LG 32LF5800 (02) PDF MANUAL

Clean your TV regularly to keep it at peak performance and to extend the product lifespan.

To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.

To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth.

Do not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in scratches on the screen and image distortions.

Do not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air fresheners, or lubricants, as these may damage the screen’s finish and cause discoloration.

Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.

Remove the accumulated dust or dirt on the power cord regularly.

When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and all cables.
• When holding the TV, the screen should face away from you to avoid damage.
• Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.
• Use at least two people to move a large TV.
• When transporting the TV by hand, hold the TV.
• When transporting the TV, do not expose the TV to jolts or excessive vibration.
• When transporting the TV, keep the TV upright; never turn the TV on its side or tilt towards the left or right.
• When handling the TV, be careful not to damage the protruding joystick button.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

Do not move the TV by holding the cable holder or cable management, as the cable holders may break, and injuries and damage to the TV may occur.

You can operate the TV by pressing the button or moving the joystick left, right, up, or down.

When the TV is turned off, place your finger on the joystick button, press it once and release it.

When the TV is turned on, place your finger on the joystick button, press it once for a few seconds, and release it.

Place your finger on the joystick button and move it left or right to adjust the volume level.

Place your finger on the joystick button and move it up or down to adjust the channel.

When the TV is turned on, press the joystick button one time. You can adjust the menu items moving the joystick button up, down, left, or right.

Turns the power off.

Accesses the main menu.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

1. Lift and tilt the TV into its upright position on a table.

– Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation.

2. Connect the power cord to a wall outlet.

Do not place the TV near or on sources of heat, as this may result in fire or other damage.

The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com. Connect the Kensington security system cable between the TV and a table.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV.

– If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope or cable. Make sure to keep the rope parallel to the flat surface.

Make sure to use screws and wall mounts that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table:

• Disconnect the power before moving or installing the TV. Otherwise electric shock may occur.
• Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.
• If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel. When using a third-party wall mount, it is not covered by the warranty.
• Do not overtighten the screws as this may cause damage to the TV and void your warranty.
• Use the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

Connect an antenna, cable, or cable box to watch TV. The RF cable may not be supplied, depending upon the model.

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external device’s connection, refer to the manual provided with each device.

If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the connected device.

The external device connections may differ from the model.

Connect external devices to the TV regardless of the order of the TV port.

If you connect a gaming device to the TV, use the cable supplied with the gaming device.

Refer to the external equipment’s manual for operating instructions.

In PC mode, there may be noise associated with the resolution, vertical pattern, contrast, or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.

Depending upon the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.

To install batteries, open the battery cover, replace batteries (1.5 V AAA) matching the + and – ends to the label inside the compartment, and close the battery cover. Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution. To remove the batteries, perform the installation actions in reverse. This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor.

• (POWER) Turns the TV on or off.
• CAPTION Activates or deactivates the subtitles.
• AV MODE Selects an AV mode.
• RATIO Resizes an image.
• INPUT Changes the input source.
• Number button Enters numbers.
• – (Dash) Inserts a dash between numbers such as 2-1 and 2-2.
• LIST Accesses the saved channel list.
• FLASHBK Alternates between the two last channels selected (pressing repeatedly).
• +VOL- Adjusts the volume level.
• FAV Accesses your favorite channel list.
• INFO Shows information on the current program.
• MUTE Mutes all sounds.
• ACH Scrolls through the saved channels.
• PAGE Moves to the previous or next screen.
• SETTINGS Accesses the main menu.
• SMART Accesses the Home menu.
• MY APPS Shows the list of Apps.
• Navigation buttons Scrolls through menus or options. (up/down/left/right)
• OK Selects menus or options and confirms your input.
• BACK Returns to the previous screen.
• Q.MENU Accesses the quick menu.
• EXIT Clears all on-screen displays and returns to TV viewing.
• Color buttons (Red, Green, Yellow, Blue) These access special functions in some menus.
• Control buttons (1 II,,) Controls the SIMPLINK compatible devices (USB, SIMPLINK).
• SIMPLINK Accesses the AV devices connected to the TV; Opens the SIMPLINK menu.
• SLEEP Sets the length of time until the TV to turns off.
• SAP/* Enables VD function. SAP (Secondary Audio Program) Feature can also be enabled by pressing the key.
• TV Returns to the last TV channel.

Check the remote control sensor on the product and try again.

Check if there is any obstacle between the product and the remote control.

Check if the batteries are still working and properly installed (+ to +, – to -).

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

Check the power control settings. The power supply may be interrupted.

Check if the Sleep Timer/Off Time is activated in the TIME settings.

If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.