LG DLG3601 (01) PDF Document

The Control Lock feature is turned on. To turn off Control Lock, turn the LG DLG3601 on, then press and hold the button that has *Control Lock on or under it for 3 seconds.

Proper airflow is critical to the efficient operation of clothes dryers. A lint filter which is full of lint or clogged with fabric softener sheet residue can reduce the airflow to the point that the time required to dry clothing will be greatly increased. Another factor affecting dry time is your home exhaust system. An exhaust system which is dirty and clogged with lint, or is excessively long, needs to be professionally cleaned or repaired.

This is how the Wrinkle Care feature works. The LG DLG3601 runs briefly every few minutes for up to 3 hours after the cycle finishes. This feature is designed to help prevent wrinkles from setting in when the dryer is not unloaded immediately after the cycle is finished.

Step 1. Clean the Lint Filter. If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load. This will help ensure the fastest and most efficient drying performance. Make sure to reinstall the filter, pressing down until it clicks firmly into place.

Step 2. Load the Dryer. Load the LG DLG3601 with the wet laundry from the washer. If the load is extra large, you may need to divide it into smaller loads for proper performance and fabric care.

Step 3. Turn on the Dryer. Press the Power button to turn on the dryer. The cycle LEDs will illuminate and a chime will sound.

Step 4. Select a Cycle. Turn the cycle selector knob in either direction until the LED for the desired cycle is on. The preset temperature, dry level, and option settings for that cycle will be shown. Default settings for the selected cycle can now be changed if desired.

Step 5. Begin Cycle. Press the Start/Pause button to begin the cycle. The cycle can be paused at any time either by opening the door or by pressing the Start/Pause button. If the cycle is not restarted within 14 minutes of being paused, the dryer will shut off and the settings will be lost.

Step 6. End of Cycle. When the cycle is finished, the chime will sound. Immediately remove your clothing from the dryer to reduce wrinkling. If Wrinkle Care is selected, the dryer will tumble briefly every few minutes to help prevent wrinkles from setting in the clothes.

Always make sure the lint filter is clean before starting a new load; a clogged lint filter will increase drying time. To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Push the lint filter firmly back into place. Always ensure the lint filter is properly installed before running the dryer. Running the dryer with a loose or missing lint filter will damage the dryer and articles in the dryer.

Combine large and small items in the same load.

Damp clothes will expand as they dry. Do not overload the dryer; clothes require room to tumble and dry properly.

Use mesh laundry bags to separate clothes with zippers, hooks, straps, and drawstrings to prevent them from catching on or tangling with other clothes or damaging the lint filter.

The following table shows the meaning of the tumble dry symbols:

The following table shows the heat setting indications:

The following table summarizes the settings for Sensor Dry Cycles on the LG DLG3601 (Note: ‘*’ indicates Energy Saver is on by default):

The following table summarizes the settings for Manual Dry Cycles on the LG DLG3601:

Step 1. Remove the drying rack and literature, and then close the door. Do not load anything in the drum for this test, as it may affect the accuracy of the results.

Step 2. Press and hold Energy Saver and Temp.

Step 3. Then press the Power button.

Step 4. Press the START/PAUSE button.

The dryer will start the test, which will last a few minutes. The heat will be turned on and the temperatures in the drum will be measured.

Check the display for results.

If the Flow Sense indicator LED has not turned on when the cycle ends, the exhaust system is adequate.

If the exhaust system is severely restricted, the Flow Sense LED will turn on.

If no bars are displayed on the Flow Sense display when the cycle ends, the exhaust system is adequate.

If the exhaust system is severely restricted, the display will show four bars.

At the end of the test cycle, End will display. The test cycle will end and the dryer will shut off automatically after a short delay.

Possible Cause: Temperature sensor failure.

Solution: Turn off the LG DLG3601 and call for service.

Possible Cause: Humidity sensor failure.

Solution: Turn off the LG DLG3601 and call for service.

Possible Cause: Electric dryer power cord is not connected correctly, or house power supply is incorrect.

Solution: Check the power supply or the connection of the power cord to the terminal block. Refer to the Connecting Electric Dryers section of this manual for complete instructions.

Possible Cause: House fuse is blown, circuit breaker has tripped, or power outage has occurred.

Solution: Reset circuit breaker or replace fuse. Do not increase the fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.

Possible Cause: Gas supply or service turned off.

Solution: Confirm that house gas shutoff and the dryer gas shutoff are both fully open.

Possible Cause: After clearing the restriction, the Flow Sense system requires multiple, consecutive cycles to determine that the performance value has improved before the Flow Sense indicator is reset.

Solution: If the Flow Sense indicator remains active for more than five cycles after the restriction has been cleared, call for service.

Possible Cause: Exhaust system is too long or has too many turns/restrictions. Partial blockage of the ductwork due to lint buildup or other foreign object. The appliance has detected a restriction in the external dryer venting.

Solution: Install a shorter or straighter duct run. See the Installation Instructions for details. Ductwork should be checked/cleaned immediately. Dryer can be used in this condition, but drying times will be longer and energy consumption will increase. If exhaust restrictions are sensed by the Flow Sense system, the indicator will remain on for 2 hours after the end of the cycle. Opening the door or pressing the Power button will turn off the display.

Possible Cause: Lint filter not cleaned properly.

Solution: Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. If it looks dirty, follow the cleaning instructions. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.

Possible Cause: More Time button was pressed.

Solution: Press the LESS TIME button to reduce the indicated load size.

Possible Cause: House fuse is blown, circuit breaker has tripped, or power outage has occurred (for electric models).

Solution: Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. NOTE: Due to the design of electric dryers, it is possible for a circuit problem to allow an electric dryer to run without heat.

Possible Cause: Gas supply or service is turned off (for gas models).

Solution: Confirm that the house gas shutoff and the dryer gas shutoff valves are both fully open. Even if gas is not supplied to the dryer, it will run and no error codes will display. Verify that other gas appliances in the home are working normally.

Possible Cause: Large load of heavy fabrics.

Solution: Heavy fabrics take longer to dry because they tend to retain more moisture. To help reduce and maintain more consistent drying times for large and heavy fabrics, separate these items into smaller loads of a consistent size.

Possible Cause: Dryer controls are not set properly.

Solution: Use the appropriate control settings for the type of load you are drying. Some loads may require an adjustment of the dry level setting for proper drying.

Possible Cause: Lint filter needs to be cleaned.

Solution: Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. With some loads that produce high amounts of lint, such as new bath towels, it may be necessary to pause the cycle and clean the filter during the cycle.

Possible Cause: House fuse is blown, circuit breaker has tripped, or power outage has occurred.

Solution: Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. NOTE: Due to the design of electric dryers, it is possible for a circuit problem to allow an electric dryer to run without heat.

Possible Cause: Dryer is overloaded.

Solution: Divide extra large loads into smaller loads for better drying performance and efficiency.

Possible Cause: Dryer is underloaded.

Solution: If you are drying a very small load, add a few extra items to ensure proper tumbling action. If the load is very small and you are using SENSOR DRY cycles, the electronic control cannot properly sense the dryness of the load and may shut off too soon. Use TIME DRY or add some extra wet clothes to the load.

Possible Cause: ENERGY SAVER option selected (on some models).

Solution: If using the Normal cycle, deselect the ENERGY SAVER option. This option reduces energy use by adding an air dry section to the beginning of the cycle. It is normal to feel no heat at the beginning of the cycle while in ENERGY SAVER mode.

Possible Cause: Heat settings, load size, or dampness of clothing is not consistent.

Solution: The drying time for a load will vary depending on the type of heat used (electric, natural gas, or LP gas), the size of the load, the type of fabrics, the wetness of the clothes, and the condition of the exhaust duct and lint filter. Even an unbalanced load in the washer can cause poor spinning, resulting in wetter clothes which will take longer to dry.

Possible Cause: Fabric softener used incorrectly.

Solution: Confirm and follow the instructions provided with your fabric softener.

Possible Cause: Clean and dirty clothes are being dried together.

Solution: Use your dryer to dry only clean items. Soil from dirty clothes can transfer to the clean clothes in the same or later loads.

Possible Cause: Clothes were not properly cleaned or rinsed before being placed in the dryer.

Solution: Stains on dried clothes could be stains that were not removed during the washing process. Make sure that clothes are being completely cleaned or rinsed according to the instructions for your washer and detergent. Some difficult soils may require pre-treating prior to washing.

Possible Cause: Clothes dried too long (over dried).

Solution: Over drying a load of laundry can lead to wrinkled clothes. Try a shorter drying time or LESS DRY setting and remove items while they still retain a slight amount of moisture.

Possible Cause: Clothes left in dryer too long after cycle ends.

Solution: Use the WRINKLE CARE option. This feature will tumble the clothes briefly every few minutes for up to 3 hours to help prevent wrinkling.

Possible Cause: Garment care instructions are not being followed.

Solution: To avoid shrinking your clothes, always consult and follow fabric care instructions. Some fabrics will naturally shrink when washed. Other fabrics can be washed but will shrink when dried in a dryer. Use a low or no heat setting.

Possible Cause: Lint filter not cleaned properly.

Solution: Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. If it looks dirty, follow the cleaning instructions. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.

Possible Cause: Laundry not sorted properly.

Solution: Some fabrics are lint producers (i.e., a fuzzy white cotton towel) and should be dried separately from clothes that are lint trappers (i.e., a pair of black linen pants).

Possible Cause: Excess static in clothes.

Solution: Use a fabric softener to reduce static electricity. Be sure to follow the manufacturer’s instructions. Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use SENSOR DRY cycles.

Possible Cause: Dryer is overloaded.

Solution: Divide extra large loads into smaller loads for drying.

Possible Cause: Tissue, paper, etc., left in pockets.

Solution: Check pockets thoroughly before washing and drying clothes.

Possible Cause: Fabric softener is not used or used incorrectly.

Solution: Use a fabric softener or the REDUCE STATIC option, if equipped, to reduce static electricity. Be sure to follow the manufacturer’s instructions.

Possible Cause: Clothes dried too long (overdried).

Solution: Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use MANUAL DRY cycles. Select a LESS DRY setting on SENSOR DRY cycles, if necessary.

Possible Cause: Drying synthetics, permanent press, or synthetic blends.

Solution: These fabrics are naturally more prone to static buildup. Try using fabric softener, or use LESS DRY and/or shorter TIME DRY time settings.

Possible Cause: Very large load or very small load. Single large item such as a blanket or comforter.

Solution: If items are too tightly packed or too sparse the sensor may have trouble reading the dryness level of the load. Use a TIME DRY cycle for very small loads. Large, bulky items such as blankets or comforters can sometimes wrap themselves into a tight ball of fabric. The outside layers will dry and register on the sensors, while the inner core remains damp. When drying a single bulky item, it may help to pause the cycle once or twice and rearrange the item to unwrap and expose any damp areas.

To dry a few remaining damp items from a very large load or a few damp spots on a large item after a sensor cycle has completed, empty the lint trap, then set a TIME DRY cycle to finish drying the item(s).

Possible Cause: The password for the Wi-Fi network was entered incorrectly.

Solution: Delete your home Wi-Fi network and begin the registration process again.

Possible Cause: Mobile data for your smartphone is turned on.

Solution: Turn off the Mobile data on your smartphone before registering the appliance.

Possible Cause: The wireless network name (SSID) is set incorrectly.

Solution: The wireless network name (SSID) should be a combination of English letters and numbers. Do not use special characters.

Possible Cause: The router frequency is not 2.4 GHz.

Solution: Only a 2.4 GHz router frequency is supported. Set the wireless router to 2.4 GHz and connect the appliance to the wireless router. To check the router frequency, check with your Internet service provider or the router manufacturer.

Possible Cause: The appliance is too far from the router.

Solution: If the appliance is too far from the router, the signal may be weak and the connection may not be configured correctly. Move the router closer to the appliance or purchase and install a Wi-Fi repeater.

Instructions for door reversal can be found in the owner’s manual.

To clean the lint filter, open the dryer door and pull the lint filter straight up. Then:

For everyday cleaning, roll any lint off the filter with your fingers, or

Vacuum the lint filter.

If the lint filter has become very dirty or clogged with fabric softener, wash the lint filter in warm, soapy water and allow it to dry thoroughly before reinstalling.

To reduce the risk of fire, electric shock, or injury to persons, read the SAFETY INSTRUCTIONS before operating this appliance.

Press the button to turn the dryer ON. Press again to turn the dryer OFF.

Pressing the Power button during a cycle will cancel that cycle and any load settings will be lost.

Turn this knob to select the desired cycle. Once the desired cycle has been selected, the standard presets will be shown in the display. On Manual Dry cycles, these settings can be adjusted using the cycle modifier buttons anytime before starting the cycle.

Press this button to start the selected cycle. If the dryer is running, use this button to pause the cycle without losing the current settings.

If you do not press the Start/Pause button to resume a cycle within 14 minutes, the dryer turns off automatically and all cycle settings are lost.

Use these buttons to select the desired cycle settings for the selected cycle. The current settings are shown in the display. Press the button for that option to view and select other settings.

Use these buttons with the Time Dry and other Manual Dry cycles to adjust the drying time. Press the More Time button to increase the selected manual cycle time by 5 minutes; press the Less Time button to decrease the cycle time by 5 minutes.

The appliance plays a melody when the drying cycle is finished. The buttons make a sound each time a button is pressed. Use this button to turn the melody and button tones on or off.

To turn on/off, press the Signal button.

When this function is turned on, the On/Off LED on the display lights up.

Selecting this option will tumble the load periodically for up to 3 hours after the selected cycle, or until the door is opened. This is helpful in preventing wrinkles when you are unable to remove items from the dryer immediately.

To turn on/off, press and hold the Wrinkle Care button for 3 seconds.

When this option is selected, the dryer signals when the load is approximately 80% dry. This allows you to remove faster-drying lightweight items or items that you would like to iron or hang while they are still slightly damp.

To turn on/off, press the Damp Dry Signal button.

To turn on/off, press and hold the Dry Level button for 3 seconds.

This option helps to reduce the energy consumption of the Normal Cycle, depending on the load size. When the Energy Saver option is selected, the cycle begins with an air dry section and the drying time is increased.

The Energy Saver option is turned on by default in the Normal Cycle. Turn off the Energy Saver option for a faster Normal cycle which begins with heated drying. To turn the Energy Saver default off, press and hold the Energy Saver button. ON or OFF appears in the display.

Step 1. Turn on the dryer and turn the cycle selector knob to select the desired cycle.

Step 2. Use the cycle modifier buttons to adjust the settings for that cycle.

Step 3. Press the cycle option button(s) to add the desired options. A confirmation message is shown in the display.

Step 4. Press the Start/Pause button to start the cycle. The dryer starts automatically.

Use this button to select the level of dryness for the cycle. Press the Dry Level button repeatedly to scroll through available settings.

This option is only available with Sensor Dry cycles.

The dryer will automatically adjust the cycle time. Selecting dry levels above Normal will increase the cycle time. Selecting dry levels below Normal will decrease the cycle time.

Use the dry level between Normal and Damp or the Damp dry level for items that you wish to iron.

Use this button to adjust the temperature setting. This allows precise care of fabrics and garments. Press the Temp. button repeatedly to scroll through available settings.

Use this button to manually select the drying time, from 20 to 60 minutes, in 10-minute increments. Use this for small loads or to remove wrinkles. Use the More Time/Less Time buttons to add or reduce the drying time in 5-minute increments.

Press and hold the below button(s) for 3 seconds:

Press and hold the Dry Level button for 3 seconds.

When the controls are locked, ‘CL’ and the remaining time are alternately shown on the display during the dry cycle. All controls will be disabled except the Power button.

Press and hold the below button(s) for 3 seconds:

Press and hold the Dry Level button for 3 seconds.

Once set, Control Lock remains active until it is manually deactivated. Control Lock must be turned off to run another cycle.

The drum is equipped with a blue LED that illuminates when the dryer is turned on. This light automatically turns off when the door is closed and the cycle starts. To turn on the light during a cycle, press and hold the Wrinkle Care button for three seconds. The drum light will illuminate and then turn off automatically after four minutes.

To reduce the risk of serious injury, death, explosion, or fire, follow basic safety precautions, including the following:

Do not open the dryer door during steam cycles.

Do not touch the steam nozzle in the drum during or after the steam cycle.

Step 1. Turn on the dryer and turn the cycle selector knob to select the Steam Fresh cycle.

Step 2. To add an option, select Wrinkle Care.

Step 3. The display shows the load size (number of items). Change the steam time by pressing the More Time or Less Time buttons to fit the size of the load.

Step 4. Press Start/Pause to start the cycle.

Step 1. Turn on the dryer and turn the cycle selector knob to select the desired cycle.

Step 2. Use the cycle setting buttons to adjust the settings for that cycle.

Step 3. Press Turbo Steam to add steam. If desired, select the Reduce Static or Wrinkle Care options. Then adjust for the load size using the More Time or Less Time buttons.

Step 4. Press Start/Pause to start the cycle.

The Reduce Static option injects steam late in the drying cycle to reduce the static electricity caused by dry fabrics rubbing together.

When Sensor Dry is selected with the Reduce Static option, the dry levels below Normal cannot be selected.

The Reduce Static option can also be selected during Time Dry cycles.

After the Steam option is selected in Time Dry, the More Time or Less Time buttons will change the steam time ONLY.

Press the More Time or Less Time button to adjust the cycle time depending on the size of the load (7, 9, 11, 14, 16, or 18 items).

If the dryer does not heat (electric models):

Possible Cause: Power cord is not properly plugged in. House fuse is blown, circuit breaker has tripped, or power outage has occurred.

Solution: Make sure that the plug is securely plugged into a grounded outlet matching the dryer’s rating plate. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. NOTE: Due to the design of electric dryers, it is possible for a circuit problem to allow an electric dryer to run without heat.

Possible Cause: Exhaust ducts are blocked, dirty, or duct run is too long.

Solution: Confirm that the exhaust duct is properly configured and free of debris, lint, and obstructions. Make sure that outside wall dampers can open properly and are not blocked, jammed, or damaged.

Possible Cause: Load is not properly sorted.

Solution: Separate heavy items from lightweight items. Larger and heavier items take longer to dry. Light items in a load with heavy items can fool the sensor because the light items dry faster.

Possible Cause: This display indicates that the steam option has been set for a “big” item such as a comforter.

Solution: Press the LESS TIME button to reduce the indicated load size.

Possible Cause: The duct work is about 80% – 95% blocked. (“d80”, “d90” or “d95” error code is displayed for 2 hours only). House exhaust system blocked.

Solution: Do not use the dryer until the exhaust system has been cleaned and/or repaired. Using the dryer with a severely restricted exhaust is dangerous and could result in a fire or other property damage. Check the outside dryer vent while the dryer is operating to make sure there is strong airflow. If the exhaust system is extremely long, have it repaired or rerouted. Keep the area around the dryer clean and free of clutter. Check vent hood for damage or lint clogging. Make sure the area around the vent hood is clear.

Possible Cause: This is steam condensation.

Solution: The dripping water will stop after a short time.

Possible Cause: Too many or overly different types of garments in dryer.

Solution: Small loads of 1 to 5 items work best. Load fewer garments. Load similar types of garments.

Possible Cause: The function of this cycle is to remove wrinkles from fabric.

Solution: Use an iron to replace creases and pleats in garments.

Possible Cause: This is normal.

Solution: The amount of static experienced will depend on the individual moisture level in the skin.

Possible Cause: Correct drying options not selected.

Solution: Select the load weight manually before starting the Reduce Static option.

Possible Cause: Water level error.

Solution: Unplug dryer and call for service.

Possible Cause: This is normal.

Solution: Condensation will normally form on the inside of the dryer door during steam operation. Some condensation may drip out the bottom of the door.

Possible Cause: This is normal.

Solution: Steam vapor is difficult to see when the door is closed. However, condensation will normally form on the inside of the dryer door if the steam system is operating normally.

Possible Cause: This is normal.

Solution: The drum is turned off so that the steam vapor remains in the drum. The drum will normally turn for about 2 seconds once a minute.

Possible Cause: This is normal.

Solution: Steam is released at different stages of the cycle for each option.

Possible Cause: Steam Fresh did not remove odor completely.

Solution: Fabrics containing strong odors should be washed in a normal cycle.

Possible Cause: Power cord is not properly plugged in. House fuse is blown, circuit breaker has tripped, or power outage has occurred.

Solution: Make sure that the plug is securely plugged into a grounded outlet matching the dryer’s rating plate. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.