MAKITA RT001G (01) PDF Document

Due to a continuing program of research and development, these specifications are subject to change without notice. Specifications and battery cartridge may differ from country to country. The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Some of the battery cartridges and chargers listed may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed. Use of any other battery cartridges and chargers may cause injury and/or fire.

The MAKITA RT001G tool is intended for flush trimming and profiling of wood, plastic, and similar materials.

Noise:

The typical A-weighted noise level determined according to EN62841-2-17:

Work mode: rotation without load

Sound pressure level (LpA): 81 dB(A)

Sound power level (LwA): 92 dB(A)

Uncertainty (K): 3 dB(A)

NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection. The noise emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used, especially what kind of workpiece is processed. Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

Vibration:

The vibration total value (tri-axial vector sum) determined according to EN62841-2-17:

Work mode: rotation without load

Vibration emission (ah): 2.5 m/s² or less

Uncertainty (K): 1.5 m/s²

NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used, especially what kind of workpiece is processed. Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety:

1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety:

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

7. Power tools can produce electromagnetic fields (EMF) that are not harmful to the user. However, users of pacemakers and other similar medical devices should contact the maker of their device and/or doctor for advice before operating this power tool.

Personal safety:

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

9. Always wear protective goggles to protect your eyes from injury when using power tools. The goggles must comply with ANSI Z87.1 in the USA, EN 166 in Europe, or AS/NZS 1336 in Australia/New Zealand. In Australia/New Zealand, it is legally required to wear a face shield to protect your face, too.

1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

5. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

8. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

9. When using the tool, do not wear cloth work gloves which may be entangled. The entanglement of cloth work gloves in the moving parts may result in personal injury.

1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

3. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

5. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.

7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

1. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by your hand or against the body leaves it unstable and may lead to loss of control.

2. Hold the power tool by insulated gripping surfaces only, because the cutter may contact hidden wiring. Cutting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

3. Only use a trimmer bit that is rated at least equal to the maximum speed marked on the tool. If the tool has a variable speed control function, set the tool speed under the speed rating of the trimmer bit.

4. The trimmer bit shank must match the designed collet chuck.

5. Wear hearing protection during extended period of operation.

6. Handle the trimmer bits very carefully.

7. Check the trimmer bit carefully for cracks or damage before operation. Replace cracked or damaged trimmer bit immediately.

8. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation.

9. Hold the tool firmly.

10. Keep hands away from rotating parts.

11. Make sure the trimmer bit is not contacting the workpiece before the switch is turned on.

12. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed trimmer bit.

13. Be careful of the trimmer bit rotating direction and the feed direction.

14. Do not leave the tool running. Operate the tool only when hand-held.

15. Always switch off and wait for the trimmer bit to come to a complete stop before removing the tool from workpiece.

16. Do not touch the trimmer bit immediately after operation; it may be extremely hot and could burn your skin.

17. Do not smear the base carelessly with thinner, gasoline, oil or the like. They may cause cracks in the base.

18. Use trimmer bits of the correct shank diameter suitable for the speed of the tool.

19. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

20. Always use the correct dust mask/respirator for the material and application you are working with.

1. Before using the battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the battery.

2. Do not disassemble or tamper with the battery cartridge. It may result in a fire, excessive heat, or explosion.

3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

6. Do not store and use the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

8. Do not nail, cut, crush, throw, drop the battery cartridge, or hit against a hard object to the battery cartridge. Such conduct may result in a fire, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirement on packaging and labeling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.

11. When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.

12. Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time, the battery must be removed from the tool.

14. During and after use, the battery cartridge may take on heat which can cause burns or low temperature burns. Pay attention to the handling of hot battery cartridges.

15. Do not touch the terminal of the tool immediately after use as it may get hot enough to cause burns.

16. Do not allow chips, dust, or soil stuck into the terminals, holes, and grooves of the battery cartridge. It may cause heating, catching fire, burst and malfunction of the tool or battery cartridge, resulting in burns or personal injury.

17. Unless the tool supports the use near high-voltage electrical power lines, do not use the battery cartridge near a high-voltage electrical power lines. It may result in a malfunction or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove it from the tool or the charger.

5. Charge the battery cartridge if you do not use it for a long period (more than six months).

1. Do not disassemble or tamper with the wireless unit.

2. Keep the wireless unit away from young children. If accidentally swallowed, seek medical attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet conditions.

5. Do not use the wireless unit in places where the temperature exceeds 50 °C (122 °F).

6. Do not operate the wireless unit in places where medical instruments, such as heart pacemakers are nearby.

7. Do not operate the wireless unit in places where automated devices are nearby. If operated, automated devices may develop malfunction or error.

8. Do not operate the wireless unit in places under high temperature or places where static electricity or electrical noise could be generated.

9. The wireless unit can produce electromagnetic fields (EMF) but they are not harmful to the user.

10. The wireless unit is an accurate instrument. Be careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless unit with bare hands or metallic materials.

12. Always remove the battery on the product when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the place where dust and water may come into the slot. Always keep the inlet of the slot clean.

14. Always insert the wireless unit in the correct direction.

15. Do not press the wireless activation button on the wireless unit too hard and/or press the button with an object with a sharp edge.

16. Always close the lid of the slot when operating.

17. Do not remove the wireless unit from the slot while the power is being supplied to the tool. Doing so may cause a malfunction of the wireless unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20. Do not leave the wireless unit in a place where static electricity or electrical noise could be generated.

21. Do not leave the wireless unit in a place subject to high heat, such as a car sitting in the sun.

22. Do not leave the wireless unit in a dusty or powdery place or in a place corrosive gas could be generated.

23. Sudden change of the temperature may bedew the wireless unit. Do not use the wireless unit until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe with a dry soft cloth. Do not use benzine, thinner, conductive grease or the like.

25. When storing the wireless unit, keep it in the supplied case or a static-free container.

26. Do not insert any devices other than Makita wireless unit into the slot on the tool.

27. Do not use the tool with the lid of the slot damaged. Water, dust, and dirt come into the slot may cause malfunction.

28. Do not pull and/or twist the lid of the slot more than necessary. Restore the lid if it comes off from the tool.

29. Replace the lid of the slot if it is lost or damaged.

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

CAUTION: Always switch off the tool before installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

CAUTION: Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.

Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for a few seconds.

Indicator lamps			Remaining capacity
Lighted	Off	Blinking
			75% to 100%
			50% to 75%
			25% to 50%
			0% to 25%
			Charge the battery.
			The battery may have malfunctioned.

NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.

NOTE: The first (far left) indicator lamp will blink when the battery protection system works.

The MAKITA RT001G is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions:

Overload protection: When the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.

Overheat protection: When the tool or battery is overheated, the tool stops automatically. In this case, let the tool and battery cool before turning the tool on again.

Overdischarge protection: When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery.

Protections against other causes: The protection system is also designed for other causes that could damage the tool and allows the tool to stop automatically. Take all the following steps to clear the causes, when the tool has been brought to a temporary halt or stop in operation:

1. Turn the tool off, and then turn it on again to restart.

2. Charge the battery(ies) or replace it/them with recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection system, then contact your local Makita Service Center.

To turn on the tool, press the lock/unlock button. The tool turns into the standby mode. To start the tool, press the start/stop button in the standby mode. To stop the tool, press the start/stop button again. The tool turns into the standby mode. To turn off the tool, press the lock/unlock button in the standby mode.

NOTE: If the tool is left for 10 seconds without any operation in the standby mode, the tool automatically turns off and the lamp goes off.

NOTE: You can also stop and turn off the tool by pressing the lock/unlock button while the tool is operating.

CAUTION: Do not look in the light or see the source of light directly.

To turn on the lamp, press the lock/unlock button. To turn off the lamp, press the lock/unlock button again.

NOTICE: When the tool is overheated, the lamp blinks. Cool down the tool fully before operating the tool again.

NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.

The rotation speed of the tool can be changed by turning the speed adjusting dial. The table below shows the number on the dial and the corresponding rotation speed.

CAUTION: Do not change the rotation speed during operation. Otherwise unexpected reaction of the tool may cause an injury.

NOTICE: If the tool is operated continuously at low speed for a long time, the motor will get overloaded, resulting in tool malfunction.

NOTICE: The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work.

The MAKITA RT001G is equipped with electronic functions for easy operation:

Constant speed control: The speed control function provides the constant rotation speed regardless of load conditions.

Soft start: The soft-start function minimizes start-up shock, and makes the tool start smoothly.

Soft brake: The tool stops gently with the soft brake. The soft brake prevents damage to the workpiece due to recoil and allows you to start next operation earlier. If the tool consistently fails to stop the trimmer bit after the switch is turned off, have the tool serviced at a Makita service center.

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

NOTICE: Do not tighten the collet nut without installing a trimmer bit, or the collet cone may break.

1. Insert the trimmer bit all the way into the collet cone.

2. Press the shaft lock and tighten the collet nut with the wrench. You can also tighten the collet nut securely with two wrenches.

To remove the trimmer bit, follow the installation procedure in reverse.

NOTE: The shaft lock may not return to the original position when you tighten the collet nut in the installation of the trimmer bit. The shaft lock returns to the original position when you start the tool.

CAUTION: Use the correct size collet cone for the trimmer bit which you intended to use.

CAUTION: Do not tighten the collet nut without installing a trimmer bit, or the collet cone may break.

1. Loosen the collet nut and remove.

2. Replace the installed collet cone with desired collet cone.

3. Reinstall collet nut.

1. Open the lock lever of the trimmer base, then insert the tool into the trimmer base aligning the groove on the tool with the protrusion on the trimmer base.

2. Close the lock lever.

NOTE: You can use the trimmer base (resin) as an optional accessory. When using the trimmer base (resin), loosen or tighten the thumb nut instead of opening or closing the lock lever. Align the rack on the tool with the spur gear on the trimmer base.

To remove the base, follow the installation procedure in reverse.

Dust Nozzle Installation:

1. Attach the dust nozzle to the trimmer base, and then tighten the thumb screw.

CAUTION: When using the tool with the trimmer base, be sure to install the dust nozzle on the trimmer base.

Installing/Removing the Tilt Base (Optional Accessory)

1. Open the lock lever of the tilt base, then insert the tool into the tilt base aligning the groove on the tool with the protrusion on the tilt base.

2. Close the lock lever.

To remove the base, follow the installation procedure in reverse.

Installing/Removing the Offset Base (Optional Accessory)

1. Press the shaft lock, then loosen the collet nut.

2. Remove the collet nut and the collet cone.

3. Install the pulley onto the tool by pressing the shaft lock and tightening the pulley with the wrench.

4. Loosen the screws on the base plate, and then remove the base plate.

5. Open the lock lever of the offset base, then attach the offset base to the tool.

6. Mount the belt to the pulley with a stick like a slotted screwdriver by rotating the belt manually.

7. Close the lock lever.

8. Attach the base plate by tightening the screws.

9. Insert the collet cone and the trimmer bit into the offset base, and then tighten the collet nut.

10. Insert the hex wrench into the hole of the offset base, and then tighten the collet nut with the wrench.

To remove the base, follow the installation procedure in reverse.

NOTE: You can also mount the belt to the pulley without removing the base plate.

Installing/Removing the Plunge Base (Optional Accessory)

1. Open the lock lever of the plunge base, then insert the tool into the plunge base all the way aligning the groove on the tool with the protrusion on the plunge base.

2. Close the lock lever.

To remove the base, follow the installation procedure in reverse.

Adjusting Cutting Depth with the Trimmer Base:

To adjust the cutting depth, open the lock lever, then move the tool base up or down by turning the adjusting screw. After the adjustment, close the lock lever firmly.

NOTICE: If the tool is not secured after closing the lock lever, tighten the hex nut, and then close the lock lever.

Adjusting Cutting Depth with the Plunge Base (Optional Accessory):

1. Place the tool on a flat surface.

2. Select the stopper screw by rotating the stopper base.

3. Loosen the fixing nut, then pull up the stopper pole while pressing the feed button.

4. Push down the tool until the tip of the trimmer bit touches the flat surface, and then turn the fixing lever to secure the tool.

5. Press down the stopper pole while pressing the feed button until it contacts the stopper screw.

6. Slide the depth pointer so that the pointer indicates “0” on the scale.

7. Adjust the cutting depth by pulling up the stopper pole while pressing the feed button.

8. To perform fine adjustment of the cutting depth, turn the dial on the stopper pole so that it indicates “0”.

9. Turn the head of the stopper pole to obtain the desired depth. To increase the depth, turn the head counterclockwise. To decrease the depth, turn the head clockwise. (The depth changes by 1 mm per one revolution.)

10. Tighten the stopper pole fixing nut.

11. Release the fixing lever.

By pushing down the tool until the stopper pole meets the stopper screw, you can obtain the depth of cut which you adjusted by the above procedure.

Set the tool base on the workpiece without the trimmer bit making any contact. Turn the tool on and wait until the trimmer bit attains full speed. Move the tool forward over the workpiece surface. Keep the tool base flush while moving the tool.

When cutting the edge, be sure to keep the workpiece surface on the left side of the trimmer bit in the feed direction.

NOTE: Before cutting on the actual workpiece, it is recommended to make a sample cut. The proper feed speed depends on the trimmer bit size, the kind of workpiece, and depth of cut. Moving the tool forward too fast may cause a poor quality of cut, or damage to the trimmer bit or motor. Moving the tool forward too slowly may burn and mar the cutting surface.

When using the trimmer shoe, the straight guide, or the trimmer guide, be sure to keep it on the right side in the feed direction. This will help to keep it flush with the side of the workpiece.

NOTICE: Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 3 mm at a pass when cutting grooves. When you wish to cut grooves more than 3 mm deep, make several passes with progressively deeper trimmer bit settings.

Using the Straight Guide (with Trimmer Base)

1. Assemble the straight guide with the bolt and the wing nut.

2. Attach the straight guide to the trimmer base with the clamp screw.

3. Loosen the wing nut on the straight guide and adjust the distance between the trimmer bit and the straight guide. At the desired distance, tighten the wing nut.

4. Move the tool with the straight guide flush with the side of the workpiece.

If the distance between the workpiece side and cutting position is too wide, or the workpiece side is not straight, firmly clamp a straight board to the workpiece and use it as a guide.

Using the Straight Guide for Circular Work

Assemble the straight guide as shown in the figures. The minimum radius is 70 mm and the maximum is 221 mm.

Align the center hole in the straight guide with the center of the circle to be cut. Drive a nail (less than 6 mm diameter) into the center hole to secure the guide. Pivot the tool around the nail in a clockwise direction.

Using the Templet Guide

1. Loosen the screws on the base plate, and then remove the base plate from the trimmer base.

2. Place the templet guide on the base, and then attach the base plate by tightening the screws.

3. Place the tool on the templet and move the tool so that the templet guide slides along the side of the templet.

Using the Trimmer Guide (Optional Accessory)

1. Loosen the clamp screw, then install the trimmer guide on the trimmer base, and then tighten the clamp screw.

2. Loosen the clamp screw and adjust the distance between the trimmer bit and the trimmer guide by turning the adjusting screw (1 mm per turn). At the desired distance, tighten the clamp screw.

3. Move the tool with the guide roller riding the side of the workpiece.

Using the Tool with the Tilt Base

The tilt base is convenient for chamfering. Loosen the wing screws, tilt the tool to the desired angle, and then tighten the wing screws. Firmly clamp a straight board to the workpiece and use it as a guide against the tilt base. Feed the tool in the direction of the arrow.

Using the Tool with the Offset Base

The offset base is used for trimming the edge of laminate sheet or similar materials and is convenient for work in a tight area.

Using the Tool with the Plunge Base

Always hold the grips firmly with both hands during operation. Operate the tool in the same way as the trimmer base.

The wireless activation function enables clean and comfortable operation. By connecting a supported vacuum cleaner to the MAKITA RT001G, you can run the vacuum cleaner automatically along with the switch operation of the tool.

To use this function, you need:

A wireless unit (optional accessory)

A vacuum cleaner which supports the wireless activation function

The setup overview is as follows:

1. Installing the wireless unit

2. Tool registration for the vacuum cleaner

3. Starting the wireless activation function

CAUTION: Place the tool on a flat and stable surface when installing the wireless unit.

NOTICE: Clean the dust and dirt on the tool before installing the wireless unit. Dust or dirt may cause malfunction if it comes into the slot of the wireless unit.

NOTICE: To prevent malfunction caused by static, touch a static discharging material, such as a metal part of the tool, before picking up the wireless unit.

NOTICE: When installing the wireless unit, always be sure that the wireless unit is inserted in the correct direction and the lid is completely closed.

1. Open the lid on the tool as shown in the figure.

2. Insert the wireless unit to the slot and then close the lid. When inserting the wireless unit, align the projections with the recessed portions on the slot.

When removing the wireless unit, open the lid slowly. The hooks on the back of the lid will lift the wireless unit as you pull up the lid.

NOTICE: Always use the hooks on the back of the lid when removing the wireless unit. If the hooks do not catch the wireless unit, close the lid completely and open it slowly again.

NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for tool registration. Finish installing the wireless unit to the tool before starting.

NOTE: During registration, do not pull the switch trigger or turn on the power switch on the vacuum cleaner.

1. Install the batteries to the vacuum cleaner and the tool.

2. Set the stand-by switch on the vacuum cleaner to “AUTO”.

3. Press the wireless activation button on the vacuum cleaner for 3 seconds until the wireless activation lamp blinks in green. And then press the wireless activation button on the tool in the same way.

If the vacuum cleaner and tool are linked successfully, the wireless activation lamps will light up in green for 2 seconds and start blinking in blue.

NOTE: The wireless activation lamps finish blinking in green after 20 seconds elapsed. Press the wireless activation button on the tool while the wireless activation lamp on the cleaner is blinking. If the lamp does not blink in green, push the button briefly and hold it down again.

NOTE: When performing two or more tool registrations for one vacuum cleaner, finish the registration one by one.

NOTE: Finish the tool registration for the vacuum cleaner prior to wireless activation.

After registering the tool, the vacuum cleaner will automatically run along with the tool’s switch operation.

1. Install the wireless unit to the tool.

2. Connect the hose of the vacuum cleaner with the tool.

3. Set the stand-by switch on the vacuum cleaner to “AUTO”.

4. Push the wireless activation button on the tool briefly. The wireless activation lamp will blink in blue.

5. Turn on the tool. Check if the vacuum cleaner runs while the tool is operating.

To stop the wireless activation of the vacuum cleaner, push the wireless activation button on the tool.

NOTE: The wireless activation lamp on the tool will stop blinking in blue when there is no operation for 2 hours. In this case, set the stand-by switch on the vacuum cleaner to “AUTO” and push the wireless activation button on the tool again.

NOTE: The vacuum cleaner starts/stops with a delay. There is a time lag when the vacuum cleaner detects a switch operation of the tool.

NOTE: The transmission distance of the wireless unit may vary depending on the location and surrounding circumstances.

NOTE: When two or more tools are registered to one vacuum cleaner, the vacuum cleaner may start running even if you do not turn on your tool because another user is using the wireless activation function.

The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the meaning of the lamp status.

Perform the following procedure when cancelling the tool registration for the vacuum cleaner:

1. Install the batteries to the vacuum cleaner and the tool.

2. Set the stand-by switch on the vacuum cleaner to “AUTO”.

3. Press the wireless activation button on the vacuum cleaner for 6 seconds. The wireless activation lamp blinks in green and then becomes red. After that, press the wireless activation button on the tool in the same way.

If the cancellation is performed successfully, the wireless activation lamps will light up in red for 2 seconds and start blinking in blue.

NOTE: The wireless activation lamps finish blinking in red after 20 seconds elapsed. Press the wireless activation button on the tool while the wireless activation lamp on the cleaner is blinking. If the wireless activation lamp does not blink in red, push the wireless activation button briefly and hold it down again.

If the wireless activation lamp does not light/blink, check the following:

Probable cause: The wireless unit is not installed or improperly installed.

Remedy: Install the wireless unit correctly.

Probable cause: The terminal of the wireless unit and/or the slot is dirty.

Remedy: Gently wipe off dust and dirt on the terminal of the wireless unit and clean the slot.

Probable cause: The wireless activation button on the tool has not been pushed.

Remedy: Push the wireless activation button on the tool briefly.

Probable cause: The stand-by switch on the vacuum cleaner is not set to “AUTO”.

Remedy: Set the stand-by switch on the vacuum cleaner to “AUTO”.

Probable cause: No power supply.

Remedy: Supply the power to the tool and the vacuum cleaner.

If you cannot finish tool registration/cancellation successfully, check these possible causes:

Probable cause: The wireless unit is not installed or is improperly installed.

Remedy: Install the wireless unit correctly.

Probable cause: The terminal of the wireless unit and/or slot is dirty.

Remedy: Gently wipe off dust and dirt from the terminal and clean the slot.

Probable cause: The stand-by switch on the vacuum cleaner is not set to “AUTO”.

Remedy: Set the switch to “AUTO”.

Probable cause: No power supply.

Remedy: Supply power to the tool and vacuum cleaner.

Probable cause: Incorrect operation.

Remedy: Push the wireless activation button briefly and perform the registration/cancellation procedures again.

Probable cause: The tool and vacuum cleaner are too far apart.

Remedy: Move the tool and vacuum cleaner closer to each other. The maximum transmission distance is approximately 10 m but may vary.

Probable cause: The tool switch or vacuum power button was turned on before finishing registration/cancellation.

Remedy: Push the wireless activation button briefly and perform the procedures again.

Probable cause: Registration procedures for the tool or vacuum cleaner have not been finished.

Remedy: Perform the registration procedures for both the tool and vacuum cleaner at the same time.

Probable cause: Radio disturbance from other appliances like Wi-Fi devices or microwaves.

Remedy: Keep the tool and vacuum cleaner away from such appliances.

If the vacuum cleaner does not run along with the tool, check these possible causes:

Probable cause: The wireless unit is not installed or is improperly installed.

Remedy: Install the wireless unit correctly.

Probable cause: The terminal of the wireless unit and/or slot is dirty.

Remedy: Gently wipe off dust and dirt and clean the slot.

Probable cause: The wireless activation button on the tool has not been pushed.

Remedy: Push the wireless activation button briefly and make sure the lamp is blinking in blue.

Probable cause: The stand-by switch on the vacuum cleaner is not set to “AUTO”.

Remedy: Set the switch to “AUTO”.

Probable cause: More than 10 tools are registered to the vacuum cleaner.

Remedy: Perform the tool registration again. The earliest registered tool will be cancelled automatically.

Probable cause: The vacuum cleaner erased all tool registrations.

Remedy: Perform the tool registration again.

Probable cause: No power supply.

Remedy: Supply power to the tool and vacuum cleaner.

Probable cause: The tool and vacuum cleaner are too far apart.

Remedy: Move the tool and vacuum cleaner closer together.

Probable cause: Radio disturbance from other high-intensity radio wave appliances.

Remedy: Keep the tool and vacuum cleaner away from appliances like Wi-Fi devices and microwaves.

If the vacuum cleaner runs while the tool is not operating, this may be the cause:

Probable cause: Other users are using the wireless activation of the vacuum cleaner with their tools.

Remedy: Turn off the wireless activation button of the other tools or cancel the tool registration of the other tools.

CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

Straight and groove forming bits

Edge forming bits

Laminate trimming bits

Straight guide assembly

Trimmer guide assembly

Trimmer base assembly

Trimmer base assembly (resin)

Tilt base assembly

Plunge base assembly

Offset base assembly

Grip attachment

Templet guide

Collet cone

Wrench 13

Wrench 22

Wireless unit

Makita genuine battery and charger

NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.