LG 70UN7370PUB (02) PDF Document

Install your LG 70UN7370PUB where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not install the product on a carpet or cushion. Do not block or cover the product with cloth or other materials while the unit is plugged in. Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device. Do not move the TV whilst the Power cord is plugged in. Do not use a damaged or loosely fitting power cord. Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

When moving or lifting the LG 70UN7370PUB, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size:

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV by hand, hold the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

1. Lift and tilt the TV into its upright position on a table. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

2. Connect the power cord to a wall outlet.

Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product.

If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury.

Do not use any unapproved items to ensure the safety and product life span. Any damage or injuries caused by using unapproved items are not covered by the warranty.

Make sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.) Do not fasten the screws with excessive force otherwise they may strip and become loose.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts, and ropes are not provided. You can obtain additional accessories from your local dealer.

Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount.

Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.

If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.

When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.

Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

The specific VESA dimensions and screw specifications for the LG 70UN7370PUB are:

Connect an antenna, cable, or cable box to watch TV referring to the illustrations on the TV. The illustrations may differ from the actual items and an RF cable is optional.

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

Note that this TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed.

To access this setting, go to [Settings] > [Picture] > [Additional Settings] > [HDMI Ultra HD Deep Color].

On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)

Off: Support 4K @ 50/60 Hz (4:2:0)

If the device connected to the Input Port also supports Ultra HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to off. This feature is available only on certain models which support HDMI Ultra HD Deep Color.

You can simply operate the TV functions using the button located on the TV.

Basic Functions:

Power On: Press the button.

Power Off: Press and Hold the button (All running apps will close).

Menu Control: Press the button while the TV is on (You can access and adjust the menu by pressing the button).

Menu Selection: Press and Hold the button (You can use the function when you access menu control).

Adjusting the Menu:

When the TV is turned on, press the button one time. You can adjust the Menu items using the button.

Power Icon: Turns the power off.

Input Icon: Changes the input source.

Volume Icon (+/-): Adjusts the volume level.

Channel Icon (^/v): Scrolls through the saved channels.

Power: Turns the TV on or off.

TV: Returns to the last TV channel.

Search (Magnifying Glass): Check for recommended content. Shows the search mode.

CC/SUB: Activates or deactivates the subtitles.

Q. Settings (Gear Icon): Accesses the Quick Settings.

Input (Source Icon): Changes the input source.

Number buttons: Enters numbers.

9**: Accesses the [Quick Help].

– (DASH): Inserts a — between numbers such as 2-1 and 2-2.

LIST: Accesses the saved channels list.

… (MORE ACTIONS): Displays more remote control functions.

QUICK ACCESS: Edits QUICK ACCESS. (Feature allowing entry to a specified app or Live TV by pressing and holding number buttons).

+ VOL -: Adjusts the volume level.

FAV: Accesses your favorite channel list.

GUIDE: Displays the program event according to time scheduler.

MUTE (Speaker with X): Mutes all sounds.

MUTE**: Accesses the [Accessibility] menu.

^ CH v: Scrolls through the saved channels.

PAGE: Moves to the previous or next screen.

Streaming Service buttons: Connects to the Video Streaming Service.

HOME (House Icon): Accesses the Home menu.

HOME**: Shows the previous history.

BACK: Returns to the previous screen.

EXIT: Clears on-screen displays and returns to last input viewing.

Navigation button (up/down/left/right): Scrolls through menus or options.

OK (Center button): Selects menus or options and confirms your input.

INFO: Shows information on the current program.

SAP: Enables SAP (Secondary Audio Program) Feature.

REC: Starts to record. (Only Time MachineReady supported model).

Control buttons (Play, Pause, etc.): Control buttons for media contents.

Colored buttons (Red, Green, Yellow, Blue): These access special functions in some menus.

** To use the button, press and hold for more than 1 second.

Power: Turns the TV on or off.

STB POWER: You can turn your set-top box on or off by adding the set-top box to the universal remote control for your TV.

Number buttons: Enters numbers.

9**: Accesses the [Quick Help].

– (DASH): Inserts a — between numbers such as 2-1 and 2-2.

LIST: Accesses the saved channels list.

… (MORE ACTIONS): Displays more remote control functions.

QUICK ACCESS: Edits QUICK ACCESS.

AD/SAP**: SAP (Secondary Audio Program) Feature can also be enabled by pressing the … button.

Volume (+/-): Adjusts the volume level.

MUTE: Mutes all sounds.

MUTE**: Accesses the [Accessibility] menu.

CH (^/v): Scrolls through the saved channels.

Voice recognition: Network connection is required. Speak while pressing and holding the button to use the voice recognition feature.

HOME: Accesses the Home menu.

HOME**: Shows the previous history.

Q. Settings (Gear Icon): Accesses the Quick Settings.

Q. Settings**: Displays the [All Settings] menu.

Wheel (OK): Press the center of the Wheel button to select a menu. You can change channels by using the wheel button.

Navigation (up/down/left/right): Press the buttons to scroll the menu. If you press buttons while the pointer is in use, the pointer will disappear and the Magic Remote will operate like a general remote.

BACK: Returns to the previous screen.

BACK**: Clears on-screen displays and returns to last input viewing.

GUIDE: Displays the program event according to time scheduler.

Streaming Service buttons: Connects to the Video Streaming Service.

INPUT: Changes the input source.

INPUT**: Accesses the [Home Dashboard].

Colored buttons: These access special functions in some menus.

Control buttons: Controls media contents.

** To use the button, press and hold for more than 1 second.

How to register the Magic Remote Control:

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control:

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

If you cannot control the TV with the remote control:

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

No image display and no sound is produced:

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

The TV turns off suddenly:

Check the power control settings. The power supply may be interrupted.

Check if the auto-off function is activated in the settings menu.

If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

Abnormal Display:

If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal; there is nothing wrong with TV.

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance.

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

Displaying a still image for a prolonged period of time may cause an image sticking. Avoid displaying a fixed image on the TV screen for an extended length of time.

Connect the USB to Serial (RS-232C) converter/RS-232C (Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

USB to Serial(RS-232C) converter with USB Cable:

LG TV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial(RS-232C) converter which is not made nor provided by LG.

RS-232C(Serial) With RS-232C(Serial) Cable:

DE9 (D-Sub 9pin) Type: You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C(Serial) cable required for the connection between the PC and the TV.

Phone jack Type:

You need to purchase the phone-jack to RS-232C cable required for the connection between the PC and the TV.

Communication Parameters:

Baud rate: 9600 bps (UART)

Data length: 8 bits

Parity: None

Stop bit: 1 bit

Communication code: ASCII code

Use a crossed (reverse) cable.

The following table lists the available commands for external control. Note that during playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG.