LG 32LB6200-ZE (01) PDF Document

To attach the stand to your LG 32LB6200-ZE, please follow these steps which vary slightly depending on your specific model series:

For models LB55**, LB56**-ZE / ZC, LB62**-ZA / ZB:

1. Place the screen facing down on a cushioned table or flat surface to protect it from scratches.

2. Attach the A Stand Base to the B Stand Base.

3. Align the stand assembly with the mounting holes on the bottom of the TV.

4. Insert and tighten the provided screws. For 32-inch models in this series, use four M4 x L20 screws. For other sizes, use four M4 x L14 screws.

For models LB56**-ZT / ZQ, LB62**-ZE:

1. Place the screen facing down on a cushioned table or flat surface.

2. Attach the A Stand Base to the B Stand Base.

3. Align the stand assembly with the mounting slots on the TV.

4. Insert and tighten the provided screws. For 32-inch models in this series, use four M4 x L20 screws. For other sizes, use four M4 x L14 screws.

Always place the screen facing down on a cushioned surface during assembly to prevent scratches.

Connect your LG 32LB6200-ZE to a wall antenna socket using an RF cable (75 Ω). The connection port is labeled ANTENNA/CABLE IN on the back of the TV.

Important Notes:

– Use a signal splitter if you need to connect more than 2 TVs.

– If the image quality is poor, consider installing a signal amplifier.

– If the image quality is poor with an antenna connected, try realigning the antenna in the correct direction.

– An antenna cable and converter are not supplied with the TV.

– The supported DTV audio formats are MPEG, Dolby Digital, Dolby Digital Plus, and HE-AAC.

If your LG 32LB6200-ZE is a satellite model, you can connect it to a satellite dish. Use a satellite RF cable (75 Ω) to connect the LNB Satellite IN port on the back of the TV to the satellite socket.

The Euro Scart connection transmits video and audio signals from an external device to your LG 32LB6200-ZE. Connect the external device and the TV using a Euro Scart cable.

Important Notes:

– Any Euro Scart cable used must be signal shielded.

– For 3D models, when watching digital TV in 3D imaging mode, only 2D signals can be output through the SCART cable.

The AV1 (TV Out) port functions based on the current input mode, as shown in the table below:

You can connect various external devices such as HD receivers, DVD players, VCRs, audio systems, USB storage devices, PCs, and gaming devices to your LG 32LB6200-ZE. After connecting, switch the input mode on the TV to select the device.

General Guidelines:

– The external device connection may differ from the model diagrams.

– Connect external devices to the TV regardless of the order of the TV ports.

– If you record a TV programme on a DVD recorder or VCR, ensure the TV signal input cable is connected to the TV through the recorder.

– When connecting a gaming device, use the cable supplied with it.

PC Mode Notes:

– In PC mode, noise may be associated with resolution, vertical pattern, contrast, or brightness. If noise is present, try changing the PC output to another resolution, changing the refresh rate, or adjusting the brightness and contrast in the TV’s PICTURE menu until the picture is clear.

– In PC mode, some resolution settings may not work properly depending on the graphics card.

The Joystick button, located below the TV screen, allows you to operate basic TV functions by pressing or moving it up, down, left, or right.

Basic Functions:

– Power On: When the TV is off, place your finger on the joystick button and press it once and release it.

– Power Off: When the TV is on, press and hold the joystick button for a few seconds and release it. (If the Menu is on the screen, this action will exit the Menu.)

– Volume Control: Move the joystick button left or right to adjust the volume.

– Programmes Control: Move the joystick button up or down to scroll through the saved programmes.

Adjusting the Menu:

When the TV is on, press the joystick button once to open the menu. You can then adjust menu items by moving the joystick up, down, left, or right.

– TV off: Turns the power off.

– Settings: Accesses the main menu.

– Close: Clears on-screen displays and returns to TV viewing.

– Input List: Changes the input source.

Note: When moving the joystick, be careful not to press it first, as that will prevent you from adjusting the volume or changing programmes.

To prevent your LG 32LB6200-ZE from being scratched or damaged and to ensure safe transportation, please follow this advice:

– Avoid touching the screen at all times, as this may result in damage.

– It is recommended to move the TV in the box or packing material that it originally came in.

– Before moving or lifting the TV, disconnect the power cord and all cables.

– When holding the TV, the screen should face away from you to avoid damage.

– Hold the top and bottom of the TV frame firmly. Do not hold the transparent part, speaker, or speaker grill area.

– When transporting a large TV, there should be at least 2 people.

– When transporting the TV, do not expose it to jolts or excessive vibration.

– Keep the TV upright during transport; never turn it on its side or tilt it.

– Do not apply excessive pressure to the frame chassis as it may damage the screen.

Mounting on a table:

1. Lift and tilt the TV into its upright position on a table.

2. Leave a 10 cm (minimum) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Caution: Do not place the TV near or on sources of heat, as this may result in fire or other damage.

Securing the TV to a wall (This feature is not available for all models):

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are already bolts in the eye-bolt position, remove them first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Caution: Make sure that children do not climb on or hang on the TV.

Note: Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts and ropes are not provided.

To mount your LG 32LB6200-ZE on a wall, attach an optional wall mount bracket to the rear of the TV and install it on a solid wall perpendicular to the floor. LG recommends that wall mounting be performed by a qualified professional installer.

Important Cautions:

– Disconnect the power first before moving or installing the TV.

– Use an authorized LG wall mount. If you install the TV on a ceiling or slanted wall, it may fall and cause severe injury.

– Do not over-tighten the screws, as this may cause damage and void your warranty.

– Use screws and wall mounts that meet the VESA standard. Damages or injuries from misuse are not covered by the warranty.

Wall Mounting Bracket Specifications (Separate Purchase):

The remote control for the LG 32LB6200-ZE (LB62** model) has the following functions:

To automatically tune the programmes on your LG 32LB6200-ZE, navigate to SETTINGS → SETUP → Auto Tuning. This function will automatically find and store available programmes.

– If the Input Source is not connected properly, programme registration may not work.

– Auto Tuning only finds programmes that are currently broadcasting.

– If the Lock System is turned on, a pop-up window will appear asking for a password.

You can adjust the picture settings on your LG 32LB6200-ZE through the SETTINGS → PICTURE menu. Here are the available options:

Picture Wizard III: Calibrates and adjusts for optimum picture quality using the remote control without expensive pattern devices.

Picture Mode: Select a pre-optimized picture mode.

– Vivid: Heightens contrast, brightness and sharpness.

– Standard: Displays images in standard levels of contrast, brightness and sharpness.

– Eco/APS: Reduces power consumption by changing TV settings.

– Cinema/Game: Displays the optimum picture for movies or games.

– Sports: Optimizes the image for high and dynamic actions.

– Expert 1, 2: Menu for advanced picture quality adjustment, intended for ISF-certified tuning professionals.

Advanced Control / Expert Control: Calibrates the screen for each picture mode.

– Dynamic Contrast: Adjusts contrast based on image brightness.

– Dynamic Colour: Adjusts colours to appear more natural.

– Skin Colour, Sky Colour, Grass Colour: Sets these colour spectrums separately.

– Gamma: Sets the gradation curve.

– Colour Gamut: Selects the range of colours that can be expressed.

– Edge Enhancer: Shows clearer and more distinctive edges.

– Colour Filter: Fine-tunes colour saturation and hue.

– Colour Temperature: Adjusts the overall tone of the screen.

– Colour Management System: An expert system to adjust six colour areas (Red / Green / Blue / Cyan / Magenta / Yellow) independently.

You can manage the audio output on your LG 32LB6200-ZE through the SETTINGS → AUDIO menu.

– To use TV speaker: Go to Sound Out → TV Speaker. Sound is output through the TV’s internal speakers.

– To use External Speaker (Optical): Go to Sound Out → External Speaker (Optical). Sound is output through a speaker connected to the optical port. SimpLink is supported.

– To connect and use LG audio device: Go to Sound Out → LG Sound Sync (Optical). Connect an LG audio device to the optical digital audio output port for rich, powerful sound.

– To use Headphones: Go to Sound Out → Headphone. Sound is output through the headphone port.

– To synchronize audio and video: Go to AV Sync. Adjust. If video and audio do not match, set this to ON to adjust the sound output (TV speakers or SPDIF) to the screen image.

– To use Digital Sound Out: Go to Sound Out → External Speaker (Optical) → Digital Sound Out to set up the digital sound output format based on the audio input.

SIMPLINK is a feature that enables you to control and manage various multimedia devices conveniently via the TV’s remote control and SIMPLINK menu. This function is only compatible with devices that have the SIMPLINK logo.

Setup:

1. Connect the TV’s HDMI IN terminal to the SIMPLINK device’s HDMI output terminal using a high-speed HDMI® cable (with CEC feature).

2. Select INPUT(OPTION) → SIMPLINK.

3. In the SIMPLINK Setting window, set the SIMPLINK function to ON.

4. In the SIMPLINK menu window, select the device you want to control.

SIMPLINK Functions:

– Direct Play: Plays the multimedia device on the TV instantly.

– Select multimedia device: Selects the desired device via the SIMPLINK menu to control it from the TV screen.

– Disc playback: Manages the multimedia device with the TV remote control.

– Power off all devices: When you power off the TV, all connected devices are turned off.

– Sync Power on: When the equipment with SIMPLINK starts to play, the TV will automatically turn on.

– Speaker: Select speaker either on the home theatre unit or the TV.

To set password:

Navigate to SETTINGS → LOCK → Set Password. This allows you to set or change the TV password. The initial password is set to ‘0000’.

To return to Factory Reset:

Navigate to SETTINGS → OPTION → Factory Reset. All stored information is deleted and TV settings are reset. The TV will turn itself off and back on to complete the process. Do not turn off the power during initialization. If the Lock System is in place, a pop-up window will ask for the password.

To remove a USB device:

Go to Q.MENU → USB Device and select the USB storage device you want to remove. When you see a message that the USB device has been removed, you can safely separate it from the TV.

Warnings for using a USB storage device:

– Use only USB storage devices formatted with the Windows FAT32 or NTFS File System.

– It is recommended to use USB memory sticks of 32 GB or less and USB HDDs of 1 TB or less.

– For external USB HDDs, use devices with a rated voltage of less than 5 V and a rated current of less than 500 mA.

– If a USB HDD with a power-saving function does not work properly, turn the power off and on.

– Data in the USB storage device can be damaged, so be sure to back up important files.

Supported File Formats:

Your TV supports various video, audio, photo, and subtitle formats from a USB device. The maximum data transfer rate is 20 Mbps.

– External Subtitle Formats: *.srt, *.smi, *.sub, *.ass/*.ssa, *.txt, *.psb

– Internal Subtitle Formats: XSUB (from DivX6)

– Video Formats: Maximum resolution is 1920 x 1080 @ 30p. Supported containers include .asf, .wmv, .divx, .avi, .ts, .trp, .tp, .mts, .m2ts, .vob, .mp4, .m4v, .mov, .mkv, motion JPEG, .mpg, .mpeg, .mpe, .dat, .flv, .rm, .rmvb, .3gp, .3gp2.

– Audio Formats: mp3, AAC, M4A, WMA, OGG.

– Photo Formats: 2D (jpeg, jpg, jpe), BMP, PNG.

When viewing 3D content on your LG 32LB6200-ZE, please follow these guidelines for a safe and comfortable experience.

Viewing Environment and Time:

– Take 5-15 minute breaks every hour when watching 3D content.

– Maintain a distance of at least twice the screen diagonal length.

Health Precautions:

– Some users may experience a seizure when exposed to flashing lights. Do not watch 3D videos if you feel nausea, are pregnant, or have a chronic illness such as epilepsy or a cardiac disorder.

– If you have strabismus (cross-eyed), amblyopia (weak eyesight), or astigmatism, you may have trouble sensing depth and feel fatigue easily. Take more frequent breaks.

– Discontinue watching if you experience headache, eyeball pain, dizziness, nausea, palpitation, or blurriness.

Viewing Age:

– Viewing 3D content is prohibited for children under the age of 6.

– Special monitoring is required for children under 10.

– Teenagers under 19 may react with sensitivity and should refrain from watching for long periods when tired.

Cautions for 3D Glasses:

– Make sure to use LG 3D glasses.

– Do not use 3D glasses instead of your normal glasses, sunglasses, or protective goggles.

– The 3D glasses are fragile and easily scratched. Always use a soft, clean cloth when wiping the lenses. Do not scratch them with sharp objects or clean them with chemicals.

To keep your LG 32LB6200-ZE in the best condition, clean it regularly.

General Cleaning:

– Make sure to turn the power off and disconnect the power cord and all other cables first.

– When the TV is left unattended for a long time, disconnect the power cord from the wall outlet.

Screen, frame, cabinet, and stand:

– To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.

– To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent, then wipe immediately with a dry cloth.

– Avoid touching the screen at all times, as this may result in damage.

– Do not push, rub, or hit the screen surface with your fingernail or a sharp object.

– Do not use any chemicals (glass cleaner, abrasives, wax, benzene, alcohol, etc.) as this may damage the product.

– Do not spray liquid directly onto the surface.

Power cord:

– Remove accumulated dust or dirt from the power cord regularly.

If you cannot control the TV with the remote control, try the following solutions:

– Check the remote control sensor on the product and try again.

– Check if there is any obstacle between the product and the remote control.

– Check if the batteries are still working and are properly installed (positive to positive, negative to negative).

If there is no image or sound, follow these steps:

– Check if the product is turned on.

– Check if the power cord is connected to a wall outlet.

– Check if there is a problem with the wall outlet by connecting other products to it.

If your TV turns off suddenly, check the following:

– Check the power control settings. The power supply may have been interrupted.

– Check if the Automatic Standby, Sleep Timer, or Off Time feature is activated in the TIME settings.

– If there is no signal while the TV is on, it will turn off automatically after 15 minutes of inactivity.

If you see a ‘No signal’ or ‘Invalid Format’ message when your PC is connected via HDMI, try these steps:

– Turn the TV off and on again using the remote control.

– Reconnect the HDMI cable.

– Restart the PC with the TV already turned on.