LLOYTRON MIP SYSTEM 3 B7835 (01) PDF Document

The LLOYTRON MIP SYSTEM 3 B7835 Motion Sensor Transmitter is battery-operated and has a wireless range of 175m.

Operating Voltage: 4.5v DC

Batteries: Requires 3x AAA 1.5v alkaline batteries. It is recommended to use Duracell batteries. Do not use Carbon Zinc or Rechargeable batteries.

PIR Range: 5m (approx.)

PIR Angle: 110° Horizontal, 45° Vertical

Rating: The PIR Sensor is IP44 rated, making it splashproof.

Operating Frequency: 433.33Mhz

Inside the box, you will find:

1x PIR Motion Sensor Transmitter

Screws and Stick Pad

1x Operating Manual

Please follow these safety instructions:

Read all instructions carefully.

For Household use only.

The Motion Sensor is splashproof and can be used outdoors but should be protected or covered from a large deluge of water.

To prevent the risk of electric shock, do not submerge any part of this appliance in water.

This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of this product by a person responsible for their safety.

Children should be supervised to ensure they do not play with this appliance.

Cleaning and user maintenance should not be made by children.

Never let children push anything into holes or slots in the cabinet – this could result in an electric shock.

Should you find the range sensitivity or quality of sound deteriorating, replace old batteries with new ones as soon as possible. The use of long-life Alkaline batteries is recommended.

Dispose of old batteries carefully and in accordance with local government guidelines.

Do not use a receiver outside or in damp conditions.

Do not use rechargeable batteries.

Do not mix old and new batteries or different chemistry of batteries.

Do not use for any purposes other than the intended use.

Do not use if damaged in any way.

Do not dismantle. There are no serviceable parts.

The LLOYTRON MIP SYSTEM 3 B7835 has an unobstructed operating distance of 200 meters, but local conditions can reduce this distance. The number of walls, doors, and the material they are made of will affect the signal. Metal door frames and other factors may also interfere with the signal.

The range decreases when obstructed by the following materials, in order of severity:

1. Metal

2. Brick

3. Wood

Note: For easy programming, keep the Motion Sensor Transmitter and chime unit close together whilst linking/programming. This saves time and effort. You will be required to link/programme this new accessory to your existing MIP System™ Chime Units. It is advisable to link before you mount the Motion Sensor Module.

1. On each chime unit, press and hold the chime selection button or chime replay button for 10 seconds. An audible beep beep will be heard. The chime unit is now in a waiting mode for 15 seconds to link the transmitter.

2. Using the switch at the rear of the sensor unit after the batteries have been installed, move the switch to the ON position. An audible BEEP will be heard from the chime unit to advise the Sensor transmitter has been linked successfully.

3. To exit programming mode, press the chime replay button on the chime unit again or wait several seconds until a beep beep is heard. The link process has now completed.

4. SWITCH the Sensor OFF and then back ON to trigger the Chime Unit sound.

If multiple receivers are being used, then each receiver must be programmed to the corresponding bell push individually. Also refer to the individual device manual for accessories before linking.

The PIR Motion Sensor module will activate any linked door chime receiver every time it detects movement within a 5m range. The unit is splashproof and suitable for use outside. Please note that birds, pets, and other animals may also trigger the device.

1. Pry open the battery compartment at the back of the sensor.

2. Insert 3x AAA batteries observing the correct polarity as indicated on the sensor and the battery.

3. If required, change the red switch settings as described in “Different Bell Push Different Tunes”. If unsure, leave on the default setting.

4. If mounting with screws, screw through the holes provided.

5. If not mounting with screws, use the self-adhesive pad supplied and affix so the PIR Sensor is pointing towards the area required to monitor.

WARNING: DO NOT PLACE IN DIRECT SUNLIGHT. This may cause premature activations.

Inside the LLOYTRON MIP SYSTEM 3 B7835 transmitter casing, you will see a red block with two micro switches. You can change the settings to select one of four consecutive sounds on a compatible chime unit. Once a default chime sound has been chosen on the chime unit, the next three consecutive sounds can be selected on different transmitters.

1ST CHIME SOUND (DEFAULT SETTING)

This setting is compatible with ALL generations of MIP System™ Door Chimes. To select the default sound chosen on the paired chime unit, position both micro switches (1 and 2) to the DOWN (0) position.

2ND CHIME SOUND

To set the transmitter to play the 2nd chime sound on the paired chime unit, position micro switch 1 to the UP (1) position and micro switch 2 to the DOWN (0) position.

3RD CHIME SOUND

To set the transmitter to play the 3rd chime sound on the paired chime unit, position micro switch 1 to the DOWN (0) position and micro switch 2 to the UP (1) position.

4TH CHIME SOUND

To set the transmitter to play the 4th chime sound on the paired chime unit, position both micro switches (1 and 2) to the UP (1) position.

WARNING: The 2nd, 3rd, and 4th chime sound settings are NOT compatible with non-MIP products or first generation MIP System™ 1. They are only compatible with the Second generation MIP System 2™ and Third generation MIP System3™ Door Chimes. If your system is not compatible, leave the transmitter on the Default setting; otherwise, no activation will be made and it will not sound on the chime unit.

On the rear or side of every product is a Rating Plate. This plate will advise a batch number, and/or it will state MIP System 2™ or MIP System 3™.

Products prior to batch 24305 are not compatible with MIP System™.

1st Generation MIP: Batch numbers 24305 to 31838

2nd Generation MIP (MIP System 2™): Batch numbers 31839 to 33178

3rd Generation MIP (MIP System 3™): Batch numbers from 33179+

If your LLOYTRON MIP SYSTEM 3 B7835 chime unit is activating every few minutes, check that the motion sensor has not been broken, is not sticking, or that there is no water inside the unit.

First, check that the switch settings inside the bell push or transmitter are on default. If the issue persists, try to re-link the bell push to the receiver by following the instructions in the “Link / Programme Devices” section.

Ensure the mains switch for the chime unit is plugged in and switched on at the wall.

Wipe the accessory with a clean soft lint-free cloth to remove dirt and dust.

Do not use abrasives, detergent, or solvent on any surface.

Disposal of Electrical and Electronic Equipment:

Do not dispose of this product with household waste. For proper treatment, recovery, and recycling, please take this product to the appropriate waste collection point. If you are unsure where this may be, please contact your local authority. Improper disposal may be harmful to the environment.

Product End of Life and Battery Disposal:

The battery contains substances that may pollute the environment. At the end of life for the product, always remove the battery and separate it before you discard the product at your local waste collection point. Both the battery and the product should be disposed of separately.

If you have trouble removing the battery, you should contact a qualified technician or authorized service center.