LG 65UN7310PUC (01) PDF Document

When moving or lifting the LG 65UN7310PUC, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size:

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV by hand, hold the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

1. Lift and tilt the LG 65UN7310PUC into its upright position on a table.

2. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. Doing so may damage the product.

If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury.

Do not use any unapproved items to ensure the safety and product life span.

Make sure that the screws are fastened tightly. If they are not fastened securely enough, the TV may tilt forward after being installed. Do not fasten the screws with excessive force otherwise they may strip and become loose.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

Connect an antenna, cable, or cable box to watch TV while referring to the following:

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

This TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed.

Navigate to [Picture] -> [Additional Settings] -> [HDMI Ultra HD Deep Color].

Select “On” if the device connected to the Input Port supports Ultra HD Deep Color. Your picture may be clearer.

Select “Off” if the device doesn’t support it, as it may not work properly.

Note: This feature is available only on certain models which support HDMI Ultra HD Deep Color.

You can operate the TV functions using the button located on the TV:

Power On: Press the button.

Power Off: Press and hold the button (All running apps will close).

Menu Control: Press the button while the TV is on.

Menu Selection: Press and hold the button.

You can access and adjust the menu by pressing the button when the TV is on to Turn the power off, Change the input source, Adjust the volume level, or Scroll through the saved channels.

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth.

Do not spray water or other liquids directly on the TV.

Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

Make sure to wring any excess water or cleaner from the cloth.

Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

When cleaning the product, be careful not to allow any liquid or foreign objects to enter the gap between the upper, left or right side of the panel and the guide panel.

Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

If using USB to Serial(RS-232C) converter with USB Cable, connect the USB end to the TV (LG TV supports PL2303 chip-based converters).

If using RS-232C(Serial) with RS-232C(Serial) Cable, connect the DE9 (D-Sub 9pin) or Phone jack type depending on your TV model.

Note: The type of control port on the TV can be different between model series. Cables are not provided.

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General -> About this TV or OPTION) and press OK.

3. Press the Navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

5. When you are finished, press EXIT.