Surround speaker function are explained briefl y below. ANOTHER ROOM PLAYBACK USING THE H S (SURROUND) SPEAKER B TERMINALS S I L The SR4002 allows you to connect another set G of speakers and place them in a another room or N separated area for listening to music. E The SURROUND SPEAKER B system can not be operated with the supplied remote controller. 1. 2. AV SURROUND RECEIVER SR4002 INPUT SELECTOR VOLUME DOWN UP

7.1 CH INPUT STANDBY SURROUND MODE S.SPEAKER B PURE DIRECT SIMPLE SETUP CLEAR ENTER DISPLAY MEMORY MUTE ATT

AUTO HT-EQ MENU EXIT BAND T-MODE POWER ON/OFF SETUP MIC PHONES AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO

1. Press the S (Surround) SPEAKER B button. The unit enters surround speaker B mode and the “SPKR B” will appear on the display. 2. The volume of S. SPEAKER B is interlocked with the main volume. Notes for SURROUND SPEAKER B • SURROUND SPEAKER B On/ Off is available in main room only. • SURROUND SPEAKER B output terminals can be used when the SURROUND BACK SPEAKER is set NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27) • “The Surr. Back Speakers are in use” is displayed by pressing the S. SPEAKER B button when the SURROUND BACK SPEAKER is set except NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27) • Surround Speaker B function is unavailable, while the unit is 7.1 CH input mode. 45

TROUBLESHOOTING E N G In case of trouble, check the following before calling for service: L I 1. Are the connections made properly ? S H 2. Are you operating the unit properly following the user’s guide ? 3. Are the power amplifi ers and speaker working properly ? If the unit does not operate properly, check items shown in the following table. If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz authorized dealer or the Marantz Service Center in your country. SYMPTOM CAUSE REMEDY This unit cannot be turned up. The power plug is not connected. Connect the power plug to the outlet. even when power is on. Mute is on. Cancel mute using the remote controller. No sound and picture are output The input cable is not connected correctly. See the connection diagram and connect the cables correctly. the way down. Adjust the master volume. The master volume control is turned all SYMPTOM CAUSE REMEDY Can not select EX/ES mode. Surround center= NONE has been selected in SPEAKERS SIZE SETUP Make the correct setting. Input signal is incompatible. Use 5.1channel source. Can not select Pro Logic IIx mode. Input signal is incompatible. Use 2 channel Dolby Digital input signal, PCM input signal or analog input signal. Can not select Neo:6 mode. Input signal is incompatible. Use 2 channel Dolby Digital input signal, PCM input signal or analog input signal. Can not select CSII mode. Input signal is incompatible. Use 2 channel Dolby Digital input signal, PCM input signal or analog input signal. No output to Sub Woofer Out. Sub-woofer = NONE has been selected in SETUP mode.Select Sub-woofer = YES. Noise is produced during DTS encoded CD or laser disc play. Analog has been selected for input. Be sure to perform digital connection, select digital input, then play. A specifi c channel does not produce output. Nothing recorded on source. Check the encoded channel on the source side. FM or AM reception fails. Antenna connection is incomplete. Correctly connect the indoor FM and AM antennas to FM and AM antenna outlets. reception. Reception is affected by other electrical

Noise is heard during AM The SOURCE position is wrong. Select correct position. fi elds. Try changing location where the AM indoor antenna is set up.

reception. The radio waves from the broadcasting

No speaker output. The headphones are connected to the headphone jack. Disconnect the headphones. (Speakers will not output sound when headphones are connected.) selected source. Input cable connected incorrectly. Connect the cable correctly by referring to the Noise is heard during FM Cannot get programmed station station are weak.Install an FM outdoor antenna. Preset data has been erased. Disconnecting power plug for long periods of time will erase preset data. If that happens, input the preset

Incorrect Audio or Video for connection diagram. when the PRESET button is pressed. data again.

Incorrect Audio from a channel. Speaker cable connected incorrectly. Connect the cable correctly by referring to the connection diagram. channel speaker. The center speaker cable connection is controller fails. Batteries are consumed. Replace all the batteries with new ones. Control with the remote is wrong. Select different position from which equipment will Remote controller’s function-key setting

No Audio output from the center incomplete. Connect the cable correctly. mode.When STEREO is selected for Surround mode, no be controlled. The distance between this unit and the remote commander is too far.Move closer to this unit.

STEREO has been selected for Surround Center = NONE has been selected in sound will be output from the center speaker. Set another Surround mode. Something is blocking this unit and the remote commander. Remove offending object.

No Audio output from the SETUP mode. Make the correct setting. is incomplete. Connect the cable correctly. MRAC is not working. Headphones are connected. Disconnect the headphones.

surround speakers. The surround speaker cable connection mode.When STEREO has been selected for Surround mode automatically. Are the speakers set to OFF? Set SPK A or SPK B to ON.MRAC is going to CANCEL

STEREO has been selected for Surround Surround = NONE has been selected in mode, no sound will be output from the surround speaker. Set another Surround mode.

SETUP mode. Make the correct setting. surround back speakers. The surround back speaker cable

No Audio output from the connection is incomplete. Connect the cable correctly. Surround mode is not EX/ES mode. Set surround mode EX/ES. Surround back = NONE has been selected in SPEAKERS SIZE SETUP Make the correct setting.

46

HDMI SYMPTOM CAUSE REMEDY 7.1 CH INPUT (SR4002) MULTI (SR5002) AV SURROUND RECEIVER SR4002 SIMPLE SETUP EXIT ATT H SI

The display does not appear over an HDMI connection. The connected monitor or projector does not support HDCP. • Connect to equipment that supports HDCP. • Please change the method of connection. INPUT SELECTOR VOLUME DOWN UP L GN

SURROUND PURE SIMPLE DIRECT SETUP MODE 7.1 CH INPUT S.SPEAKER B The HDMI input of on the TV is not on. Set HDMI input so that it turns on, as explained in the TV’s instruction manual. STANDBY CLEAR ENTER E DISPLAY MEMORY MUTE ATT

AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO POWER ON/OFF SETUP MIC PHONES The HDMI output on the source component (DVD, Set Top Box, etc.) is not on. Set HDMI output so that it turns on, as explained in the source component’s instruction manual.

The SR4002/5002 OSD menu does not appear over an HDMI connection. Time is needed for the display of The HDMI mode is not correctly set on the unit. Set HDMI input on the FUNC INPUT SETUP menu as explained on page 33. The HDMI output video resolution of the source component (DVD, Set Top Box, etc.) does not match the TV specifi cations. Set the resolution so that it matches, as explained in the instruction manuals of both components. The device is connected with a non-standard HDMI cable. A 5 m or shorter cable is recommended to ensure stable operation and prevent image quality deterioration. connections cannot be turned on.) Turn on the power to the unit. Power to the unit is off. (When the unit is on standby, HDMI The connection between HDMI components was not authenticated. Shut off and then turn the power back on to the unit, TV and source component. The unit SETUP menu does not support HDMI output. Use the COMPONENT VIDEO, S-VIDEO or VIDEO output. FRONT KEY (BUTTON) LOCK OF THE UNIT If the SIMPLE SETUP and EXT buttons on the front panel are both pressed at the same time for three seconds or more, all the buttons on the front panel, (excluding the POWER ON/OFF button), as well as the INPUT SELECTOR knob and VOLUME knob, will become locked. “F-KEY LOCK!” will appear in the display. Release the lock by pressing the same two keys again at the same time for three seconds or more. “F-KEY UNLOCK” will appear in the display, and the keys will unlock. GENERAL MALFUNCTION

an HDMI connection to appear. The connection is being authenticated between the HDMI devices. There is nothing wrong with the system. Some HDMI devices require time for authentication. Audio is not played back over an HDMI connection. The HDMI audio output of the source component (DVD, Set Top Box, etc.) is not on. Set the HDMI audio output so that it turns on, as explained in the source component’s instruction manual. The signal format of the source component (DVD, Set Top Box, etc.) is not supported by the unit. Set the HDMI audio output so that it can connect to the unit, as explained in the source component’s instruction manual. The unit is set to the HDMI audio “THROUGH” mode. In the “THROUGH” mode, sound is not produced from the unit. Set it to “ENABLE”. (see page 30) over an HDMI connection. The DVD player does not support CPPM, therefore it cannot If the equipment malfunctions, this may be because an electrostatic discharge or AC line interference has corrupted the information in the equipment memory circuits. Therefore: - disconnect the plug from the AC line supply - after waiting at least three minutes, reconnect the plug to the AC line supply

DVD-Audio is not played back Super Audio CD is not played output HDMI audio. • Use a DVD-Audio player that supports CPPM. • Turn on PCM downsampling on the DVD player. • Use an analog connection. - re-attempt to operate the equipment Memory backup

back over an HDMI connection. The current HDMI connection does not support Super Audio CDs. Use an analog connection. Note: Sometimes, when “PROTECT” is shown on the unit’s display, the standby indicator fl ashes slowly (twice a second). When this happens, turn off the unit’s power and remove the power cable. Then follow the procedure described below: • Check to ensure that the speaker cables connected to the unit have not been connected with + and - connections reversed. • Check to ensure that the speaker cables connected to the unit are not short-circuiting (check the connections both on the unit and on the speakers). (Check that the playback volume is not greater than the unit can handle.) • Check that the playback volume is not greater than the unit can handle. After completing the above checks, connect the power cable and switch the unit back ON using the remote control. Then, after reducing the volume, start playback and check that “PROTECT” is not appearing on the display and that there is no problem with speaker connections to the unit or with sound reproduction. If the same problem re-occurs, please contact your local service center to have it repaired. On rare occasions, the unit will go into standby mode with the standby indicator fl ashing rapidly (eight times a second). When this happens, it means that some major problem has occurred with the unit. Quickly disconnect the power cable and take the unit to your local service center to have it repaired. • In case a power outage occurs or the power cord is accidentally unplugged, this unit is equipped with a backup function to prevent memory data such as the preset memory from being erased. HOW TO RESET THE UNIT Should the operation or display seem to be abnormal, reset the unit with the following procedure. To turn on the SR4002, press and hold the 7.1CH INPUT and ATT buttons simultaneously for 3 seconds or more. To turn on the SR5002, press and hold the MULTI and ATT buttons simultaneously for 3 seconds or more. Remember that the procedure will reset the settings of the SOURCE, Surround mode, delay time, TUNER

PRESET etc., to their initial settings. 47

TECHNICAL SPECIFICATIONS E N G L FM TUNER SECTION DIMENSIONS VIDEO I S

H Frequency Range ................................ 87.5 – 108.0 MHz Usable Sensitivity ............................IHF 1.8 µV/16.4 dBf Signal to Noise Ratio ................... Mono/Stereo 75/70 dB Distortion ......................................Mono/Stereo 0.2/0.3 % Stereo Separation .........................................1 kHz 45 dB Alternate Channel Selectivity .................± 300 kHz 60 dB Image Rejection .........................................98 MHz 70 dB Tuner Output Level ........... 1 kHz, ± 75 kHz Dev 800 mV AM TUNER SECTION Frequency Range ................................... 531 – 1602 kHz Signal to Noise Ratio .............................................. 50 dB Usable Sensitivity ..................................... Loop 400µV/m Distortion ...................................400Hz, 30 % Mod. 0.5 % Selectivity .................................................± 20 kHz 70 dB AUDIO SECTION (SR4002) Power Output (20 Hz – 20 kHz/THD=0.08%) Front L&R ............................................8 ohms 80 W / Ch Center ..................................................8 ohms 80 W / Ch Surround L&R ......................................8 ohms 80 W / Ch Surround Back L&R .............................8 ohms 80 W / Ch Front L&R ..........................................6 ohms 105 W / Ch Center ................................................6 ohms 105 W / Ch Surround L&R ....................................6 ohms 105 W / Ch Surround Back L&R ...........................6 ohms 105 W / Ch Input Sensitivity/Impedance ...............180 mV/ 47 Kohms Signal to Noise Ratio(Analog Input / Pure Direct) .... 105 dB Frequency Response Television Format ............................................ NTSC/PAL Input Level/Impedance ........................... 1 Vp-p/75 ohms Output Level/Impedance ......................... 1 Vp-p/75 ohms Video Frequency Response .......5 Hz to 8 MHz (– 1 dB) Video Frequency (Component) ....5 Hz to 80 MHz (– 1 dB) S/N .......................................................................... 60 dB GENERAL (SR4002) Power Requirement ...................... AC 230 V 50 Hz/60Hz Power Consumption .............................................. 500 W Weight ................................................................. 11.4 Kg GENERAL (SR5002) Power Requirement ...................... AC 230 V 50 Hz/60Hz Power Consumption .............................................. 600 W Weight ................................................................. 12.3 Kg ACCESSORIES Remote Controller RC5001SR ...................................... 1 AAA-size batteries ........................................................ 2 FM Antenna ................................................................... 1 AM Loop Antenna .......................................................... 1 Front AUX Jack Cover ................................................... 1 AC Power Cord .............................................................. 1 Microphone MC-10 ........................................................ 1 User Guide ..................................................................... 1 AV SURROUND RECEIVER SR5002 m m 3 2 m m 1 4 3 m m 0 2 440 mm m m 4 83

(Analog Input / Pure Direct) ...........................................8 Hz – 100 kHz (± 3 dB) (Digital Input / 96 kHz PCM) INPUT SELECTOR VOLUME m DOWN UP m m

PURE SIMPLE m

SURROUNDDISPLAY MEMORYMUTE ATT

MODE MULTI DIRECT SETUP ............................................ 8 Hz – 45 kHz (± 3 dB) MULTI SPEAKER STANDBY CLEAR ENTER 64 0

AUDIO SECTION (SR5002) Power Output (20 Hz – 20 kHz/THD=0.08%) Front L&R ............................................8 ohms 90 W / Ch Center ..................................................8 ohms 90 W / Ch Surround L&R ......................................8 ohms 90 W / Ch Surround Back L&R .............................8 ohms 90 W / Ch SETUP MIC POWER ON/OFF PHONES AUTO HT-EQ MENU EXIT BAND T-MODE AUX 1 INPUT DIGITAL S-VIDEO VIDEO L R AUDIO 1 m m 41 61

Front L&R ..........................................6 ohms 110 W / Ch Center ................................................6 ohms 110 W / Ch Surround L&R ....................................6 ohms 110 W / Ch Surround Back L&R ...........................6 ohms 110 W / Ch Input Sensitivity/Impedance ...............180 mV/ 47 Kohms Signal to Noise Ratio(Analog Input / Pure Direct) .... 105 dB Frequency Response (Analog Input / Pure Direct) ...........................................8 Hz – 100 kHz (± 3 dB) (Digital Input / 96 kHz PCM) .............................................8 Hz – 45 kHz (± 3 dB) Specifi cations subject to change without prior notice.

48

SETUP CODES TV Acer ..........................................................1141 Admiral .................................1002, 1009, 1089 Aiko ..........................................................1059 Aiwa ................................................1117, 1118 Akai ..........................................................1001 Amtron ......................................................1023 Anam ........................................................1113 Anam National ......................1023, 1069, 1092 AOC ........................... 1003, 1024, 1049, 1127 Audiovox ...................................................1023 Bell & Howell ..................................1009, 1025 Benq ...............................................1104, 1142 Broksonic .................. 1003, 1097, 1098, 1113 Celebrity ...................................................1001 Citizen ..................................1003, 1013, 1023 1026, 1059, 1063 Colortyme .......................................1003, 1043 Contec ......................................................1113 Contec/Cony ........................1023, 1045, 1047 Craig .......................... 1020, 1022, 1023, 1113 Crown .............................................1023, 1067 Curtis Mathes .......................1003, 1013, 1025 1026, 1062, 1103, 1110 Daewoo ..................... 1003, 1013, 1024, 1035 1036, 1059, 1084, 1101 Daytron .................................1003, 1013, 1016 Dimensia ........................................1103, 1110 Dumont .................................1003, 1010, 1153 Electroband ..............................................1001 Electrohome .............. 1001, 1003, 1069, 1133 Emerson ...............................1003, 1013, 1015 1020, 1021, 1022, 1023 1025, 1038, 1044, 1045 1048, 1055, 1061, 1094 1096, 1099, 1101, 1113 Envision ....................................................1003 Fisher ........................ 1025, 1051, 1091, 1160 Fujitsu ........................ 1038, 1124, 1125, 1155 Funai ....................................1023, 1038, 1113 Gateway ...................................................1150 GE ............................ 1003, 1018, 1022, 1046 1054, 1069, 1085, 1103 1110, 1113, 1133, 1136, 1153 Goldstar ................................1003, 1013, 1024 1030, 1045, 1080 1100, 1112, 1154 Hallmark ...................................................1003 Hisense ....................................................1116 Hitachi ....................... 1003, 1012, 1031, 1032 1037, 1041, 1045, 1047 1065, 1068, 1082, 1088 1094, 1139, 1140, 1145, 1159 Infi nity .......................................................1067 Janeil ........................................................1134 JBL ...........................................................1067 JC Penney ............................1003, 1013, 1018 1019, 1024, 1026 1046, 1047, 1054 1063, 1083, 1085 1100, 1103, 1110 1112, 1133, 1154 Jensen ......................................................1003 JVC .......................................1028, 1029, 1045 1047, 1050, 1060, 1065 Kawasho .........................................1001, 1003 Kenwood ..................................................1003 Kloss Novabeam ....... 1023, 1056, 1057, 1134 KTV ......................................1013, 1023, 1033 1034, 1073, 1099, 1113 LG ...................................................1024, 1030 M.Wards ...............................1002, 1009, 1038 Magnavox .............................1003, 1052, 1053 1056, 1057, 1063 1067, 1081, 1106 Marantz ..................... 1003, 1031, 1067, 1122 Mitsubishi .............................1003, 1024, 1051 1115, 1122, 1133 Motorola .........................................1014, 1069 NEC ................. 1003, 1012, 1024, 1043, 1069 NET-TV ...........................................1137, 1150 Orion ...............................................1020, 1096 Panasonic ........ 1017, 1067, 1069, 1095, 1111 Philips ........................ 1003, 1011, 1045, 1052 1054, 1056, 1057, 1058 1063, 1067, 1069, 1106 Pioneer .................................1003, 1018, 1037 1070, 1071, 1094 1145, 1147, 1149 Plasmsync ................................................1135 Portland ..................... 1003, 1013, 1024, 1059 Price Club .................................................1026 Prism ........................................................1018 Video Concepts ........................................1113 Viewsonic .............................1006, 1022, 1109 1128, 1129, 1130, 1131 1138, 1143, 1145, 1150 Wards ...................................1003, 1009, 1015 1024, 1038, 1044, 1046 1052, 1054, 1056, 1057 1067, 1086, 1103, 1110 White Westinghouse ......................1001, 1101 Yamaha ..........................................1003, 1024 Zenith ...................................1003, 1009, 1010 1132, 1144, 1153 VCR Admiral ...........................................3026, 3060 Adventura .................................................3035 Aiko ..........................................................3038 Aiwa ................................................3035, 3039 Akai ................................................3003, 3053 3054, 3072, 3073 American High .........................................3009 Asha .........................................................3021 Audio Dynamics ...................3034, 3040, 3083 Audiovox ...................................................3052 Beaumark .......................................3017, 3021 Bell & Howell ............................................3029 Broksonic .......................................3029, 3075 Calix .........................................................3052 Candle ..................................3012, 3021, 3034 3038, 3050, 3052, 3056 Canon .............................................3008, 3009 Capehart ..................................................3050 Carver .............................................3045, 3062 CCE ................................................3038, 3067 Challenger ................................................3078 Citizen ............. 3012, 3021, 3038, 3052, 3056 Colortyme .......................................3034, 3079 Colt ...........................................................3067 Craig .......................... 3021, 3032, 3052, 3067 Criterion ....................................................3067 Curtis Mathes .................................3008, 3009 3021, 3034, 3063 Cybernex ..................................................3021 Daewoo ................................3035, 3038, 3050 Daytron ...........................................3038, 3050 DBX ......................................3034, 3040, 3083 Denon .......................................................3005 i Proscan ..................... 1004, 1005, 1006, 1007 1008, 1085, 1103, 1110 Proton .............................................1003, 1045 Quasar ............ 1010, 1069, 1073, 1111, 1153 Radio Shack .........................1003, 1013, 1015 1023, 1024, 1025, 1045 1100, 1103, 1110, 1113 RCA ......................................1003, 1004, 1005 1006, 1007, 1008 1014, 1024, 1049, 1069 1075, 1079, 1085, 1087 1088, 1093, 1094, 1101 1103, 1110, 1113, 1153 Realistic ..................... 1013, 1015, 1023, 1025 1045, 1100, 1103, 1110 Runco .............................................1010, 1153 Sampo ......................................................1150 Samsung ................... 1003, 1013, 1024, 1026 1040, 1045, 1062, 1078 1083, 1090, 1100, 11051114 1120, 1121, 1146, 1148, 1157 Sansui ......................................................1119 Sanyo ........................ 1003, 1025, 1051, 1072 1077, 1091, 1156, 1157, 1158 Sharp ....................................1003, 1013, 1014 1015, 1045, 1055, 1064 1066, 1076, 1089, 1123 Signature ..................................................1009 Sony .....................................1001, 1102, 1108 Soundesign ..... 1003, 1023, 1038, 1063, 1113 Starlite ......................................................1023 Supre-Macy ..............................................1134 Sylvania ................................1003, 1039, 1042 1052, 1053, 1056, 1057 1063, 1067, 1089, 1151 Symphonic ...........................1023, 1039, 1044 Tandy ........................................................1014 Tatung .......................................................1069 Technics ...................................................1018 Techwood .......................................1003, 1018 Teknika ...................... 1003, 1009, 1013, 1023 1024, 1026, 1038, 1045 1047, 1059, 1063, 1111, 1113 Telecaption ...............................................1074 Toshiba .................................1003, 1019, 1025 1026, 1042, 1074, 1098 1107, 1111, 1135, 1136 Totevision .................................................1013 Universal ........................................1046, 1054 Dimensia ..............................3004, 3063, 3085 Dixon ..............................................3077, 3081 Dynatech ..................................................3035 Electrohome .............................................3052 Electrophonic ...........................................3052 Emerson .................... 3009, 3015, 3016, 3017 3018, 3019, 3022, 3035 3047, 3052, 3054, 3073 Fisher .............................................3029, 3032 Fuji ..................................................3003, 3009 Funai ..............................................3035, 3056 Garrard .....................................................3035 GE ........................................3004, 3008, 3009 3021, 3028, 3058 3063, 3074, 3085 Go Video ..............................3021, 3036, 3037 3052, 3067, 3068, 3069 Goldstar ..................... 3021, 3031, 3034, 3052 Gradiente .......................................3035, 3052 Harley Davidson .......................................3035 Harman Kardon ..............................3034, 3045 Harwood ...................................................3067 Headquarter .............................................3029 Hitachi ............. 3004, 3005, 3055, 3072, 3074 Homeline ..................................................3052 Instant Replay ..........................................3009 JBL ...........................................................3002 JC Penney ................. 3005, 3008, 3009, 3017 3021, 3029, 3034, 3040 3052, 3062, 3067, 3083 JCL ...........................................................3009 Jensen ............................................3005, 3072 JVC .......................................3014, 3015, 3034 3040, 3041, 3042 3048, 3049, 3072, 3083 Kenwood ................... 3029, 3034, 3048, 3072 KLH ..........................................................3067 Kodak .............................................3009, 3052 LG ...................................................3031, 3052 Lloyds ...................................3034, 3035, 3056 Logik .........................................................3067 LXI ............................................................3052 Magnasonic ..........................3038, 3052, 3067 Magnavox .............................3008, 3009, 3010 3045, 3067, 3071 Magnin ...........................................3021, 3052 Marantz ................................3009, 3029, 3034 3040, 3045, 3062, 3083 Marta ........................................................3052 MEI ...........................................................3009 Memorex ..............................3005, 3009, 3021 3026, 3029, 3032, 3035 3052, 3060, 3067, 3071 MGA ...............................................3022, 3073 MGN Technology ......................................3021 Midland .....................................................3056 Minolta ......................................................3005 Mitsubishi .............................3005, 3022, 3023 3025, 3048, 3052, 3073 Montgomery Ward ..........................3026, 3060 Motorola ...............................3009, 3026, 3060 MTC ................................................3021, 3067 Multitech ...............................3021, 3035, 3067 NEC ......................................3033, 3034, 3040 3048, 3072, 3083 Nikko ........................................................3052 Noblex ......................................................3021 Olympus ...................................................3009 Optimus ................................3026, 3052, 3060 Optonica ...................................................3027 Orion .......................... 3015, 3017, 3047, 3052 Panasonic ........ 3006, 3007, 3008, 3009, 3067 Pentax ..................................3005, 3034, 3074 Philco ............... 3005, 3008, 3009, 3047, 3062 Philips .............. 3009, 3010, 3027, 3045, 3062 Pilot ..........................................................3052 Pioneer .................................3005, 3040, 3046 3048, 3061, 3080, 3083 Portland ....................................................3050 Proscan ................................3004, 3063, 3085 Protec .......................................................3067 Proton .......................................................3067 Pulsar ........................ 3021, 3038, 3056, 3071 Quarter ...........................................3029, 3084 Quartz ............................................3029, 3084 Quasar ...........................................3008, 3009 Radio Shack .............. 3021, 3052, 3009, 3008 3035, 3027, 3060, 3026 Radix ........................................................3052 Randex .....................................................3052 RCA ......................................3004, 3005, 3009 3021, 3046, 3054, 3057 3061, 3063, 3074, 3085 Realistic ..................... 3008, 3009, 3012, 3021 3026, 3027, 3029, 3032 3035, 3052, 3060, 3084 Ricoh ..............................................3002, 3059 Runco .......................................................3071 DVD Aiwa ................................................2036, 2037 Apex ...... 2012, 2017, 2018, 2019, 2021, 2034 BOSE .............................................2038, 2039 Denon .............................................2047, 2048 Funai ........................................................2049 GE ............................. 2009, 2020, 2029, 2033 Harman Kardon ........................................2061 Hitachi ..................................2008, 2012, 2031 JVC .......................................2006, 2010, 2040 2041, 2042, 2043 Kenwood ........................................2053, 2054 Koss ..........................................................2058 Magnavox .................. 2007, 2011, 2023, 2025 Marantz ....................................................2025 Mitsubishi .......................................2011, 2015 Onkyo .......................................................2062 Oritron ............................................2009, 2030 Panasonic .................. 2003, 2015, 2016, 2055 Philips ...................................2007, 2011, 2058 Pioneer .................................2002, 2014, 2056 Proscan ................................2009, 2020, 2032 RCA ................. 2005, 2009, 2020, 2035, 2057 Sampo ......................................................2041 Samsung ......... 2008, 2012, 2022, 2024, 2027 Sanyo .............................................2050, 2052 Sharp ..............................................2044, 2045 Sherwood .................................................2051 Sony .....................................2001, 2013, 2059 Toshiba ...................... 2004, 2008, 2026, 2028 Yamaha ..........................................2046, 2060 Zenith .......................................................2010 DSS Alphastar ..................................................4027 BSB ..........................................................4021 Chaparral .................................................4039 DIRECTV .......................................4001, 4016 DISH Network ..........................................4030 Drake ........................................................4026 Echostar .......... 4007, 4017, 4018, 4019, 4020 Express Vu ...............................................4017 Fujitsu .......................................................4025 GE ........................................4002, 4008, 4009 General Instruments ......................4036, 4037 Hitachi ............................................4001, 4015 ii Samsung ..............................3013, 3020, 3021 3056, 3068, 3069, 3070 Sanky ...................................3026, 3060, 3071 Sansui ............. 3040, 3048, 3067, 3072, 3083 Sanyo ...................................3021, 3029, 3032 Scott .......................... 3012, 3017, 3022, 3052 Sears ....................................3005, 3009, 3029 3032, 3034, 3052, 3084 Sharp ......................... 3026, 3027, 3060, 3064 Shintom ................................3003, 3005, 3067 Shogun .....................................................3021 Signature ........................................3026, 3060 Signature 2000 .....................3026, 3029, 3084 Singer ........................ 3002, 3009, 3059, 3067 Sony .......................... 3001, 3003, 3043, 3065 STS ................................................3005, 3009 Sylvania ................................3008, 3009, 3022 3035, 3045, 3062, 3076 Symphonic ...........................3034, 3035, 3056 Tandy ..............................................3029, 3084 Tashiko .....................................................3052 Tatung .......................................................3072 Teac ................................................3035, 3072 Technics .........................................3007, 3009 Teknika .................................3009, 3035, 3052 TMK ..........................................................3021 Toshiba .................................3005, 3011, 3012 3022, 3051, 3073 Totevision .......................................3021, 3052 Unitec .......................................................3056 Unitech .....................................................3021 Vector Research ........ 3012, 3034, 3040, 3083 Victor ..............................................3040, 3083 Video Concepts ..............................3012, 3034 3040, 3073, 3083 Videosonic ................................................3021 Wards ...................................3005, 3009, 3012 3021, 3026, 3027 3032, 3035, 3045 3052, 3060, 3061, 3067 White Westinghouse ......................3035, 3056 XR-1000 ...............................3009, 3035, 3067 Yamaha ................................3029, 3034, 3040 3072, 3083, 3084 Zenith .............. 3030, 3052, 3053, 3059, 3071

Hughes ...........................................4001, 4016 Janeil ........................................................4025 JVC ...........................................................4017 Mitsubishi .................................................4001 Panasonic .......................................4004, 4010 Philips .............................................4031, 4035 Proscan ..................... 4002, 4008, 4009, 4011 Radio Shack ...................................4036, 4037 RCA ........................... 4002, 4008, 4009, 4029 Realistic ....................................................4040 Rural Cable ..............................................4036 Samsung ........................................4022, 4027 Sony .....................................4003, 4012, 4014 Star Choice ..............................................4032 Star Trak ...................................................4024 STS ..........................................................4038 SuperDish ................................................4028 Toshiba ...........................................4001, 4034 Uniden ..................................4005, 4006, 4013 Video Pall .................................................4025 Zenith .............................................4025, 4033 iii marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark. Printed in China 07/2007 00M32CW851310 mzh-d


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply