FREE ENGLISH LENCO LED-4022BK (02) PDF USER GUIDE
FREE ENGLISH LENCO LED-4022BK (02) PDF USER MANUAL
FREE ENGLISH LENCO LED-4022BK (02) PDF OWNER GUIDE
FREE ENGLISH LENCO LED-4022BK (02) PDF OWNER MANUAL
FREE ENGLISH LENCO LED-4022BK (02) PDF REFERENCE GUIDE
FREE ENGLISH LENCO LED-4022BK (02) PDF INSTRUCTION GUIDE
FREE ENGLISH LENCO LED-4022BK (02) PDF REFERENCE MANUAL
FREE ENGLISH LENCO LED-4022BK (02) PDF INSTRUCTION MANUAL
FREE ENGLISH LENCO LED-4022BK (02) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD LENCO LED-4022BK (02) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
LENCO LED-4022BK (02) PDF SUMMARY:
How do I clean the TV?
Clean only with a slightly damp cloth. To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids. To remove severe stains, you may use a damp cloth with dilute detergent. Do not clean this product with water or other liquids.
What should I do before using the TV?
Read all of the instructions before using this TV and keep the instruction manual in a safe place for future reference.
What are some important safety instructions?
- Keep these instructions
- Do not use this TV near water.
- Clean only with a slightly damp cloth.
- Do not block any ventilation openings.
- Install in accordance with the supplied Quick Start Guide and this User Guide.
- Protect the power chord from being walked on or pinched, particularly at plugs, and the point where it exits from the TV.
- Do not allow the power chord to overhang the edge of a table.
- Unplug this TV during lightening storms or when unused for long periods of time.
- To prevent the spread of fire, keep candles or other open flames away from this product at all times.
What should I do if I notice smoke, an excessive build-up of heat or any other unexpected phenomena?
You should disconnect the plug from the main power socket immediately.
What should I do to ensure sufficient ventilation?
This device must be well ventilated at all time! Minimum distance of 10cm around the apparatus is needed for sufficient ventilations. The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths, curtains etc.
What should I do when pulling the plug out of the main supply socket?
Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short circuit.
What should I do to protect the device during a thunderstorm?
To protect the device during a thunderstorm, unplug the ac power adaptor.
What should I do to disconnect the power input completely?
To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the mains, as the disconnect device is the mains plug of apparatus. The mains plug of the apparatus should not be obstructed or should be easily accessed during intended use.
What should I do before checking the mains voltage?
Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.
Where do I connect a Satellite signal?
Connect a Satellite signal to DVB-S2.
Where do I connect headphones or other audio equipment?
Connect it to the headphone or other audio equipment at the 0 port.
Where do I connect a PC for display?
For PC display, connect it to the D-Sub 15 pins analog output connector of the PC.
Where do I connect a DVD player or other equipment?
Connect them to the SCART video output terminal of DVD or other equipment.
Where do I connect the audio output terminal of a PC?
Connect it to the audio output terminal of PC.
Where do I connect the HDMI of DVD or other equipment?
Connect it to the HDMI of DVD or other equipment.
Where do I connect a USB device for multimedia?
Connect to USB device for multimedia.
Where do I connect the audio & video output terminal of a DVD player?
Connect it to the audio & video output terminal of DVD with the Converter cable. (Audio terminals are shared with YPbPr).
Where do I connect the YPbPr video output terminal of a DVD player?
Connect it to the YPbPr video output terminal of DVD with the Converter cable.
What is the Common Interface slot for?
Cl+ slot.
How does the remote control work?
The remote control is using lnfra-Red(IR). Point it towards the front of the LED TV. The remote control may not work correctly if it is operated out of range or out of angle.
How do I turn the TV on/standby using the remote control?
Press the POWER button.
How do I mute the sound using the remote control?
Press the MUTE button to mute the sound, press again or press VOL+ to unmute.
How do I display the input source menu using the remote control?
Press the INPUT button.
How do I display the current mode’s information using the remote control?
Press the DISPLAY button.
How do I access the system setup menu using the remote control?
Press the MENU button.
How do I exit the OSD menu using the remote control?
Press the EXIT button.
How do I display the favorite program list using the remote control?
Press the FAV button.
How do I select a TV channel directly using the remote control?
Press the NUMBER BUTTONS 0-9.
How do I return to the previous channel viewed using the remote control?
Press the c.~ button.
How do I navigate the on-screen menus and adjust the system settings to your preference using the remote control?
Allows you to navigate the on-screen menus and adjust the system settings to your preference using the CURSOR KEYS<•’ "’ ’ ◄ ’ ► ’ OKl.
How do I select the language to be used for menus and messages?
Press ◄ / ► button to select the language.
How do I select the country?
Press T /…,. button to highlight country menu, then press ◄ / ► button to select the country you want. Press OK for Auto Tuning.
How do I perform Air(DVB-T) Auto Tune?
Select DTV+ATV in “Tune Type”, and DVB-Tin Digital Type, then press OK to start tuning.
How do I perform Cable (DVB-C) Auto Tune?
Select DVB-C in “Digital Type”:
There are 2 options for DVB-C “Scan Type”:
- Full: Select "FULL"in "Scan Type"and choose “OK” to start Auto Search for the channels.
- Network Scan: Select “Network Scan” in “Scan Type” Input the number of the Network ID of the channel and choose the frequency and press “OK” button to find specific TV channel. (Please notice you need to know the Network ID + Frequency+Symbol Rate from your TV provider).
How do I perform Satellite(Auto Tune)?
Select “Satellite” in “Digital Type”.
How do I display the main menu?
Press MENU button.
How do I select CHANNEL in the main menu?
Press ◄/► button to select CHANNEL in the main menu.
(Apply to DVL-3252WH, DVL-3252BK) How do I adjust the option that you want to adjust in the CHANNEL menu?
- Press ▼/▲ button to select the option that you want to adjust in the CHANNEL menu.
- Press OK button to select.
- After finishing your adjustment, Press OK button to save and return to the previous menu.
How do I perform ATV Manual Tuning?
Press MENU, then choose ATV Manual Tuning.
How do I set the channel number?
Current CH Set the channel number.
How do I select the color system?
Color System Select the color system (Available System: AUTO, PAL, SECAM)
How do I select the Sound system?
Sound System Select the Sound system
How do I adjust the frequency of the channel finely?
Fine-Tune Adjust the frequency of the channel finely.
How do I start searching channel?
Search Start searching channel by presing ► button. Once a channel is found, it will automatically stored. Repeat the step by changing the channel number.
How do I perform DVB-T Manual Tuning?
Enter the DTV Manual Tuning. Press ◄/► button to adjust the channel and press OK button to manual tune.
How do I perform DVB-C Manual Tuning?
Enter the CADTV Manual Tuning. Press ▲/▼ button to select the item and press ◄/► button to adjust the “Frequency”, “Symbol”, “QAM Type” and press OK button to manual tune.
How do I enter sub-menu Program Edit?
Press ▼/▲ button to select Program Edit, then press OK button to enter sub-menu.
How do I program the channel?
The three colored key is the shortcut key for programming the channel. First press ▼/▲ to highlight the channel you want to select, then:
- Press the Red button to delete the program in the list.
- Press the Yellow button to move the channel in favorite list.
- Press the Blue button to skip the selected channel.
- Press Fav button to add or remove the channel to/from your favorite list. (Your TV set will skip the channel automatically when using CH+/- to view the channels.)
How do I see the detail information about the signal?
Signal Information Press ▼/▲ button to select Signal Information, press the OK button to see the detail information about the signal. Only available when there is signal in DTV.
How do I select PICTURE in the main menu?
Press ◄/► button to select PICTURE in the main menu.
How do I adjust the option that I want to adjust in the PICTURE menu?
- Press ▼/▲ button to select the option that you want to adjust in the PICTURE menu.
- Press OK button to adjust.
- After finishing your adjustment, Press MENU button to save and return back to the previous menu.
How do I enter the Picture Mode sub-menu?
Press ▼/▲ button to select Picture Mode, then press OK button to enter sub-menu. You can change the value of contrast, brightness, color, sharpness and tint when the picture is in Personal mode.
How do I change the Picture Mode directly?
You can press PMODE button.
How do I adjust Contrast/Brightness/Color/Tint/Sharpness?
Press ▼/▲ button to select option, then press ◄/► button to adjust.
- Contrast: Adjust the contrast intensity of the picture, but the shadow of the picture is invariable.
- Brightness: Adjust the brightness output of the entire picture.
- Color: Adjust the saturation of the color.
- Tint: Adjust the compensating color change.
- Sharpness: Adjust the sharpness in the detail of the picture.
How do I change the overall colorcast of the picture?
Change the overall colorcast of the picture by pressing ▼/▲ button to select Color Temperature, then press OK button to enter sub-menu. Press ◄/►button to select. (Available color temperatures: Cool, Medium, Warm). You can change the value of red, green and blue when the color temperature is in User mode.
- Cold: Increase the blue tone for the white.
- Normal: Increase the Six-linked colors for the white.
- Warm: Increase the red color for the white.
How do I filter out and reduces the image noise and improve picture quality?
To filter out and reduces the image noise and improve picture quality, press ▼/▲ button to select Noise Reduction, then press OK button to enter sub-menu.
- Off: Select to turn off video noise detection.
- Low: Detect and reduce low video noise.
- Middle: Detect and reduce moderate video noise.
- High: Detect and reduce enhanced video noise.
- Default: Set as Default.
How do I select SOUND in the main menu?
Press ◄/► button to select SOUND in the main menu.
How do I adjust the option that you want to adjust in the SOUND menu?
- Press ▼/▲ button to select the option that you want to adjust in the SOUND menu.
- Press OK button to adjust.
- After finishing your adjustment, Press OK button to save and return to the previous menu.
How do I enter the Sound Mode sub-menu?
Press ▼/▲ button to select Sound Mode, then press OK button to enter sub-menu. Press ▼/▲ button to select. You can change the value of Treble and Bass when the sound is in Personal mode.
How do I change the Sound Mode directly?
You can press the Sound button on the remote control.
What are the different Sound Mode options?
- Standard: Produces a balanced sound in all environments.
- Music: Preserves the original sound. Good for musical programs.
- Movie: Enhances treble and bass for a rich sound experience.
- Sports: Enhances vocals for sports.
- Personal (user-defined): Select to customize sound settings.
Note: The treble and bass are only available in User mode, you can adjust them as you like.
How do I adjust Balance?
Balance: Press ▼/▲ button to select option, then press ◄/► button to adjust.
How do I select Auto Volume level?
Auto Volume level: Press ▼/▲ button to select Auto Volume Level, then press ◄/► button to select On or Off.
How do I select SPDIF Mode?
SPDIF Mode: Press ▼/▲ button to select SPDIF Mode, then press ◄/► button to select Off/PCM/Auto.
How do I select AD Switch?
AD Switch: Press ▼/▲ button to select AD Switch, then press ◄/► button to select On or Off. Amblyopia function for the blind, the tracks will be mixed describe the current screen. It need code stream to support.
How do I select TIME in the main menu?
Press ◄/► button to select TIME in the main menu.
How do I adjust the option that you want to adjust in the TIME menu?
- Press ▼/▲ button to select the option that you want to adjust in the TIME menu.
- Press OK button to adjust.
- After finishing your adjustment, Press OK button to save and return to the previous menu.
How do I select time zone?
Time Zone: Press ▼/▲/◄/► button to select time zone, then press “OK” button to confirm selection and enter the sub-menu.
How can I use the common interface slot to view pay TV programs?
- Turn on the TV and ensure "DTV’ Source is selected.
- If the CAM is detected the TV will display the following message on the screen: ··common Interface Module inserted "wait for a few moments until the card is activated.
- Select the relevant digital Pay Per View channel.
- Detailed information on the Smart Card in use is displayed
- Press the Ok button to access the card menu. Refer to the Module Instruction Manual for setting details.
- When the module is removed, the following message will appear on the screen: ··common Interface module removed".
How do I set the Sleep Timer?
Press the ▼/▲ button to select Sleep Timer, then press the “OK” button to confirm the selection and enter the sub-menu. Available options are: Off, 10min, 20min, 30min, 60min, 90min, 120min, 180min, 240min.
How do I use Auto Standby?
Press the ▼/▲ button to select Auto Standby, then press the “OK” button to confirm the selection and enter the sub-menu. If the remote control is used during the standby time, it will restart again from zero.
How do I use the OSD Timer?
Press the ▼/▲ button to select OSD Timer, then press the “OK” button to confirm the selection and enter the sub-menu.
How do I access the Lock Menu?
Press the MENU button to display the main menu. Press the ◄/► button to select Lock in the main menu.
How do I adjust options in the LOCK SYSTEM menu?
- Press the ▼/▲ button to select the option that you want to adjust in the LOCK SYSTEM menu.
- Press the OK/◄/► button to adjust.
- After finishing the adjustment, press the MENU button to return to the previous menu.
How do I use the Lock System?
Press the ▼/▲ button to select Lock System, then press the OK button to make the following 3 options valid. The default password is 0000.
How do I set a new password?
Press the ▼/▲ button to select Set Password, then press the OK button to enter the sub-menu to set a new password.
How do I use Channel Lock?
Press the ▼/▲ button to select Channel Lock, then press the OK button to enter the sub-menu to select. Press the Green button to lock or unlock the channel.
How do I use Parental Guidance?
Press the ▼/▲ button to select Parental Guidance, then press the OK button to enter the sub-menu to select the number of age which is suitable for your children.
How do I use Key Lock?
Press the ▼/▲ button to select Key Lock, then press the ◄/► button to select Off or On. When Key Lock’s statue is on, you can’t use the Key panel button.
How do I access Hotel Mode?
- Press the ▼/▲ button on the remote control to select hotel mode in the Lock menu.
- Press the OK button on the remote control to enter the sub-menu.
- After finishing the adjustment, press the MENU button to save and return to the previous menu.
How do I turn on/off Hotel Mode?
Press the ▼/▲ button to select Hotel Mode, then press the ◄/► button to select on or off.
How do I use Source Lock?
Press the ▼/▲ button to select Source Lock, then press the OK button to enter the sub-menu to select.
How do I use Default Source?
Press the ▼/▲ button to select Default Source, then press the OK button to enter the sub-menu to select.
How do I use Default Prog?
Press the ▼/▲ button to select Default Prog, then press the ◄/► button to adjust. It is available when the default source is TV.
How do I adjust Max Volume?
Press the ▼/▲ button to select Max Volume, then press the ◄/► button to adjust.
How do I use Clear Lock?
Press the ▼/▲ button to select Clear Lock, then press the OK button to clear the setting you have done before.
How do I access the Setup Menu?
Press the MENU button to display the main menu. Press the ◄/► button to select SETUP in the main menu.
How do I adjust options in the SETUP menu?
- Press the ▼/▲ button to select the option that you want to adjust in the SETUP menu.
- Press the OK button to adjust.
- After finishing the adjustment, press the OK button to save and return to the previous menu.
How do I select the OSD Language?
Select an OSD menu language can be displayed. Default German (Deutsch) is selected as menu language. Press the ▼/▲/◄/► button to select Menu Language.
How do I use TT Language?
Press the ▼/▲ button to select TT Language, then press the OK button to enter the sub-menu. Press the ▼/▲/◄/► button to select TT language.
How do I use Audio Languages?
Press the ▼/▲ button to select Audio Languages, then press the OK button to enter the sub-menu. Press the ◄/► button to select the primary of Audio Languages. Press the ▼/▲/◄/► button to select the Audio Languages.
How do I use Subtitle Language?
Press the ▼/▲ button to select Subtitle Language, then press the OK button to enter the sub-menu. Press the ◄/► button to select the primary of Subtitle Language. Press the ▼/▲/◄/► button to select the Subtitle Language.
How do I turn Hearing Impaired on or off?
Press the ▼/▲ button to select Hearing Impaired, then press the OK button to select On or Off.
How do I use Aspect Ratio?
Press the ▼/▲ button to select Aspect Ratio, then press the OK button to enter the sub-menu. Press the ▼/▲ button to select aspect ratio. Available options are: Auto, 4:3, 16:9, Zoom1, Zoom2.
How do I turn Blue Screen on or off?
Press the ▼/▲ button to select Blue Screen, then press the OK button to select On or Off.
How do I start First Time Installation?
Press the ▼/▲ button to select First time installation, then press the OK button to enter.
How do I Reset?
Press the ▼/▲ button to select Reset, then press the OK button to enter sub-menu.
How do I update the software via USB?
Press the ▼/▲ button to select Software Update (USB), plug your USB device in the USB slot, then press the OK button to update the right software.
How do I use HDMI CEC?
Press the ▼/▲ button to select HDMI CEC, then press the OK button to enter the sub-menu.
How do I turn the CEC Control on or off?
Press the ◄/► button to turn the CEC Control on or off.
How do I turn the Audio Receiver on or off?
Press the ◄/►button to turn the Audio Receiver on or off.
How do I turn the Device Auto Power Off on or off?
Press the ◄/► button to turn the Device Auto Power Off on or off.
How do I turn the TV Audio Power Off on or off?
Press the ◄/► button to turn the TV Audio Power Off on or off.
How do I open the main menu of a device?
Press the OK button to open the main menu of the device.
How do I open the Device Menu?
Press the OK button to open the Device Menu.
How do I access the Screen Menu under PC mode?
Press INPUT, choose PC. Press the MENU button to display the main menu.
How do I adjust options in the SCREEN menu?
- Press the ▼/▲ button to select the option that you want to adjust in the SCREEN menu.
- Press the OK button to adjust.
- After finishing the adjustment, press the OK button to save and return to the previous menu.
How do I start adjusting H-Offset/V-Offset/Size/Phase automatically?
Press the OK button to start adjusting H-Offset/V-Offset/Size/Phase automatically.
How do I adjust the horizontal position of the picture (H-Offset)?
Press the ◄/► button to select H-Offset, then press the OK button to enter the sub-menu.
How do I adjust the vertical position of the picture (V-Offset)?
Press the ◄/► button to select V-Offset, then press the OK button to enter the sub-menu.
How do I adjust the display size?
Press the ◄/► button to select Size, then press the OK button to enter the sub-menu.
How do I adjust the horizontal interfering lines (Phase)?
Press the ◄/► button to select Phase, then press the OK button to enter the sub-menu.
How do I use Position Reset?
Press the OK button to select Position Reset, then press the OK button to enter.
How do I operate the Media menu?
- Plug in the USB device.
- Press the INPUT button to set the Input Source to Media.
- Press the ▼/▲ button to select Media in the Source menu, then press the OK button to enter.
- Press the ◄/► button to select the option you want to adjust in the main Media menu, then press the OK button to enter.
How do I use the Photo Menu?
- Press the ◄/► button to select PHOTO in the main menu, then press the OK button to enter.
- Press the Exit button to return to the previous menu and the exit menu to quit.
- Press the ◄/► button to select the file you want to watch in the file selecting menu, then press the media button to display the picture.
- When highlighting the option you select, the file information will appear on the right and the picture will be previewed in the center.
How do I use the Music Menu?
- Press the ◄/► button to select MUSIC in the main menu, then press the OK button to enter.
- Press the Exit button to return to the previous menu and the exit menu to quit.
- Press the ◄/► button to select the drive disk you want to watch, then press the OK button to enter.
- Press the ◄/► button to select the return option to the previous menu.
How do I use the Movie Menu?
- Press the ◄/► button to select MOVIE in the main menu, then press the OK button to enter.
- Press the Exit button to return to the previous menu and the exit menu to quit.
- Press the ◄/► button to select the drive disk you want to watch, then press the OK button to enter.
- Press the media button to play the selected movie.
- Press the display button to select the menu in the bottom you want to run, then press the OK button to operate.
- Press the Exit button to return to the previous menu and the exit menu to quit.
How do I use the Text Menu?
- Press the ◄/► button to select TEXT in the main menu, then press the OK button to enter.
- Press the Exit button to return to the previous menu and the exit menu to quit.
- Press the ◄/► button to select the drive disk you want to watch, then press the OK button to enter.
- Press the ◄/► button to select the return option to the previous menu.
How do I operate the DVD player?
- Basic Operation
- Press the Power button on the TV or the remote control, then press the INPUT button to select DVD mode.
- If there is no disc in the DVD player the screen will show “NO DISC”.
- Insert Disc according to picture next to disc slot. Do not touch the playing surface.
- Hold the disc around the outside with your fingers and place the disc into the slot.
- The player will automatically draw the disc into the player.
- To “Eject” the disc, press the EJECT button on the TV or the " " button on the remote control.
- Disc Eject
- If not in DVD-mode, press the INPUT-key on the remote and select DVD.
- Press OK.
- Press the -key on the remote.
- The disc ejects.
- Return to Tuner-mode (watch TV)
- Press the INPUT-key on the remote. See the INPUT SOURCE window appear.
- Select DTV or Satellite and press the OK-key.
How do I use DVD Setup Mode?
- Setup Mode provides the menu for the configuration of General Setup Page, Audio Setup Page, Dolby Digital Setup, Preference Page.
- Item selection in the Setup Menu is done by using the Navigation Arrows, SETUP button, and the OK button.
- Press the SETUP button first, enter into the SETUP menu, then press the DIRECTION RIGHT button, you can enter into the next Sub-menu.
- Press the SETUP button again to exit the Setup Menu.
What are the TV Display options under General Setup?
- 4:3 PS: This is selected when the DVD player is connected to a normal TV. Wide-screen images are shown on the screen, but with some parts cut automatically.
- 4:3 LB: This is selected when the player is connected to a normal TV. Wide-screen images are shown on the screen, with black belt on the top and bottom.
- 16:9: This is selected when the player is connected to a wide-screen TV.
How do I select the OSD Language for DVD operation?
This is used to select the OSD language.
How do I use the Screen Saver?
Start the screen saver, the screen saver image will appear when the player stops or the picture is frozen for a few minutes. This saver can keep the screen from being damaged.
- On (Start the screen saver)
- Off (Remove the screen saver).
How do I use Last Memory?
Can set the items on the last memory, “on” and “off” option.
- On (Start the memory): The DVD will start playing at the last time position of previous play.
- Off (Remove the memory): When turning on the DVD, the last position will not be remembered.
How do I access the Speaker Setup Page?
In the “Audio Setup page” press the “▼” button to select the “Speaker Setup” item, press the “OK ENTER” or “►” button (play) into the “Speaker Setup Page”.
What are the Downmix options for audio?
- Surround: A disc recorded with a multi-channel soundtrack; the output signal will be converted to the left and right channels.
- Stereo: A disc recorded with a multi-channel soundtrack; the output signal will be converted to stereo.
How do I use Dynamic Range Control in Dolby Digital Setup?
This option is used to set the compression ratio in order to control the sound contrast.
How do I enter the Preference Page?
You must press STOP twice to enter the Preference Page or with NO disc.
What are the TV Type options in Preference Setup?
- PAL: This is selected when the player is connected to a PAL System TV.
- AUTO: The player will set the TV system according to the disc in the tray.
- NTSC: This is selected when the player is connected to a NTSC System TV.
How do I set the Audio language preference?
If a language listed below is recorded on the disc, you can play the sound in such language. If not, the language recorded will be used.
How do I set the Subtitle language preference?
If a language listed below is recorded on the disc, you set the subtitle to be displayed in such language. If not, the language recorded will be used.
How do I set the Disc Menu language preference?
If a language listed below is recorded on the disc, you can set the Menu to be displayed in such language. If not, the language recorded will be used.
CLICK HERE TO DOWNLOAD LENCO LED-4022BK (02) PDF MANUAL