LG T2108NT1G (01) PDF MANUAL

LG T2108NT1G (01) PDF SUMMARY:

How do I install the drain hose?

1. First, install the drain hose hook on the part of the outer drain hose component.
2. Put the drain hose clamp on the outer drain hose, insert the outer drain hose into the joint for it, and then clutch tightly with the drain hose hoop.
3. Completely slide the drain hose over the sewer and fix it with the hoop.

---

What should I do if I am using the common drain system?

Place the drain hose as shown in Figure 1.

---

What is the maximum drain height?

Drain height should be less than 10cm, otherwise, it will cause poor drainage. Do not stampede or squeeze the drain hose.

---

What should I do if the drain hose needs to be lengthened?

Purchase another drain hose. Ensure that the inner diameter is not less than 30mm and the length should not be less than 1.5m.

---

What should I do if I am using the Upper drain system?

Place the drain hose as shown in Figure 2.

---

What is the proper height for the drain hose when using the Upper drain system?

Ensure the drain hose is mounted at a suitable height, between 800 and 1200mm above the floor.

---

What should I avoid when using the Upper drain system?

Do not push the drain hose too far down the drain pipe or siphoning will occur.

---

How do I install the inlet hose if it is the one-touch type?

1. Untighten the upper connector screw.
2. Push the upper connector up until the rubber packing is in tight contact with the faucet. Then tighten the 4 screws.
3. Connect the water supply hose to the middle connector, pushing the plate down.
4. Make sure that the rubber seal is inside the hose connector.

---

How do I separate the water supply hose from the middle connector?

Shut off the faucet. Then pull the inlet hose down, pushing the plate down.

---

What should I do after connecting the water inlet hose?

1. Insert the power plug into the electrical socket.
2. Ensure the drain hose is mounted at the correct height.
3. Select a suitable location for the washer on a hard, even surface away from direct sunlight or heat sources, e.g. radiators, cooking appliances, etc.

---

What should I do if the floor is uneven?

Any floor unevenness may result in unstable working or abnormal noise. Please ensure the machine is level.

---

How do I install the inlet hose if it is the screw type?

1. Check the tap mouth. Let the taps mate with the skirtlike nut of the water inlet hose.
2. Pull the skirtlike nut of one end of the water inlet hose upwards, and then screw into the tap tightly.
3. Grasp the water inlet hose by hand and pull it downwards to see whether it is secured.
4. Screw the nut on the other end of the water inlet hose into the water inlet of the washing machine to the most.

---

What should I do after installing the water inlet hose?

After installing water inlet hose, do not start the washing machine in haste. Open the tap to create certain water pressure in the hose to check whether there is any leakage in the connector on both ends. If the pressure is too high, please shut the tap a little to avoid water leakage.

---

How do I install the cold and hot water inlet valves?

1. Inspect the threaded fitting on each hose and make sure there is a rubber seal in place on both ends.
2. Connect the water supply hoses to the hot and cold water faucets tightly by hand and then tighten another 2/3 turn with pliers.
3. Always run a gallon or two of water through each inlet hose to flush dirt, scale and other debris out of the water lines.
4. Attach the hot water line to the hot water inlet on the back of the washer. Attach the cold water line to the cold water inlet on the back of the washer. Tighten the fittings securely. Turn on both faucets all the way and check for leaks at both ends of the hoses.

---

Is it okay to overtighten the hoses?

Do not overtighten. Damage to the coupling can result and can damage the valves resulting in leaking and property damage.

---

What are the functions of the operation panel buttons?

• “ON/OFF” button:
  • Push the “ON/OFF” button to switch on the power.
  • To turn off the power, press the “ON/OFF” button.
  • If the “start /pause” button is not pushed within 10 minutes, the washing machine will automatically switch off the power.
• “Start/Pause” button:
  • After the power is switched on, press the “start/pause” button to start the machine.
  • During operation, press the “start/pause” button to pause the machine.
  • Press the “start/pause” button again to restart the machine.
• “Program” button:
  • The default setting is standard procedure.
  • According clothing material, quantity and dirty laundry degree, you can choose the right program. For details, see the special features.
• “Delay End” button:
  • The display shows the time remaining (in minutes) before the cycle will finish.
  • Push the “Delay End” button and the display will show the remaining time for the cycle to finish (in hours). The indicator flashes to indicate that the delay function is operating.
  • Delay start (2-24hr) option.
  • Delay time is the delay end till the wash finishes.
• “Water Level” button:
  • When turn on the power, the default setting is standard procedure. Press the “Start / Pause” button, will perform fuzzy function, the machine will automatically detect the amount of laundry, the water level is set automatically because of as the different degree of wet and dry cloth to determine the actual water level. When the choice is not the standard procedure, there is no fuzzy function, washing machine will display the default level.
  • When the machine is on power, press the [water level] key to select the water level, indicator shows from “1” to “8”, then the fuzzy function is canceled, you can select the appropriate level based on the amount of laundry. 1/2 water capacity indicator (flashes a file, lit for 2 files) and so on.
• “Process” button:
  • The button’s function is turn the right wash process for the clothes, the machine have several state for washing,such as soak, wash, rinse, spin, soak-wash,wash-rinse,rinse-spin, etc. User can choose the proper process to washing clothes.
  • After pressing the"ON/OFF" button, it can directly enter into the singer-spin program by pressing the “Process” button for 3 seconds.
• “Child Lock” function:
  • After washing machine start up, the machine is running, and if necessary, you can simultaneously press the [Delay End] + [Program] key three seconds or more to start the “child lock” function, beep issue “Didi, Didi” twice, under the child lock, any key is invalid, when any button is touched at this time, the machine will issue an invalid beep.
  • Lift: Press the [Delay End] + [Program] key about three seconds to cancel child lock, beep issue “Didi, Didi” twice, lifting the child lock, key functional recovery. When the program ends, or failure alarm error child lock is automatically released.

---

What are the available programs?

	Properties and Uses		Properties and Uses
Mixed Fabric	Washing the Mixed fabrics laundry.	Curtain	This program can apply for washing heavy fabrics such as curtain, blankets.
Normal	Strong ability to clean wide adapt-ability, can be applied to the use of spring,autumn, winter, to fast formain washing.cotton and linen fabric.	Baby Care	Independent wash procedures, suitable for baby’s clothes.
Delicates	Delicate items that are machine washable.	Tub Clean	Washing machine can automatically clean the dirt on the drum during the washing.
Quick Wash	Small load of lightly soiled laundry .	Tub Dry	Drying the inner and outer tub to avoid the growth of mildew.

---

What should I do before washing?

1. Check if the laundry has any special washing instructions.
2. Clear the pockets. Take out loose items such as coins, sand, hairpins, etc.
3. Tie any long strips, fasten buttons, and close zippers.
4. When the machine is running buttons may cause noise. To reduce the noise turn clothes inside out or place them in a laundry bags.

---

What notices should I take note of before washing?

• Check if the laundry is suitable for machine washing.
• Divide the laundry into color fast and non-colour fast items.
• Place items that do not absorb water easily into the water by hand.
• For heavily soiled items, please first remove loose dirt, then apply detergent directly to the stain before washing.
• For those items that may get lint or are furry or fluffy, please turn them inside out before washing.
• Do not put laundry polluted by chemicals into the washing machine.

---

What are the steps to operate the washing machine?

1. Connect the water resource and open the faucet.
2. Connect the power.
3. Place the upper drain hose as in the figure.
4. Open the lid, put in clothes and a suitable amount of washing powder. Close the lid.
5. Press the “ON/OFF” button.
6. Depending on your needs, select the necessary procedures to personalize.
7. Press the “start/pause” button.

---

What happens when the program has finished?

• When the machine stops, the buzzer will buzz continuously for 6 times and the power will be automatically cut off.
• Turn off the water tap.
• Pull out the power plug for safety.

---

What should I do to guarantee my safety?

Please check if the power point has been earthed before using to guarantee your safety.

---

What happens if the door is opened when the machine is running?

Close the lid of the door when the machine is running, otherwise, it will automatically stop working during the spin process and send out an abnormal warning.

---

Will the washer work if the water doesn’t reach the set water level?

The washer will not work when the filled water does not reach the set water level.

---

What is the selection of rinse water level?

The selection of rinse water level: the level is equal to wash water level. When the rinse program starts, the indicator light which stands for rinse level flickered. The user can select the rinse water level according to needs. Rinse level exceeds that wash level all the time. It shows the wash level if not press this button. And only show rinse level when rinse.

---

What happens after pressing down the [ON/OFF] button?

After pressing down [ ON/OFF], if the [Start / Pause ] button is not pressed, the power will be automatically cut off after 10 minutes.

---

What will influence the actual capacity?

The thickness, size, and type of clothes will influence the actual capacity. Be careful to only load a reasonable amount of laundry.

---

What type of detergent is recommended?

It is suggested not to use high sudsing detergent. Choose a low suds or high efficiency detergent.

---

How do I reduce the risk of fire, electric shock, or injury?

To reduce the risk of fire, electric shock, or injury to persons, read and follow this entire Owner’s Manual, including the Important Safety Instructions, before operating this washer.

---

How do I clean the washer?

Unplug the washer before cleaning to avoid the risk of electric shock. Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the finish.

---

How do I clean the lint bag and filter?

The special circulation water flow is designed for this washer, thus the flock powder and flock residues will be automatically collected into the filtering bag. After application, the user shall regularly clean the filtering bag to remove the flock powder and flock residues. Detail operation methods are following:

1. Unscrew the water inlet hose.
2. Take out the filter.
3. Clear the filter.
4. Install the filter and screw on the water inlet pipe.
5. Press the top of the lint filter, then pull out off the lint filter plate.
6. Press the buckle which is upper of the filter, then remove the filter.
7. Clean of filtering bag.
8. After cleaning of the filtering bag, install the filter and the filtering plate.

---

How do I clean the pump filter?

Only for the upper drain system, detail operation methods are following. Clean up every two months.

1. Place a rag or towel under the wash filter to avoid wetting the floor, and rotate the filter counterclockwise and pull it out.
2. Remove any dirt from the filter.
3. Return the filter to its place by rotating the filter clockwise until it locks into position.

---

What should I do if the spinning is intermittent when it starts?

Redistribute the load evenly and close the top lid.

---

What should I do if the wash procedure pauses?

The cloth sensor is detecting, it will add water after about 55 seconds.

---

What should I do if I select a spin program, but it does not work?

The program is setting the drain time, a period of time is needed before the spin program starts.

---

What should I do if there is some water in the drain hose when I first use the machine?

It is the water remaining after the performance inspection by the factory.

---

What are the troubleshooting tips?

• If the machine does not work normally, or alarms, please check as the following list. If the problem persists, please contact local service office or the sales service department of our company. The customer should not dismantle the machine without professional skills.

---

What are the possible causes of the washer not turning on?

Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.

---

Why might the machine have a small amount of water when I use it for the first time?

Normally, the water was the factory inspection remained.

---

What are the possible causes of the machine not washing?

• The power is off or the fuse is burned out.
• The power supply voltage is too low.
• The water reaches to the required water level. (The machine will not work before reaching the required water level).

---

What should I do if I cannot operate the buttons?

Did you use the “Child Lock” function? If you want to choose other functions after power on, please press "start/pause "button firstly.

---

What are the possible causes of no water flowing in, or water flowing slowly?

• The tap is not turned on, or the water supply is cut off.
• The screen of the inlet valve is blocked by dirt.
• The tap or the water-filling pipe has been frozen.
• You have chosen the “Delay” function.
• The “start/pause” button has not been pressed.

---

What are the possible causes of the wash cycle time being longer than usual?

The spin effect will change due to different types of clothing.

---

What should I do if the machine suddenly stops working?

Is the power or water supply cut off suddenly? If you press the "start/pause” button?

---

What happens if the machine sets drainage time?

When the washing machine is setting drainage time, it is starting spin after going through a period of time.

---

What are the possible causes of the machine making noise?

• The machine is tilted or shaking.
• Coins, zippers, and other objects have dropped in.
• The noise is normal when the motor is working.

---

What are the possible causes of the machine not draining or draining too slowly?

• The drain is bent, blocking, or freezing.
• The highest point of the drain is above ground 10cm.

---

What should I do if the control panel becomes hot?

Electronic Components thermal effect is a normal phenomenon.

---

What should I do if the washing effects are not good?

Select a proper procedure. Add the proper detergent quantity according to the instructions in the detergent package.

---

Why is the wash cycle time longer than usual?

This is normal. The washer adjusts cycle time automatically to provide optimal results for the selected cycle. The time remaining shown in the display is only an estimate. Actual time may vary.

---

What are the possible causes of “EI” error code?

No water flows in. If the tap is turned on, or the water supply is cut off? If it still has such a problem, please contact the local service office.

---

What are the possible causes of “E2” error code?

The machine does not drain. Is the water drain hose placed too high? Is the end of the water drain hose blocked?

---

What are the possible causes of “E3” error code?

The lid is not closed. Close the lid.

---

What are the possible causes of “E4” error code?

The water level sensor has failed. Please contact the local service office.

---

What are the possible causes of “EB” error code?

The machine is not balanced. If clothing piled up at one side of the barrel or if the machine is placed unsteadily.

---

What are the possible causes of “CL” error code?

The child-lock alarm. Remove the child-lock function.

---

What program is recommended for normally soiled load?

Normal+Water level 8 is the recommended program for normally soiled load equal to the rated capacity.