LENSGO 40SHC (01) PDF Document

You will receive the following accessories with your LENSGO 40SHC, subject to the options available at the time of your order:

1. Handheld light

2. Silicone softbox

3. Mobile phone clip (horizontal / vertical)

4. Battery charger

5. Camera bracket (mobile phone holder can be mounted)

6. Hand screw X2

To turn the LENSGO 40SHC on or off, long press the On / Off button.

To adjust the brightness of the LENSGO 40SHC, turn the knob. Turn it clockwise to increase the brightness from 0-100%. The indicator light will change in accordance with the percentage ratio of light. Turn the knob counterclockwise to dim the brightness.

To switch between warm and cold light, click the power button once for an instant switch.

You can charge the LENSGO 40SHC using either the TYPE-C charging port or the DC charging port. The required charging voltage is 5V 2A. It takes approximately 2 hours to achieve a full charge.

When the LENSGO 40SHC is in the off state, click the power button once. The indicator lights will display the current power percentage. If none of the lights turn on, please charge the device.

The indicator lights on the LENSGO 40SHC have several functions:

During Operation: When the device is switched on, the indicator lights are blue.

Low Battery: If the red light is flashing, the battery is low and the device needs to be charged.

While Charging: The lights will flash in order of the charging percentage (%).

Fully Charged: When the battery is full, the blue lights will stay on continuously.

To use the special lighting effects on the LENSGO 40SHC, follow these steps:

1. Double-click the power button to enter FX mode.

2. Once in FX mode, press the power button to switch between the 8 different effects.

3. After selecting your desired effect, double-click the power button to exit FX mode.

The LENSGO 40SHC features 8 different lighting effect modes:

1. LIGHTNING MODE

2. TV MODE

3. BAD BULB MODE

4. SOS MODE

5. BURST MODE

6. CANDLELIGHT MODE

7. PULSE FLASH MODE

8. HIGH AND LOW BEAM BULBS

1. Align the camera bracket to the bottom of the LENSGO 40SHC light and tighten the screw by hand.

2. For a camera: Set the camera up on the bracket and screw it in by hand using the hand screws.

3. For a mobile phone: Attach the mobile phone clip to the bracket and secure it by hand, then place your phone in the clip.

4. The bracket also features 1/4 screw holes to expand your setup and install any equipment with a 1/4 interface according to your needs.

Before every use, please carefully check whether the installation is stable to prevent accidents.

CREATIVE SCENE LIGHTING EFFECTS: Create different personalized atmospheres to enhance the quality of the image shot.

WITH SILICONE SOFTBOX: The soft light amplitude is suitable, making the light soft and not harsh.

0%-100% BRIGHTNESS ADJUSTABLE: By turning the adjustment knob, the brightness change range is 0-100%.

The LENSGO 40SHC is a COB 40W light with a dual colour temperature of 2700-7000K, a colour rendering index ≥96, and burst flash capabilities.

To clean the LENSGO 40SHC, please use a soft sponge, soft cloth, or dry cloth. Do not use bleach or a wire ball. Wipe the product clean and keep it dry. For storage, keep it in a cool, dry place and prohibit exposure to the sun or water.

Please observe the following safety precautions when using your LENSGO 40SHC:

• Keep this product out of the reach of children in a safe place.

• Do not touch the COB lamp beads with your hands to prevent burning hands.

• This product is a precision instrument; please avoid dropping it when using it.

• Before each use, please be sure to check whether the installation is stable to prevent accidents during use.

• It is recommended to use the original LENSGO cables and parts.

• Do not cover the ventilation holes when using the silicone softbox.

• Please switch off the product after charging. To protect the safety and life of the battery, try not to use it during charging.

• Store in a cool, dry place; prohibit exposure to the sun and water.

• For any required repairs, contact authorised service personnel.