LG DLEX4000 (01) PDF Document

The Control Lock feature is turned on for your LG DLEX4000. To turn off Control Lock, turn the dryer on, then press and hold the button that has “Control Lock on or under it for 3 seconds.

Proper airflow is critical to the efficient operation of clothes dryers. A lint filter which is full of lint or clogged with fabric softener sheet residue can reduce the airflow to the point that the time required to dry clothing will be greatly increased. Another factor affecting dry time is your home exhaust system. An exhaust system which is dirty and clogged with lint, or is excessively long, needs to be professionally cleaned or repaired.

This is how the Wrinkle Care feature works on your LG DLEX4000. The dryer runs briefly every few minutes for up to 3 hours after the cycle finishes. This feature is designed to help prevent wrinkles from setting in when the dryer is not unloaded immediately after the cycle is finished.

When the Steam Fresh™ cycle is selected on your LG DLEX4000, the dryer displays the recommended number of garments for the cycle, not the estimated cycle time, until the cycle is started. Use the More Time or Less Time buttons to adjust the load size setting for the number of garments you desire. For a large load or single bulky item use the 6 / 9 (big) setting.

Possible Cause: After clearing the restriction, the Flow Sense™ system requires multiple, consecutive cycles to determine that the performance value has improved before the Flow Sense™ indicator is reset.

Solution: If the Flow Sense™ indicator remains active for more than five cycles after the restriction has been cleared, call for service.

Possible Cause: Power cord is connected incorrectly on the LG DLEX4000.

Solution: Check the connection of the power cord to the terminal block.

Possible Cause: Exhaust system is too long or has too many turns/restrictions, or partial blockage of the ductwork due to lint buildup or other foreign object.

Solution: Install a shorter or straighter duct run. See the Installation Instructions for details. Ductwork should be checked/cleaned immediately. Dryer can be used in this condition, but drying times will be longer and energy consumption will increase.

Possible Cause: The appliance has detected a restriction in the external dryer venting. After clearing the restriction, the Flow Sense™ system requires multiple, consecutive cycles to determine that the performance value has improved before the Flow Sense™ indicator is reset.

Solution: If the Flow Sense™ indicator remains active for more than five cycles after the restriction has been cleared, call for service.

Possible Cause: More Time button was pressed on the LG DLEX4000.

Solution: Press the LESS TIME button to reduce the indicated load size.

Possible Cause: The duct work is about 80% – 95% blocked. House exhaust system blocked on the LG DLEX4000.

Solution: Do not use the dryer until the exhaust system has been cleaned and/or repaired. Using the dryer with a severely restricted exhaust is dangerous and could result in a fire or other property damage. Check the outside dryer vent while the dryer is operating to make sure there is strong airflow. If the exhaust system is extremely long, have it repaired or rerouted. Keep the area around the dryer clean and free of clutter. Check vent hood for damage or lint clogging. Make sure the area around the vent hood is clear.

Possible Cause: Lint filter not cleaned properly on the LG DLEX4000.

Solution: Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. If it looks dirty, follow the cleaning instructions. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle.

The Control Lock feature is turned on for the LG DLEX4000. To turn off Control Lock, turn the dryer on, then press and hold the button that has “Control Lock on or under it for 3 seconds.

Possible Cause: Power cord is not properly plugged in. House fuse is blown, circuit breaker has tripped, or power outage has occurred.

Solution: Make sure that the plug is securely plugged into a grounded outlet matching the dryer’s rating plate. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician.

Possible Cause: House fuse is blown, circuit breaker has tripped, or power outage has occurred. Gas supply or service is turned off (Gas Model only).

Solution: Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. NOTE: Due to the design of electric dryers, it is possible for a circuit problem to allow an electric dryer to run without heat. Confirm that the house gas shutoff and the dryer gas shutoff valves are both fully open. Even if gas is not supplied to the dryer, it will run and no error codes will display. Verify that other gas appliances in the home are working normally.

Possible Cause: Large load of heavy fabrics. Dryer controls are not set properly. Lint filter needs to be cleaned. House fuse is blown, circuit breaker has tripped, or power outage has occurred. Dryer is overloaded. Dryer is underloaded. ENERGY SAVER option selected (on some models).

Solution: Heavy fabrics take longer to dry because they tend to retain more moisture. To help reduce and maintain more consistent drying times for large and heavy fabrics, separate these items into smaller loads of a consistent size. Use the appropriate control settings for the type of load you are drying. Some loads may require an adjustment of the dry level setting for proper drying. Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. With some loads that produce high amounts of lint, such as new bath towels, it may be necessary to pause the cycle and clean the filter during the cycle. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. NOTE: Due to the design of electric dryers, it is possible for a circuit problem to allow an electric dryer to run without heat. Divide extra large loads into smaller loads for better drying performance and efficiency. If you are drying a very small load, add a few extra items to ensure proper tumbling action. If the load is very small and you are using SENSOR DRY cycles, the electronic control cannot properly sense the dryness of the load and may shut off too soon. Use TIME DRY or add some extra wet clothes to the load. If using the Normal cycle, deselect the ENERGY SAVER option. This option reduces energy use by adding an air dry section to the beginning of the cycle.

Possible Cause: Heat settings, load size, or dampness of clothing is not consistent.

Solution: The drying time for a load will vary depending on the type of heat used (electric, natural gas, or LP gas), the size of the load, the type of fabrics, the wetness of the clothes, and the condition of the exhaust duct and lint filter. Even an unbalanced load in the washer can cause poor spinning, resulting in wetter clothes which will take longer to dry.

Possible Cause: Fabric softener used incorrectly. Clean and dirty clothes are being dried together. Clothes were not properly cleaned or rinsed before being placed in the dryer.

Solution: Confirm and follow the instructions provided with your fabric softener. Use your dryer to dry only clean items. Soil from dirty clothes can transfer to the clean clothes in the same or later loads. Stains on dried clothes could be stains that were not removed during the washing process. Make sure that clothes are being completely cleaned or rinsed according to the instructions for your washer and detergent. Some difficult soils may require pre-treating prior to washing.

Possible Cause: Clothes dried too long (over dried). Clothes left in dryer too long after cycle ends.

Solution: Over drying a load of laundry can lead to wrinkled clothes. Try a shorter drying time or LESS DRY setting and remove items while they still retain a slight amount of moisture. Use the WRINKLE CARE option. This feature will tumble the clothes briefly every few minutes for up to 3 hours to help prevent wrinkling.

Possible Cause: Garment care instructions are not being followed.

Solution: To avoid shrinking your clothes, always consult and follow fabric care instructions. Some fabrics will naturally shrink when washed. Other fabrics can be washed but will shrink when dried in a dryer. Use a low or no heat setting.

Possible Cause: Lint filter not cleaned properly. Laundry not sorted properly. Excess static in clothes. Dryer is overloaded. Tissue, paper, etc., left in pockets.

Solution: Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. If it looks dirty, follow the cleaning instructions. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle. Some fabrics are lint producers (i.e., a fuzzy white cotton towel) and should be dried separately from clothes that are lint trappers (i.e., a pair of black linen pants). Use a fabric softener to reduce static electricity. Be sure to follow the manufacturer’s instructions. Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use SENSOR DRY cycles. Divide extra large loads into smaller loads for drying. Check pockets thoroughly before washing and drying clothes.

Possible Cause: Fabric softener is not used or used incorrectly. Clothes dried too long (overdried). Drying synthetics, permanent press, or synthetic blends.

Solution: Use a fabric softener or the REDUCE STATIC option, if equipped, to reduce static electricity. Be sure to follow the manufacturer’s instructions. Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use MANUAL DRY cycles. Select a LESS DRY setting on SENSOR DRY cycles, if necessary. These fabrics are naturally more prone to static buildup. Try using fabric softener, or use LESS DRY and/or shorter TIME DRY time settings.

Possible Cause: Very large load or very small load. Single large item such as a blanket or comforter.

Solution: If items are too tightly packed or too sparse the sensor may have trouble reading the dryness level of the load. Use a TIME DRY cycle for very small loads. Large, bulky items such as blankets or comforters can sometimes wrap themselves into a tight ball of fabric. The outside layers will dry and register on the sensors, while the inner core remains damp. When drying a single bulky item, it may help to pause the cycle once or twice and rearrange the item to unwrap and expose any damp areas. To dry a few remaining damp items from a very large load or a few damp spots on a large item after a sensor cycle has completed, empty the lint trap, then set a TIME DRY cycle to finish drying the item(s).

Possible Cause: The password for the Wi-Fi network was entered incorrectly. Mobile data for your smartphone is turned on. The wireless network name (SSID) is set incorrectly. The router frequency is not 2.4 GHz. The appliance is too far from the router.

Solution: Delete your home Wi-Fi network and begin the registration process again. Turn off the Mobile data on your smartphone before registering the appliance. The wireless network name (SSID) should be a combination of English letters and numbers. (Do not use special characters.) Only a 2.4 GHz router frequency is supported. Set the wireless router to 2.4 GHz and connect the appliance to the wireless router. To check the router frequency, check with your Internet service provider or the router manufacturer. If the appliance is too far from the router, the signal may be weak and the connection may not be configured correctly. Move the router closer to the appliance or purchase and install a Wi-Fi repeater.

Possible Cause: This is steam condensation.

Solution: This is steam condensation. The dripping water will stop after a short time.

Possible Cause: Too many or overly different types of garments in dryer.

Solution: Small loads of 1 to 5 items work best. Load fewer garments. Load similar types of garments.

Possible Cause: The function of this cycle is to remove wrinkles from fabric.

Solution: Use an iron to replace creases and pleats in garments.

Possible Cause: This is normal.

Solution: The amount of static experienced will depend on the individual moisture level in the skin.

Possible Cause: Correct drying options not selected.

Solution: Select the load weight manually before starting the Reduce Static option.

Possible Cause: Water level error.

Solution: Unplug dryer and call for service.

Possible Cause: This is normal.

Solution: Condensation will normally form on the inside of the dryer door during steam operation. Some condensation may drip out the bottom of the door.

Possible Cause: This is normal.

Solution: Steam vapor is difficult to see when the door is closed. However, condensation will normally form on the inside of the dryer door if the steam system is operating normally.

Possible Cause: This is normal.

Solution: The drum is turned off so that the steam vapor remains in the drum. The drum will normally turn for about 2 seconds once a minute.

Possible Cause: This is normal.

Solution: Steam is released at different stages of the cycle for each option.

Possible Cause: Steam Fresh™ did not remove odor completely.

Solution: Fabrics containing strong odors should be washed in a normal cycle.

Step 1. Remove the drying rack and literature, and then close the door. Do not load anything in the drum for this test, as it may affect the accuracy of the results.

Step 2. Press and hold Signal and Temp. on the LG DLEX4000. Then press the Power button.

Step 3. Press the START/PAUSE button.

Step 4. The dryer will start the test, which will last a few minutes. The heat will be turned on and the temperatures in the drum will be measured.

Step 5. Check the display for results. During the test cycle, monitor the Flow Sense™ display on the control panel. If the Flow Sense™ LED has not turned on, when the cycle ends, the exhaust system is adequate. If the exhaust system is severely restricted, the Flow Sense™ LED will turn on. Other problems may also be shown with error codes.

Step 6. At the end of the test cycle, End will display. The test cycle will end and the dryer will shut off automatically after a short delay.

Press and hold the Damp Dry Signal button for 3 seconds on the LG DLEX4000.

When the controls are locked, CL and the remaining time are alternately shown on the display during the dry cycle. All controls will be disabled except the Power button.

Press and hold the Damp Dry Signal button for 3 seconds on the LG DLEX4000.

Once set, Control Lock remains active until it is manually deactivated. Control Lock must be turned off to run another cycle.

The drum is equipped with a blue LED that illuminates when the dryer is turned on. This light automatically turns off when the door is closed and the cycle starts. To turn on the light during a cycle on the LG DLEX4000, press and hold the Wrinkle Care button for three seconds. The drum light will illuminate and then turn off automatically after four minutes.

Step 1. Turn on the dryer and turn the cycle selector knob to select the Steam Fresh™ cycle on the LG DLEX4000.

Step 2. To add an option, select Wrinkle Care.

Step 3. The display shows the load size (number of items). Change the steam time by pressing the More Time or Less Time buttons to fit the size of the load.

Step 4. Press Start/Pause to start the cycle.

Step 1. Turn on the dryer and turn the cycle selector knob to select the Steam Sanitary™ cycle on the LG DLEX4000.

Step 2. Use the cycle setting buttons to adjust the settings for that cycle.

Step 3. Press Turbo Steam to add steam. If desired, select the Reduce Static or Wrinkle Care options. Then adjust for the load size using the More Time or Less Time buttons.

Step 4. Press Start/Pause to start the cycle.

Step 1. Turn on the dryer and turn the cycle selector knob to select the desired cycle on the LG DLEX4000.

Step 2. Use the cycle setting buttons to adjust the settings for that cycle.

Step 3. Press Turbo Steam to add steam. If desired, select the Reduce Static or Wrinkle Care options. Then adjust for the load size using the More Time or Less Time buttons.

Step 4. Press Start/Pause to start the cycle.

Step 1. For everyday cleaning, roll any lint off the filter with your fingers, or

Step 2. Vacuum the lint filter.

Step 3. If the lint filter has become very dirty or clogged with fabric softener, wash the lint filter in warm, soapy water and allow it to dry thoroughly before reinstalling.

Press the Wrinkle Care option button to select this option. Selecting this option will tumble the load periodically for up to 3 hours after the selected cycle, or until the door is opened. This is helpful in preventing wrinkles when you are unable to remove items from the dryer immediately.

To turn on/off, press the Damp Dry Signal button on the LG DLEX4000.

When this function is turned on, the On/Off LED on the display lights up.

To turn on/off, press the Signal button on the LG DLEX4000. This button controls the melody played when the cycle is finished and the sound made each time a button is pressed.

Fabric Type: Work clothes, corduroys, etc.

Dry Level (Default): Normal

Dry Level (Allowable Option): Adj.

Temp. (Default): Med. High (between Medium and High)

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Allowable Option (•)

Reduce Static: Default setting (=)

Fabric Type: Jeans, heavyweight items

Dry Level (Default): Normal

Dry Level (Allowable Option): Adj.

Temp. (Default): High

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Allowable Option (•)

Reduce Static: Allowable Option (•)

Fabric Type: Comforters, pillows, shirts

Dry Level (Default): Normal

Dry Level (Allowable Option): Adj.

Temp. (Default): Medium

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Not an option.

Reduce Static: Allowable Option (•)

Fabric Type: Do not use this cycle with delicate fabrics

Dry Level (Default): Very

Temp. (Default): High

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Not an option.

Reduce Static: Not an option.

Fabric Type: Permanent press, synthetic items

Dry Level (Default): Normal

Dry Level (Allowable Option): Adj.

Temp. (Default): Medium

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Allowable Option (•)

Reduce Static: Allowable Option (•)

Fabric Type: Lingerie, sheets, blouses

Dry Level (Default): Normal

Dry Level (Allowable Option): Adj.

Temp. (Default): Low (between Medium and Ultra Low)

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Allowable Option (•)

Reduce Static: Allowable Option (•)

Fabric Type: Sportswear

Dry Level (Default): Off

Temp. (Default): Off

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Allowable Option (•)

Reduce Static: Allowable Option (•)

Fabric Type: Denim, towels, heavy cottons

Dry Level (Default): Normal

Dry Level (Allowable Option): Adj.

Temp. (Default): Med. High (between Medium and High)

Wrinkle Care: Not an option.

Damp Dry Signal: Allowable Option (•)

Reduce Static: Not an option.

Fabric Type: For small loads with short drying times

Dry Level (Default): Off

Temp. (Default): High

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Not an option.

Reduce Static: Not an option.

Fabric Type: For items that require heat-free drying such as plastics or rubber

Dry Level (Default): Off

Temp. (Default): No Heat

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Not an option.

Reduce Static: Not an option.

Fabric Type: Comforters, bedding, children’s clothing

Default Time: Off

Temp.: High

Dry Level: Dry

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Not an option.

Reduce Static: Not an option.

Maximum Amount: Single (1 each) for Comforter, Bedding; 3 lbs. for Children’s clothing.

Fabric Type: Comforters, shirts, trousers (except especially delicate fabrics)

Default Time: Off

Temp.: Med. High (between Medium and High)

Dry Level: Dry

Wrinkle Care: Allowable Option (•)

Damp Dry Signal: Not an option.

Reduce Static: Not an option.

Maximum Amount: Single (1 each) for Comforter; 5 each for Shirts*.

*Shirt: 70% cotton, 30% poly blend. Except especially delicate fabrics

Cycle: Reduce Static

Default Time: Follows Selected Cycle

Temp.: Wet

Dry Level: Allowable Option (•)

Wrinkle Care: Not an option.

Damp Dry Signal: Not an option.

Reduce Static: Default setting (=)

Maximum Amount: 8 lbs. (18 Items.)

Cycle: Turbo Steam

Default Time: Follows Selected Cycle

Temp.: Wet

Dry Level: Allowable Option (•)

Wrinkle Care: Not an option.

Damp Dry Signal: Not an option.

Reduce Static: Default setting (=)

Maximum Amount: 8 lbs. (18 Items.)

Cycle: Reduce Static

Default Time: 38 minutes

Temp.: High

Dry Level: Wet

Wrinkle Care: Not an option.

Damp Dry Signal: Not an option.

Reduce Static: Default setting (=)

Maximum Amount: 8 lbs. (18 Items.)

Step 1. Turn on the dryer by pressing the Power button on the LG DLEX4000. The cycle LEDs will illuminate and a chime will sound.

Step 2. Turn the cycle selector knob in either direction until the LED for the desired cycle is on.

Step 3. Press the Start/Pause button to begin the cycle. The cycle can be paused at any time either by opening the door or by pressing the Start/Pause button. If the cycle is not restarted within 14 minutes of being paused, the dryer will shut off and the settings will be lost.

Always make sure the lint filter is clean before starting a new load; a clogged lint filter will increase drying time on the LG DLEX4000. To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Push the lint filter firmly back into place.

Always ensure the lint filter is properly installed before running the dryer. Running the dryer with a loose or missing lint filter will damage the dryer and articles in the dryer.

Check all pockets to make sure that they are empty. Items such as clips, pens, coins, and keys can damage both the dryer and your clothes. Flammable objects such as lighters or matches could ignite, causing a fire.

Never dry clothes that have been exposed to oil, gasoline, or other flammable substances. Washing clothes will not completely remove oil residues.

Combine large and small items in the same load.

Damp clothes will expand as they dry. Do not overload the dryer; clothes require room to tumble and dry properly.

Use mesh laundry bags to separate clothes with zippers, hooks, straps, and drawstrings to prevent them from catching on or tangling with other clothes or damaging the lint filter.

Fabric Care Label Guide for Tumble Dry on LG DLEX4000:

Dry setting applies to: Normal (Work clothes, corduroys, etc.), Heavy Duty (Jeans, heavyweight items), Bedding (Comforters, Pillows, Shirts), Towels (Denim, towels, heavy cottons), Small Load (Only normal & cotton/towels fabric type (Max. 3 lb)), Perm. Press (Permanent press, synthetic items), Delicates (Lingerie, sheets, blouses).

Heat setting corresponding to Dry:

• High: Heavy Duty
• Med. High (between Medium and High): Normal, Towels
• Medium: Bedding, Perm. Press
• Low (between Medium and Ultra Low): Delicates

Gentle/delicate setting applies to: Perm. Press, Delicates.

Do not tumble dry setting applies to: (None explicitly listed for this model/cycle group).

Do not dry (used with do not wash) setting applies to: (None explicitly listed for this model/cycle group).

No heat/air setting applies to: Air Dry.

For Manual Dry Cycles (Speed Dry and Air Dry):

Speed Dry: Dry Level Off, Temp High, Wrinkle Care (•)

Air Dry: Dry Level Off, Temp No Heat, Wrinkle Care (•)

Turn the cycle selector knob in either direction until the LED for the desired cycle is on. The preset temperature, dry level, and option settings for that cycle will be shown. Default settings for the selected cycle can now be changed if desired. Refer to the Cycle Setting and Options page for details.

NOTE: Not all options or modifiers are available on all cycles. Refer to the Cycle Guide page for default settings and available options. A different chime will sound and the LED will not come on if the selection is not available.

Cycle Modifier Buttons on the LG DLEX4000 allow customization of settings for selected cycles:

Dry Level: Use this button to select the level of dryness for the cycle. Press the Dry Level button repeatedly to scroll through available settings. This option is only available with Sensor Dry cycles. The dryer will automatically adjust the cycle time. Selecting dry levels above Normal will increase the cycle time. Selecting dry levels below Normal will decrease the cycle time. Use the dry level between Normal and Damp or the Damp dry level for items that you wish to iron.

Temp.: Use this button to adjust the temperature setting. This allows precise care of fabrics and garments. Press the Temp. button repeatedly to scroll through available settings.

Time Dry: Use this button to manually select the drying time, from 20 to 60 minutes, in 10-minute increments. Use this for small loads or to remove wrinkles. Use the More Time/Less Time buttons to add or reduce the drying time in 5-minute increments.

Signal: The appliance plays a melody when the drying cycle is finished. The buttons make a sound each time a button is pressed. Use this button to turn the melody and button tones on or off. To turn on/off, press the Signal button. When this function is turned on, the On/Off LED on the display lights up.

The LG DLEX4000 features several additional cycle options:

Wrinkle Care: Selecting this option will tumble the load periodically for up to 3 hours after the selected cycle, or until the door is opened. This is helpful in preventing wrinkles when you are unable to remove items from the dryer immediately.

Damp Dry Signal: When this option is selected, the dryer signals when the load is approximately 80% dry. This allows you to remove faster-drying lightweight items or items that you would like to iron or hang while they are still slightly damp. To turn on/off, press the Damp Dry Signal button.

Energy Saver: This option helps to reduce the energy consumption of the Normal Cycle, depending on the load size. When the Energy Saver option is selected, the cycle begins with an air dry section and the drying time is increased.

Some cycle option buttons on the LG DLEX4000 also activate secondary functions marked with an asterisk (*). Press and hold the option button marked with the special function to activate it.

Activating the Control Lock Function: Press and hold the Damp Dry Signal button for 3 seconds.

Drum Light (DLEX4200*, DLGX4201*, DLEX4000*, DLGX4001*, DLEX4500*, DLGX4501*): To turn on the light during a cycle, press and hold the Wrinkle Care button for three seconds.

Do not open the dryer door during steam cycles.

Do not touch the steam nozzle in the drum during or after the steam cycle.

The Steam Fresh™ cycle uses the power of steam to quickly reduce wrinkles and odors in fabrics. It brings new life to wrinkled clothes that have been stored for an extended time and makes heavily wrinkled clothes easier to iron. Steam Fresh™ can also be used to help reduce odors in fabrics.

NOTE: The cycle time depends on the load (number of items). Press the More Time or Less Time button to change the display to reflect the number of items in the load. The display will show 1, 3, or 5 if 3 or fewer items, 5 is for 4 or 5 items, and 6/9 indicates a large load such as a comforter.

The Steam Sanitary™ cycle is ideal for sanitizing non-washable items quickly and easily using the power of steam on the LG DLEX4000.

Use this cycle for cotton and polyester material. (Do NOT use for urethane foam, down feathers or delicate items).

The Reduce Static option on the LG DLEX4000 injects steam late in the drying cycle to reduce the static electricity caused by dry fabrics rubbing together.

NOTE:

When Sensor Dry is selected with the Reduce Static option, the dry levels below Normal cannot be selected.

The Reduce Static option can also be selected during Time Dry cycles.

After the Steam option is selected in Time Dry, the More Time or Less Time buttons will change the steam time ONLY.

Press the More Time or Less Time button to adjust the cycle time depending on the size of the load (7, 9, 11, 14, 16, or 18 items).

Cycle: Steam Sanitary™

Steam: Turbo Steam

Default Time: 31 minutes

Temp.: High

Dry Level: Dry

Fabric State: Dry

Fabric Type: Comforter, Bedding, Children’s clothing

Maximum Amount: Single (1 each) for Comforter, Bedding; 3 lbs. for Children’s clothing.

Cycle: Steam Fresh™

Steam: Turbo Steam

Default Time: 10 minutes

Temp.: Med. High (between Medium and High)

Dry Level: Dry

Fabric State: Dry

Fabric Type: Comforter, Shirts*

Maximum Amount: Single (1 each) for Comforter; 5 each for Shirts*.

*Shirt: 70% cotton, 30% poly blend. Except especially delicate fabrics

Cycle: Reduce Static

Steam: Follows Selected Cycle

Default Time: Follows Selected Cycle

Temp.: Wet

Dry Level: Allowable Option (•)

Fabric State: Wet

Fabric Type: Varies by selected cycle

Maximum Amount: 8 lbs. (18 Items.)

Cycle: Turbo Steam

Steam: Follows Selected Cycle

Default Time: Follows Selected Cycle

Temp.: Wet

Dry Level: Allowable Option (•)

Fabric State: Wet

Fabric Type: Varies by selected cycle

Maximum Amount: 8 lbs. (18 Items.)

Cycle: Reduce Static

Steam: Time Dry

Default Time: 38 minutes

Temp.: High

Dry Level: Wet

Fabric State: Wet

Fabric Type: Varies by selected cycle

Maximum Amount: 8 lbs. (18 Items.)