LG 55UN7300PUC (02) PDF Document

To ensure proper ventilation for the LG 55UN7300PUC, follow these guidelines:

Do not install the TV in a confined space such as a bookcase.

Do not install the product on a carpet or cushion.

Do not block or cover the product with cloth or other materials while the unit is plugged in.

When moving or lifting the LG 55UN7300PUC, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size:

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV by hand, hold the TV upright; never turn the TV on its side or tilt towards the left or right.

When transporting the TV, do not expose the TV to jolts or excessive vibration.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

Step 1. Lift and tilt the TV into its upright position on a table.

Step 2. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

Step 3. Connect the power cord to a wall outlet.

Note: Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. Doing so may damage the product.

Step 1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

Step 2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

Step 3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts, and ropes are not provided. You can obtain additional accessories from your local dealer.

Make sure to use screws and a wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits for the LG 55UN7300PUC are described in the following table:

Connect an antenna, cable, or cable box to the TV while referring to the following:

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

This TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed.

To adjust the HDMI Ultra HD Deep Color settings, navigate to [Settings] > [Picture] > [Additional Settings] > [HDMI Ultra HD Deep Color].

On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)

Off: Support 4K @ 50/60 Hz (4:2:0)

If the device connected to the Input Port also supports Ultra HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to off.

You can operate the TV functions using the button located on the device.

When the TV is turned on, press the button one time to adjust the Menu items:

Power Circle Icon: Turns the power off.

Input Icon: Changes the input source.

Plus/Minus Icons: Adjusts the volume level.

Up/Down Icons: Scrolls through the saved channels.

To use the Magic Remote, first pair it with your TV.

Step 1. Put batteries into the Magic Remote and turn the TV on.

Step 2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

Check the power control settings. The power supply may be interrupted.

Check if the auto-off function is activated in the settings menu.

If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth.

Do not spray water or other liquids directly on the TV.

Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel.

Make sure to wring any excess water or cleaner from the cloth.

Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

USB to Serial(RS-232C) converter with USB Cable: Connect the USB end to the TV (USB IN) and the RS-232C end to the PC.

RS-232C(Serial) With RS-232C(Serial) Cable (DE9/D-Sub 9pin Type): You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C(Serial) cable required for the connection between the PC and the TV.

Phone jack Type: You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and the TV.

Baud rate: 9600 bps (UART)

Data length: 8 bits

Parity: None

Stop bit: 1 bit

Communication code: ASCII code

Use a crossed (reverse) cable.

Step 1. Press SETTINGS to access the main menus.

Step 2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.

Step 3. Press the Navigation buttons to scroll to SET ID and press OK.

Step 4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

Step 5. When you are finished, press EXIT.