LG 65UN7300PUC (02) PDF Document

When moving or lifting the LG 65UN7300PUC, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV by hand, hold the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Note: Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. Doing so may damage the product. If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury. Do not use any unapproved items to ensure the safety and product life span. Any damage or injuries caused by using unapproved items are not covered by the warranty. Make sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.) Do not fasten the screws with excessive force otherwise they may strip and become loose.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

When mounting the LG 65UN7300PUC to a wall, use screws and a wall mount bracket that meet the VESA standard. The standard dimensions for the wall mount kits are as follows:

Connect an antenna, cable, or cable box to watch TV while referring to the illustrations provided in the manual. The RF cable is optional.

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

DTV Audio Supported Codec: MPEG, Dolby Digital.

If the device connected to the Input Port supports Ultra HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to off.

To access this setting, go to: [Settings] (Gear Icon) -> [Picture] -> [Additional Settings] -> [HDMI Ultra HD Deep Color].

The specifications for the LG 65UN7300PUC (UN73 Series) are:

On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)

Off: Support 4K @ 50/60 Hz (4:2:0)

You can simply operate the TV functions using the button located on the TV.

Power On: Press the button.

Power Off: Press and Hold the button (All running apps will close).

Menu Control: Press the button while the TV is on (You can access and adjust the menu by pressing the button when TV is on).

Menu Selection: Press and Hold the button (You can use the function when you access menu control).

When the TV is turned on, press the button one time. You can adjust the Menu items using the button:

Power Icon: Turns the power off.

Inputs Icon: Changes the input source.

Plus/Minus Icon: Adjusts the volume level.

Up/Down Icon: Scrolls through the saved channels.

How to register the Magic Remote Control:

To use the Magic Remote, first pair it with your TV.

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control:

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

For more information about this TV, read the USER GUIDE embedded in the product.

To open the USER GUIDE: Go to [Settings] (Gear Icon) -> [Support] -> [User Guide].

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

Check the power control settings. The power supply may be interrupted.

Check if the auto-off function is activated in the settings menu.

If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth.

Do not spray water or other liquids directly on the TV.

Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

Make sure to wring any excess water or cleaner from the cloth.

Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

USB to Serial(RS-232C) converter with USB Cable: LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial(RS-232C) converter which is not made nor provided by LG.

RS-232C(Serial) With RS-232C(Serial) Cable: DE9 (D-Sub 9pin) Type. You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C(Serial) cable required for the connection between the PC and the TV.

Phone jack Type: You need to purchase the phone-jack to RS-232C cable required for the connection between the PC and the TV. For other models, connect to the USB port. The connection interface may differ from your TV.

Communication Parameters:

Baud rate: 9600 bps (UART)

Data length: 8 bits

Parity: None

Stop bit: 1 bit

Communication code: ASCII code

Use a crossed (reverse) cable.

Transmission: [Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command 1]: First command to control the TV. (j, k, m or x)

[Command 2]: Second command to control the TV.

[Set ID]: You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled. * [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on transmission/receiving protocol.

[DATA]: To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.

[Cr]: Carriage Return – ASCII code ‘0x0D’

[ ]: Space – ASCII code ‘0x20’

OK Acknowledgement: [Command2][ ][Set ID][ ][OK][Data][x]

The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

Error Acknowledgement: [Command2][ ][Set ID][ ][NG][Data][x]

The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors.

Data 00: Illegal Code

When you enter the [data] in hexadecimal, refer to following conversion table.

00 : Step 0

01 : Step 1 (Set ID 1)

0A : Step 10 (Set ID 10)

0F : Step 15 (Set ID 15)

10 : Step 16 (Set ID 16)

32 : Step 50 (Set ID 50)

33 : Step 51 (Set ID 51)

63 : Step 99 (Set ID 99)

C7 : Step 199

C8 : Step 200

FE : Step 254

FF : Step 255

01 00 : Step 256

27 0E : Step 9998

27 0F : Step 9999