LG 55NANO80 (01) PDF Document

To reduce the risk of fire and electric shock, do not expose this product to rain or moisture. To prevent the spread of fire, keep candles or other items with open flames away from this product at all times.

Do not place the TV and/or remote control in the following environments:

• Keep the product away from direct sunlight.

• An area with high humidity such as a bathroom.

• Near any heat source such as stoves and other devices that produce heat.

• Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

• An area exposed to rain or wind.

• Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).

• Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

• Do not install in excessively dusty places.

Otherwise, this may result in fire, electric shock, combustion/explosion, malfunction or product deformation.

• Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase.

• Do not install the product on a carpet or cushion.

• Do not block or cover the product with cloth or other materials while the unit is plugged in.

• Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

• Do not move the TV whilst the Power cord is plugged in.

• Do not use a damaged or loosely fitting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

• The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.

• Make sure the power cord is connected securely to the TV and wall socket. If not secured, damage to the Plug and socket may occur and in extreme cases a fire may break out.

• Do not touch the end of the power cord while it is plugged in. You may be electrocuted.

If any of the following occur, unplug the product immediately and contact your local customer service:

• The product has been damaged.

• If water or another substance enters the product (like an AC adapter, power cord, or TV).

• If you smell smoke or other odors coming from the TV.

• During lightning storms or when unused for long periods of time.

Even if the TV is turned off by remote control or button, the AC power source is connected to the unit if not unplugged.

• Store the accessories (battery, etc.) in a safe location out of the reach of children.

• Do not short circuit, disassemble, or allow the batteries to overheat. Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat.

• Caution: Risk of fire or explosion if the battery is replaced by an incorrect type.

• When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV.

• Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

• When cleaning the product, be careful not to allow any liquid or foreign objects to enter the gap between the upper, left or right side of the panel and the guide panel.

• Make sure to wring any excess water or cleaner from the cloth.

• Do not spray water or cleaner directly onto the TV screen.

• Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.

It is recommended to use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur. The recommended cable type is an Ultra High Speed HDMI®/™ cable (3 m or less).

Separate purchase items can be changed or modified for quality improvement. These devices only work with certain models.

Magic Remote Control

Model: MR20GA. Check whether your TV model supports Bluetooth in the Wireless Module Specification to verify whether it can be used with the Magic Remote.

Wall Mounting Bracket

Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.

Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation.

• It is recommended to move the TV in the box or packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV by hand, hold the TV upright.

• When transporting the TV, do not expose the TV to jolts or excessive vibration.

• When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause flexing / bending of frame chassis as it may damage screen.

• When handling the TV, be careful not to damage the protruding buttons.

• Avoid touching the screen at all times, as this may result in damage to the screen.

• When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a 10 cm (minimum) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

• Use a platform or cabinet that is strong and large enough to support the TV securely.

• Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer.

• Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.

• For more information on screws and wall mount bracket, refer to the Separate Purchase section.

• If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.

• When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.

• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

• When installing the wall mounting bracket, it is recommended to cover the stand hole using tape, in order to prevent the influx of dust and insects. (Depending on model)

Antenna/Cable

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs.

• If the image quality is poor, install a signal amplifier properly to improve the image quality.

• If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.

• An antenna cable and converter are not supplied.

Satellite dish (Depending on model)

Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω).

HDMI

For the best picture and audio quality, connect the external device and the TV with an HDMI cable. Some separate cable is not provided.

• When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

• Supported HDMI Audio formats include: True HD (48 kHz), Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz), PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz).

• To enable higher quality signals, navigate to → → [Picture] → [Additional Settings] → [HDMI Ultra HD Deep Colour].

(For NANO79*, NANO80*, NANO81*)

– On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)

– Off: Support 4K @ 50/60 Hz (4:2:0)

(Except for NANO79*, NANO80*, NANO81*)

– On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0), <3,4 port Only> 4K @ 100/120 Hz (4:4:4, 4:2:2, 4:2:0)

– Off: Support 4K @ 50/60 Hz (4:2:0)

• If the device connected to Input Port also supports Ultra HD Deep Colour, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Colour] setting to off.

USB

Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the USB port on the TV directly.

You can simply operate the TV functions using the button.

Basic functions:

• Power On (Press)

• Power Off (Press and Hold)

• Menu Control (Press when TV is on)

• Menu Selection (Press and Hold to select)

Adjusting the menu:

When the TV is turned on, press the button one time. You can adjust the Menu items using the button.

The descriptions in this manual are based on the buttons on the remote control. Be sure to point the magic remote toward the remote control sensor on the TV. To use a button function that is marked with **, press and hold for more than 1 second.

• (POWER): Turns the TV on or off.

• (STB POWER): Turns your set-top box on or off (when added to universal remote control).

• Number buttons: Enters numbers.

• 9**: Accesses the [Quick Help].

• – (DASH): Inserts a – between numbers such as 2-1 and 2-2.

• LIST: Accesses the saved programmes list.

• … (MORE ACTIONS): Displays more remote control functions.

• QUICK ACCESS**: Edits QUICK ACCESS, a feature to enter a specified app or Live TV directly.

• AD/SAP**: Enables the audio descriptions function.

• + / –: Adjusts the volume level.

• (MUTE): Mutes all sounds.

• (MUTE)**: Accesses the [Accessibility] menu.

• ^ / v: Scrolls through the saved programmes.

• (Voice recognition): Network connection is required. Check for recommended content.

• (Voice recognition)**: Speak while pressing and holding the button to use the voice recognition feature.

• (HOME): Accesses the Home menu.

• (HOME)**: Shows the previous history.

• (Q. Settings): Accesses the Quick Settings.

• (Q. Settings)**: Displays the [All Settings] menu.

• Wheel (OK): Press the center of the button to select a menu. You can change programmes by using this button.

• △▽◁▷(up/down/left/right): Press the up, down, left or right button to scroll the menu. If you press these buttons while the pointer is in use, the pointer will disappear and the remote will operate like a general remote. To display the pointer again, shake the Magic Remote.

• (BACK): Returns to the previous level.

• (BACK)**: Clears on-screen displays and returns to last input viewing.

• GUIDE: Shows programme guide.

• Streaming Service buttons: Connects to the Video Streaming Service.

• RECENTS: Shows the previous history.

• (INPUT): Changes the input source.

• (INPUT)**: Accesses the [Home Dashboard].

• STB MENU: Displays the set-top box Home menu.

• Red/Green/Yellow/Blue buttons: These access special functions in some menus.

• REC button: Runs the record function.

• ▷,|| (Control buttons): Controls media contents.

How to register the Magic Remote Control

To use the Magic Remote, first pair it with your TV.

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control

Press the (BACK) and (HOME) buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Press and hold the GUIDE button for more than 5 seconds to disconnect and re-register the Magic Remote at the same time.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote control.

• Check if the batteries are still working and properly installed (+ to +, – to -).

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

• Check the power control settings. The power supply may be interrupted.

• Check if the auto-off function is activated on the settings related time.

• If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

• Turn the TV off/on using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.

• If the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with product.

• This panel is an advanced product that contains millions of pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product. This phenomenon also occurs in third-party products and is not subject to exchange or refund.

• You may find different brightness and colour of the panel depending on your viewing position(left/right/top/down). This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction.

• Displaying a still image for a prolonged period of time may cause image sticking. Avoid displaying a fixed image on the TV screen for a long period of time.

• “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

• Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

The specifications vary depending on the model group.

For NANO79*, NANO80*, NANO81* (Module LGSBWAC02):

Except for NANO79*, NANO80*, NANO81* (Module LGSBWAC92):

As band channels can vary per country, the user cannot change or adjust the operating frequency. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.