LG 32LB561U-ZC (01) PDF Document

To attach the stand to your LG 32LB561U-ZC TV, please follow these steps. Note that the image shown in the manual may differ from your TV model.

1. Place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

2. Assemble the stand parts. For models like LB55**, LB56**-ZE / ZC, LB62**-ZA / ZB, attach the ‘A Stand Base’ to the ‘B Stand Base’.

3. Align the assembled stand with the mounting holes on the bottom of the TV set.

4. Insert and tighten the provided screws to secure the stand to the TV. For the 32-inch model (32LB56**-ZE / ZC), use the four M4 x L20 screws provided.

To connect your LG 32LB561U-ZC TV to a wall antenna socket, use an RF cable (75 Ω). The antenna cable and converter are not supplied.

Important notes:

• If you plan to use more than two TVs, use a signal splitter.

• If the image quality is poor, install a signal amplifier correctly to improve it.

• If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.

• The supported DTV Audio formats are MPEG, Dolby Digital, Dolby Digital Plus, and HE-AAC.

To connect a satellite dish to your LG 32LB561U-ZC (satellite models only), use a satellite RF cable (75 Ω) to connect the TV’s “LNB Satellite IN” socket to the satellite dish. The RF cable is not provided.

The Euro Scart connection on your LG 32LB561U-ZC transmits video and audio signals from an external device. Connect the external device to the TV set using a Euro Scart cable. Ensure any Euro Scart cable used is signal shielded. The TV Out function (AV1) outputs Analogue TV or Digital TV signals based on the input mode.

The following table shows the output type based on the current input mode:

You can connect various external devices to your LG 32LB561U-ZC TV. Available external devices include:

• HD receivers

• DVD players

• VCRs

• Audio systems

• USB storage devices

• PC

• Gaming devices

• Other external devices

For the best picture and audio quality, it is recommended to connect external devices using an HDMI cable. Refer to the manual provided with each device for specific connection information.

Please note:

• External device connections may differ from the model shown.

• Connect external devices to the TV regardless of the order of the TV port.

• In PC mode, noise may be associated with resolution, vertical pattern, contrast, or brightness. If noise is present, change the PC output to another resolution, change the refresh rate, or adjust the brightness and contrast on the PICTURE menu until the picture is clear.

You can operate the TV functions by pressing or moving the joystick button located below the TV screen. When moving your finger over the button, be careful not to press it first, as this will prevent you from adjusting the volume or changing programmes.

When the TV is turned on, press the joystick button once. You can then adjust the menu items by moving the joystick up, down, left, or right.

To prevent your LG 32LB561U-ZC from being scratched or damaged and to ensure safe transportation, please follow this advice:

• Avoid touching the screen at all times, as this may cause damage.

• It is recommended to move the TV in the box or packing material that it originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Do not hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, at least two people are required.

• When transporting the TV, do not expose it to jolts or excessive vibration.

• Keep the TV upright; never turn it on its side or tilt it left or right.

• Do not apply excessive pressure that could cause flexing or bending of the frame chassis, as it may damage the screen.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a minimum of 10 cm (4 inches) of space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

CAUTION: Do not place the TV near or on sources of heat, as this may result in fire or other damage.

To secure your LG 32LB561U-ZC to a wall (a feature not available on all models):

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are already bolts in the eye-bolt position, remove them first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

• Use a platform or cabinet that is strong and large enough to support the TV securely.

• Brackets, bolts, and ropes are not provided. You can obtain additional accessories from your local dealer.

• CAUTION: Make sure that children do not climb on or hang on the TV.

To mount your LG 32LB561U-ZC, attach an optional wall mount bracket to the rear of the TV and install it on a solid wall perpendicular to the floor. LG recommends that wall mounting be performed by a qualified professional installer.

Important Cautions:

• Disconnect the power first before moving or installing the TV.

• Use an authorized LG wall mount. If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury.

• Do not over-tighten the screws, as this may cause damage and void your warranty.

• Use screws and wall mounts that meet the VESA standard. Any damages or injuries from misuse are not covered by the warranty.

Wall Mounting Bracket Specifications (Separate Purchase):

The remote control for your LG 32LB561U-ZC (models LB55**, LB56**) has the following functions. Make sure to point the remote control toward the remote control sensor on the TV.

To automatically tune the programmes on your LG 32LB561U-ZC, go to SETTINGS → SETUP → Auto Tuning. This function automatically finds and stores available programmes.

• If the Input Source is not connected properly, programme registration may not work.

• Auto Tuning only finds programmes that are currently broadcasting.

• If the Lock System is turned on, a pop-up window will appear asking for a password.

To calibrate and adjust for optimum picture quality on your LG 32LB561U-ZC, navigate to SETTINGS → PICTURE → Picture Wizard III. This feature allows you to adjust the picture quality using the remote control without needing expensive pattern devices or specialist help.

To select the picture mode optimized for your viewing environment or programme, go to SETTINGS → PICTURE → Picture Mode. The available modes are:

• Vivid: Heightens contrast, brightness, and sharpness to display vivid images.

• Standard: Displays images in standard levels of contrast, brightness, and sharpness.

• Eco/APS: The Energy Saver feature changes settings on the TV to reduce power consumption (depending on model).

• Cinema/Game: Displays the optimum picture for movies or games.

• Sports: Optimizes the video image for high and dynamic actions by emphasizing primary colours such as white, grass, or sky blue.

• Expert 1, 2: A menu for adjusting picture quality that allows experts and amateurs to enjoy the best TV viewing. This is the adjustment menu provided for ISF-certified picture tuning professionals.

The available range of picture modes may differ depending on the input signal.

To safely remove a USB storage device, go to Q.MENU → USB Device. Select the USB storage device that you want to remove. When you see a message that the USB device has been removed, you can separate the device from the TV. Once a USB device has been selected for removal, it can no longer be read. Remove the USB storage device and then re-connect it if you wish to use it again.

Yes, please consider the following when using a USB storage device with your LG 32LB561U-ZC:

• If the USB device has a built-in auto recognition program or uses its own driver, it may not work.

• Some USB storage devices may not work or may work incorrectly.

• Use only USB storage devices formatted with the Windows FAT32 or NTFS File System.

• For external USB HDDs, it is recommended to use devices with a rated voltage of less than 5 V and a rated current of less than 500 mA.

• It is recommended to use USB memory sticks of 32 GB or less and USB HDDs of 1 TB or less.

• If a USB HDD with a power-saving function does not work properly, turn the power off and on. For more information, refer to the user manual of the USB HDD.

• Data in the USB storage device can be damaged, so be sure to back up important files to other devices. Data maintenance is the user’s responsibility.

Clean your TV regularly to keep it in the best condition and extend its lifespan. First, make sure to turn the power off and disconnect all cables.

Screen, frame, cabinet, and stand:

• To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.

• To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth.

• Avoid touching the screen at all times, as this may result in damage.

• Do not push, rub, or hit the screen surface with your fingernail or a sharp object.

• Do not use any chemicals as this may damage the product.

• Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.

Power cord:

• Remove the accumulated dust or dirt on the power cord regularly.

If you cannot control the TV with the remote control, try the following solutions:

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote control.

• Check if the batteries are still working and properly installed (positive to positive, negative to negative).

If there is no image and no sound, please check the following:

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

If your TV turns off suddenly, consider these possibilities:

• Check the power control settings. The power supply may be interrupted.

• Check if the Automatic Standby (depending on model), Sleep Timer, or Off Time feature is activated in the TIME settings.

• If there is no signal while the TV is on, it will turn off automatically after 15 minutes of inactivity.

If you see a ‘No signal’ or ‘Invalid Format’ message when your PC is connected via HDMI, try these steps:

• Turn the TV off and on using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.