LG 65NANO91 (01) PDF Document

To reduce the risk of fire and electric shock, do not expose the LG 65NANO91 TV to rain or moisture. To prevent the spread of fire, keep candles or other items with open flames away from this product at all times.

Installation Environments:

Do not place the TV and/or remote control in the following environments:

• Keep the product away from direct sunlight.

• An area with high humidity such as a bathroom.

• Near any heat source such as stoves and other devices that produce heat.

• Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

• An area exposed to rain or wind.

• Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).

• Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

• Do not install in excessively dusty places.

Ventilation:

• Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase.

• Do not install the product on a carpet or cushion.

• Do not block or cover the product with cloth or other materials while the unit is plugged in.

• Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

Power Cord:

• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

• Do not move the TV whilst the Power cord is plugged in.

• Do not use a damaged or loosely fitting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

General Safety:

• Do not let your children climb or cling onto the TV. The TV may fall over, which may cause serious injury.

• If an outdoor antenna is installed, it should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.

• A TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet. Ensure you connect the earth ground wire to prevent possible electric shock.

• Never touch this apparatus or antenna during a lightning storm.

• Do not insert metallic or inflammable objects into the product.

• Do not touch the end of the power cord while it is plugged in.

• Do not use high voltage electrical equipment near the TV (e.g., a bug zapper).

• Use only authorized attachments/accessories approved by LG Electronics.

• Never disassemble the AC adapter or power cord.

• Handle the adapter carefully to avoid dropping or striking it.

• To reduce the risk of fire or electrical shock, do not touch the TV with wet hands.

If any of the following occur, unplug the product immediately and contact your local customer service:

• The product has been damaged.

• If water or another substance enters the product (like an AC adapter, power cord, or TV).

• If you smell smoke or other odors coming from the TV.

• During lightning storms or when unused for long periods of time.

Even if the TV is turned off by remote control or button, the AC power source is still connected to the unit if it is not unplugged.

• Store the accessories (battery, etc.) in a safe location out of the reach of children.

• Do not short circuit, disassemble, or allow the batteries to overheat.

• Do not dispose of batteries in a fire.

• Batteries should not be exposed to excessive heat.

• Caution: Risk of fire or explosion if the battery is replaced by an incorrect type.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

• If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes.

• The image shown may differ from your TV.

• Your TV’s OSD (On Screen Display) may differ slightly from that shown in the manual.

• The available menus and options may differ from the input source or product model that you are using.

• New features may be added to this TV in the future.

• The device must be easily accessed to a location outlet near the access. Some devices are not made by turning on/off button, turning off the device and unplugging the power cord.

• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.

• Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.

• Recommended HDMI Cable Type: Ultra High Speed HDMI®/™ cable (3 m or less).

Make sure to use screws and a wall mount bracket that meet the VESA standard. The standard dimensions for the wall mount kits for the LG 65NANO91 and similar models are described in the following table:

Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation:

• It is recommended to move the TV in the box or packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

• Avoid touching the screen at all times, as this may result in damage to the screen.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV by hand, hold the TV upright.

• When transporting the TV, do not expose the TV to jolts or excessive vibration.

• When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause flexing/bending of the frame chassis as it may damage the screen.

• When handling the TV, be careful not to damage the protruding buttons.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a 10 cm (minimum) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Note: When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts already inserted at the eye-bolts position, remove those bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Additional Precautions:

• Use a platform or cabinet that is strong and large enough to support the TV securely.

• Brackets, bolts, and ropes are not provided. You can obtain additional accessories from your local dealer.

• Make sure that the screws are inserted correctly and fastened securely. If they are not fastened securely enough, the TV may tilt forward after being installed. Do not use too much force and over-tighten the screws; otherwise, the screw may be damaged and not tighten correctly.

Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer.

• Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.

• If you intend to mount the product to a wall, attach the VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.

• When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.

• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

• When installing the wall mounting bracket, it is recommended to cover the stand hole using tape, in order to prevent the influx of dust and insects (depending on model).

Antenna/Cable:

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs.

• If the image quality is poor, install a signal amplifier properly to improve the image quality.

• If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.

• An antenna cable and converter are not supplied.

Satellite Dish (Depending on model):

Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω).

HDMI Connection:

For the best picture and audio quality, connect the external device and the TV with an HDMI cable. A separate cable is not provided.

• When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

• To enable higher quality formats, you may need to adjust the [HDMI Ultra HD Deep Colour] setting. Navigate to Settings → Picture → Additional Settings → HDMI Ultra HD Deep Colour.

For models like the LG 65NANO91:

On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0), and for ports 3 & 4, 4K @ 100/120 Hz (4:4:4, 4:2:2, 4:2:0).

Off: Support 4K @ 50/60 Hz (4:2:0).

If the device connected to the Input Port also supports Ultra HD Deep Colour, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Colour] setting to Off.

USB Connection:

Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the USB port on the TV directly.

General External Device Tips:

• Connect external devices to the TV regardless of the order of the TV port.

• If you record a TV program on a Blu-ray/DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR.

• If you connect a gaming device to the TV, use the cable supplied with the gaming device.

• In PC mode, if noise is present, change the PC output to another resolution, change the refresh rate, or adjust the brightness and contrast on the [Picture] menu until the picture is clear.

You can simply operate the TV functions using the button on the TV.

Basic Functions:

• Power On: Press the button.

• Power Off: Press and hold the button.

• Menu Control: Press the button when the TV is on.

• Menu Selection: Press and hold the button when in the menu.

Adjusting the Menu:

When the TV is turned on, press the button one time. You can adjust the Menu items using the button as follows:

• (POWER): Turns the TV on or off.

• (STB POWER): Turns your set-top box on or off.

• Number buttons: Enters numbers.

• – (DASH): Inserts a dash between numbers such as 2-1 and 2-2.

• LIST: Accesses the saved programmes list.

• … (MORE ACTIONS): Displays more remote control functions.

• QUICK ACCESS (Press and hold number button): Enters a specified app or Live TV directly.

• AD/SAP: Enables the audio descriptions function.

• + / –: Adjusts the volume level.

• (MUTE): Mutes all sounds. Press and hold to access the [Accessibility] menu.

• ^ / v: Scrolls through the saved programmes.

• (Voice recognition): A network connection is required. Press and hold the button to use the voice recognition feature.

• (HOME): Accesses the Home menu. Press and hold to show previous history.

• (Q. Settings): Accesses the Quick Settings. Press and hold to display the [All Settings] menu.

• Wheel (OK): Press the center of the button to select a menu. You can change programmes by using the wheel.

• (up/down/left/right): Press to scroll the menu. If you press these buttons while the pointer is in use, the pointer will disappear and the remote will operate like a general remote control. To display the pointer again, shake the remote left and right.

• (BACK): Returns to the previous level. Press and hold to clear on-screen displays and return to the last input viewing.

• GUIDE: Shows the programme guide.

• Streaming Service buttons: Connects to the Video Streaming Service.

• (INPUT): Changes the input source. Press and hold to access the [Home Dashboard].

• Red/Green/Yellow/Blue buttons: These access special functions in some menus.

• REC: Runs the record function.

• (Control buttons): Controls media contents.

How to register the Magic Remote Control:

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) button on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control:

Press the (BACK) and (HOME) buttons at the same time for five seconds to unpair the Magic Remote with your TV.

To disconnect and re-register the Magic Remote at the same time, press and hold the GUIDE button for more than 5 seconds.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote control.

• Check if the batteries are still working and properly installed (positive to positive, negative to negative).

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

• Check the power control settings. The power supply may be interrupted.

• Check if the auto-off function is activated on the settings related time.

• If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

• Turn the TV off/on using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.

• “Flicker”: If the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal; there is nothing wrong with the product.

• Tiny dots: This panel is an advanced product that contains millions of pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product. This phenomenon also occurs in third-party products and is not subject to exchange or refund.

• Different brightness/color: You may find different brightness and colour of the panel depending on your viewing position (left/right/top/down). This phenomenon occurs due to the characteristic of the panel. It is not related to product performance and is not a malfunction.

Displaying a still image for a prolonged period of time may cause image sticking, where a faint version of the image remains on the screen. Avoid displaying a fixed image on the TV screen for a long period of time to prevent this.

• “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

• Electrical circuit humming/panel buzzing: A low-level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

Broadcasting Specifications (Depending on country)

Wireless Module (LGSBWAC92) Specifications (Except for NANO79*, NANO80*, NANO81*)

Environment condition

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.