MAJORITY P500 (01) PDF Document

The box contents include:

A. MAJORITY P500 Party Speaker

B. Wired Microphone

C. Wireless Microphone

D. Tripod Stand

E. Remote Control

F. USB Type-C Charging Cable

G. User Manual

At the lowest extension, the MAJORITY P500 tripod is 43.5cm high and at maximum extension is 76cm high.

Step 1: Once removed from the box, unfold the bottom three legs. Keep it stable so the tripod won’t wobble easily.

Step 2: Loosen the fixing screws and adjust the tripod to the appropriate height.

Step 3: Tighten the fixing screws. Once secured, position your speaker and affix on the tripod stand using the hole and screw located on the speaker.

Insert the USB Type-C cable at the back of the unit into the charging port (DC5V), and then connect with a plug to the mains for charging. The charging LED screen will light up red. It takes up to 6 hours to process a full charge course of the internal battery. Once fully charged, the red LED light will switch off.

It is recommended to process a full charge course when not in use for longer battery life.

Once fully charged, the speaker can be used on battery power for up to 6 hours. Please note that the playtime may vary based on the volume level and lighting modes usage while playing on battery power.

Rotate the ‘Power ON/OFF’ knob to the right to switch the power on and increase the volume as per your preferences. Rotate the ‘Power ON/OFF’ knob to the left to decrease the volume and switch off the party speaker.

The ‘TWS’ function can only be used when using two MAJORITY P500 Party Speakers. Note that each package only contains one speaker.

1. Ensure that both speakers are powered on and not paired individually with other devices via Bluetooth.

2. Press the ‘TWS’ button twice on one of these speakers and both will wirelessly connect with each other.

3. Once both MAJORITY P500 speakers are paired, switch on Bluetooth connectivity on your phone, and then search for ‘Majority P500’. Select and pair with the speakers.

4. To disconnect, press the ‘TWS’ button twice on one of the party speakers.

1. Press the ‘MODE’ button on the unit or on the remote control repeatedly to change the speaker mode to Bluetooth. The text ‘BT’ will be displayed on the screen indicating the mode.

2. Activate Bluetooth on your device and search for ‘Majority P500’. Select the speaker and pair with your device.

3. Once connected, you can start playing audio from your device.

Note: The MAJORITY P500 cannot be paired with Bluetooth earbuds or earphones.

Press the ‘Mode’ button on the remote control repeatedly to change into USB Mode. The display screen will show ‘USB’. Insert a USB stick into the USB Playback port and the MAJORITY P500 will automatically start playing audio.

The USB stick should be up to 32GB and must be formatted in FAT32. Supported audio formats are MP3 or WAV. Note that the USB port is for playback only and cannot be used to connect with other devices.

Press the ‘Mode’ button on the remote control or on the unit repeatedly to change the speaker mode to ‘TF’. The text ‘TF’ will be displayed on the screen. Insert the Micro SD Card into its slot at the back of the speaker, and the MAJORITY P500 will start playing audio.

The card should be up to 32GB and formatted in FAT32. Supported formats are MP3 or WAV.

1. Press the ‘MODE’ button on the unit or remote repeatedly to change to ‘FM Radio’. The text ‘FM’ will display on the screen.

2. Press and hold the ‘Play/Pause/TWS’ button on the unit or the Play/Pause button on the remote for 2-3 seconds to start an automatic scan for available FM stations.

3. Once completed, the stations will be saved automatically, and the speaker will play the first station found.

4. Press the ‘PREVIOUS’ or ‘NEXT’ buttons to navigate through the stored stations.

Insert one end of a 3.5mm AUX audio cable (not included) into the AUX-In port of the party speaker, and the other end into your audio source device’s AUX output port. Change the Mode to AUX-In Mode by pressing the ‘Mode’ button until the LCD screen displays ‘AUX’.

To change the lighting modes, you must press and hold the Mode/Lightning button (Ref.3) for 2-3 seconds.

Power on the MAJORITY P500 speaker, and then press the ‘Power On/Off’ button on the microphone. The wireless microphone will automatically connect with the party speaker.

The wireless microphone features a “Magic Voice” button that changes the voice to male, female, baby, or normal voice.

Insert the wired cable end into the MIC In port at the back of the speaker. Power on the MAJORITY P500 speaker, and then press the ‘Power On/Off’ button on the microphone.

Note: The wired and wireless microphones can be used at the same time or individually.

The remote control functions are as follows:

Standby: Puts the speaker in Sleeping Mode or turns it on.

Stop: Stops playing.

Volume +: Increases volume.

Previous: Skips to the previous song or FM station.

Repeat: Repeats one track or all tracks (USB/Micro SD Mode only).

Numerical Keys: Directly access MP3 tracks.

Mode: Long press to change modes (Bluetooth, FM, AUX, USB, SD Card).

Mute: Turns sound on or off.

Next: Skips to the next song or FM station.

Play/Pause: Plays or pauses audio.

Volume -: Decreases volume.

EQ: Selects sound styles (NORMAL, POP, ROCK, JAZZ, CLASSIC, COUNTRY).

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not clean the apparatus near or with water.

6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.

9. Protect the power from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Only use accessories specified by the manufacturer.

11. Unplug this apparatus during light storms or when unused for long periods of time.

12. Refer all servicing to qualified service personnel.

13. No naked flame sources, such as a lit candle should be placed on the apparatus.

14. Dispose of used electrical products and batteries safely according to your local authority and regulations.

Additional Warnings: The apparatus shall not be exposed to dripping, splashing or objects filled with water. The main plug is used to disconnect the device. Battery shall not be exposed to excessive heat.