Post questions, comments, reviews or page errors in the comment box below.
Your File is Ready … Download PDF
PDF Content Summary: OWNER’S MANUAL LG Wi-Fi Sound Bar Please read this manual carefully before operating your set and retain it for future reference. MODEL SN8Y (SN8Y, SPN8-W) lg.com
2009_Rev02 Copyright © 2020 LG Electronics Inc. All Rights Reserved.
2 Getting Started Safety Information CAUTION 1 RISK OF ELECTRIC SHOCK DO NOT OPEN G e CAUTION: TO REDUCE THE RISK OF ELECTRIC t t i n SHOCK DO NOT REMOVE COVER (OR BACK) g S NO USER-SERVICEABLE PARTS INSIDE REFER t a SERVICING TO QUALIFIED SERVICE PERSONNEL. r t e d This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not use high voltage products around this product. (ex. Electrical swatter) This product may malfunction due to electrical shock. CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus. NOTICE: For safety marking information including product identification and supply ratings, please refer to the main label on the bottom or the other surface of the product. CAUTION concerning the Power Cord The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible. Check the specification page of this owner’s manual to be certain of the current requirements. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your device, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the device, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device. CAUTION: Be careful to make sure children do not put their hands or any objects into the *speaker duct. * speaker duct: A hole for plentiful bass sound on speaker cabinet. (enclosure) CAUTION: Only use the AC adapter supplied with this device. Do not use a power supply from another device or another manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty.
Getting Started3 Symbols ~ Refers to alternating current (AC). 1 0 Refers to direct current (DC). Refers to class II equipment. G e t t i 1 Refers to stand-by. n g S t ! Refers to “ON” (power). a r t e d Refers to dangerous voltage.
6 Getting Started Introduction Symbol used in this manual 1 , Note Indicates special notes and operating features. G e t t >Caution i n g S Indicates cautions for preventing possible damages t a r from abuse. t e d Getting Started 7 Front panel 1 G e t t i n g S t a r t e d 1 (Standby) - Switches the unit ON or OFF. F (Function) - Select the function and input source by pressing F repeatedly. Input source / Function Display Wi-Fi WI-FI Bluetooth BT Optical
A ARC e-ARC LG Sound Sync (Wired) OPT/HDMI ARC
HDMI IN HDMI USB USB o/p (Volume) - Adjusts volume level. / (Wi-Fi) - Selects Wi-Fi function. B Remote sensor Display Window - Display window will be darkened automatically if there is no key input for 15 seconds. C When you press any button, the display window will brighten. 8 Getting Started Precautions in using the touch buttons ⮹ Use the touch buttons with clean and dry hands. - In a humid environment, wipe out any moisture on the touch buttons before using.
1 . G e t t i n g S t a r t e d ⮹ Do not press the touch buttons hard to make it work. - If you apply too much strength, it can damage the sensor of the touch buttons. ⮹ Touch the button that you want to work in order to operate the function correctly. ⮹ Be careful not to have any conductive material such as metallic object on the touch buttons. It can cause malfunctions.
, This unit will turn itself off to save electric consumption when the main unit is not connected to an external device and is not used for 15 minutes. Getting Started 9 Rear panel 1 G e t t i n g S t a r t e d A DC IN - Connect to the AC adapter. HDMI IN - Connect HDMI IN jack on the back of the unit to HDMI OUT jack on the external device. B You can enjoy the sound and picture from HDMI connection on an external device. C HDMI OUT (TV eARC/ARC) - Connect the HDMI OUT (TV eARC/ARC) jack on the back of the unit to ARC jack on the TV. D OPTICAL IN - Connect the OPTICAL IN jack on the back of the unit to OPTICAL OUT jack on the TV. E USB Port - Connect USB memory device to the USB port on the back of the unit. 10 Getting Started Remote control 1 Replacement of Battery Remove the battery cover on the rear of the remote G e control, and insert the battery with 4 and 5 t t i matched correctly. n g S Risk of fire or explosion if the battery is replaced by t a r an incorrect type. t e d 1 (Standby) - Switches the unit ON or OFF. a ⮹ Networked standby: It allows the unit to switch to standby mode. To turn on Networked standby function, Press 1. To turn off Networked standby function, press 1 for about 3 seconds. b VOL (Volume) o/p - Adjusts speaker volume. c C/V (Skip) - Press Cor V to go to next or previous file. d N (Play/Pause) - Starts playback. / Pauses playback. Getting Started 11 SOUND EFFECT - Selects a sound effect mode by using SOUND EFFECT. On Display Description 1 AI SOUND PRO Analyzes the property of the input sound and provides the G sound optimized for the content in real time. e t t i BASS BLAST or BASS BLAST+ Reinforces the bass and powerful sound. n g S STANDARD You can enjoy premium sound with MERIDIAN technology. t a r t MOVIE You can enjoy more immersive and cinematic surround sound. e d MUSIC You can enjoy more good sound for music source. e , When this unit detects DOLBY ATMOS or DTS:X stream, you cannot change sound effect to any other. In this case, even though you press SOUND EFFECT, this unit does not respond. And you can see only “NOT SUPPORTED” on the display window. ⮹ TV remote: It allows you to control the volume of this unit by your TV remote control even by other company’s product. (Page 41) To turn on or off the TV Remote function, press and hold SOUND EFFECT for about 3 seconds and press it again. , Supported TV brands LG Panasonic Philips Samsung Sharp Sony Toshiba Vizio (Sound tuning) - Adjusts sound level of each speaker. Select the speaker you want to adjust by using and adjust the sound level by using VOL o/p. , Adjusting rear speakers level is applied only when the rear speakers are connected. , See the page 13 for more information of speakers. Display Description Range WF Sub Woofer -15 ~ 6 f C Center -6 ~ 6 OVC Overhead Volume Control -6 ~ 6 R Rear -6 ~ 6 TRE Treble -5 ~ 5 BAS Bass -5 ~ 5 ⮹ Surround sound: It allows you to enjoy surround sound with rear speakers. (Page 22) To turn on or off the surround sound, press and hold for about 3 seconds and press it again. g F (Function) - Select the function and input source by pressing F repeatedly. h [ (Mute) - Press [ to mute your unit. To cancel it, press [ again. 12 Getting Started J (Information) - You can display various information of the input source by pressing J. - Wi-Fi: Connected Application name 1 - BT (Bluetooth): Connected Bluetooth device name
G e t t i n g S t a r t e d i - OPT (Optical)/ARC/E-ARC/HDMI (HDMI IN): Audio format - USB: File information contained on a USB. ⮹ Auto Power ON/OFF: It allows the unit to turn on and off automatically by input signal: Optical (Page 41) To turn on or off AUTO POWER function, press and hold J for about 3 seconds and press it again.
j REPEAT - Press REPEAT to select desired repeat or random mode. k FOLDER W/S - Searches a folder on USB device. Getting Started 13 Speakers position 1 G e t t i n g S t a r t e d c c b a b d e e a Center speaker b Front speakers c Top speakers d Subwoofer e Rear speakers , You can enjoy surround sound by using Wireless Rear Speaker kit. Wireless Rear Speakers Kit sold separately (SPK8-S).
14 Getting Started Installing the sound bar You can hear the sound by connecting the unit to the 1 other device: TV, Blu-ray disc player, DVD player, etc. Place the unit in front of the TV and connect it to the G device you want. (Pages 26 - 32) e t t i You can place the wireless subwoofer anywhere in n g your room. But it is better to place the subwoofer S t a near the main unit. Turn it slightly toward the center r t e of the room to reduce the wall reflections. d For the best surround sound, place the speakers as shown below. , Note ⮹ If the sound bar covers the remote sensor of the TV, please separate distance between the sound bar and TV by 10 ~ 15 cm or more. ⮹ The illustration above may differ from actual units. ⮹ You can enjoy surround sound by using Wireless Rear Speaker kit. Wireless Rear Speakers Kit sold separately (SPK8-S). >Caution ⮹ For best performance of wireless connection such as Bluetooth or wireless subwoofer, do not install the unit on Metallic furniture because wireless connection communicates through a module positioned on the bottom of the unit. ⮹ Be careful not to make scratches on the surface of the Unit /Subwoofer when installing or moving them. Mounting the unit on a wall >Caution Getting Started 15 Preparation materials Unit 1 G
⮹ Do not install this unit upside down. It can damage the parts of this unit or be the cause of personal injury. ⮹ Do not hang onto the installed unit and avoid any impact to the unit. ⮹ Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may result in an injury or damage to the product. ⮹ When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall. (Not supplied) , Note Wall bracket install guide Wall bracket Screws Screws (A) Wall plug e t t i n g S t a r t e d
You can mount the main unit on a wall. >Caution Because it is difficult to make a connection after installing this unit, you should connect the cables before installation. Screws (A) and Wall Plugs are not supplied for mounting the unit. We recommend the Hilti (HUD-1 6 x 30) for the mounting. 16 Getting Started 1. Match the TV’s BOTTOM EDGE of Wall bracket install guide with the bottom of TV and attach to the position. 1 G e t t i n g S t a r t e d 2. When you mount it on a wall (concrete), use the wall plugs. You should drill some holes. A guide sheet (Wall bracket install guide) is supplied to drill. Use the sheet to check the point to drill. 3. Remove the Wall bracket install guide. 4. Fix the brackets with screws (A) as shown in the illustration below. 5. Put the unit on the brackets to match screw holes on the bottom of the unit. 6. Fix the unit with the screws firmly. , Note To detach the unit, perform it in reverse order. Network connection You can enjoy various functions of this sound bar by connecting to network and your smart device with “Google Home” app. Modem Media Server Router The “Google Home” app is required to connect the sound bar wirelessly to the network. , Note In a network environment (Router, Internet and Internet Service Provider) that supports both IPv4 and IPv6, the network automatically connects to IPv4 or IPv6 when connecting to the network. You can check the each network status by selecting the settings of My Speakers ([Settings]>[IP Info.]) on the “LG Wi-Fi Speaker” app. Connecting 17 Installing “Google Home” App The “Google Home” app allows you to use various functions of this speaker through your smart device. Requirements before setup ⮹ A wireless router must be connected to the internet. A smart device such as Android or iOS devices must be connected to the wireless router via Wi-Fi connection. 2 ⮹ It needs Google account to use this app. During connect Wi-Fi, this app may request to create C o Google account. n n e c t Through “Google Play” or “App Store” i n g 1. Tap the“Google Play Store” icon or “App Store” icon on your smart device. 2. Type in “Google Home” in the search bar and tap “Search” on “Google Play” or “App Store” 3. Select “Google Home” in the search result list to download. Google Home , Note ⮹ Depending on the device version, “Google Home” app may not work. ⮹ For more information, visit the web site. google.com/cast/setup/ 18 Connecting Launch the app to connect Wi-Fi Make sure your smart device Wi-Fi feature is turned on. Once a connecting operation is performed, it does not need to be performed again. , Note In case of iOS devices, it should be turned on Bluetooth setting on your smart device. 2 1. Tap the “Google Home” icon to launch the app. C o n n e c t i n g 2. Follow the screen on app to set speaker. Follow these instructions in order. , Note ⮹ Use the same Wi-Fi connection to set the speaker and your smart device. ⮹ If the Bluetooth setting turned on your smart device, it will be easy to connect Wi-Fi. ⮹ During installation, you should create a speaker name. It is needed when pairing the Bluetooth device. You can check and edit the speaker name. Follow the “Edit speaker name”. (Page 40) 3. When the speaker is properly connected to Wi-Fi, “CONNECTED” will appear on the display window with sound. , Note ⮹ Depending on wireless router status, it might not work well Wi-Fi connection. ⮹ It is recommended that you use Wi-Fi Group Play with less than 5 speakers. ⮹ “Google Home” app is provided by Google. It might be revised by a change of Google Policy. Organizing cables (Optional) You can organize the cable with cable ties. 1. Hold the cables together with cable ties as shown below. 2. Tighten cable ties. , Note ⮹ After all connections are completed, you can arrange cables as needed. ⮹ Cable ties are not provided. Connecting 19 Connecting the AC Adapter Connect the sound bar to the power supply with the supplied AC adapter. 1. Connect the supplied AC power cord to the AC adapter. 2 2. Connect the AC adapter cable to DC IN adapter input. C 3. Plug the AC power cord into an AC outlet. o n n e c t i n g >Caution Only use the AC adapter supplied with this device. Do not use a power supply from another device or manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty. 20 Connecting Wireless subwoofer and rear speaker (Sold Separately) connection Wireless subwoofer connection 2 LED indicator of wireless subwoofer C LED Color Status o n n e c Manually pairing wireless subwoofer When your connection is not completed, you can check red LED on the wireless subwoofer and the wireless subwoofer does not make sound. To solve the problem, follow the steps below. 1. Press Pairing on the rear of the wireless subwoofer. Pairing
t i n g Green (Blink) The connection is trying.
Green The connection is completed. Red The wireless subwoofer is in standby mode or the connection is failed. - The green LED on the rear of the wireless subwoofer blinks quickly. (If the green LED does not blink, press and hold the Pairing.) 2. Turn on the sound bar.
Off (No display) The power cord of wireless subwoofer is disconnected. - Pairing is completed. The green LED on the rear of the wireless subwoofer turns on.
Setting up the wireless subwoofer for the first time 1. Connect the power cord of the sound bar and the wireless subwoofer to the outlet. 2. Turn on the sound bar. The sound bar and the wireless subwoofer will be automatically connected. - Pairing is completed. The green LED on the rear of the wireless subwoofer turns on. Connecting 21 , Note Rear speakers connection (Sold
⮹ It takes a few seconds (and may take longer) for the main unit and the subwoofer to communicate with each other and make sounds. ⮹ The closer the main unit and the subwoofer, the better sound quality. It is recommended to install the main unit and the subwoofer as close as possible and avoid the cases below. - There is an obstacle between the main unit and the subwoofer. - There is a device using same frequency with this wireless connection such as a medical equipment, a microwave or a wireless LAN device. - Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference. ! 1 m Separately) Connecting the rear speakers 1. Connect the black stripe wire to the terminal marked - (minus) and the other end to the terminal marked + (plus). 2 C o n n e c t i n g 2. Connect the wireless receiver and the rear speakers (left, right) with the speaker cables. Color Position Blue Rear left Grey Rear right , Note You need to purchase the wireless rear speakers kit (SPK8-S) to enjoy surround sound. 22 Connecting >Caution ⮹ Use the speaker supplied with this unit only. Using any other speaker may cause malfunction. ⮹ Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack bass. 2 LED indicator of wireless receiver C o n n LED Color Status e c t i n Manually pairing wireless receiver When your connection is not completed, you can see the red LED on the wireless receiver and rear speakers do not make sound. To solve the problem, follow the below steps. 1. Press PAIRING on the rear of the wireless receiver.
g Yellow - green (Blink) The connection is trying.
Yellow - green The connection is completed. Red The wireless receiver is in standby mode or the connection is failed. - The yellow - green LED on the wireless receiver blinks quickly. 2. Turn on the main unit - Paring is completed. The yellow - green LED on
Off (No display) The power cord of wireless receiver is disconnected. the wireless receiver turns on.
Setting up the wireless receiver for the first time 1. Connect the power cord to the wireless receiver to the outlet. 2. Turn on the main unit: The sound bar and wireless receiver will be automatically connected. - Yellow - green LED on the wireless receiver turns on. Surround sound You can enjoy magnificent surround sound for all the input sound source with rear speakers. If you turn on the surround function, the whole speaker outputs sound. When you turn off the surround function, the speakers output sound as an original input sound channel. To turn on surround function, press and hold on the remote control for about 3 seconds and press it once again while “OFF - SURROUND” is scrolled. To turn off surround function, press and hold on the remote control for about 3 seconds and press it once again while “ON - SURROUND” is scrolled.
Connecting 23 Surround function ON Sound Effect Input Output
No rear speakers Rear speakers connected AI SOUND PRO 2.0 Ch 5.1 Ch 2 BASS BLAST or BASS BLAST+ STANDARD MOVIE MUSIC 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more C o n n e c t i n g
24 Connecting Surround function OFF Sound Effect Input Output No rear speakers Rear speakers connected 2.0 Ch
2 C o n n e c t i n g AI SOUND PRO BASS BLAST or BASS BLAST+ STANDARD MOVIE MUSIC 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more 2.0 Ch 5.1 Ch 7.1 Ch or more
How to Affix the Ferrite Core Connecting 25 , Note Ferrite core may not be provided depending on each nation’s regulations. Affix the Ferrite Core for speaker cables You must affix a ferrite core in order to reduce or eliminate electrical interference. 1. Pull the stopper [a] of the ferrite core to open. 2. Wind the speaker cables around the ferrite core twice. 3. Close the ferrite core until it clicks. ⮹ If there is a strong electromagnetic wave product nearby, interference may occur. Put the main unit and wireless receiver away from there. ⮹ The wireless receiver will automatically switch to standby mode in a few minutes after the sound bar is turned off. When the wireless receiver is in standby 2 mode, the LED will turn on in red. C ⮹ When you turn on the sound bar, the wireless o n receiver will turn on and the LED will change n e to yellow - green and then the rear speakers c t i n makes sound within a few seconds. g ⮹ It takes a few seconds (and may take longer) for the main unit and Wireless Receiver to communicate with each other. ⮹ Use the rear speaker at least 30 cm away from either TV screen or PC monitor. ⮹ When the wireless receiver is being connected or disconnected with the main unit, output sound is maybe interrupted. ⮹ Set the distance between the sound bar and the wireless receiver as close as possible and keep them away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference. ! 1 m 26 Connecting Connecting to your TV Please connect with this unit and TV using the optical digital cable or HDMI cable considering the state of the TV. Using an OPTICAL cable 1. Connect the OPTICAL IN jack on the back of the 2 unit to OPTICAL OUT jack on the TV using an OPTICAL cable. C o n n e c t i n g Optical cable 2. Select the input source to OPT/HDMI ARC by pressing F repeatedly. You can see “OPT” on the display window if connecting normally between this unit and your TV. , Note ⮹ Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover. ⮹ You can enjoy the TV audio through the speakers of this unit. In the case of some TV models, you must select the external speaker option from the TV menu. (For details, reference your TV user manual.) ⮹ If this unit is connected by OPTICAL and ARC at the same time, the ARC signal has a higher priority. LG Sound Sync You can control some functions of this unit by your TV’s remote control with LG Sound Sync. It is compatible with the LG TV that supports LG Sound Sync. Make sure of the LG Sound Sync logo is on your TV. Controllable function by LG TV’s remote control: Volume up/down, mute , Note ⮹ You can also use the remote control of this unit while using LG Sound Sync. If you use TV’s remote control again, the unit synchronizes with the TV. According to TV Specifications, the volume and mute of this unit synchronize with TV. ⮹ When the connection fails, make sure of the condition of the TV and power. ⮹ Make sure of the condition of this unit and the connection in the cases below when using LG Sound Sync. - The unit is turned off. - Changing to another function. - Disconnecting the optical cable. ⮹ The amount of time to turn off this unit is different depending on your TV when you set AUTO POWER function to ON. LG Sound Sync with wired connection Connecting 27 Using an HDMI cable 1. Connect your LG TV to the unit by using an optical cable. Optical cable 2. Set up the sound output of TV to listen to the sound through this unit: (Refer to the TV’s instruction manual for the details of LG Sound Sync.) 3. Turn on the unit by pressing 1. 4. Select the input source to OPT/HDMI ARC by pressing F repeatedly. You can see “LGOPT” on the display window if connecting normally between this unit and your TV. If you connect this unit to a TV that supports HDMI CEC and ARC (Audio Return Channel), you can enjoy the TV audio through the speakers of this unit without connecting the optical cable. 1. Connect the HDMI OUT (TV eARC/ARC) jack on the back of the unit to ARC jack on the TV using an HDMI cable. 2 C o n n e c HDMI cable t i n g 2. Select the input source to OPT/HDMI ARC by pressing F repeatedly. You can see “ARC” or “E-ARC” on the display window if connecting normally between this unit and your TV. , Note ⮹ You can enjoy the TV audio through the speakers of this unit. In the case of some TV models, you must select the external speaker option from the TV menu. (For details, reference your TV user manual.) ⮹ Depending on your LG TV model, you may need to turn on the SIMPLINK function on your LG TV. ⮹ When you return to ARC function from another function, you need to select the input source to OPT/HDMI ARC. Then this unit changes to ARC function automatically. 28 Connecting ARC (Audio Return Channel) function The ARC function enables an HDMI capable TV to send the audio stream to HDMI OUT of the unit. eARC (Enhanced Audio Return Channel) function 2 eARC (Enhanced Audio Return Channel) features an advancement over the existing ARC (Audio Return Channel) and supports the latest high-bitrate audio C o n formats such as DTS-HD Master Audio™, DTS:X®, n e Dolby® TrueHD, Dolby Atmos® and more. c t i n You can use your multiple components just by simple g connection. Preparing to Use the eARC or ARC Function - Your TV must support the HDMI-CEC and eARC or ARC function and the HDMI-CEC and eARC or ARC must be set to On. - The setting method of HDMI-CEC, eARC or ARC may differ depending on the TV. For details about eARC or ARC function, refer to your TV manual. - You must use the certified HDMI cable. (page 29) - You must connect the HDMI OUT on the unit with HDMI IN of the TV that supports eARC or ARC function using an HDMI cable. - You can connect only one Sound bar to TV compatible with eARC or ARC. What is SIMPLINK? Some functions of this unit are controlled by the TV’s remote control when this unit and LG TV’s with SIMPLINK are connected through HDMI connection. Controllable functions by LG TV’s remote control: Power on/off, volume up/down, etc. Refer to the TV owner’s manual for the details of SIMPLINK function. LG TV’s with SIMPLINK function has the logo as shown above. , Note ⮹ Depending on the state of the unit, some SIMPLINK operation may differ from your purpose or not work. ⮹ Depending on a TV or a player which is connected with this unit, SIMPLINK operation may differ from your purpose. Additional information for HDMI Connecting 29 HDMI cable Checklist ⮹ When you connect an HDMI or DVI compatible device make sure of the following: - Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player. - The connected device’s video input is set correctly for this unit. - The connected device is compatible with 720 x 576p (or 480p), 1280 x 720p, 1920 x 1080i, 1920 x 1080p, 4096 x 2160p or 3840 x 2160p video input. ⮹ Not all HDCP-compatible HDMI or DVI devices will work with this player. - The picture will not be displayed properly with non-HDCP device. , Note ⮹ If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output. ⮹ Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again. ⮹ When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable. ⮹ If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m). ⮹ You cannot change the video resolution in the HDMI mode. Change the video resolution of the connected component. ⮹ If the video output signal is abnormal when your personal computer is connected to HDMI IN jack, change the resolution of your personal computer to 576p (or 480p), 720p, 1080i or 1080p. Some HDMI cables have poor signal transmission, which can cause problems with sound and video transmission. Even after HDMI cable connections, if no sound, sound interrupted, noise occurring from the sound bar and/or no video, no smooth video on your TV, the HDMI cable may be the problem. Use the cable marked with the premium HDMI 2 certification logo. We recommend using “High Speed HDMI Cable with Ethernet” or later version. C o STANDARD HDMI CABLE WITH ETHERNET (X) n n e c t HIGH SPEED HDMI CABLE (X) i n g HIGH SPEED HDMI CABLE WITH ETHERNET (O) Premium High Speed HDMI® Cable with Ethernet (O) ULTRA HIGH SPEED HDMI® CABLE (O) Connection through HDMI Cable* Your television must support the newest HDMI features (HDMI CEC1) / ARC (Audio Return Channel)) to fully enjoy the Live broadcasting channel with audio system through an HDMI cable. Unless your TV supports these HDMI features, the audio system should be connected through an OPTICAL cable. 1) HDMI CEC (High-Definition Multimedia Interface Consumer Electronics Control) Consumer Electronics Control (CEC) is an HDMI feature designed to allow the user to command and control the CEC-enabled devices, that are connected through HDMI by using only one of their remote controls. * Trade names for CEC are SimpLink (LG) , Anynet+ (Samsung), BRAVIA Sync (Sony), EasyLink (Philips), etc. 30 Connecting Optional equipment connection DOLBY ATMOS® What is DOLBY ATMOS®? 2 Dolby Atmos gives you amazing experience you’ve never before by overhead sound, and all the richness, C clarity, and power of Dolby sound. o n n e DTS:X® c t i n g What is DTS:X®? In the real world, sound is all around us, moving freely in any direction. DTS:X® is immersed in this natural, multi-dimensional sound experience as we go about our daily lives. For using DOLBY ATMOS® and DTS:X® ⮹ To enjoy content containing Dolby Atmos® and DTS:X®, the connected device and content must support Dolby Atmos® and DTS:X®. ⮹ DOLBY ATMOS® is available only in HDMI and ARC mode. ⮹ DTS:X® is available only in HDMI and ARC mode. ⮹ It is needed to set up an audio output on external devices (Blu-ray disc player, TV etc.) to “No encoding” such as “Bitstream”, “Auto” or “Bypass”. - If you can select audio output sampling rate, set it to 192 kHz. ⮹ If your TV does not support DTS sound source, connect the playback (source) device to the HDMI IN or OPTICAL IN jack on the soundbar to listen to DTS audio. 1. Connect HDMI IN jack on the back of the unit to HDMI OUT jack on the external device such as Blu-ray disc player, DVD player, etc. 2. Connect HDMI OUT (TV eARC/ARC) jack on the back of the unit to HDMI IN (ARC) jack on the TV. 3. Select the input source to HDMI or OPT/HDMI ARC by pressing F repeatedly. - If you select HDMI, you can hear the sound from the external device. Select it when playing the external device. - If you select OPT/HDMI ARC, you can hear the sound from your TV. Select it when watching the TV. You can see “DOLBY ATMOS” or “DTS:X” on the display window if connecting normally between this sound bar and your TV and the contents is played. , Note ⮹ DOLBY ATMOS®/DTS:X® supports 3.1.2 channel. (5.1.2 channel when it connected with Rear kit) ⮹ If the sound bar does not have sound or the video on TV is not smooth, the HDMI cable may be the problem. Refer to the HDMI cable checklist. (Page 29) HDMI IN connection You can enjoy the sound from the external device which is connected to HDMI IN jack on this unit. To the Blu-ray disc player, DVD player, etc. 1. Connect HDMI IN jack on the back of the unit to HDMI OUT jack on the audio device such as Blu ray disc player, DVD player, etc. 2. Select the input source to HDMI by pressing F repeatedly. Connecting 31 OPTICAL IN connection Connect an optical output jack of external devices to the OPTICAL IN jack. Optical cable 2 C To the optical output o n jack of external device n e c t i n g 1. Connect the OPTICAL IN jack on the back of the unit to optical out jack of your external device. 2. Select the input source to OPT/HDMI ARC by pressing F repeatedly. You can see “OPT” on the display window if connecting normally between this unit and your device. , Note Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover. >Caution Make sure to properly align and connect the optical cable; improper alignment may cause damage to the jack. Optical jack Optical cable Optical jack Optical cable <O> <X> 32 Connecting Optional equipment connection You can enjoy both sound and picture from the external device you connect. 2 C o n n e c t i n g OR 1. Connect HDMI IN jack of your TV to HDMI OUT jack on the external device such as Blu-ray disc player, DVD player, etc. 2. Connect the OPTICAL IN jack on the back of the unit to OPTICAL OUT jack on the TV using an OPTICAL cable. Or connect the HDMI OUT (TV eARC/ARC) jack on the back of the unit to HDMI IN (ARC) jack on the TV using an HDMI cable. 3. Select the input source to OPT/HDMI ARC by pressing F repeatedly. , Note If the sound bar does not have sound or the video on TV is not smooth, the HDMI cable may be the problem. Refer to the HDMI cable checklist. (Page 29) USB connection Connect USB memory device to the USB port on the back of the unit. For more information of playing files on a USB, refer to the page 35. Removing the USB Device from the unit 1. Choose a different function/mode. 2. Remove the USB device from the unit. Compatible USB devices ⮹ MP3 Player: Flash type MP3 player. ⮹ USB Flash Drive: Devices that support USB 2.0. ⮹ The USB function of this unit does not support some USB devices. USB device requirement ⮹ Devices which require additional program installation connected to a computer, are not supported. ⮹ Do not extract the USB device while in operation. Connecting 33 Playable file Sampling Frequency MP3: within 32 to 48 kHz OGG: within 32 to 48 kHz AAC: within 32 to 48 kHz ⮹ For a large capacity USB, it may take longer than a few minutes to be searched. ⮹ To prevent data loss, back up all data. ⮹ The unit’s USB Port cannot be connected to PC. The unit can not be used as a storage device. ⮹ The exFAT file systems are not supported on this unit. (FAT16/FAT32/NTFS systems are available.) ⮹ Depending on some devices, it may not available to recognize the followings on this unit. - External HDD - Card readers - Locked devices - Hard type USB devices - USB hub - Using USB extension cable - iPhone/iPod/iPad - Android device FLAC: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz (16 bit/ 24 bit) WAV: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz (16 bit/ 24 bit) 2 Bitrate resolution C o n MP3: within 8 to 320 kbps n e OGG: within 64 to 320 kbps c t i n AAC: within 8 to 320 kbps g ⮹ Maximum files: Up to 2,000 ⮹ Maximum directories: Up to 200 ⮹ A protected file by DRM (Digital rights management) cannot be played on the unit. ⮹ Video files in the USB storage device can not be played. ⮹ Depending on the performance of your USB device, playback may not work well.
34 Connecting , Note ⮹ Folders and files on the USB are recognized as below. : Folder
2 C o n n e c t i n g *ROOT a c A B C D E b H I d : File F G J
⮹ If there is no file in a folder, the folder will not appear. ⮹ File will be played from file $A to file $J one by one. ⮹ Files will be played in order recorded and it may be different depending on the record circumstances. ⮹ This unit can display file or folder names that contain numbers or English characters only. ⮹ *ROOT: The first screen you can see when a this unit recognize the USB is “ROOT”.
USB operation Operating 35 , Note 1. Connect the USB device to the USB port. 2. Select the USB function by pressing F repeatedly. To Do this Playback Press N. Pause During playback, press N. During playback, press V on the remote control to go to the next file. Playing less than 3 seconds, ⮹ The resume point may be cleared when you pull out the power cord or removing the USB device from the unit. ⮹ Repeat/Random playback operates as follows. On Display Description OFF Plays songs on USB device in order. ONE Plays a same song repeatedly. FOLDER Plays songs in a folder repeatedly.
Skip to the next/ previous file Play repeatedly or randomly press C on the remote control to go to the previous file. Playing after 3 seconds, press C on the remote control to go to the beginning of the file. Press REPEAT on the remote control repeatedly. Refer to the note for details about the display change. ALL Plays all the songs on USB device repeatedly. SHUFFLE Plays all the songs once randomly, and stops the playback. 3 O p e r a t i n g
Search a folder Press FOLDER W/S on the remote control. 36 Operating Works with the Google Assistant This unit works with the Google Assistant. You can control some functions of this unit: Play and stop music and volume control. Requirements ⮹ Google Assistant built-in device (Sold Separately) ⮹ This unit must be connected to Internet. ⮹ This unit must be registered in [Google Home] app. 3 O p e r a t i n g
“LG Wi-Fi Speaker” The “LG Wi-Fi Speaker”app is provided by LG Electronics. This app allows you to use various functions of this speaker through your smart device: Requirements before using You should connect to Wi-Fi by using “Google Home” app prior using this app. (Page 18) Enjoying music on your device and home network server You can listen to the music on your smart device and home network server. Using Chromecast built-in You can enjoy music contents through this sound bar with Chromecast enabled apps. Setting and controlling the sound bar You can manage the sound bar settings and control the sound bar even without remote control. Requirements ⮹ A wireless router must be connected to the internet. ⮹ A smart device such as a smartphone or tablet must be connected to the wireless router via Wi Fi connection. , Note For more informations of “LG Wi-Fi Speaker”, follow the instructions of the application. Operating 37 Installing “LG Wi-Fi Speaker” App Through Apple “App Store” or “Google Play Store” 1. Tap the Apple “App Store” icon or “Google Play Store” icon. 2. Type in “LG Wi-Fi Speaker” in the search bar and tap “Search”. 3. Select “LG Wi-Fi Speaker” in the search result list to download. , Note 3 ⮹ “LG Wi-Fi Speaker” app will be available in version of the software as follow; O Android OS: Ver 5.0 (or later) p e iOS: Ver 10 (or later) r a t i ⮹ Depending on the device, “LG Wi-Fi Speaker” n g app may not work. ⮹ You can find the available application of this unit by using “LG Audio” app. Android OS: Ver 5.0 (or later) 38 Operating Using a BLUETOOTH Wireless Technology About BLUETOOTH Bluetooth is wireless communication technology for short range connection. The sound may be interrupted when the connection interfered by the other electronic wave or you connect the Bluetooth in the other rooms. Connecting individual devices under Bluetooth wireless technology does not incur any charges. A mobile phone with Bluetooth wireless technology 3 can be operated via the Cascade if the connection was made via Bluetooth wireless technology. O p e ⮹ Available Devices: Smart phone, MP3, Notebook, r a t etc. i n g ⮹ Version: 5.0 ⮹ Codec: SBC BLUETOOTH profiles In order to use Bluetooth wireless technology, devices must be able to interpret certain profiles. This speaker is compatible with following profile. A2DP (Advanced Audio Distribution Profile) Listening to Music of a BLUETOOTH Device Before you start the pairing procedure, make sure that the Bluetooth feature on your smart device is turned on. Refer to your Bluetooth device’s user guide. Once a pairing operation is performed, it does not need to be performed again. 1. Select the Bluetooth function by pressing F repeatedly. “BT” and then “READY” appears in the display window. 2. Operate the Bluetooth device and perform the pairing operation. When searching for this speaker on your Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device. If your unit is connected to Wi-Fi, you can see the name you set in the Google Home app. If the unit is not connected to Wi-Fi, “LG-SN8Y_XXXX” appears. 3. Select the speaker name of your unit. , Note ⮹ Speaker name was setup in the Google Home app. For example, if the speaker name is set to “Living Room” in the Google Home app, you will see “Living Room” on your Bluetooth device. ⮹ XXXX means the last four digits of address. For example, if your unit has a MAC address such as 20:C3:8F:C9:31:55, you will see “LG-SN8Y_3155” on your Bluetooth device. ⮹ You may check and edit the speaker name on “Google Home” app (Page 40) ⮹ Depending on the Bluetooth device type, some devices have a different pairing way. For details about Bluetooth pairing, refer to your Bluetooth device manual. 4. When this unit is successfully connected with Operating 39 , Note your Bluetooth device, “PAIRED” [ your device’s name [ “BT” appears on the display window. , Note ⮹ If it is unavailable to display device name on the unit, “-” will be displayed. ⮹ To check the connected device’s name, press J on the remote control. The connected Bluetooth device’s name is displayed. 5. Listen to music. To play music in your Bluetooth device, refer to your Bluetooth device’s user guide. According to your Bluetooth device’s volume level, the volume level of Bluetooth will be adjusted. , Note ⮹ When using Bluetooth technology, you have to make a connection between the unit and the Bluetooth device as close as possible and keep the distance. However it may not work well in the case below: - There is an obstacle between the unit and the Bluetooth device. - There is a device using same frequency with Bluetooth technology such as a medical equipment, a microwave or a wireless LAN device. ⮹ If last connected device is LG TV, this sound bar will connect to the TV automatically when you restart the sound bar. ⮹ If the LG TV is turned off, this sound bar will enter “READY” (Bluetooth ready) mode. When the TV is turned back on, the Sound Bar will not reconnect automatically. To connect the Sound Bar and the TV: - Turn the Sound Bar off and back on. Then follow the TV’s on screen instructions. ⮹ Available TV: LG TV models released after 2016 and some TVs may not work well. ⮹ This unit supports Bluetooth auto pairing. However it does not operate in the case below: - When you restart this unit. - When you disconnect this unit by yourself. - When you disconnect this unit on the connected Bluetooth device. ⮹ The sound may be interrupted when the connection is interfered with by the some other electronic wave. ⮹ Pairing is limited to “One” Bluetooth device. Multi-Pairing is not supported. ⮹ Depending on the type of the device, you may 3 not be able to use the Bluetooth function. ⮹ You can enjoy using Bluetooth when using O p Phone, MP3, Notebook, etc.. e r a t ⮹ The more distance between the unit and the i n g Bluetooth device, the lower the sound quality becomes. ⮹ Bluetooth connection will be disconnected when the unit is turned off or the Bluetooth device gets to far from the unit. ⮹ If the Bluetooth connection is disconnected, connect the Bluetooth device again. ⮹ When a Bluetooth device is not connected, “READY” appears on the display window. ⮹ If you change to another function after connecting Bluetooth device, Bluetooth connection will be disconnected. When you return to Bluetooth function, Bluetooth connection will be connected automatically. ⮹ When one Bluetooth device has connected to this unit, another device cannot find and connect to this unit. If you want to connect another device, disconnect the current device and try again.
40 Operating Controls connected BLUETOOTH device You can control the connected Bluetooth device from the unit; play, pause, skip, volume. , Note ⮹ Only Android OS and iOS is available to use this function.. ⮹ This function may not be supported depending on the Bluetooth device or some of TV operated differently. Edit speaker name 3 You can check and edit the speaker name on the “Google Home” app. O p e r a t i n g
Other operations Operating 41 AUTO POWER On/Off Using your TV remote control You can control some functions of this unit by your TV remote control even by other company’s product. Controllable functions are volume up/down and mute. Press and hold SOUND EFFECT on the remote control for about 3 seconds. “ON - TV REMOTE” appears and you can control this unit by your TV remote control. To check the status of this function, press and hold SOUND EFFECT on the remote control. To turn off this function, press and hold SOUND EFFECT on the remote control and press it once again while “ON - TV REMOTE” is scrolled. , Note ⮹ Make sure that the sound output of your TV is set to [External speaker]. ⮹ This function does not operate on LG TV’s magic remote control. ⮹ This function may not work well when some TV control functions such as HDMI CEC, SIMPLINK and LG Sound Sync set to ON. ⮹ This function may not work well when the unit and the TV are connected with an HDMI cable. ⮹ Some remote control may not be supported. This sound bar automatically turns on and off by an input source: Optical To turn on this function, press and hold J on the remote control for about 3 seconds and press it once again while “OFF - AUTO POWER” is scrolled. To check the status of this function, press and hold J on the remote control. To turn off this function, press and hold J on the remote control for about 3 seconds and press it once again while “ON - AUTO POWER” is scrolled. Turning on When you turn on your TV or an external device 3 connected to this unit, this unit recognizes the input signal and selects the suitable function. You can hear O p the sound from your device. e r a t i n Turning off g When the TV is off, this sound bar switches to the Networked standby mode. , Note ⮹ After the unit is turned on by AUTO POWER function, it will be automatically turned off if there is no signal for a certain period of time from the TV connected by LG Sound Sync (Optical). ⮹ After the unit is turned on by AUTO POWER function, it will be automatically turned off if there is no signal for a certain period of time from the external device. ⮹ If you turned off the unit directly, it cannot be turned on automatically by AUTO POWER function. However the unit can be turned on by AUTO POWER function when optical signal comes in after 5 seconds of no signal. ⮹ Depending on the connected device, this function may not operate. ⮹ When you turn on this unit for the first time, status of Auto Power function is turned on. ⮹ You can set the AUTO POWER function only when this unit is turned on.
42 Operating Auto function change This sound bar recognizes input signals such as Optical, HDMI ARC, Bluetooth, and “LG Wi-Fi Speaker” app and then changes suitable function automatically. When you turn on your TV or an external device When you turn on your TV or an external device connected by the one among Optical, LG Sound Sync (Optical), or HDMI ARC, this sound bar will change to a suitable function so you can listen to the sound through it. 3 When you try to connect a BLUETOOTH device O p When you try to connect your Bluetooth device to e r a this unit, Bluetooth function is selected. Play your t i n g music on the Bluetooth device. When you play music by “LG Wi-Fi Speaker” app When you play music by “LG Wi-Fi Speaker” app on your smart device, this sound bar changes the function to WI-FI and you can listen to the music through it. , Note This unit does not change the function to optical if SIMPLINK of the connected TV, Bluray disc player, set-top box or etc. device set to on or connected CEC supported device is turned on. If you want to use the auto function change, turn off SIMPLINK function on your LG TV. It takes for about 30 seconds to turn off SIMPLINK.
Standby mode The speaker switches to the standby mode if there is no music playback or no button operation. Standby mode If you press and hold 1 for about 3 seconds, the speaker switches to the standby mode. Then “GOOD BYE” appears on the display window. And all wireless network ports are deactivated. Networked standby mode Option 1. When music is not played and buttons are not pressed for 15 minutes, the speaker switches to the Networked standby mode. Then “GOOD-BYE” appears on the display window. Option 2. If you press 1, the speaker switches to the Networked standby mode. Then “GOOD-BYE” appears on the display window. Operating 43 Reset the Speaker If the speaker doesn’t respond, reset the speaker. Press and hold the / on the unit until you hear the beep sound once. You can see “RESET” on the display window. Then all the stored wireless network information is deleted. 3 O p e r a t i n g
44 Troubleshooting Troubleshooting General Symptoms Cause & Solution
The unit does not work properly. The power does not turn on. ⮹ Turn off the power of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and turn them on again. ⮹ Disconnect the power cord of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting again. ⮹ Previous setting may not be saved when device power is shut off. Is the power cord plugged into the outlet? ⮹ Connect the power plug to the outlet.
Sound is not produced. Is the volume set to minimum? ⮹ Adjust the volume. ⮹ When you are using connection with a external device (set top box, Bluetooth 4 device etc.), adjust volume level of the device. Is the mute function activated? T r o ⮹ Press [ or adjust the volume level to cancel the mute function. u b l e Is the function selected properly? s h o ⮹ Check the input source and select the correct input source. o t i n g No woofer sound Is the subwoofer plugged in? ⮹ Plug the power cord of subwoofer into the wall outlet securely. Is pairing between the unit and the subwoofer disconnected? ⮹ Connect the unit and the subwoofer. (Page 20)
The remote control does not work properly. The AUTO POWER function does not work. LG Sound Sync does not work. Is the remote control too far from the unit? ⮹ Operate the remote control within about 7 m. Is there an obstacle in the path of the remote control and the unit? ⮹ Remove the obstacle. Are the batteries in the remote control exhausted? ⮹ Replace the batteries with new one. ⮹ Check connection of the external device such as TV, DVD/Blu-Ray player. ⮹ Check the state of SIMPLINK on your LG TV and turn off SIMPLINK. ⮹ Depending on the connected device, this function may not operate. ⮹ Check whether your LG TV supports LG Sound Sync (Wired). ⮹ Check connection of LG Sound Sync (Wired). ⮹ Check sound setting of your TV and this unit.
Troubleshooting 45 Symptoms Cause & Solution
When you feel the output sound of the unit is low. Check the details below and adjust the unit according to them. ⮹ Switch the state of DRC function to [OFF] by using “LG Wi-Fi Speaker”. ⮹ With the sound bar connected with TV, change the AUDIO DIGITAL OUT setting on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM]. ⮹ With the sound bar connected with Player, change the AUDIO DIGITAL OUT setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or [BITSTREAM]. ⮹ Change Audio DRC setting on connected device setup menu to [OFF] state. ⮹ Make sure that Night Time mode is not On. Turn off Night Time mode.
USB is not recognized ⮹ Format the USB device and connect it again. When formatting the USB device, select the available file system. (Page 33)
Bluetooth pairing does not work well. ⮹ Be sure your Bluetooth device is on. ⮹ Switch Bluetooth off and on again on your Bluetooth device, then try pairing again. ⮹ Remove the obstacle in the path of the Bluetooth device and the unit. ⮹ Depending on the type of the Bluetooth device or surrounding environment, 4 your device may not be paired with the unit. T r o u b l e s h o o t i n g
46 Troubleshooting Network Symptoms Cause & Solution
4 Cannot connect the speaker to your home network. Wi-Fi connection does not work well. Application ⮹ The wireless communication may be interrupted from household devices that are using radio frequencies. Move the speaker away from them. ⮹ Check your router. Try turning it off and back on. ⮹ Check that the Wi-Fi feature is turned on in your smart device. ⮹ Check that the speaker and your smart device are connected to same Wi-Fi. If you restart the router? ⮹ You need to turn the speaker’s power off and on again. If you install new router. ⮹ You need to perform a factory set and setup the network connection for speaker.
Symptoms Cause & Solution T r o u b
le s ho o t i n g The application doesn’t work properly. Does an error occur when accessing the app? ⮹ Make sure that your smart device is compatible with the app. ⮹ Make sure that the application is the latest version. ⮹ Make sure that the connected unit turns on.
Troubleshooting 47 NOTES to use wireless Symptoms Cause & Solution
This device may have wireless interference. Bluetooth device may malfunction or make noise in the following cases. ⮹ Wireless may not operate normally in weak signal area. ⮹ Please install the device close enough to wireless subwoofer. ⮹ Do not install the device on metal furniture for optimum performance. ⮹ When any part of your body contact the transceiver of the Bluetooth device or sound bar. ⮹ When there is an obstacle or wall or the device is installed in a secluded spot. ⮹ When there is a device (a wireless LAN, a medical equipment or a microwave) using same frequency, make the distance between the products as far away as possible each other. ⮹ When connecting the device to the Bluetooth device, make the distance between the products as close as possible each other. ⮹ When the device gets too far from the Bluetooth device, the connection is disconnected and also malfunction may occur. 4 T
NOTES to release Demo mode r o u b l e s h Symptoms Cause & Solution o o t i n
Can not change input source with F such as BT (Bluetooth), HDMI etc. and only [DEMO] indication is showing in the front display. g Unplug the power cord and plug it in again. If that doesn’t work, after setting the volume to 2, press and hold F (About 5 seconds) on the main unit until the
display indicates current selected function. Remote Control does not work. (No response)
48 Appendix File requirement Available File extensions: “.mp3”, “.aac”, “.ogg”, “.flac”, “.wav” Sampling Frequency MP3: within 32 to 48 kHz OGG: within 32 to 48 kHz AAC: within 32 to 48 kHz FLAC: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz (16 bit/ 24 bit) WAV: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz (16 bit/ 24 bit) Bitrate resolution MP3: within 8 to 320 kbps OGG: within 64 to 320 kbps AAC: within 8 to 320 kbps ⮹ The file requirements are not always compatible. There may have some restrictions by file features and media server’s ability. ⮹ Depending on the types of file or ways of recording, it may not play back. ⮹ Some DRM-loaded files are not supported on this 5 speaker. ⮹ The types of supported files may differ depending A p on the operating system and/or the manufacturer p e n of the smart device and PC. d i x Trademarks and licenses All other trademarks are trademarks of their respective owners. Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, and the double-D symbol are Trademarks of dolby Laboratories. For DTS patents, see patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Appendix 49 Specifications General Power consumption Refer to the main label on the unit. Model: DA-50F25
AC adapter Manufacturer: Asian Power Devices Inc. Input: 100 - 240 V ~ 50 - 60 Hz Output: 25 V 0 2 A
Dimensions (W x H x D) Approx. 1060.0 mm x 57.0 mm x 119.0 mm (with foot) Operating temperature 5 °C to 35 °C Operating humidity 5 % to 90 % Bus Power Supply (USB) 5 V 0 500 mA Available Digital Input Audio Sampling Frequency 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 192 kHz Available Digital Input Audio format Dolby Atmos, Dolby Audio, DTS:X, DTS-HD, PCM Input/Output OPTICAL IN 3 V (p-p), Optical jack x 1 HDMI IN 19 Pin (Type A, HDMI™ connector) x 1 5 HDMI OUT 19 Pin (Type A, HDMI™ connector) x 1 4K Sources dependent on HDCP 2.3 are supported at 4K resolutions. A p p e n d i x Amplifier (RMS Output) Total 440 W RMS Front 40 W RMS x 2 (4 Ω at 1 kHz, THD 10 %) Center 40 W RMS (4 Ω at 1 kHz, THD 10 %) Top 50 W RMS x 2 (4 Ω at 1 kHz, THD 10 %) Subwoofer 220 W RMS (3 Ω at 80 Hz, THD 10 %) 50 Appendix Wireless subwoofer Power requirements Refer to the main label on the subwoofer. Power consumption Refer to the main label on the subwoofer. Type 1 Way 1 Speaker Impedance 3 Ω Rated Input Power 220 W RMS Max. Input Power 440 W RMS Dimensions (W x H x D) Approx. 221.0 mm x 390.0 mm x 312.8 mm System Wireless LAN (Internal antenna) 802.11a/b/g/n Wi-Fi networks SPK8-S (SPK8-S, S78S1-S), Sold Separately Wireless receiver Power requirements Refer to the main label on the wireless receiver. Power consumption Refer to the main label on the wireless receiver. Rear 70 W RMS x 2 (3 Ω at 1 kHz, THD 10 %) Dimensions (W x H x D) Approx. 60.0 mm x 220.0 mm x 175.0 mm 5 A p p Rear speakers (Each) e n d Type 1 Way 1 Speaker i x Impedance 3 Ω Rated Input Power 70 W RMS Max. Input Power 140 W RMS Dimensions (W x H x D) Approx. 100.0 mm x 140.0 mm x 100.0 mm ⮹ Designs and specifications are subject to change without prior notice.
54 Appendix OPEN SOURCE SOFTWARE NOTICE INFORMATION To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to firstname.lastname@example.org. This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information. 5 A p p e n d i x
FREE ENGLISH PDF
USER GUIDE - USER MANUAL
OWNER GUIDE - OWNER MANUAL
REFERENCE GUIDE - REFERENCE MANUAL
INSTRUCTION GUIDE - INSTRUCTION MANUAL