LG XHS-55TAC (01) PDF MANUAL

FREE ENGLISH LG XHS-55TAC (01) PDF USER GUIDE

FREE ENGLISH LG XHS-55TAC (01) PDF USER MANUAL

FREE ENGLISH LG XHS-55TAC (01) PDF OWNER GUIDE

FREE ENGLISH LG XHS-55TAC (01) PDF OWNER MANUAL

FREE ENGLISH LG XHS-55TAC (01) PDF REFERENCE GUIDE

FREE ENGLISH LG XHS-55TAC (01) PDF INSTRUCTION GUIDE

FREE ENGLISH LG XHS-55TAC (01) PDF REFERENCE MANUAL

FREE ENGLISH LG XHS-55TAC (01) PDF INSTRUCTION MANUAL

FREE ENGLISH LG XHS-55TAC (01) PDF OPERATING INSTRUCTIONS

CLICK HERE TO DOWNLOAD LG XHS-55TAC (01) PDF MANUAL

If this is not the document you want for this product, click here to see if we have any other documents for this product.

LG XHS-55TAC (01) PDF SUMMARY:

What safety precautions should I take when using the LG DVD Karaoke Receiver?

To reduce the risk of electric shock, do not remove the cover or back of the unit, as there are no user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash symbol alerts the user to the presence of uninsulated dangerous voltage within the product’s enclosure, which may cause electric shock. The exclamation point alerts the user to important operating and maintenance instructions in the manual. To prevent fire or electric shock, do not expose the product to rain or moisture. Do not install the equipment in a confined space. The apparatus should not be exposed to water, and objects filled with liquids should not be placed on it. Performing controls, adjustments, or procedures other than those specified may result in hazardous radiation exposure. To prevent direct exposure to a laser beam, do not try to open the enclosure.

What should I do with my old appliance when disposing of it?

When the crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/96/EC. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or local authorities. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. For more detailed information about disposal, contact your city office, waste disposal service, or the shop where you purchased the product.

What types of discs are playable on the LG DVD Karaoke Receiver?

The LG DVD Karaoke Receiver can play DVD, Video CD (VCD), and Audio CD discs. It can also play DVD-RW, DVD+RW, SVCD, and CD-R or CD-RW discs that contain audio titles, MP3, WMA, JPEG, or DivX files. Some CD-R/RW (or DVD-RW, DVD+RW) discs cannot be played depending on the recording equipment or the disc itself. Do not attach any seal or label to either side of a disc and do not use irregularly shaped CDs.

What is the significance of regional codes on DVDs, and how does it affect playback on the DVD/CD receiver?

The DVD/CD Receiver is designed for playback of region “5” encoded DVD software. The region code on DVD labels indicates which type of player can play those discs. This unit can only play DVDs labeled “5” or “ALL”. If you try to play any other discs, the message “Check Regional Code” will appear on the TV screen. Some DVDs that have no region code label may still be subject to area restrictions and therefore not playable.

What should I do when playing DTS-encoded CDs?

When playing DTS-encoded CDs, excessive audio levels may be heard from the analog stereo output. To avoid possible damage to the audio system, turn down the volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the digital output of the unit.

What are the two types of Video CDs?

There are two types of Video CDs: Video CDs equipped with PBC (Version 2.0) and Video CDs not equipped with PBC (Version 1.1). PBC (Playback control) functions allow you to interact with the system via menus, search functions, or other computer-like operations. Video CDs not equipped with PBC are operated in the same way as audio CDs, allowing playback of video pictures as well as sound, but they are not equipped with PBC.

What precautions should I take when handling and setting up the unit?

When shipping the unit, use the original shipping carton and packing materials for maximum protection. When setting up the unit, position it away from a nearby TV, VCR, or radio, or turn it off after removing the disc if the picture and sound are disturbed during playback. Do not use volatile liquids, such as insecticide spray, near the unit and do not leave rubber or plastic products in contact with the unit for a long period of time.

How do I clean the LG DVD Karaoke Receiver?

To clean the cabinet, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzene, or thinner, as these might damage the surface of the unit. Regular inspection and maintenance are recommended after every 1,000 hours of use.

How should I handle and store discs?

Do not touch the playback side of the disc and hold the disc by the edges to avoid fingerprints. Do not stick paper or tape on the disc. After playing, store the disc in its case and do not expose it to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sunlight.

How do I clean discs?

Clean the disc with a clean cloth, wiping from the center outwards. Do not use strong solvents such as alcohol, benzene, thinner, commercially available cleaners, or anti-static spray intended for vinyl records.

What do the disc symbols mean in the instructions?

A section whose title has one of the following symbols is applicable only to the disc represented by the symbol:

  • DVD and finalized DVD±R/RW
  • Video CDs with the PBC (playback control) function
  • Video CDs without the PBC (playback control) function
  • Audio CDs
  • MP3 disc
  • WMA disc
  • JPEG disc
  • DivX disc

What are the functions of the front panel connectors and buttons?

  • MIC 1/MIC 2: Connect a microphone to MIC 1 or MIC 2 or to both sockets.
  • USB host: Connect to a USB port of multimedia (USB memory etc.).
  • STANDBY/ON: Lights red when the receiver is in Standby mode (off).
  • DISC Tray
  • FUNCTION/PLAY: Press and hold down this button about 3 seconds, then press repeatedly to select other function.
  • VOLUME controller
  • DISPLAY Window
  • OPEN/CLOSE button
  • Remote sensor
  • MONO/STEREO/ PAUSE/STEP
  • STOP
  • SPEAKER connectors
  • TUNING(-/+)/SKIP(-/+) KEY CONTROL(b)/(#) buttons

What are the functions of the rear panel connectors?

  • Power Cord
  • FM Antenna connector
  • OUTPUT (TO TV) EURO AV socket: Connect to a TV with SCART jack.
  • AM Loop Antenna connectors
  • S-VIDEO OUT connector
  • MONITOR OUT connector
  • COMPONENT VIDEO OUT terminals: Connect to a TV with Y Pb Pr inputs.
  • AV IN AUDIO Input (L/R)/VIDEO IN connectors
  • VIDEO OUTPUT SELECTOR Switch: Select either COMPONENT VIDEO OUTPUT or SCART signal of EURO AV terminal depending on how you connected the DVD/CD Receiver to the TV.

What should I avoid touching on the rear panel?

Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

What are the functions of the remote control buttons?

  • POWER: Turns the DVD/CD Receiver on or off.
  • DVD/KARAOKE: Selects the output source (CD/DVD) or accesses or removes KARAOKE.
  • BAND: Selects the System’s tuner (FM and AM bands).
  • 0-9 numerical buttons: Select a service, programme number directly or select numbered options in a menu.
  • XTS pro: To enjoy more natural and realistic sound.
  • XTS: To enjoy great sound effect.
  • AUDIO: Selects an audio language (DVD) or an audio channel (CD).
  • MALE: To sing a song of MAN’s.
  • SETUP: Accesses or removes setup menu.
  • MENU: Accesses the menu on a DVD disc.
  • TEMPO(-/+): To play fast or slow. (LG karaoke disc only).
  • SCAN(◄◄/►►): Search backward or forward.
  • SLOW-/+(◄I/I►): Reverse/ Forward slow playback.
  • b – KEY CON. – #: Adjust a vocal range (LG karaoke disc only).
  • REVERSE SKIP(l+II): Search backward*/go to beginning of current chapter or track or go to previous chapter or track.
  • FORWARD SKIP(…): Search forward*/go to next chapter or track.
  • PROG.: Accesses or removes Program menu.
  • MEMO.: Enter a radio station’s frequency into the tuner.
  • CLEAR: Removes a track number on the program menu or a mark on the MARKER SEARCH menu.
  • REPEAT: Repeat chapter, track, title, all.
  • REPEAT A-B: Repeats sequence.
  • MIC VOL.(T / .&.): Adjusts microphone volume.
  • ECHO VOL.(T / .&.): Adjusts echo volume.
  • OPEN/CLOSE (6): Opens and closes the disc tray.
  • AUX: Selects input source.
  • TV: To control the TV (LG TV only).
  • SUBTITLE: Selects a subtitle language (DVD).
  • SHADOW: To highlight the song’s subtitle.
  • RETURN: To enjoy the multimedia files.
  • SOUND MODE: Selects the sound mode.
  • FEMALE: To sing a song of WOMEN’s.
  • DISPLAY: Accesses On-Screen display.
  • INPUT: Selects the TV’s source.
  • ◄/►/A/IT (left/right/up/down): Selects an option in the menu.
  • ENTER: Acknowledges the menu selection.
  • PR/CH(+/-) (.&./T): Select programme of TV or Radio.
  • TUN(-/+)(◄/►): To tune in the desired radio station.
  • TITLE: Displays the disc’s Title menu, if available.
  • VOLUME(+/-): To adjust speaker volume and TV volume.
  • ZOOM: Enlarges the DVD video image.
  • STOP(■): Stops playback.
  • PAUSE/STEP (II): Pause playback.
  • PLAY(►): Starts playback.
  • MUTE: Mute the speakers.
  • MARKER: Marks a point during playback.
  • SEARCH: Displays MARKER SEARCH menu.
  • SLEEP: Set the System to turn off automatically at a specified time.
  • DIMMER: Press to change brightness of the display window on the front panel during in power-on status.

What is the remote control operation range?

  • Distance: About 23 ft (7 m) from the front of the remote sensor
  • Angle: About 30° in each direction in front of the remote sensor

How do I install the remote control battery?

Remove the battery cover on the rear of the remote control, and insert two R03 (size AAA) batteries with O and C aligned correctly. Do not mix old and new batteries and never mix different types of batteries (standard, alkaline, etc.).

What should I consider when making TV connections?

Make one of the following connections, depending on the capabilities of your existing equipment. When using the COMPONENT VIDEO OUT jacks, set the VIDEO OUT SELECTOR switch to COMPONENT. When using the SCART jack, set the VIDEO OUT SELECTOR switch to SCART.

What are some tips for TV connections?

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD/CD Receiver. Refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections. Make sure the DVD/CD Receiver is connected directly to the TV and select the correct AV input on your TV. Do not connect your DVD/CD Receiver to TV via your VCR.

What types of TV connections can I use?

  • S-Video connection: Connect the S-VIDEO OUT jack on the DVD/CD Receiver to the S-VIDEO IN jack on the TV using the S-Video cable (S).
  • Video connection: Connect the MONITOR OUT jack from the DVD/CD Receiver to the VIDEO IN jack on the TV using the video cable supplied (V).
  • SCART connection: Connect the EURO AV OUTPUT (TO TV) socket on the DVD/CD Receiver to the corresponding in jacks on the TV using the scart cable (T).
  • Component Video (Color Stream®) connection: Connect the COMPONENT VIDEO OUT jacks from the DVD/CD Receiver to the corresponding in jacks on the TV using an Y Pb Pr cable ©.

What is Progressive Scan (ColorStream® pro) connection?

If your television is a high-definition or “digital ready” television, you may take advantage of the DVD/CD Receiver’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD/CD Receiver. Connect the COMPONENT VIDEO OUT jacks from the DVD/CD Receiver to the corresponding in jacks on the TV using an optional Y Pb Pr cable ©.

How do I set up progressive scan?

  • Set the Progressive to “On” on the Setup menu for progressive signal.
  • Set the progressive to “Off” by removing any disc from the unit and close the disc tray. See that “no disc” is displayed on the display window. Then, press STOP and hold it for five seconds before releasing it.
  • Progressive scan does not work with the analog video connections (yellow VIDEO OUT jack) or S-VIDEO connection.

How do I connect optional equipment?

  1. Connect a VCR to the AV IN connectors.
  2. Connect the USB port of a USB Memory (or MP3 player, etc.) to the USB HOST on the front of the unit.

If the audio format of the digital output does not match the capabilities of your DVD/CD Receiver, the receiver will produce a strong, distorted sound or no sound at all. The DivX files in your memory card will not be able to be play.

How do I connect the FM/AM aerial for listening to the radio?

Connect the supplied FM/AM aerial for listening to the radio. Connect the AM Loop aerial to the AM aerial connector and connect the FM Wire aerial to the FM aerial connector. To prevent noise pickup, keep the AM Loop aerial away from the DVD/CD Receiver and other components. Be sure to fully extend the FM wire aerial and keep it as horizontal as possible.

How do I assemble and connect the speakers?

The front and rear speakers are detached from the speaker stands. Connect the speaker cords and assemble the front and rear speakers from speaker stands as illustrated. Connect the speaker cords to the appropriate terminals on the bottom of each front and rear speaker. After connecting the speaker cords to the appropriate terminals on the bottom of each front and rear speaker and attach the front and rear speakers to the speaker stands. You cannot detach the speaker from the stand after assembling the front and rear speakers.

How do I connect the speaker system?

Connect the speakers using the supplied speaker cords. To obtain the best possible surround sound, adjust the speaker parameters (volume, distance, etc.). Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to -. If the cables are reversed, the sound will be distorted and will lack base. If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers. Do not remove the front cover of supplied speaker.

How should I position the speakers?

In the case of normal position use the 6 speakers (2 front speakers, centre speaker, 2 rear speakers and subwoofer). If you want to play the excellent bass sound, DTS digital surround or Dolby Digital surround, you should connect a subwoofer.

  • Front speakers: According to your listening position set up the speakers for equal distance and set up the interval between speakers to 45 degree.
  • Centre speaker: The centre speakers and front speakers are ideally the same height but normally place it above or below the television.
  • Rear speakers: Place left and right behind the listening area. These speakers recreate sound motion and atmosphere required for surround sound playback. For best results, do not install the rear speakers too far behind the listening position and install them at or above the level of the listener’s ears. In the case of a smaller room size, if the audience is near to the rear wall set the rear speakers opposite each other, and set the rear speakers above 60 – 90 cm than the listener’s ears.
  • Subwoofer: This can be placed in any front position.

How do I attach the ferrite core to the speaker cables?

  1. Press the stopper [a] of the ferrite core to open.
  2. Wind the cable once on the ferrite core.
  3. Close the ferrite core until it clicks.

Attach the ferrite core near the unit. The length here is short as much as possible.

What is DTS Digital Surround?

DTS Digital Surround allows you to enjoy 5.1 (or 6) discrete channels of high quality digital audio from DTS program sources such as discs, DVD and compact discs, etc. bearing the trademark. DTS Digital Surround delivers up to 6 channels of transparent audio and results in exceptional clarity throughout a true 360 degree sound field.

What is Dolby Digital surround format?

The Dolby Digital surround format lets you enjoy up to 5.1 channels of digital surround sound from a Dolby Digital program source. If you play DVDs with “ffi’ffl’I” mark, you can enjoy even better sound quality, greater spatial accuracy, and improved dynamic range.

What is Dolby Pro Logic 11?

Dolby Pro Logic 11 creates five full-bandwidth output channels from two-channel sources. This is done using an advanced, high-purity matrix surround decoder that extracts the spatial properties of the original recording without adding any new sounds or tonal colorations.

  • MOVIE mode: The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result is enhanced soundfield directionality that approaches the quality of discrete 5.1-channel sound.
  • MUSIC mode: The Music mode is for use with any stereo music recordings.
  • MATRIX mode: The Matrix mode is the same as the Music mode except that the directional enhancement logic is turned off. It may be used to enhance mono signals by making them seem “larger”.

What is BYPASS mode?

BYPASS Software with multichannel surround audio signals is played according to the way it was recorded.

How can I change the Digital Audio Output mode?

You can change the Digital Audio Output mode by pressing the AUDIO button on the remote control during playback. Although the DVD contents differ from disc to disc, the following explains the basic operation when this feature is used.

a) After you select 2 channel (For example ~·,~1 I or ~-,~1 1) by pressing AUDIO button, press SOUND button repeated ly.

b) After you select 5.1 channel (For example ~:.~1 I or ~;~~I) by pressing AUDIO button, press SOUND button.

How is sound mode changed when a Video CD is inserted?

Each time you press SOUND button, the sound mode of Video CD is changed on the display window in the following order: BYPASS ,STUDIO, CLUB_, HALL_, THEATER 1 ,CHURCH, PL II MOVIE_, PL II MUSIC _, PL II MTRX _, BYPASS … After you select the “Bypass” of sound mode by pressing SOUND button, press AUDIO button.

How is sound mode changed when a CD is inserted?

Each time you press SOUND button, the sound mode of Audio CD is changed on the display window in the fol­lowing order: BYPASS ,STUDIO, CLUB_, HALL_, THEATER 1 ,CHURCH, PL II MOVIE_, PL II MUSIC _, PL II MTRX _, BYPASS …

How can I identify the encoding format of program software?

  • Dolby Digital discs are labeled with the "”l’ll’l logo.
  • Dolby Surround encoded programs are labeled with the lP.!iw.J logo.
  • DTS Digital Surround discs are marked with DTS.

What happens when playing sound tracks with 96kHz sampling frequency?

When you play sound tracks with 96kHz sampling frequency, the output signals will be converted to 48kHz (sampling frequency).

What happens when I use a microphone except Karaoke function?

When you use a microphone except Karaoke function, you can’t enjoy 5.1 channel output. Only 2 channel sound will out by the influence of the microphone system.

How do I use the on-screen display?

  1. Press DISPLAY during playback.
  2. Press .&. / T to select an item. The selected item is highlighted.
  3. Press ◄ / ► to change the setting. You can also use the number buttons if appropriate (e.g. inputting the title number).

If no button is pressed for 10 seconds, the on­screen display disappears.

What are the initial settings that can be adjusted?

By using the Setup menu, you can make various adjustments to items such as picture and sound. You can also set a language for the subtitles and the Setup menu, among other things.

How do I display and exit the Menu?

Press SET UP to display the menu. A second press of SET UP will take you back to initial screen. To go to the next level: Press ► on the remote control. To go back to the previous level: Press ◄ on the remote control.

What are the steps for general operation in the setup menu?

  1. Press SET UP. The setup menu appears.
  2. Use _. / T to select the desired option then press ► to move to the second level.
  3. Use _. / T to select the second desired option then press ► to move to the third level.
  4. Use _. / T to select the desired setting then press ENTER to confirm your selection.
  5. Press SET UP or PLAY to exit the setup menu.

How do I select a language for the Setup menu and on-screen display?

Select a language for the Setup menu and on-screen display using the OSD option.

How do I select preferred languages for disc audio, subtitles, and menu?

Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. Original refers to the original language in which the disc was recorded. To select another language, press number buttons to enter the corresponding 4-digit number according to the language code list on page 34. If you enter the wrong language code, press CLEAR on the remote control.

How do I set the TV Aspect?

  • 4:3: Select when a standard 4:3 TV is connected.
  • 16:9: Select when a 16:9 wide TV is connected.

How do I set the Display Mode?

Display Mode setting works only when the TV Aspect mode is set to “4:3”.

  • Letterbox: Displays a wide picture with bands on the upper and lower portions of the screen.
  • Panscan: Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit.

What is Progressive Scan Video?

Progressive Scan Video provides the highest quality pictures with less flickering.

How do I set Progressive Scan?

If you are using the COMPONENT VIDEO OUT jacks, but are connecting the receiver to a standard (analog) television, set Progressive Scan to Off. If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On.

  1. Select “Progressive Scan” on the DISPLAY menu then press ►.
  2. Select “On” using the_./ T buttons.
  3. Press ENTER to confirm your selection. The confirm menu will appear.
  4. When the confirm menu appears on your screen Cancel is highlighted as default. Use the ◄ / ► buttons to highlight Enter.
  5. Pressing ENTER will set the DVD/CD Receiver to Progressive scan mode.

Progressive Scan will not be displayed in the setup menu when the VIDEO OUT SELECTOR switch is set at SCART position.

How do I reset the unit if I set Progressive Scan to On in error?

  1. Remove any disc from the unit and close the disc tray. See that “NO DISC” is displayed on the display window.
  2. Press and hold STOP ( ■) for five seconds then release it. The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analog TV or monitor.

How do I set the AUDIO options?

Each DVD disc has a variety of audio output options. Set the DVD/CD Receiver’s AUDIO options according to the type of audio system you use.

How do I set up the speakers?

Select speaker settings, including volume balance and distance, or test the speaker settings. Speaker settings are only active on the Analog Multi­Channel Output (See “Speaker Setting” page 25).

What is Dynamic Range Control (DRC)?

With the DVD format, you can hear a program’s sound-track in the most accurate and realistic presentation possible, thanks to digital audio technology. However, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). Set DRC to On for this effect.

The DRC function works only during playback of Dolby Digital recorded discs. The level of Dynamic Range Compression may differ depending on the DVD disc.

When should I set Vocal to On?

Set Vocal to On only when a multi-channel Karaoke DVD is playing. The karaoke channels on the disc will mix into a normal stereo sound.

How do I use the parental control feature?

The parental control feature allows you to block access to scenes below the rating you input, thereby preventing your children from being able to view material you believe is unsuitable.

  1. Select “Rating” on the LOCK menu, then press ►.
  2. To access the Rating, Password and Country Code features, you must input the 4-digit security code you created.
  3. Select a rating from 1 to 8 using the _. / T buttons.
  4. Press ENTER to confirm your rating selection, then press SET UP to exit the menu.

If you select unlock, parental control is not active and the disc plays in full.

How do I set or change the password (security code)?

  1. Select Password on the LOCK menu then press ►.
  2. Follow step 2 as shown left (Rating). "Change·· or "New·· is highlighted.
  3. Enter the new 4-digit code, then press ENTER.
  4. Press SET UP to exit the menu.

What should I do if I forget my security code?

If you forget your security code you can clear it using the following steps:

  1. Input the 6-digit number “210499” on the setup menu and the security code is cleared.
  2. Enter a new code as described above.

How do I set the Country Code?

  1. Select “Country Code” on the LOCK menu, then press ►.
  2. Follow step 2 as shown left (Rating).
  3. Select the first character using _. / T buttons.
  4. Shift the cursor using ► button and select the second character using _. / T buttons.
  5. Press ENTER to confirm your country code selection.

How do I set Playback Control (PBC)?

Set Playback Control (PBC) to On or Off.

  • On: Video CDs with PBC are played according to the PBC.
  • Off: Video CDs with PBC are played the same way as Audio CDs.

What is DivX® Registration?

You can show the DivX ORM (Digital Right Management) Registration code for your unit only. The Registration code is used for VOD (Video-On­Demand) service agent. You can purchase or rental an encrypt movie file.

What are the possible viewing limits for DivX VOD files?

  • Display the number which you can watch the file.
  • The rental has been expired.
  • Display the authorization error.

How do I play a DVD and Video CD?

  1. Turn on the TV and select the video input source connected to the DVD/CD Receiver.
  2. Turn on the audio system and select the input source connected to the DVD/CD Receiver.
  3. Press OPEN/CLOSE (6) to open the disc tray.
  4. Load your chosen disc in the tray, with the label facing up.
  5. Press OPEN/CLOSE (6) to close the tray.

What should I do if a menu screen is displayed?

The menu screen may be displayed first after loading a DVD or Video CD which contains a menu. Use the ◄l►/J;J’f" buttons to select the title/chapter you want to view, then press ENTER to start. Press TITLE or MENU to return to the menu screen. Use the number buttons to select the track you want to view and press RETURN to return to the menu screen.

Menu setting and the exact operating procedures for using the menu may differ depending on the disc. Follow the instructions on the each menu screen and you also may set PBC to Off under setup.

What should I do if Parental Control is set and the disc is not within the Rating settings?

The 4-digit code must be entered and/or the disc must be authorized (see “Parental Control”, on page 16).

How do I move to another TITLE?

When a disc has more than one title, you can move to another title as follows:

  1. Press DISP., then press the appropriate numbered button (0-9) to select a title number.

How do I move to another CHAPTER/TRACK?

When a title on a disc has more than one chapter or a disc has more than one track, you can move to another chapter/track as follows:

  1. Press …,… or ~ briefly during playback to select the next chapter/track or to return to the beginning of the current chapter/track.
  2. Press …,… twice briefly to step back to the previous chapter/track.
  3. To go directly to any chapter during DVD playback, press DISP., then press~ to select the chapter/track icon, then enter the chapter/track number using the numbered buttons (0-9).

How do I use Slow Motion?

  1. Press SLOW-/+ during pause. The receiver will enter SLOW mode.
  2. Use the SLOW-/+ to select the required speed: ◄I 1 /16, ◄I 1 /8, ◄I 1 /4 or ◄I 1 /2 (backward), or I► 1 /16, I► 1 /8, I► 1 /4 or I► 1 /2 (forward).
  3. To exit slow motion mode, press PLAY.

How do I use Still Picture and Frame-by-frame playback?

  1. Press PAUSE/STEP during playback. The DVD/CD Receiver will now go into PAUSE mode.
  2. You can advance the picture frame-by-frame by pressing PAUSE/STEP repeatedly on the remote control.

CLICK HERE TO DOWNLOAD LG XHS-55TAC (01) PDF MANUAL

Visitors also searched:

  1. LG XHS-55TAS (01) PDF MANUAL
  2. LG XHS-55TAW (01) PDF MANUAL

Leave comments, questions, reviews, tips, tricks, hacks or page errors below. Account not required.