LG 32LF595B (02) PDF Document

The following items are included with your LG 32LF595B television:

• Television

• Remote Control

• AAA Batteries

• Owner’s Manuals/Guides

• Stand components

• Screws for stand assembly (a x 4, M4 x L20)

• Cable management tie

Please follow these steps to assemble the stand for your LG 32LF595B TV:

1. Lay the TV screen-down on a cushioned surface to prevent scratches.

2. Align the two stand feet with the mounting slots on the bottom of the television.

3. Insert and tighten the four provided ‘a’ screws (M4 x L20) to secure the stand feet to the TV.

4. Carefully lift the TV to an upright position on a flat, stable surface.

To install the batteries in your remote control:

1. Press and slide the battery cover on the back of the remote to open it.

2. Insert two 1.5V AAA batteries, ensuring you match the (+) and (-) ends to the labels inside the compartment.

3. Slide the battery cover back into place until it clicks.

To remove the batteries, perform the installation actions in reverse. It is recommended not to mix old and new batteries, as this may damage the remote control.

After assembling the stand and installing the batteries in the remote:

1. Connect the power cord from the back of the TV to a wall outlet.

2. Press the power button on the remote control. The LG logo will appear on the screen, and the TV will turn on.

You can use the included cable management tie to bundle the cables together behind the TV. This helps to keep them neat and organized.

The full user guide is available electronically on your LG 32LF595B TV. You can access it by pressing the user guide button (indicated by a question mark icon inside a book symbol) on your remote control. This will open the “Safety and Reference” guide on the screen.

The descriptions are based on the standard remote control. Your specific remote may vary.

• (POWER): Turns the TV on or off.

• INPUT: Changes the input source.

• CAPTION: Activates or deactivates subtitles.

• (User Guide): Accesses the on-screen user guide.

• RATIO: Resizes an image.

• TV: Returns to the last TV channel.

• Number button: Enters numbers.

• – (Dash): Inserts a dash between numbers (e.g., 2-1).

• LIST: Accesses the saved channel list.

• FLASHBK: Alternates between the two last channels selected.

• + VOL –: Adjusts the volume level.

• FAV: Accesses your favorite channel list.

• INFO: Shows information on the current program.

• MUTE: Mutes all sounds.

• CH (up/down arrows): Scrolls through the saved channels.

• PAGE (up/down arrows): Moves to the previous or next screen.

You can use the joystick button located on the TV to perform basic functions.

Basic Functions:

• Power On: When the TV is off, press the joystick button once and release it.

• Power Off: When the TV is on, press and hold the joystick button for a few seconds and release it.

• Volume Control: Move the joystick left or right to adjust the volume.

• Channels Control: Move the joystick up or down to change the channel.

Adjusting the Menu:

When the TV is on, press the joystick button once to open a menu. You can then navigate the menu items by moving the joystick up, down, left, or right.

• Turns the power off.

• Accesses the quick settings.

• Clears on-screen displays and returns to TV viewing.

• Changes the input source.

The LG 32LF595B has two main panels of connections:

Side Panel:

• HDMI IN 1 (ARC): For connecting high-definition devices like Blu-ray players, game consoles, or laptops. This port also supports Audio Return Channel (ARC).

• HDMI IN 2: A second HDMI input.

• USB IN 1 & 2: For connecting USB storage devices (flash drives, external hard drives) or a USB hub.

Rear Panel:

• ANTENNA/CABLE IN: For connecting an over-the-air antenna or a cable TV line.

• LAN: For connecting to a wired network for internet access.

• COMPONENT IN / AV IN: For connecting devices using component (Y, PB, PR) or composite (Video) cables, with corresponding L/R audio inputs.

• OPTICAL DIGITAL AUDIO OUT: For connecting to an external audio system, like a soundbar or home theater receiver.

• SERVICE ONLY: This port is for use by service technicians only.

For an optimal connection, it is recommended to use cables that meet the following dimensions:

• HDMI and USB cables should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) wide.

• It is recommended to use certified High-Speed HDMI cables that are 3 meters (about 10 feet) or less in length.

If a USB cable or flash drive does not fit into your TV’s USB port, use an extension cable that supports USB 2.0.

To clean your TV safely, follow these instructions:

1. First, make sure to turn the power off and disconnect the power cord and all other cables.

2. For the screen, frame, cabinet, and stand: To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth. To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent, then wipe immediately with a dry cloth.

3. For the power cord: Remove any accumulated dust or dirt from the power cord regularly.

CAUTION:

• Do not push, rub, or hit the surface with your fingernail or a sharp object.

• Do not spray liquid directly onto the TV surface.

• Do not use chemicals like waxes, benzene, alcohol, thinners, insecticides, or lubricants, as they can damage the screen’s finish.

To prevent damage and ensure safe transportation, follow these guidelines:

• Before moving, disconnect the power cord and all cables.

• It is best to move the TV in its original box or packing material.

• When holding the TV, the screen should face away from you to avoid damage.

• Firmly hold the top and bottom of the TV frame. Do not hold the transparent part, speaker, or speaker grille area.

• When transporting the TV, keep it upright. Do not turn it on its side or tilt it.

• Avoid exposing the TV to jolts or excessive vibration during transport.

• Be careful not to damage the protruding joystick button.

• Avoid touching the screen at all times, as this may result in damage.

1. After attaching the stand, lift and tilt the TV into its upright position on a sturdy, stable table.

2. For proper ventilation, ensure there is a minimum of 10 cm (4 inches) of space between the TV and the wall.

3. Connect the power cord to a wall outlet.

CAUTION: Do not place the TV near or on sources of heat, as this may result in fire or other damage.

An optional wall mount can be used with your TV. Consult your local dealer for a wall mount that supports the VESA standard used by your TV model. Carefully attach the wall mount bracket to the rear of the TV and install it on a solid wall perpendicular to the floor.

VESA Specifications for LG 32LF595B:

• VESA (A x B): 200 x 200 mm

• Standard screw: M6

• Number of screws: 4

• Optional wall mount bracket: LSW240B, MSW240

CAUTION:

• Disconnect the power before moving or installing the TV.

• Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.

• Do not overtighten the screws, as this may cause damage to the TV and void your warranty.

• Use screws and wall mounts that meet the VESA standard. Any damages or injuries from misuse or an improper accessory are not covered.

If a fixed image is displayed on the TV screen for a long period, it can become imprinted and result in a permanent disfigurement known as image burn or burn-in. To prevent this:

• Avoid displaying a fixed image on the screen for a long period of time (2 or more hours).

• If the aspect ratio of the TV is set to 4:3 for a long period, image burn may occur on the letterboxed areas of the screen.

The LG 32LF595B qualifies for ENERGY STAR in its factory default (Home Configuration) setting. Changing the factory default settings or enabling other features may increase power consumption beyond the limits necessary to qualify for ENERGY STAR.

Please adhere to the following safety precautions:

• Read, keep, and follow all instructions and heed all warnings.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other heat-producing apparatus.

• Protect the power cord from being walked on or pinched.

• Only use attachments/accessories specified by the manufacturer.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel.

• Do not press strongly on the panel with a hand or sharp object.

• Ensure the unit is properly grounded if it has a three-prong plug.

• Keep the product away from direct sunlight and do not expose it to rain or moisture.