FREE ENGLISH MAKITA DPB181 (01) PDF USER GUIDE
FREE ENGLISH MAKITA DPB181 (01) PDF USER MANUAL
FREE ENGLISH MAKITA DPB181 (01) PDF OWNER GUIDE
FREE ENGLISH MAKITA DPB181 (01) PDF OWNER MANUAL
FREE ENGLISH MAKITA DPB181 (01) PDF REFERENCE GUIDE
FREE ENGLISH MAKITA DPB181 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH MAKITA DPB181 (01) PDF REFERENCE MANUAL
FREE ENGLISH MAKITA DPB181 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH MAKITA DPB181 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD MAKITA DPB181 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
MAKITA DPB181 (01) PDF SUMMARY:
What is the maximum cutting capacity for a round workpiece?
64 mm (2-1/2") dia.
What is the maximum cutting capacity for a rectangular workpiece?
64 mm x 64 mm (2-1/2" x 2-1/2").
What should I do before using the battery cartridge?
Before using the battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
Should I disassemble the battery cartridge?
No, do not disassemble the battery cartridge.
What should I do if operating time has become excessively shorter?
If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
What should I do if electrolyte gets into my eyes?
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of eyesight.
Should I short the battery cartridge?
No, do not short the battery cartridge:
- Do not touch the terminals with any conductive material.
- Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
- Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
Where should I store the tool and battery cartridge?
Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 ﾟ C (122 ﾟ F).
Should I incinerate the battery cartridge?
No, do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
What should I do if I drop or strike the battery?
Be careful not to drop or strike battery.
Is it okay to use a damaged battery?
No, do not use a damaged battery.
What should I do with the lithium-ion batteries when transporting them commercially?
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirement on packaging and labeling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
What should I do with the battery after it’s life cycle has ended?
Follow your local regulations relating to disposal of battery.
What batteries should I use?
Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
What are some tips for maintaining maximum battery life?
- Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
- Charge the battery cartridge with room temperature at 10 ﾟ C – 40 ﾟ C (50 ﾟ F – 104 ﾟ F). Let a hot battery cartridge cool down before charging it.
- Charge the battery cartridge if you do not use it for a long period (more than six months).
What should I always be sure of before adjusting or checking the function on the tool?
Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.
How do I remove the battery cartridge?
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.
How do I install the battery cartridge?
To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
What should I always install the battery cartridge until?
Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
What should I do if the battery cartridge does not slide in easily?
Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.
What happens if the tool is overloaded?
The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the switch trigger on the tool and stop the application that caused the tool to become overloaded. Then pull the switch trigger again to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the switch trigger again.
What happens if there is a low battery voltage?
The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery.
How do I indicate the remaining battery capacity?
Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for few seconds.
What should I always check to see before installing the battery cartridge into the tool?
Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
How do I start the tool?
To start the tool, press the trigger-lock button from B side and pull the switch trigger. Release the switch trigger to stop. After use, always press in the trigger-lock button from A side.
How do I light up the lamp?
Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out just after releasing the trigger.
What should I not do to the lamp?
Do not apply impact to the lamp, which may cause damage or shorted service time to it.
How do I clean the lamp?
Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.
What should I not use to clean the lamp?
Do not use thinner or gasoline to clean the lamp. Such solvents may damage it.
What should I always be sure of before carrying out any work on the tool?
Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
What should I wipe off before installing the blade?
Oil on the blade can cause the blade to slip or come off unexpectedly. Wipe off all excess oil with a cloth before installing the blade.
What should I always wear when handling the blade?
Always wear protective gloves when handling the blade.
What should I be cautious of when handling the blade?
Use caution when handling the blade to avoid cut by the sharp edge of the blade teeth.
Where should I keep my body when checking the blade movement?
Keep your body away from the blade area when checking the blade movement.
What direction should I point the tool when turning the blade tightening lever clockwise to release the tension on the blade?
When turning the blade tightening lever clockwise to release the tension on the blade, point the tool downward because the blade may come off unexpectedly.
How do I install the blade?
- Turn the blade tightening lever clockwise until it stops to loosen the wheel.
- Match the direction of the arrows on the blade and on the wheels.
- Insert the non-serrated side of the blade into the upper holder and lower holder. Make sure the blade in both upper and lower holder touches to the bottom bearings.
- With pressing the middle part of the blade, position the blade around one wheel. Moving the wheel to A side makes it easier to do so.
- Position the blade on another wheel similarly.
- Position the edge of the blade on rubber tire.
- Hold the blade in place and turn the blade-tightening lever counterclockwise until it stops. This places proper tension on the blade.
Make sure that the blade is correctly positioned around the wheels. Start and stop the tool two or three times to make sure that the blade runs properly on the wheels. To remove the blade, follow the installation procedure in reverse.
How do I adjust the stopper plate position?
In the ordinary operation, protrude the stopper plate to the A side fully. When the stopper plate strikes against the obstacles like a wall or the like at the finishing of a cut, loosen two screws and slide it to the B side in the figure. After sliding the stopper plate, secure it by tightening two screws firmly.
How do I install the hook?
To install the hook, set the hook alongside the groove and tighten it with two screws.
Where should I hold the tool?
Always hold front and rear handle. Never hold the tool body or guards. Hands may slip from these locations and contact blade. Contact with the blade may result in personal injury.
What should I make sure of when turning on or off the tool or when cutting?
Make sure to hold the tool firmly when turning on or off the tool or when cutting. Otherwise the tool may fall and cause personal injury.
How do I properly cut with the tool?
- For stable cut, always keep at least two teeth in the cut.
- Select the proper cutting position for your workpiece by referring to the figure.
- Hold the tool with both hands as shown in the figure. Before turning on the tool, always make sure that the stopper plate contacts the workpiece and the blade is clear of the workpiece. Turn the tool on and wait until the blade attains full speed. Gently lower the blade into the cut. The weight of the tool or slightly pressing the tool will supply adequate pressure for the cutting. Do not force the tool. As you reach the end of a cut, release pressure and lift it slightly so that it will not fall against the workpiece.
- Applying excessive pressure to the tool or twisting of the blade may cause bevel cutting or damage to the blade.
- When not using the tool for a long period of time, remove the blade from the tool.
- If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
What should I never use as a cutting lubricant?
Never use cutting oil or apply excessive amount of wax to the blade. It may cause the blade to slip or come off unexpectedly.
When should I not use any cutting wax?
When cutting cast iron, do not use any cutting wax.
When should I use Makita cutting wax as a cutting lubricant?
When cutting metals, use Makita cutting wax as a cutting lubricant. To apply the cutting wax to the blade teeth, remove a cap of the cutting wax, start the tool and cut into the cutting wax as shown in the figure.
What should I always be sure of before attempting to perform inspection or maintenance?
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
What should I never use to clean the tool?
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
How do I clean wax and chips from the tires?
Wax and chips on the tires may cause the blade to slip and come off unexpectedly. Use a dry cloth to remove wax and chips from the tires.
What should I remove from the tool after use?
After use, remove wax, chips and dust from the tool, wheel tires and blade.
When should I replace the tires on wheels?
Replace the tires when the blade slips or does not track properly because of badly worn tires.
Who should perform repairs, maintenance, or adjustments to maintain product safety and reliability?
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
What accessories or attachments are recommended for use?
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
- Makita genuine battery and charger
- Band saw blades
- Hex wrench 4
- Cutting wax
- Hook
- Wheel cover
How do I open the wheel cover?
When opening the wheel cover, open and release both the hooks simultaneously. Opening only one hook may cause crack on the wheel cover.
CLICK HERE TO DOWNLOAD MAKITA DPB181 (01) PDF MANUAL