LG 32LB550U-ZA (01) PDF Document

To attach the stand to your LG 32LB550U-ZA, please follow these instructions. Note that the image shown in the manual may differ from your TV model.

1. Place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

2. Assemble the stand parts. For models LB55**, LB56**-ZE / ZC, and LB62**-ZA / ZB, attach the ‘A Stand Base’ to the ‘B Stand Base’. For models LB56**-ZT / ZQ and LB62**-ZE, attach the ‘A Stand Base’ to the ‘B Stand Base’.

3. Attach the assembled stand to the TV set using the provided screws. You will need 4 screws (4EA).

For models 32LB55**, 32LB56**-ZE / ZC, 32LB62**-ZA / ZB, use M4 x L20 screws.

For models 32LB56**-ZT / ZQ, 32LB62**-ZE, use M4 x L20 screws.

For all other models in these series, use M4 x L14 screws.

Connect the TV to a wall antenna socket using an RF cable (75 Ω) into the “ANTENNA / CABLE IN” port on the back of the TV.

Notes:

Use a signal splitter if you need to connect more than 2 TVs.

If the image quality is poor, install a signal amplifier to improve it.

If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.

An antenna cable and converter are not supplied.

Supported DTV Audio formats are MPEG, Dolby Digital, Dolby Digital Plus, and HE-AAC.

For satellite models only, connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω). The port is labeled “LNB Satellite IN”.

The Euro Scart connection transmits video and audio signals from an external device to your LG 32LB550U-ZA. Connect the external device and the TV with a Euro Scart cable. Any Euro Scart cable used must be signal shielded.

The type of signal output through the AV1 (TV Out) port depends on the current input mode:

When connecting a PC to your LG 32LB550U-ZA, please be aware of the following:

In PC mode, there may be noise associated with the resolution, vertical pattern, contrast, or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate, or adjust the brightness and contrast on the PICTURE menu until the picture is clear.

In PC mode, some resolution settings may not work properly depending on the graphics card.

You can operate the TV functions by pressing or moving the joystick button located below the TV screen up, down, left, or right.

Basic Functions:

Power On: When the TV is off, place your finger on the joystick button and press it once and release it.

Power Off: When the TV is on, place your finger on the joystick button and press it once for a few seconds and release it. (If the Menu is on the screen, pressing and holding the joystick will exit the Menu.)

Volume Control: Place your finger over the joystick button and move it left or right to adjust the volume.

Programmes Control: Place your finger over the joystick button and move it up or down to scroll through the saved programmes.

Note: When you move the joystick button up, down, left, or right, be careful not to press it. If you press the joystick button first, you cannot adjust the volume level and saved programmes.

Adjusting the Menu:

When the TV is turned on, press the joystick button one time. You can adjust the Menu items by moving the joystick button up, down, left, or right.

TV off: Turns the power off.

Settings: Accesses the main menu.

Close: Clears on-screen displays and returns to TV viewing.

Input List: Changes the input source.

To prevent your LG 32LB550U-ZA from being scratched or damaged and for safe transportation, please follow this advice:

Avoid touching the screen at all times, as this may result in damage.

It is recommended to move the TV in the box or packing material that it originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Do not hold the transparent part, speaker, or speaker grill area.

When transporting a large TV, there should be at least 2 people.

When transporting the TV, do not expose it to jolts or excessive vibration.

Keep the TV upright when transporting it; never turn it on its side or tilt it to the left or right.

Do not apply excessive pressure to cause flexing/bending of the frame chassis as it may damage the screen.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a 10 cm (minimum) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Caution: Do not place the TV near or on sources of heat, as this may result in fire or other damage.

This feature is not available for all models. To secure your TV to a wall:

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are already bolts in the eye-bolt position, remove them first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Caution: Ensure that children do not climb on or hang on the TV.

Note:

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts, and ropes are not provided. You can obtain additional accessories from your local dealer.

To mount your LG 32LB550U-ZA on a wall, attach an optional wall mount bracket to the rear of the TV and install it on a solid wall perpendicular to the floor. LG recommends that wall mounting be performed by a qualified professional installer. Use screws and a wall mount bracket that meet the VESA standard.

Cautions:

Disconnect the power first before moving or installing the TV.

If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount.

Do not over-tighten the screws as this may cause damage and void your warranty.

Use screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

The length of screws may differ depending on the wall mount. Make sure to use the proper length.

Wall Mounting Bracket Specifications (Separate Purchase):

The functions for the remote control buttons are as follows (may vary slightly by model):

To automatically tune the programmes, navigate to SETTINGS > SETUP > Auto Tuning. This function will automatically find and store available programmes.

Please note:

If the Input Source is not connected properly, programme registration may not work.

Auto Tuning only finds programmes that are currently broadcasting.

If the Lock System is turned on, a pop-up window will appear asking for a password.

To select a picture mode optimized for your viewing environment, go to SETTINGS > PICTURE > Picture Mode. Available options are:

Vivid: Heightens contrast, brightness, and sharpness to display vivid images.

Standard: Displays images in standard levels of contrast, brightness, and sharpness.

Eco/APS: (Depending on model) The Energy Saver feature changes settings on the TV to reduce power consumption.

Cinema/Game: Displays the optimum picture for movies or games.

Sports: Optimizes the video image for high and dynamic actions by emphasizing primary colours such as white, grass, or sky blue.

Expert 1, 2: A menu for adjusting picture quality that allows experts and amateurs to enjoy the best TV viewing. This is the adjustment menu provided for ISF-certified picture tuning professionals.

SIMPLINK allows you to control and manage various multimedia devices with your TV remote via the SIMPLINK menu. This feature is only compatible with devices bearing the SIMPLINK logo.

Setup:

1. Connect the TV’s HDMI IN terminal to the SIMPLINK device’s HDMI output terminal using a high-speed HDMI® cable (with CEC feature added).

2. Select INPUT(OPTION) > SIMPLINK. The SIMPLINK menu window will appear.

3. In the SIMPLINK Setting window, set the SIMPLINK function to ON.

4. In the SIMPLINK menu window, select the device you want to control.

SIMPLINK Function Descriptions:

Direct Play: Plays the multimedia device on the TV instantly.

Select multimedia device: Selects the desired device via the SIMPLINK menu to control it from the TV screen instantly.

Disc playback: Manages the multimedia device with the TV remote control.

Power off all devices: When you power off the TV, all connected devices are turned off.

Sync Power on: When the equipment with SIMPLINK function connected to the HDMI terminal starts to play, the TV will automatically turn on.

Speaker: (Depending on model) Select speaker either on the home theatre unit or the TV.

To return your TV to its factory settings, go to SETTINGS > OPTION > Factory Reset. All stored information will be deleted, and the TV settings will be reset. The TV will turn itself off and back on to complete the process.

Note:

If the Lock System is in place, a pop-up window will appear and ask for the password.

Do not turn off the power during initialization.

When using a USB storage device, please follow these warnings:

If the USB storage device has a built-in auto recognition program or uses its own driver, it may not work.

Some USB storage devices may not work or may work incorrectly.

Use only USB storage devices formatted with the Windows FAT32 or NTFS File System.

For external USB HDDs, it is recommended that you use devices with a rated voltage of less than 5 V and a rated current of less than 500 mA.

It is recommended that you use USB memory sticks of 32 GB or less and USB HDDs of 1 TB or less.

If a USB HDD with a power-saving function does not work properly, turn the power off and on.

Data in the USB storage device can be damaged, so be sure to back up important files to other devices. Data maintenance is the user’s responsibility and the manufacturer is not responsible for data loss.

Clean your TV regularly to keep the best performance and to extend its lifespan.

First steps:

Make sure to turn the power off and disconnect the power cord and all other cables first.

When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges.

Screen, frame, cabinet and stand:

To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.

To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth.

Caution:

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in scratches and image distortions.

Do not use any chemicals as this may damage the product.

Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or malfunction.

Power cord:

Remove the accumulated dust or dirt on the power cord regularly.

Check the remote control sensor on the product and try again.

Check if there is any obstacle between the product and the remote control.

Check if the batteries are still working and properly installed (positive to positive, negative to negative).

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

Check the power control settings. The power supply may be interrupted.

Check if the Automatic Standby / Sleep Timer / Off Time feature is activated in the TIME settings.

If there is no signal while the TV is on, it will turn off automatically after 15 minutes of inactivity.

Turn the TV off/on using the remote control.

Reconnect the HDMI cable.

Restart the PC with the TV on.