KUSSMAUL PURE SINE WAVE 450-1500-0 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KUSSMAUL PURE SINE WAVE 450-1500-0 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** INSTRUCTION MANUAL INVERTER PURE ‘NAVE 700/1000/1500/2000/3000/4000 MODEL MODEL MODEL MODEL MODEL MODEL Fila: Pavised aye: SO 170 Cherry Avenue West Sayville, NY 11796 kussmaul.com 450- 45 0 0700-0 1 000-0 1 500-0 2000-0 3000-0 o 700 Watt 1 OOO Watt 1 SOO Watt 2000 Watt 3000 Watt 4000 Watt 1 ral(USSMAlJt ELECTRONICS ENERGIZED AND READY WHEN SECONDS COUNT Ph: 800-346-0857 Fax: 631-567-5826 sales@kussmaul.com

****** Page 2 ****** Table of Content 1. SAFETY INSTRUCTIONS 1-1. General Safety Precautions 1-2. Other Safety Notes 2. FUNCTIONAL CHARACTERISTICS INTRODUCTION 2-1. System 2-2. Block Diagram 2-3. Electrical Specification 2-3-1. 450-0700-0 Specification (700 WATT, 100-120 VAC) 2-3-2. 450-0700-0 Specification (700 WATT, 200-240 VAC) 2-3-3.450-1000-0 Specification (1000 WATT, 100-120 VAC) 2-3-4.450-1000-0 Specification (1 OOO WATT, 200-240 VAC) 2-3-5.450-1500-0 Specification (1500 WATT, 100-120 VAC) 2-3-6.450-1500-0 Specification (1500 WATT, 200-240 VAC) 2-3-7. 450-2000-0 Specification (2000 WATT, 100-120 VAC) 2-3-8. 450-2000-0 Specification (2000 WATT, 200-240 VAC) 2-3-9. 450-3000-0 Specification (3000 WATT, 100-120 VAC) 2-3-10. 450-3000-0 Specification (3000 WATT, 200-240 VAC) 2-3-11. 450-4000-0 Specification (4000 WATT, 100-120 VAC) 2-3-12. 450-4000-0 Specification (4000 WATT, 200-240 VAC) 2-3-13. Voltage & temperature performance 2-4. Mechanical Drawings 3. INSTALLATION AND MAINTENANCE 3-1. AC Output Side (Front Panel) Introduction 3-1-1. Main Switch 3-1-2. LED Indicator 3-1-3. Function Switch Introduction 1 1 1 3 3 3 4 4 5 7 8 10 11 13 14 16 19 20 22 23 24 24 25 25 26

****** Page 3 ****** 3-1-4. TRC Port (for optional kits TR-40, RJ-45) 3-1-5. AC output Interface 3-2. DC Input Side (Rear Panel) Introduction 3-2-1. Remote Port (RJ-II) 3-2-2. Remote Control Green Terminal 3-2-3. General instruction before DC Input 3-2-4. Chassis Ground O 3-3. Maintenance 4. OPERATION 4-1. Connection the DC cable 4-2. Connecting the input power 4-3. Connecting the loads 4-4. Switch ON Inverter 4-5. Protection Mechanism (4) 5. RS232 COMMUNICATION AND OPERATION 5-1. RS232 Port 5-2. RS232 Port Operating 5-3. Example of RS232 Port Operating 5-3-1. RS232 command format 5-3-2. Command format 6. INFORMATION 6-1. Warning 6-2. Warranty 27 28 29 31 31 32 33 33 34 34 35 35 35 36 36 36 37 37 37 38 41 41 41

****** Page 4 ****** 1. Safety Instructions 1-1. General Safety Precautions Warning! Before using the Inverter, read the safety instructions. Do not expose the inverter to rain, snow, spray or dust. To reduce the risk of fire hazard, do not cover or obstruct the ventilation openings and do not install the inverter in a zero-clearance compartment. To avoid the risk of fire and electric shock, make sure that the existing wiring is in good electrical condition, and the wire size is not undersized. This equipment contains components which can produce arcs or sparks. To prevent fire or explosion do not install in compartment containing batteries or flammable materials or in location which require ignition protected equipment. This includes any space containing gasoline-powered machinery, fuel tanks, or joints, fittings, or other connection between components of the fuel system. Depending on the user scenario, the AC output of the inverter may require user installed breaker or fuse. In AC output hardwire application, AC socket will not been provided. The inverter incorporates standard AC short circuit protection. The following precautions should be taken when working on the inverter: Stepl Remove watches, rings, or other metal objects Step 2 Use tools with insulated handles Step 3 Wear rubber gloves and boots 1-2. Other Safety Notes Upon receipt, examine the carton box for damage. If you have found any damage on the carton box please notify the company you purchased this unit from. 1

****** Page 5 ****** Do not operate near water or in excessive humidity. Do not open or disassemble the inverter, and warranty may be voided. The DC side connections should be firm and tight. Grounding: Reliable grounding should be maintained. Do not drop a metal tool on the battery. The resulting spark or short-circuit on the battery or on the other electrical part may cause an explosion. Install the inverter in a well-ventilated area. Do not block the front air vents, or the rear air exhausts of the unit. Wiring: Adequate input power must be supplied to the inverter for proper use; correct wiring sizes must be ensured. Mount the inverter such that the fan axis is horizontal. Do not operate the inverter close to combustible gas or open fire. Do not operate appliances that may feed power back into the inverter. Temperature: The inverter should be operated in an ambient temperature range of -20 C to 400C othemse the output efficiency may be affected. Air flow to the inverter must not be blocked. 2

****** Page 6 ****** 2. Functional Characteristics Introduction 2-1. System The unit is a highly reliable DC-AC inverter system, designed with advanced power electronic and microprocessor technology offering the following features: Pure sine wave output (T HD < 5%) to operate Optional bypass relay(TR-40) function Intelligent software for power management Loading and temperature controlled cooling fan CR-8/CR-16 remote management and control RS232 communication Dry contact terminal Advanced Protection Features Input over/under voltage protection Internal over temperature protection Input reverse polarity protection (Fuse) Output overload protection Output short circuit protection 2-2. Block Diagram DC DC / DC INPUT DC / AC FILTER AC INPUT 3 ****** Page 7 ****** 2-3. Electrical Specification 2-3-1. 450-0700-0 Specification (700 WATT, I OO-120 VAC) Electrical Input Characteristics Output Characteristics Signal and Control Protection Environment 4 Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity 450-0700-0 12VDC 16.5 ± O.3VDC 10.5 ± O.3VDC@ 10.5&16.5VDC <1.5 A @12VDC <O.IA @12VDC Model No. 24 Volt: Inquire 48 Volt: Inquire 24VDC 33 ± O.5VDC 21 ± 0.5VDC@ 21-33VDC <0.8 A @24VDC <O.06A @24VDC 700 VA 48VDC 66 ± I.OVDC 42 ± I.OVDC@ 42-66VDC <0.5 A @48VDC 700 VA-BIO VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 100/ 110/ 115/ 120 VAC (± 5%) 88% (Dip Switch Selectable) 89% 1 Sec Shutdown 900/0 Pure Sine Wave (T HD < 5%@ Normal CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800C ) -20 Oce 30 C-70 C 10 -950/0 RH ****** Page 8 ****** Specification Electrical Item Safety Standards Safety & EMC EMC standards E-mark Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Model No. 24 Volt: Inquire 48 Volt, Inquire 450-0700-0 Certified UL 458 (UL only for GFCI receptacles) Certified FCC class B 200mm X 83mm X 330mm 2.6 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 1. 450-0700-0 for Output 100/110/115/120 VAC specification. Note O Voltage range : Please refer to Figure 1 O Normal load Condition : VIII =12.5V/25V/50V, Vo=100/llO/115/120VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 2-3-2. Specification (700 WATT, 200-240 VAC) Electrical Input Characteristics Output Characteristics Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Inquire 12VDC 16.5 ± 0.3VDC@ 10.5 ± O.3VDC 10.5-16.5VDC <1.5 A @12VDC <0.1 A @12VDC Model No. Inquire 24VDC 33 ± 0.5VDC@ 21 ± O.5VDC 21-33VDC <O.8A @24VDC <O.06A @24VDC 700 VA 3%) Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66VDC <0.5 A @48VDC 700 VA-810 VA (1000/0-115%) < 1230 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 200 / 220 / 230 / 240 VAC (Dip Switch Selectable) 5 ****** Page 9 ****** Electrical Output Characteristics Signal and Control Protection Environment Safety & EMC Specification Item Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Inquire Model No. Inquire 1 Sec Shutdown Inquire 900/0 Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Pure Sine Wave (T HD < 5%@ Normal CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800C /-200C) 40 @ 70 C 10-950/0 RH Certified EN 60950-1 Certified EN 55022; EN 55024; EN 61000-3-2, -3-3 EN 61000-4-2, 3, 4, 5, 6, 8, 11 Certified CISPR 25; ISO 11452-2; ISO 7637-2 200mm X 83mm X 330mm 2.6 KG Temperature & Load Controlled cooling Fan T R-40 (optional) Table 2. 450-0700-0 for Output 200/220/230/240 VAC specification. Note : O Voltage range : Please refer to Figure 1 @ Normal load Condition : vin =12.5V/25V/50V, vo=200/220/230/240 VAC Full load (PF=I .0) O Operating temperature : Please refer to Figure 2 6 ****** Page 10 ****** 2-3-3. 450-1000-0 Specification (1 OOO WATT, 100-120 VAC) Electrical Input Characteristics Output Characteristics Signal and Control Protection Environment Safety & EMC Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark 450-1000-0 12VDC 16.5 ± 0.3VDC@ 10.5 ± O.3VDC 10.5-16.5 VDC <1.5 A @12VDC <O.IA @12VDC Model No. Inquire 24VDC 33 ± O.5VDC@ 21 ± O.5VDC 21-33 VDC <0.8 A @24VDC <O.06A @24VDC 1000 3%) Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC <0.5 A @48VDC 1000 VA-1150 VA (1000/0-115%) < 1750 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 100/ 110/ 115/ 120 VAC (± 5%) 88% (Dip Switch Selectable) 89% 1 Sec Shutdown Pure Sine Wave (T HD < 5%@ Normal Load) a CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800C/-200C ) 20 C-40 ace -30 Oc 10-950/0 RH Certified UL 458 (UL only for GFCI receptacles) Certified FCC class B 7 ****** Page 11 ****** Specification Electrical Item Dimension(WxHxD Weight Cooling AC Transfer Function Accessories 450-1000-0 Model No. Inquire Inquire 200mm X 83mm X 372mm 3.26 KG Temperature & Load Controlled cooling Fan T R-40 (optional Table 3. SP-IOOO for Output 100/110/115/120 VAC specification. Note O Voltage range : Please refer to Figure 1 @ Normal load Condition : Vin =12.5V/25V/50V, Vo=100/110/115/120VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 2-34. Specification (1000 WATT, 200-240 VAC) Electrical Input Characteristics Output Characteristics 8 Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform In uire 12VDC 16.5 ± O.3VDC@ 10.5 ± O.3VDC 10.5-16.5 VDC <1.5 A @12VDC < 0.1A @12VDC Model No. In uire 24VDC 33 ± O.5VDC@ 21 ± O.5VDC 21-33 VDC <0.8 A @24VDC <O.05A @24VDC 1000 3%) In uire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC <0.4 A @48VDC 1000 VA-1150 VA < 1750 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 200 / 220 / 230 / 240 VAC (± 3%) 88% (Dip Switch Selectable) 89% 1 Sec Shutdown Pure Sine Wave (THD < 50/0@ Normal ****** Page 12 ****** Electrical Signal and Control Protection Environment Safety & EMC Specification Item Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Inquire Model No. Inquire CR-8 / CR-16 (optional) Inquire Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800/-200) 20 Oc-40 Oce 30 C-70 oc 10-950/0 RH Certified EN 60950-1 Certified EN 55022; EN 55024; EN 61000-3-2, -3-3 EN 61000-4-2, 3, 4, 5, 6, 8, 11 Certified CISPR 25; ISO 11452-2; ISO 7637-2 200mm X 83mm X 372mm 3.26 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 4. SP-IOOO for Output 200/220/230/240 VAC specification. Note O Voltage range : Please refer to Figure 1 O Normal load Condition : Vin =12.5V/25V/50V, VAC 800/0 Full load (PF=I .0) O Operating temperature : Please refer to Figure 2 9 ****** Page 13 ****** 2-3-5. 450-1500-0 Specification (1500 WATT, 100-120 VAC) Electrical Input Characteristics Output Characteristics Signal and Control Protection Environment 10 Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity 450-1500-0 12VDC 16.5 ± 0.3VDC@ 10.5 ± 0.3VDC 10.5-16.5 VDC <1.8A @12VDC <O.IA @12VDC Model No. Inquire 24VDC 33 ± 0.5VDC@ 21 ± 0.5VDC 21-33 VDC <0.9 A @24VDC <O.05A @24VDC 1500 3%) Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC <0.5 A @48VDC 1500 VA-1730VA <2650 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 100/ 110/ 115/ 120 VAC 5%) 88% (Dip Switch Selectable) 89% 1 Sec Shutdown 90% Pure Sine Wave (T HD < 5%@ Normal Load)@ CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800/-200 ) -20 Oce 70 10-950/0 RH ****** Page 14 ****** Specification Electrical Item Safety Standards Safety & EMC EMC standards E-mark Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories 450-1500-0 Model No. Inquire Inquire Certified UL 458 (UL only for GFCI receptacles) Certified FCC class B 248mm X 83mm X 421 mm 4.14 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 5. SP-1500 for Output 100/110/115/120 VAC specification. Note O Voltage range : Please refer to Figure 1 O Normal load Condition : VIII =12.5V/25V/50V, Vo=100/llO/115/120VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 2-3-6. Specification (1000 WATT, 200-240 VAC) Electrical Input Characteristics Output Characteristics Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Inquire 12VDC 16.5 ± 0.3VDC 10.5 ± O.3VDC@ 10.5-16.5 VDC <1.8A @12VDC <O.IA @12VDC Model No. Inquire 24VDC 33 ± 0.5VDC 21 ± O.5VDC@ 21-33 VDC <0.9 A @24VDC <O.05A @24VDC 1500 3%) Inquire 48VDC 66 ± I.OVDC 42 ± I.OVDC@ 42-66 VDC <0.5 A @48VDC 1500 VA-1730VA (1000/0-115%) <2650 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 200 / 220 / 230 / 240 VAC (Dip Switch Selectable) 11 ****** Page 15 ****** Electrical Output Characteristics Signal and Control Protection Environment Safety & EMC Specification Item Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Inquire Model No. Inquire 1 Sec Shutdown Inquire 900/0 Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Pure Sine Wave (T HD < 5%@ Normal CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / IJnder Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +80C/-20C ) -20 -30 OC-70 Oc 10 -950/0 RH Certified EN 60950-1 Certified EN 55022; EN 55024; EN 61000-3-2, -3-3 EN 61000-4-2, 3, 4, 5, 6, 8, 11 Certified CISPR 25; ISO 11452-2; ISO 7637-2 248mm X 83mm X 42 Imm 4.14 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 6. SP-1500 for Output 200/220/230/240 VAC specification. Note O Voltage range : Please refer to Figure 1 O Normal load Condition : Vin =12.5V/25V/50V, VAC 800/0 Full load (PF=I .0) O Operating temperature : Please refer to Figure 2 12 ****** Page 16 ****** 2-3-7. 450-2000-0 Specification (2000 WATT, 100-120 VAC) Electrical Input Characteristics Output Characteristics Signal and Control Protection Environment Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity 450-2000-0 12VDC 16.5 ± 0.3VDC@ 10.5 ± 0.3VDC 10.5-16.5 VDC <1.8 A @12VDC <O.IA @12VDC Model No. Inquire 24VDC 33 ± 0.5VDC@ 21 ± 0.5VDC 21-33 VDC <0.9 A @24VDC <O.05A @24VDC 2000 Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC <0.5 A @48VDC 2000 VA-2300 VA (1000/0-115%) < 3500 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 100/ 110/ 115/ 120 VAC 5%) 88% (Dip Switch Selectable) 89% 1 Sec Shutdown 90% Pure Sine Wave (T HD < 5%@ Normal Load)@ CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800/-200 ) -20 Oce 70 10-950/0 RH 13 ****** Page 17 ****** Specification Electrical Item Safety Standards Safety & EMC EMC standards E-mark Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories 450-2000-0 Model No. Inquire Inquire Certified UL 458 (UL only for GFCI receptacles) Certified FCC class B 248mm X 83mm X 443mm 5.24 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 7. SP-2000 for Output 100/110/115/120 VAC specification. Note O Voltage range : Please refer to Figure 1 O Normal load Condition : VIII =12.5V/25V/50V, Vo=100/llO/115/120VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 2-3-8. Specification (2000 WATT, 200-240 VAC) Electrical Input Characteristics Output Characteristics 14 Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Inquire 12VDC 16.5 ± 0.3VDC@ 10.5 ± 0.3VDC 10.5-16.5 VDC <1.8 A @12VDC <O.IA @12VDC Model No. Inquire 24VDC 33 ± 0.5VDC@ 21 ± 0.5VDC 21-33 VDC <0.9 A @24VDC <O.05A @24VDC 2000 Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC <0.5 A @48VDC 2000 VA-2300 VA (1000/0-115%) < 3500 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 200 / 220 / 230 / 240 VAC (± 3%) 89% (Dip Switch Selectable) 89% ****** Page 18 ****** Electrical Output Characteristics Signal and Control Protection Environment Safety & EMC Specification Item Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Inquire Model No. Inquire 1 Sec Shutdown Inquire Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Pure Sine Wave (T HD < 5%@ Normal Load) a CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / IJnder Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800C/-200C ) -20 oc-40 C @ 30 C-70 C 10 -950/0 RH Certified EN 60950-1 Certified EN 55022; EN 55024; EN 61000-3-2, -3-3 EN 61000-4-2, 3, 4, 5, 6, 8, 11 Certified CISPR 25; ISO 11452-2; ISO 7637-2 248mm X 83mm X 443mm 5.24 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 8. SP-2000 for Output 200/220/230/240 VAC specification. Note • O Voltage range : Please refer to Figure 1 @ Normal load Condition : Vln 12.5V/25V/50V, VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 15 ****** Page 19 ****** 2-3-9. 450-3000-0 Specification (3000 WATT, 100-120 VAC) Electrical Input Characteristics Output Characteristics Signal and Control Protection Environment 16 Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity 450-3000-0 12VDC 16.5 ± O.3VDCC 10.5 ± O.3VDC 10.5-16.5 VDC <3.8 A @12VDC <O.4A @12VDC Model No. Inquire 24VDC 33 ± O.5VDC@ 21 ± O.5VDC 21-33 VDC <1.9 A @24VDC <O.2A @24VDC 3000 Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC .O A @48VDC 3000 VA-3450 VA (1000/0-115%) < 6000 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 100/ 110/ 115/ 120 VAC 5%) 88% (Dip Switch Selectable) 89% 1 Sec Shutdown 90% Pure Sine Wave (T HD < 5%@ Normal Load)@ CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800/-200 ) -20 Oce 70 10-950/0 RH ****** Page 20 ****** Electrical Safety & EMC Specification Item Safety Standards EMC standards E-mark 450-3000-0 Model No. Inquire Inquire Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Certified UL 458 Certified FCC class A 255mm X 158mm X 442mm 8.2 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 9. SP-3000 for Output 100/110/115/120 VAC specification. Note O Voltage range : Please refer to Figure 1 O Normal load Condition : VIII =12.5V/25V/50V, Vo=100/llO/115/120VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 2-3-10. Specification (3000 WATT, 200-240 VAC) Electrical Input Characteristics Output Characteristics Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (1 sec) Frequency Output Voltage Inquire 12VDC 16.5 ± O.3VDCC 10.5 ± O.3VDC 10.5-16.5 VDC <3.8 A @12VDC <O.4A @12VDC Model No. Inquire 24VDC 33 ± O.5VDC@ 21 ± O.5VDC 21-33 VDC <1.9 A @24VDC <O.2A @24VDC 3000 Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC .O A @48VDC 3000 VA-3450 VA (1000/0-115%) < 6000 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 200 / 220 / 230 / 240 VAC (± 3%) (Dip Switch Selectable) 17 ****** Page 21 ****** Electrical Output Characteristics Signal and Control Protection Environment Safety & EMC Specification Item Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Inquire 89% Model No. Inquire 89% 1 Sec Shutdown Inquire Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Pure Sine Wave (T HD < 5%@ Normal Load)@ CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / IJnder Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800C/-200C ) -20 -30 OC-70 Oc 10-950/0 RH Certified EN 60950-1 Certified EN 55022; EN 55024; EN 61000-3-2, -3-3 EN 61000-4-2, 3, 4, 5, 6, 8, 11 Certified CISPR 25; ISO 11452-2; ISO 7637-2 255mm X 158mm X 442mm 8.2 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 10. SP-3000 for Output 200/220/230/240 VAC specification. Note : O Voltage range : Please refer to Figure 1 O Normal load Condition : Vin =12.5V/25V/50V, vo=200/220/230/240 VAC Full load (PF=I .0) O Operating temperature : Please refer to Figure 2 18 ****** Page 22 ****** 2-3-11. 4504000-0 Specification (4000 WATT, 100-120 VAC) Electrical Input Characteristics Output Characteristics Signal and Control Protection Environment Safety & EMC Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (ISec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel IJnit LED Indicator Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Model No. Inquire 24VDC 33 ± O.5VDCC' 21 ± O.5VDC 21-33 VDC < .9 A @24VDC <O.2A @24VDC Inquire 48VDC 66 ± I.OVDCC 42 ± I.OVDC 42-66 VDC <l.o A @48VDC 4000 VA-4600 VA (10096-115%) < 8000 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 100 / 110/ 115/ 120 VAC (± 5%) (Dip Switch Selectable) 88% 90% 1 Sec Shutdown Pure Sine Wave (THD < 50/0@ Normal Load)' CR-8 / CR-16 (optional) Red / Orange / Green LED By a relay 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / IJnder Temperature Protection (by Heat sink Temperature +800C/-200C ) -20 C-40 Oce -30 Oc 10-95% RH Certified UL 458 (Only for 115/120VAC) Certified FCC class A 19 ****** Page 23 ****** Specification Electrical Item Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories Model No. Inquire Inquire 255mm X 158mm X 462mm 10 KG Temperature & Load Controlled cooling Fan T R-40 (optional) Table 11. SP-4000 for Output 100/110/115/120 VAC Specification. Note O Voltage range : Please refer to Figure 1 @ Normal load Condition : Vin =25V/50V, Vo=100/110/115/120VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 2-3-12. Specification (4000 WATT, 200-240 VAC) Electrical Input Characteristics Output Characteristics Signal and Control 20 Specification Item Voltage Input Over-Voltage Protection Input Under-Voltage Protection Voltage Range No Load Current Power Saving Mode Continuous Output Power Maximum output Power (1 Min) Surge Power (ISec) Frequency Output Voltage Efficiency max. Short-Circuit Protection Output Waveform Remote Controller Panel Unit LED Indicator Model No. Inquire 24VDC 33 ± O.5VDCC' 21 ± O.5VDC 21-33 VDC < .9 A @24VDC <O.2A @24VDC Inquire 48VDC 66 ± I.OVDC@ 42 ± I.OVDC 42-66 VDC <l.o A @48VDC 4000 VA-4600 VA (10096-115%) < 8000 VA 50 / 60 Hz ± 0.5% (Dip Switch Selectable) 200 / 220 / 230 / 240 VAC (± 3%) (Dip Switch Selectable) 900/0 1 Sec Shutdown Pure Sine Wave (T HD < 5%@ Normal CR-8 / CR-16 (optional) Red / Orange / Green LED ****** Page 24 ****** Electrical Signal and Control Protection Environment Safety & EMC Specification Item Dry Contact Terminal Remote Control Terminal Input Protection AC Output Protection Others Operating Temp. Storage Temp. Storage Temp. & Humidity Safety Standards EMC standards E-mark Model No. Inquire By a relay Inquire Dimension(WxHxD) Weight Cooling AC Transfer Function Accessories 6-port Green terminal (for inverter ON / OFF) Over / Under Voltage, Reverse Polarity (Internal Fuse) Short-Circuit, Overload Over / Under Temperature Protection (by Heat sink Temperature +800C/-200C ) -20 C-40 Oce -30 Oc 10 -95% RH Certified EN 60950-1 Certified EN 55022; EN 55024; EN 61000-3-2, -3-3; EN 61000-4-2, 3, 4, 5, 6, 8, 11 Certified CISPR 25; ISO 11452-2; ISO 7637-2 255mm X 158mm X 462mm 10 KG Temperature & Load Controlled cooling Fan TR-40 (optional) Table 12. SP-4000 for Output 100/110/115/120 VAC specification. Note O Voltage range : Please refer to Figure 1 @ Normal load Condition : Vin =25V/50V, VAC 800/0 Full load (PF=I.O) O Operating temperature : Please refer to Figure 2 21 ****** Page 25 ****** 2-3-13. 22 Voltage & temperature performance 200% 115% 100% 0% 200% 115% 100% 40% 1 Min Continue 10.5V 21V 42V 1 Sec 16V 32V 64V 16.5V 33V Voltage (V) SP700-4000 Power / Voltage Curve Figure 1. Output power vs. input voltage 1 Sec Min Continue Output Power -200c ooc 400c 600c Temperature (DC) SP700-4000 Power / Temperature Curve Figure 2. Output power vs. temperature ****** Page 26 ****** 2-4. Mechanical Drawings AC Output Side Incun SP.7WIOOO Figure 3. 450-XXXX-X Series drawing (Top View) ooocoo 000000 100 Figure 4. 450-XXXX-X Series drawing (AC output/Front View) AC SO DC Input Sitie Model 450-0700-0 SP-IOOO SP-1500 SP-2000 SP-3000 SP-4000 A (mm) 330 372 421 443 442 462 B (mm) 80 69 92 103 103 113 C (mm) 132 196 196 196 196 196 D (mm) 200 200 248 248 255 255 E (mm) 7.0 7.0 7.0 7.0 7.0 7.0 Table 13. 450-XXXX-X Series Dimension F (mm) 83 83 83 83 158 158 23 ****** Page 27 ****** 3. Installation and Maintenance 3-1. AC Output Side (Front Panel) Introduction Figure 5. 450-0700-0/450-1000-0 AC output panel view o QOOOOOJ 000000B @ coo ooo Figure 6. 450-1500-0/450-2000-0 AC output panel view Figure 7. 450-3000-0/450-4000-0 AC output panel view 450-0700-0 450-1000-0 450-1500-0 450-2000-0 450-3000-0 450-4000-0 Model 24 Saving power adjustment Function switch Function LED TRC port (RJ45) Main switch AC output socket AC output terminal Table 14. 450-XXXX-X Series AC output side introduction ****** Page 28 ****** 3-1-1. Main Switch The 3-stage switch E is for turning on, turning off and remote mode. 3-1-2. LED Indicator 3-1-2-1. Input voltage level: to display Input Voltages LED status C Red Orange Green Orange Red DC 12V 15.5V DC 24V < 22.0V 22.0 23.OV 23.0 30.ov 30.0 31 .ov DC 48V 62.ov Table 15. Input Voltage Level LED Indicator 3-1-2-2. Output Load Level to display AC Loads (PF=I) LED status C 450-0700-0 SP-IOOO SP-1500 SP-2000 SP-3000 SP-4000 Green O 700 VA o – 1000 VA o & 1500 VA O 2000 VA O 3000 VA O 4000 VA Orange 700 805 VA 1000 1150 VA 1500 1725 VA 2000 2300 VA 3000 3450 VA 4000 4600 VA Red > 805 VA > 1150 VA > 1725 VA > 2300 VA > 3450 VA Table 16. Output Load Level LED Indicator 3-1-2-3. Inverter Status to display Fault condition LED status C Red Red Blink Red Fast Blink Status Normal Over Current Protection / Over Load Protection (AC output short and over load) Under Voltage Protection (Input DC voltage under spec) Over Voltage Protection (Input DC voltage over spec) Recovery point 12.5V @ DC12V system 25V @ DC24V system 50V @ DC48V system 14.5V @ DC12V system 29V @ DC24V system 58V @ DC48V system 25

****** Page 29 ****** LED status C Orange Orange Fast Blink Status Device startup Orange Blink Slow process abnormal Under Temperature Protection (Heat sink temp. under -20 degree) Over Temperature Protection (Heat sink temp. over 80 degree) Recovery point > 0 degree C < 60 degree C (heat sink temperature) Table 17. Inverter LED Status Indicator 3-1-3. Function Switch Introduction IJUUUUUU OFF Figure 8. DIP switch ON/OFF position 3-1-3-1. Function Switch Definition Dip Switch B Function Voltage select Voltage select Frequency Select Power saving ON/OFF Table 18. Function Switch Definition 3-1-3-2. Output voltage selection (Sl &S2) Output voltage 100V/200V 11 115V/230V 120V/240V OFF ON OFF ON OFF OFF ON ON Table 19. Function Switch definition: output voltage selection Note! 100V series can be selected between 100/110/115/120VAC, and 200V series can be selected between 200/220/230/240VAC. 26 ****** Page 30 ****** 3-1-3-3. Output Frequency Selection (S3) Frequency 50Hz 60Hz OFF ON Table 20. Function Switch definition: Output Frequency selection 3-1-3-4. Power Saving Selection (S4) Saving function Power Saving OFF Power Saving ON OFF ON Table 21. Function Switch definition: Power Saving selection 3-1-3-5. Power Saving Load Adjustment User can use variable resistor (VR) to set the input and wake up power saving threshold according to the load condition, and the setting range shows below: 450- 0700-0 450- 1000-0 450- 1500-0 450-2000-0 450- 3000-0 450-4000-0 -0700-0 450 450- 1000-0 450- 1500-0 450- 2000-0 450- 3000-0 450-4000-0 Input Saving Power Min VA VA VA VA VA Table 22. Power saving setting range (Min) Saving Wake up Power Min VA VA VA VA Input Saving Power Max <IIOVA <IIOVA <IIOVA <IIOVA <240 VA 160 VA >160 VA >160 VA > 160 VA >280 VA >280 VA Table 23. Power saving setting range (Max) 3-1-4. TRC Port (for optional kits TR-40, RJ-45) Pin Number 1 2 3 Reserved Signal Description D Zero-Crossing Signal Zero-Crossing Signal 27

****** Page 31 ****** Pin Number 4 5 6 7 8 TRC Bypass 12V GND Signal Description D Transfer Relay Driver Signal Internal power for TR40 controller Internal power for TR40 controller The same polarity as the battery negative side Reserved Table 24. 450-XXXX-X Series TRC Port : RJ-45. TR-40 Breaker Inverter TRC Input Output Input SP Series AC Output Load AC Figure 9. Wiring between 450-XXXX-X Series and TR-40 Note! The detail information. Please refer to T R-40 user manual. 3-1-5. AC output Interface 3-1-5-1. 450-0700/1000/1500/2000 AC output interface Socket Type F D North America (GFCI) Arnerica (GFCI) 28 NEMA 5-15R NEMA 5-20R Applicable Model 450-0700-0/450-1000-0 (100-120V) 450-1500-0/450-2000-0 (100-120V)

****** Page 32 ****** Socket Type F Australia I New Zealand ü8D Universal 0000 Hard Wire o France Connector UK Applicable Model 450-0700-0/1000/1500/2000/3000 212/224/248 450-0700-0/1000/1500/2000 (100-120V) 450-0700-0/1000/1500/2000/3000 (200-240V) 450-3000-0 450-4000-0 450-0700-0/1000/1500/2000/3000 (200-240V) Table 25. 450-XXXX-X Series AC Socket vs. Model 3-1-5-2. SP-3000/4000 AC output interface (É) Terminal Line (L) AC terminal Neutral (N) FG (Ground) Wire color Black White Green / Yellow or Bare copper Wire length I gauge Within 16 feet / AWG# 200-240VAC: AWGIO 100-120VAC: AWG8 26-32 feet / AWG# 10-8 Table 26. SP-3000/4000 Series AC output wiring 3-1-5-3. GFCI connector Recommend GFCI connector e HUBBELL INC WIRING DEVICE DIV, Type GF20. Rated 125/, 20A COOPER WIRING DEVICES, Type VGF20. Rated 125M 20A LEVITON MFG CO INC, Type 7899-W. Rated 125M 20A 29

****** Page 33 ****** 3-2. DC Input Side (Rear Panel) Introduction 101 Figure 10. 450-0700-0/450-1000-0 Figure 11. 450-1500-0/450-2000-0 Figure 12. 450-3000-0/450-4000-0 O Model 30 450-0700-0 450-1000-0 450-1500-0 450-2000-0 450-3000-0 450-4000-0 Remote port (RJII ) Remote control green terminal Chassis ground DC input connector Table 27. Series DC input side introduction

****** Page 34 ****** 3-2-1. Remote Port (RJ-11) The 450-XXXX-X Series Inverter can be compatible with CR-8, and CR-16 remote control via RS-232 Communication. Before using the remote control, make sure the main switch on inverter must be at ” REMOTE” position. Pin Number Signal Description 1 2 3 4 5 6 Reserved GND RXD TXD RMT vcc The same polarity as the battery negative side RS232 RXD RS232 TXD Remote controller panel (positive) Internal power for remote controller Table 28. 450-XXXX-X Series Remote Port : RI-II 3-2-2. Remote Control Green Terminal Remote control green terminal (2) may be connected to a Form C relay for “FAULT” indication. When “FAULT” occurs, the relay switches. Item 1 2 3 Description Dry contact (Normal Open) Common Dry contact (Normal Closed) Figure 13. Remote control terminal Item Description 4 5 6 Enable+ (ENB) Enable- (ENB) Ground Table 29. Dry contact terminal definition Note! Pin-6 is the same polarity with battery negative electrode. 31

****** Page 35 ****** I…Z..J Note! Fault conditions include Input under / over voltage, output short circuit / over load, over / under temperature. Caution! Please follow the following steps for the installation Before installing the inverter, make sure the main switch is at “OFF” position. e Before using the remote function, make sure the main switch pressed toward “REMOTE” Use 20 24 #AWG wire to connect the remote control terminals ENB ENB GND ON:INV. —ON OFF:INV. —OFF BAT* BAT. ON:INV. —ON OFF:INV. —OFF ENB GND HI:INV. —ON ITR ONI LOW:INV. —OFF ITR OFFI ON:INV. —ON OFF:INV. —OFF ENB POWER GND Figure 14. Wiring for control 3-2-3. General instruction before DC Input (4) 3-2-3-1 Before installation: The DC cables should be as short as possible (less than 6 feet / 1.8 meters ideally) The size of the cable should be thick enough to limit the voltage drop to less than 2% when carrying the maximum input current to prevent frequent low-input voltage warnings, and shutdown. The following sizes of cables and fuses are recommended for up to 6 ft. distance between the batteries and the inverter. 32

****** Page 36 ****** Model 450-0700-0 Inquire (700W, 24vDC) Inquire (700W, 48vDC) 450-1000-0 Inquire (1000W, 24vDC) Inquire (1000W, 48vDC) 450-1500-0 Inquire (1500W, 24vDC) Inquire (150M, 48vDC) 450-2000-0 Inquire (2000W, 24vDC) Inquire (2000W, 48vDC) 450-3000-0 Inquire (3000W, 24vDC) Inquire (3000W, 48vDC) Inquire (4000W, 24vDC) Inquire (4000W, 48vDC) Wire AWG Inline fuse 2150A = 80 A -50 A 2 225A 125A -80A 2 350A = 175A > 90A 2 500A = 225A -150A = 700A – 350A > 175A 2 500A -275A Table 30. 450-XXXX-X Series Wiring Cable diameter and Inline Fuse Note! Batteries are capable of providing very large currents in case of short circuit. The fuse should be as close to the positive battery terminal as possible. Use Bussmann ANN series fuses (will also require Fuse Block 4164) or equivalent. 3-2-4. Chassis Ground O) Must be connected to earth ground prior to making any other connections to the equipment. 3-3. Maintenance Make sure that the fan vents are not blocked. Use a vacuum cleaner to remove any dust from the fan area When cleaning the case or front panel, use a soft, dry cloth, only. If the case or front panel is very dirty, use a neutral, non-abrasive detergent. Do not use alcohol or ammonia based solutions. Regular service, and relocation of the inverter, should be performed by a qualified service technician. Avoid spilling liquid on the inverter. 33

****** Page 37 ****** 4. 34 Operation 4-1. Connection the DC cable Connect DC input terminals to 12V / 24V /48V battery or other DC power source [ + ] is positive, [ – ] is negative. Reverse polarity connection can blow the internal fuse and may damage the inverter permanently. Figure 15. DC cable connection Warning! Make sure that all the DC connections are tight (torque to 9— 10 ft-lbs, 11.7 €— 13 Nm). Loose connections could result in overheating and can be a potential hazard. Warning! The recommended inline fuse should be installed as close to the battery positive terminal as possible failure to use a fuse on the “+” cable running between the inverter and battery may cause damage to the cable / inverter and will void warranty. Also, only use high quality copper wire and keep the cable length short which is a maximum of 3 – 6 feet.

****** Page 38 ****** Inline Fuse Battery Figure 16. Battery cabling 4-2. Connecting the input power O, the main switch Before making the DC input side connections @ must be at “OFF”. 4-3. Connecting the loads Calculate the total power consumption of the output load. Make sure that the total power consumption does not exceed the rated power. If the total power consumption over the rated power of the inverter, remove the non-critical: loads until the total power consumption is below the rated power. 4-4. Switch ON Inverter Set the power switch to the “ONI’ position C). The inverter will carry out self-diagnosis and, the LED’s will also appear various colors. Set the power switch to the “OFF” position G). The inverter stops and all the lights that are on will go off. 35

****** Page 39 ****** 4-5. Protection Mechanism Over Voltage (DC) Under Voltage Alarm Ilv ± o.3V 22V± o.3V 44V± 0.3V Under Voltage Model 12V 24V 48V Model 12V 24V 48V Shutdown 16.5V± 33V ± o.5V 66 ± IV Restart 14.5V± o.3V 29V ± o.5V 58V ± IV Shutdown 10.5V± o.3V 21V± -0.5/ 42V± IV Restart 12.5V± o.3V 25V ± o.5V 50 ± IV Table 31. Protection Mechanism Over temperature protection Shutdown 80 Restart 60 5. 36 Table 32. Over Temperature Protection Mechanism RS232 Communication and Operation 5-1. RS232 Port RS232 Port : Serial port monitoring and control through computer interface. 6 1 1 5 00000 o 0000 Combi unit Figure 17. 450-XXXX-X Series o Computer RS-232 cable Computer PIN Number 1 2 3 4 5 6 Description Not used GND TXD Remo Control vcc PIN Number Not used RXD TXD Not used GND Not used Description 1 2 3 4 5 6

****** Page 40 ****** 450-XXXX-X Series PIN Number Description Computer PIN Number Not used Not used Not used Description 7 8 9 Table 33. RS232 interface definition 5-2. RS232 Port Operating The following steps show the connection among inverter and computer. Stepl Connect the RS232 port to the 450-XXXX-X Series unit on the front panel Step 2 Run the computer communication program Step 3 Set the transmission protocol Byte structure: START-BIP – 8 BIT DATA-STOP BIT Baud rate: 4800 Step 4 Select the COM port and start the operation 5-3. Example of RS232 Port Operating 5-3-1. RS232 command format This unit uses high-level language commands starts with CR (ODH) and LF(OAH) as the end of the command, The system would interpret and execute the command only after these two characters are received. After the unit executes the command, it would send a response string to the computer The response string is as follows: CR LF: Command executed successfully ?> CR LF: Command error, not accepted ! > CR LF: Command correct but execution error (e.g. parameters out of range) 37

****** Page 41 ****** 5-3-2. Command format The following table shows the useful command to operate Format: VINV? 450-XXXX-X Series. Function Turn ON / OFF 450-XXXX-X Series Command and description Format : Power can be one of the following. : Power OFF “1” : Power ON Query Series Query Series Query Series the 450-XXXX-X output frequency the 450-XXXX-X output voltage the 450-XXXX-X output current Query the 450-XXXX-X Series status 38 Format: Format: Format: Bit BITO BITI BIT2 BIT3 BIT4 BIT5 BIT6 BIT7 BIT8 BIT9 Format: Bit BITO BITI FRQ? ERR? (0700-2000) Description O: No OLPL Protection 1: OLPL Protection O:No Sof Fail Protection 1 :SofFail Protection O:No Poff Protection 1 :Poff Protection 0:No UVP Protection 1 :UVP Protection 0:NoOVP Protection 1 :OVP Protection O:No OLPM Protection 1: OLPM Protection O:No OLPH Protection 1: OLPH Protection O:No OTP Protection 1: OTP Protection O:N0 IJTP Protection UT P Protection O•.N0 OOCP Protection 1: OOCP Protection ERR? (3000-4000) Description O: No ID Fail 1: ID Fail 0:No Sof Fail Protection 1 :SofFail Protection

****** Page 42 ****** Function Command and description O:N0 PLL Fail BIT2 I:PLL Fail 0:No Poff Protection BIT3 1 :Poff Protection 0:No Short Protection BIT4 1 :Short Protection O:No OOCP Protection BIT5 1: OOCP Protection O:NoOVP Protection BIT6 1 :OVP Protection 0:No I-JVP Protection BIT7 1 :IJVP Protection O.•No OTP Protection BIT8 1: OTP Protection 0:No UT P Protection BIT9 1: UT? Protection 0:No OLPL Protection BITIO 1: OLPL Protection 0:No OLPH Protection BITII 1: OLPH Protection Query the 450-XXXX-X Series Format: VBAT? DC input voltage of the battery Query the 450-XXXX-X Format: Pl NV? Series output power Reset default Format: *RST Format : FUNC Select the Setup Menus with the help of Function Codes Query the functions No Query the setting value of the function Set or adjust the value of the function Function code 1 2 3 4 5 Format: Format: Format: Setting Menu OVP setting OVP Recovery I-JVP Setting IJVP Recovery I-JV Alarm RS-232 Baud-rate FUNC? SETT? SETT Table 34. RS-232 interface command The following data shows the function code detail setting value. 39

****** Page 43 ****** 5-3-2-1. FUN O: OVP setting SETT 150 165 300 330 600 640 Default 16.5V 33.ov 64.ov Table 35. OVP setting 5-3-2-2. FUN 1 • OVP Recovery SETT 135 145 270 290 540 580 Default 14.5V 29.ov 58.ov Table 36. OVP recovery 5-3-2-3. FUN 2 : I-JVP setting SETT 105 115 210 – 230 420 460 5-3-2-4. I-JVP Recovery SETT 125 – 135 250 270 oo=1V 500 540 oo=1V 5-3-2-5. FUN 4 : UV Alarm SETT 105 115 210 230 420 460 oo=1V Default 10.5V 21 .ov 42.ov Table 37. UVP setting Default 12.5V 25.ov 50.ov Table 38. UVP recovery Default 10.5V 21 nv 42 ov Table 39. UV alarm Model 12 Volt 24 Volt 48 Volt Model 12 Volt 24 Volt 48 Volt Model 12 Volt 24 Volt 48 Volt Model 12 Volt 24 Volt 48 Volt Model 12 Volt 24 Volt 48 Volt 40

****** Page 44 ****** 5-3-2-6. FUN 5 : RS232 Baud rate SETT 1 2 3 4 Default 3 Table 40. RS-232 baud rate Model 600 1200 2400 4800 9600 Default 3 6. 5-3-2-7. FUN 6 : Retry time SETT 1 2 3 4 Table 41. retry time Information 6-1. Warning Warning! Do not open or disassemble the Inverter. Attempting to do so may cause risk of electrical shock or fire. 6-2. Warranty All products of Kussmaul Electronics are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 2 years from the date the equipment was shipped. Defective products should be returned to Kussmaul Electronics with shipping charges prepaid. Upon repair, products will be returned to customer with shipping charges paid Kussmaul Electronics shall have no liability for damages of any kind to associated equipment arising from the installation and/or use of the Kussmaul Electronics products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. 41


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.