LEAPFROG LF930HD (01) PDF MANUAL

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the Baby Unit at a height above 2 meters.

4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such.

5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the Parent Viewer.

7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning. Use a damp cloth for cleaning.

11. Warning-Strangulation Hazard-Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove the tag.

12. Never place the Baby Unit(s) inside the baby’s crib or playpen. Never cover the Baby Unit(s) or Parent Viewer with anything such as a towel or a blanket.

13. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

To start monitoring from anywhere, you can download the free LeapFrog Baby Care mobile app.

Search for “LeapFrog Baby Care” on the Apple App Store or Google Play Store.

The app is compatible with:

• Android™ 6.0 or later

• iOS 12.0 or later

Connect the power adapters for the Baby Unit and Parent Viewer to the units and to power outlets. Ensure the power adapters are plugged in correctly.

Charging Instructions:

Before using the baby monitor for the first time, charge the Parent Viewer battery for 12 hours. The standby time varies depending on your actual usage time and the age of the battery.

Battery Status Indicators:

The battery icon on the screen indicates the battery status.

To Power On/Off the Baby Unit:

1. Slide the On/Off switch to ON to power on your Baby Unit. The POWER LED light is off by default.

2. To power off, slide the On/Off switch to OFF.

To Power On/Off the Parent Viewer:

1. Press and hold the POWER button until the welcome screen appears.

2. To power off, press and hold the POWER button until the screen turns off.

Once your Baby Unit and Parent Viewer are powered on and connected, your Parent Viewer displays video from the Baby Unit, and the LINK LED light turns on.

Positioning:

Keep the Baby Unit more than 3 feet (1 meter) away from your baby.

Caution for Noise:

The default volume of your Parent Viewer is level 3, and the maximum volume is level 5. If you experience a screeching noise from your baby monitor while positioning, you should:

• Make sure your Baby Unit and Parent Viewer are more than 3 feet (1 meter) apart, OR

• Lower the volume of your Parent Viewer.

Avoiding Interference:

To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, mobile phones and computers.

To ensure cords are managed safely and kept out of reach, you can use the provided materials to secure the cables along the wall.

• Night Mode quick set key: Select black-and-white or color night vision viewing mode. Adjust night light brightness.

• Arrow Keys: Navigate menus and pan/tilt the baby unit camera.

• Menu/Select: Press to enter or exit the menu. In a menu, press to choose an item, or save a setting.

• TALK / RETURN: Press and hold to talk to the baby unit. In a menu, press to return to the previous screen.

• VOL: View the volume adjustment bar and change the volume level.

• Zoom: Press to zoom in or out.

• Power/LCD Off: Press and hold to turn on/off. Press to turn the LCD screen off.

• RESET: Force reboot the Parent Viewer by pressing the key on the back.

• Night light control key: Press to turn the night light on or off. Press and hold to adjust the night light brightness level.

• On/Off switch: Slide to turn the unit on or off.

• PAIR key: The Parent Viewer and Baby Unit(s) provided are already paired. You may need to press and hold this key if you need to re-pair the units.

Direct mode: The Parent Viewer and the Baby Unit are pre-paired and can connect to each other directly by default. This allows you to stream live video right out of the box.

Wi-Fi Router mode: This mode uses your home Wi-Fi network to connect your baby monitor system. It enhances your local access by extending the connection range. With the LeapFrog mobile app, your Wi-Fi router also provides Internet connectivity, allowing you to control your Baby Unit from anywhere.

If you plan to install your Baby Unit in a designated location and will use your home Wi-Fi network to connect your video monitor, test whether your selected monitoring areas have good Wi-Fi signal strength.

Adjust the direction and distance between your Baby Unit, Parent Viewer, and Wi-Fi router until you have identified a suitable location with a good connection.

Ensure your wireless connection is secure:

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK with AES” setting in your router’s wireless security menu.

Change default settings:

• Change your wireless router’s default wireless network name (SSID) to something unique.

• Change default passwords to unique, strong passwords.

Keep your devices up to date:

• Download security patches from manufacturers as soon as they become available. Enable automatic updates for future releases if available.

Disable Universal Plug and Play (UPnP) on your router:

• UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network devices to open inbound ports without any intervention or approval from you.

Parking Mode is designed to give you extra peace of mind. When turned on, the Baby Unit will fold into the parking position and disable its camera’s audio transmission and video monitoring. Motion recording, motion detection, and sound detection will be temporarily unavailable.

Activate Parking Mode:

1. Press MENU to enter the main menu.

2. Go to Baby Unit Settings.

3. Go to Parking Mode and press to toggle the switch on.

To deactivate Parking Mode and resume normal operation, press the TALK button on the Parent Unit.

In the main menu, under Monitoring mode, you can select:

• Single mode: View Baby Units in Single mode.

• Patrol mode: View Baby Units in Patrol mode.

• Split screen: View Baby Units in Split screen.

In the main menu, select Night light. From here you can:

• Turn on/off night light.

• Select a night light color.

• Adjust brightness.

• Set a Timer to turn the night light off.

In the main menu, select Lullaby. From here you can:

• Play/Stop lullaby.

• Select to play all melodies, or play one of the 5 melodies and 5 soothing sounds.

• Set a Timer to stop the lullaby.

• Set the lullaby volume.

In the main menu, select Detection – Sound, motion, temperature. From here you can:

• Select the sound and motion sensitivity level.

• Turn on/off sound and motion detection alerts.

• Turn on/off Auto Wake-up feature.

• Turn on/off Temperature Alert.

• Select the minimum and maximum Temperature range.

• Change the Temperature display format (Fahrenheit or Celsius).

In the main menu, select Parent Unit settings. From here you can adjust:

• Parent Unit screen brightness.

• Turn on/off Low Battery Alert Tone.

• Turn on/off No Link Alert Tone.

• Turn on/off Dim Mode.

In the main menu, select Baby Unit settings. From here you can adjust:

• Parking Mode.

• LED Status.

• Baby Unit’s speaker volume.

• Security Key.

• Direct mode: The parent unit and baby unit(s) are connected to each other directly.

• Wi-Fi Router mode: The parent unit and baby unit(s) are connected to the home Wi-Fi network.

• Patrol mode: Baby units are being viewed in Patrol mode (*For LF930-2HD only).

• Split mode: Baby units are being viewed in Split mode (*For LF930-2HD only).

• B/W night vision: Black and white night vision is turned on.

• Color night vision: Color night vision is turned on.

• Motion detection alert: This alert is turned on.

• Lullaby: Melodies and soothing sounds are playing.

• Night light: The night light is turned on.

• Auto night light brightness: This feature is activated.

• Muted: The parent unit speaker is muted.

• Temperature alert: This alert is turned on.