LYNGDORF AUDIO LS-1000 RIGHT (01) PDF Document

The inventory includes the LYNGDORF AUDIO LS-1000 RIGHT unit itself, side brackets for securing individual speaker units to each other (these are attached to each side prior to shipping), top and base brackets for securing the top and bottom speaker units in each stack, and the necessary mounting screws for the top, base, and side brackets.

For proper mounting of a LYNGDORF AUDIO LS-1000 RIGHT loudspeaker stack, you must create a rectangular cutout in the wall based on specific dimensional requirements.

The minimum depth required for a 4 x LYNGDORF AUDIO LS-1000 RIGHT stack, including top and base brackets, is 95 mm or 3.7 in.

The minimum height required for a single LYNGDORF AUDIO LS-1000 RIGHT unit, including top and base brackets, is 585 mm or 23 in.

The minimum width required for the LYNGDORF AUDIO LS-1000 RIGHT, including top and base brackets, is 290 mm or 11.4 in.

The minimum height required for a 4 x LYNGDORF AUDIO LS-1000 RIGHT stack is 2085 mm or 85 in.

For cable runs up to 16m or 50ft, the recommended minimum specification is AWG 14/2 or 2-lead 2mm2.

For cable runs of 16m or 50ft and up, the recommended minimum specification is AWG 12/2 or 2-lead 3.5mm2.

The recommended maximum cable specification is Double AWG 10/2 or 2-lead 5mm2.

You should allow a minimum of 50cm of extra cable for connecting the cable to the speaker binding posts before the speaker is placed inside the wall or ceiling.

Arrange the individual units on the floor, ready to combine them into a stack. Place the loudspeakers with the back side down on the floor, preferably close to the wall cutout. Ensure the floor is covered with fabric, such as carpeting, to avoid scratching the loudspeakers.

Using a torx 30 type screwdriver, remove the screws securing the pre-installed POM thermoplastic side brackets to the loudspeakers, and keep the brackets and screws close at hand.

Using the screws you removed, secure the side brackets to the stack. The bracket must bridge two loudspeakers, allowing it to be affixed to each loudspeaker with two screws. Insert the screws into all four holes and tighten them by hand until the head of each screw protrudes 1-2 mm, then tighten the screws fully with a torx 30 screwdriver.

If you mount the bracket one screw at a time, the last screw may not be fully aligned with the hole. Tightening it may result in the screw thread being stripped, which renders the screw useless and leads to an unstable loudspeaker stack.

Use a torx 30 screwdriver and the supplied black M6x30 screws to secure the dedicated top and bottom brackets to the loudspeakers in their respective stacks.

Connect and tighten the speaker cables using a small, slotted screwdriver to the base plate of the first speaker. Ensure the cable ends are securely tightened and no bare wire is standing out. Other elements in the stack connect through the plug-in terminals.

Mount the top bracket to the top loudspeaker using a torx 30 screwdriver and the supplied black M6x16 screws. Align the stack with the wall opening and ensure it stands leveled and steady by adjusting the base feet. Then, mount the top wall bracket to the top beam of the wall cutout using a torx 30 screwdriver and the supplied C6x30 screws.

The purpose of the top wall bracket is to stabilize the stack at the beam, and it is not intended to bear the weight of the speaker stack.

For safety, do not attempt to raise the stack by yourself. There should be one person involved in lifting a loudspeaker stack for every two loudspeaker units in the stack; therefore, a stack of 4 units requires at least two people to lift.

The LYNGDORF AUDIO LS-1000 RIGHT features an MDF enclosure. The frequency range is 100 to 20,000 Hz (-3 dB) for four modules, with frequency extension down to 50 Hz depending on EQ.

For four modules, the nominal impedance is 4 Ohm (16 Ohm per module) and the power handling is 300 W (IEC).

For four modules, the maximum SPL is 120 dB and the crossover point is 1.8 kHz.

The sensitivity is 98 dB (2.83 V/1 m) for four modules.

The LYNGDORF AUDIO LS-1000 RIGHT features 8 pieces of 1-inch soft dome tweeters.

It uses 4 pieces of 115 mm midrange drivers, with a 25 mm voice coil, aluminum cone, and vented magnet.

The LYNGDORF AUDIO LS-1000 RIGHT weighs 9.9 kg or 21.8 lb and has a matte black finish.

The LYNGDORF AUDIO LS-1000 RIGHT is a 2-way line source, closed loudspeaker.

The LYNGDORF AUDIO LS-1000 RIGHT uses screw terminals for connections.

Yes, the LYNGDORF AUDIO LS-1000 RIGHT is designed for in-wall mounting.

The dimensions (W x H x D) are 280 x 500 x 85 mm or 11 x 19.7 x 3.35 inches, plus mounting.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including any interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

Contact both the shipper and your local representative immediately if the unit bears any sign of damage from mishandling. It is recommended that you save your original packing materials.

Yes, it is recommended that you save your original packing materials, as it may be necessary to return the equipment for repair, and shipping without original packing could cause damage and potentially void the warranty.

The minimum depth required for the LYNGDORF AUDIO LS-1000 RIGHT is 95 mm or 3.7 in.

The stack must stand firmly on the ground, leveled by adjusting the base feet, and must be stabilized at the top beam using the top wall bracket.

No, the purpose of the top wall bracket is to stabilize the stack at the beam, and it is not meant to bear its weight.

The top bracket is mounted to the top loudspeaker using the supplied black M6x16 screws.

The top wall bracket should be mounted to the top beam using the supplied C6x30 screws.

While the first speaker connects to the speaker cables via its base plate, other LYNGDORF AUDIO LS-1000 RIGHT elements in the stack connect through plug-in terminals.

A torx 30 screwdriver is required for the bracket screws.

A small, slotted screwdriver is used to connect and tighten the speaker cables to the base plate.

The cutout for a 4 x LYNGDORF AUDIO LS-1000 RIGHT stack must accommodate a height of 2085 mm or 85 inches and a width of 290 mm or 11.4 inches.

Make sure the cable ends are securely tightened and no bare wire is standing out.

Yes, ensure the stack stands leveled and steady by adjusting the base feet after aligning it with the wall opening.

The floor should be covered with fabric, such as carpeting, to avoid scratching the loudspeakers while they are being prepared for stacking.

Yes, the inventory includes dedicated top and base brackets for securing the top and bottom speaker units in each stack.

The side brackets are made of POM thermoplastic.

Place the loudspeakers in order, with the bottom loudspeaker in the stack closest to the bottom edge of the wall cutout. This facilitates easy mounting as the stack can be tilted directly into place.

Yes, please dispose of any waste materials in accordance with your local recycling regulations, as products marked with the icon of the crossed-out waste receptacle are subject to the WEEE Directive.

Yes, the products and accessories comply with parts 15 and 68 of the FCC rules.

Each additional LYNGDORF AUDIO LS-1000 RIGHT unit requires 500 mm or 19.7 in of height and 95 mm or 3.7 in of depth.

The supplied black M6x30 screws are used to secure the dedicated top and bottom brackets to the loudspeakers.