LENOVO V14 G4 ABP 1 (01) PDF DOCUMENT

The front of your LENOVO V14 G4 ABP 1 includes the following components:

The base of your LENOVO V14 G4 ABP 1 includes the following components:

The left side of your LENOVO V14 G4 ABP 1 features the following ports and connectors:

The right side of your LENOVO V14 G4 ABP 1 features the following ports and connectors:

The bottom of your LENOVO V14 G4 ABP 1 includes the following components:

*for selected models

Depending on many factors such as the processing capability of the host and peripheral devices, file attributes, and other factors related to system configuration and operating environments, the actual transfer rate using the various USB connectors on this device will vary and will be slower than the data rate listed below.

Maximum altitude (without pressurization)

3048 m (10 000 ft)

Temperature

• At altitudes up to 2438 m (8000 ft)

– Operating: 5°C to 35°C (41°F to 95°F)

– Storage: 5°C to 43°C (41°F to 109°F)

• At altitudes above 2438 m (8000 ft)

– Maximum temperature when operating under the unpressurized condition: 31.3°C (88°F)

Note: When you charge the battery, its temperature must be no lower than 10°C (50°F).

Relative humidity

• Operating: 8% to 95% at wet-bulb temperature 23°C (73°F)

• Storage: 5% to 95% at wet-bulb temperature 27°C (81°F)

CAUTION:

When the computer is operating, it should be placed on a hard and flat surface with its bottom area not in contact with user’s bare skin. Under normal operating conditions, the temperature of the bottom surface will remain within an acceptable range as defined in IEC 62368-1, but such temperatures can still be high enough to cause discomfort or harm to the user if directly touched for over one minute at a time. As such, it is recommended that users avoid prolonged direct contact with the bottom of the computer.

To configure settings, type the corresponding keywords in the Windows search box and select the best match. Follow the on-screen instructions to customize settings.

The Novo Button menu can be displayed before the operating system starts. From the menu, you can choose to:

• Open the BIOS/UEFI setup utility

• Open the boot device selection menu

• Open the Windows startup options screen

To open the Novo Button menu:

Step 1. Turn off the computer.

Step 2. Open the LCD screen and press the Novo button (located in the Novo button hole on the right side).

Alternatively, turn off the computer. Press Fn and the hotkey with a curved arrow icon to open the Novo Button menu.

Hotkeys are keys with printed icons, usually on the top row of the keyboard, providing shortcuts to functions. They share keys with function keys (F1-F12). The FnLock switch (Fn + Esc) determines how you use them.

The primary function is denoted by the icon or character printed on top, and the secondary function is below it.

Note: The FnLock switch does not apply to hotkeys not found in the first row of the keyboard. To use these hotkeys, always hold down the Fn key while pressing the key.

Your LENOVO V14 G4 ABP 1 includes a dedicated numeric keypad on the far right of the keyboard for entering numbers and operators quickly.

Press the NumLock key to enable or disable the numeric keypad.

Your computer may be pre-installed with Lenovo Vantage, Lenovo PC Manager, or Lenovo Smart Engine. Most features described here can be enabled or disabled in one of these apps.

• Eye Care Mode: Intelligently adjusts the color temperature of the screen and can reduce the chances of developing eye fatigue or eye strain.

• Smart Noise Cancelling: By filtering the input and output environments, Smart Noise Cancelling helps you reduce noise and optimize the call effect in different scenarios.

You can switch the battery’s active charging mode in Lenovo Vantage, Lenovo PC Manager, or Lenovo Smart Engine. The recommended temperature range for charging is between 10°C (50°F) and 35°C (95°F).

• Normal mode: The most basic charging mode. It typically takes 2 to 4 hours for the battery to charge from 0% to 100%.

• Rapid charge mode: If you want the battery to be charged faster than in normal mode, switch to rapid charge mode.

• Conservation mode: If your computer is constantly plugged into an electrical outlet, consider this mode. The battery’s charge will be kept within 75%-80%, which is beneficial to the long-term health of the battery.

If your computer is constantly plugged in and the battery rarely discharges, the battery may not be charged to its full capacity even if the battery meter reports 100% charge. You can recover the battery’s full charging potential simply by discharging and re-charging the battery.

Step 1. Unplug the computer and use it until the battery charge drops below 20%.

Step 2. Plug in the computer and charge the battery to 100%.

By default, pressing the power button puts the computer to sleep mode. You can change this behavior in the Windows Control Panel.

Step 1. Type Control Panel in the Windows search box and then press Enter. Open the control panel and view by large or small icons.

Step 2. Select power options and then click choose what the power button does.

This operation is applicable to computers with pre-installed Windows.

Step 1. Type power plan in the Windows search box and then press Enter.

Step 2. Customize a power plan of your preference.

You can switch the operation mode in the pre-installed app Lenovo Vantage, Lenovo Smart Engine, or Lenovo PC Manager. As a shortcut, you can also use the key combination Fn + Q. The following table lists the operation modes and their recommended usage conditions.

Note: In Auto (Balance) mode, the computer dynamically switches between High Performance mode and Power Saving (Quiet) mode depending on the tasks running on the computer.

The displays of some Lenovo computers support dual refresh rates. For such a computer, you can manually switch its display to work at either the higher or lower refresh rate. For Windows operation systems, the manual settings are usually found in Settings → System → Display. As a shortcut, you can also use the key combination Fn + R to switch the display refresh rate.

Note: Not all displays support dual refresh rates. If you cannot find settings to change the display refresh rate, the refresh rate of the display might be fixed or cannot be manually changed.

Step 1. Turn on or restart the computer.

Step 2. Before the Lenovo logo appears on the screen, press F2 repeatedly.

Note: For computers with hotkey mode enabled, press Fn + F2.

To temporarily boot from another device:

Step 1. Turn on or restart the computer.

Step 2. Press F12.

Step 3. From the boot device menu, select a boot device to start the computer.

To make a permanent change on boot devices, enter the UEFI/BIOS setup utility. Select the Boot menu; in the EFI section, select the desired boot device and move it to the top of the device list. Save changes and exit the setup utility for the change to take effect.

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Configuration → Hotkey Mode and press Enter.

Step 3. Change the setting to Disabled or Enabled.

Step 4. Select Exit → Exit Saving Changes.

Notes:

• All passwords set in the setup utility consist of alphanumeric characters only.

• If you start the setup utility using the user password, you can only change a few settings.

Set administrator password:

You set the administrator password to prevent unauthorized access to the UEFI/BIOS setup utility.

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security → Set Administrator Password and press Enter.

Step 3. Enter a password string that contains only letters and numbers and then press Enter.

Step 4. Enter the password again and press Enter.

Step 5. Select Exit → Exit Saving Changes.

Change or remove administrator password:

Only the administrator can change or remove the administrator password.

Step 1. Open the UEFI/BIOS setup utility using the administrator password.

Step 2. Select Security → Set Administrator Password and press Enter.

Step 3. Enter the current password.

Step 4. In the Enter New Password text box, enter the new password.

Step 5. In the Confirm New Password text box, enter the new password again. To remove the password, press Enter in both text boxes without entering any character.

Step 6. Select Exit → Exit Saving Changes.

If you remove the administrator password, the user password is also removed.

You must set the administrator password before you can set the user password.

Step 1. Open the UEFI/BIOS setup utility using the administrator password.

Step 2. Select Security → Set User Password and press Enter.

Step 3. Enter a password string that contains only letters and numbers and then press Enter. The user password must be different from the administrator password.

Step 4. Enter the password again and press Enter.

Step 5. Select Exit → Exit Saving Changes.

If the administrator password has been set, you can enable the power-on password to enforce greater security.

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security → Power on Password and press Enter. The administrator password must be set in advance.

Step 3. Change the setting to Enabled.

Step 4. Select Exit → Exit Saving Changes.

If the power-on password is enabled, a prompt appears on the screen every time you turn on the computer. You must enter the administrator or user password to start the computer.

When Flip to Start is enabled, you can turn on the computer by flipping open the screen. You can set this feature in the UEFI/BIOS setup utility.

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Configuration.

Step 3. Change the setting for Flip to Start.

You may also set Flip to Start in Lenovo Vantage, Lenovo PC Manager or Lenovo Smart Engine.

Set hard disk password:

You can set a hard disk password in the setup utility to prevent unauthorized access to your data.

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security → Set Hard Disk Password and press Enter.

Step 3. Follow on-screen instructions to set both master and user passwords. The master and user hard disk passwords must be set at the same time.

Step 4. Select Exit → Exit Saving Changes.

Change or remove hard disk password:

Step 1. Open the UEFI/BIOS setup utility.

Step 2. Select Security.

Step 3. Change or remove the hard disk password.

• To change or remove the master password, select Change Master Password and press Enter. If you remove the master hard disk password, the user hard disk password is also removed.

• To change the user password, select Change User Password and press Enter. The user hard disk password cannot be removed separately.

Step 4. Select Exit → Exit Saving Changes.

Press and hold the power button until the computer turns off. Then restart the computer.

1. Carefully unplug the ac power adapter and turn off the computer immediately. The more quickly you stop the current from passing through the computer the more likely you will reduce damage from short circuits.

Attention: Although you might lose some data or work by turning off the computer immediately, leaving the computer on might make your computer unusable.

2. Wait until you are certain that all the liquid is dry before turning on your computer.

CAUTION: Do not try to drain out the liquid by turning over the computer. If your computer has keyboard drainage holes on the bottom, the liquid will be drained out through the holes.

Your computer may include an ambient light sensor and the adaptive brightness feature is enabled. The light sensor can detect the intensity of the surrounding light. Using data provided by the sensor, the operating system can dynamically adjust the screen brightness.

The adaptive brightness feature of the operating system can be disabled. For Windows operating systems, adaptive brightness settings are usually found in Settings → System → Display.

Your computer may have Flip to Start enabled. Many Lenovo notebook computers include a sensor that can detect the angle at which the lid is opened. When you open the lid, the sensor can detect this behavior. If Flip to Start is enabled, the computer will respond by starting up automatically.

If you don’t like this feature, you can disable it. Flip to Start can be enabled and disabled in:

• Lenovo Vantage, Lenovo PC Manager or Lenovo Smart Engine

• Firmware Setup Utility

Customer replaceable units (CRUs) are parts that can be upgraded or replaced by the customer. A Lenovo computer may contain the following types of CRUs:

• Self-service CRU: Parts that can be installed or replaced easily by customer themselves or by trained service technicians at an additional cost.

• Optional-service CRU: Parts that can be installed or replaced by customers with a greater skill level. Trained service technicians can also provide service to install or replace the parts under the type of warranty designated for the customer’s machine.

The table below lists the CRUs defined for your product model.

Record product information and problem details before you contact support.

Product information

• Product name

• Machine type and serial number

Problem symptoms and details

• What is the problem? Is it continuous or intermittent?

• Any error message or error code?

• What operating system are you using? Which version?

• Which software applications were running at the time of the problem?

• Can the problem be reproduced? If so, how?

The product name and serial number can usually be found on the bottom of the computer, either printed on a label or etched on the cover.

Hotkey functions are denoted by the icons printed on the keys. The keyboard of your computer should only support a subset of the listed hotkeys.

Note: Hotkey functions may change if the associated app or the Windows operating system is updated.