KOBE CHX9136SQB-2 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download KOBE CHX9136SQB-2 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** KOBE Range Hoods Brillia Series CHX91 SQB-2 Series Model No.: CHX9130SQB-2 (30″) CHX9136SQB-2 (36″) INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

****** Page 2 ****** IMPORTANT READ THIS FIRST READ BEFORE INSTALL TAION 1. Carefully check all contents of package(s). 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEMS: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIALS. 2. Have your original invoice as proof of purchase and product serial number ready. 3. Contact your merchant for product replacement due to shipping damages, cosmetic damages or defects. 4. For all other issues, email customer.service@koberanqehoods.com. NO RETURN, NO REFUND, NO EXCHANGE IF: 1. PRODUCT HAS BEEN INSTALLED 2. KNOCK-OUT HOLES HAVE BEEN PUNCTURED 3. MISSING ORIGINAL PACKAGING MATERIAL AND/OR PARTS

****** Page 3 ****** [ENGLISH] SAVE THESE INSTRUCTIONS – READ CONTENTS AND IMPORTANCE SAFETY INSTRUCTIONS . COMPONENTS OF PACKAGE . INSTALLATION.. OPERATING INSTRUCTIONS MAINTENANCE SPECIFICATIONS MEASUREMENTS & DIAGRAMS . PARTS LIST CIRCUIT DIAGRAM . TROUBLE SHOOTING WARRANTY WARRANTY INFORMATION FORM . 1 3 4 .9 .10 11 .12 . 14 .15 .16 .17 .19 – READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING – ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES

****** Page 4 ****** IMPORTANGE SAFETY INSTRUCTIONS – PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION – WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, 1. 2. 3. OBSERVE THE FOLLOWING: Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities. Ducted fans must be vented to the outside. a. Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE PANEL. b. Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl spaces or garages. NOTE This warranty is void without an authorized agent’s receipt or if unit is damaged due to misuse, poor installation, improper use, mistreatment, negligence or any other circumstances beyond the control of KOBE authorized agents. Any repair carried out without the supervision of KOBE authorized agents automatically void the warranty. KOBE will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood. WARNING: TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE 1. 2. 3. 4. 5. 6. 7. 8. TOP GREASE FIRE: Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container. Always turn hood ON when cooking Use high setting on cooking range ONLY when necessary. Do not leave cooking range unattended when cooking. Always use cookware and utensils appropriate for the type and amount of food prepared. Use this unit only in the manner intended by the manufacturer. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent power from switching on accidentally. Clean ventilating fan frequently. 1

****** Page 5 ****** What to Do in the Event of a Range Top Grease Fire 1. 2. 3. 4. SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. NEVER PICK UP A BURNING PAN – You May Get Burned. DO NOT USE WATER, including wet dishcloths or towels — a steam blast will result. Use an extinguisher ONLY if: a. You have a Class A, B, C extinguisher and know how to operate it. b. The fire is small and contained in the area where it started. c. The fire department has been called. d. You can fight the fire with your back to an exit. What to Do If You Smell Gas 1. Extinguish any open flame. 2. Do not try to turn on the lights or any type of appliance. 3. Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1. 2. 3. 4. 5. For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities. Activating any switch on may cause ignition or an explosion. Due to the size and weight of this hood, installation by 2 persons is recommended. A WARNING ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnected appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and Federal Codes. 2

****** Page 6 ****** COMPONENTS OF PACKAGE (Must keep all materials for returns or refunds) Range Hood Box {C} {G} W} {A} {D} KOBE Range Hood Warranty Registration Card Quick Reference Guide 6″ Round Vent Exhaust (Pre-lnstalled) 3-1/4″ x 10″ Exhaust Top Vent Cover with Rectangular Opening Top Vent Cover (to block Round Exhaust) Oil Tunnel x 1 Baffle Filters x 2 Stainless Steel Spacers x 2 Screws {B} {H} {C} Duct Cover Box (For Wall Mount Application Models Only) {L} Adjust Duct Cover {M} Duct Cover-Mounting Bracket {N} Duct Cover Support x 2 {O} Hood-Mounting Bracket {P} Screws Inner Duct Cover Outer Duct Cover {M} {O} QTY: 6 Size: QTY: 5 Size: 4*35 QTY: 8 Size: 4*12 FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE koberanqehoods.com OR CONTACT KOBE RANGE HOODS AT 626-775-8880. 3

****** Page 7 ****** INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1 and TABLE 2. (All calculation in inches). – FOR UNDER THE CABINET – TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36″) C = Preferred Height of Counter Top to Hood Bottom (Minimum 26″ to 30″) D = Height of hood E = Height of the Cabinet Cabinet Hood c 1 – FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) TABLE 2 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36″) C = Preferred Height of Counter Top to Hood Bottom (Minimum 26″ to 30″) D = Height of Hood E = Height of Duct Cover [F D] F = Height of the Hood Installation SAFETY WARNING 1 Hood c HOOD MAY HAVE SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING, OR SERVICING. BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER DAMAGE TO THE HOOD MAY OCCUR. USING HAND TOOLS IS RECOMMENDED. DO NOT OVER TIGHTEN SCREWS. MAKE SURE TO PREVENT ANY DEBRIS FROM ENTERING THE VENT OPENING TO AVOID DAMAGE OR MALFUCTION. 4

****** Page 8 ****** UNDER CABINET INSTALLA TION Before Installation 1. Read any provided document(s). 2. Test the range hood by temporarily connecting it to an outlet and turning ON the fan and lights. 3. If you run into any problems, contact KOBE Range Hoods. Venting Options and Requirements 4. 5. 6. 7. 8. 9. The range hood has 3 exhaust options: Top 6″ Round, Top 3-1/4″ x 10″ Rectangular, and Rear 3-1/4″ x 10″ Rectangular. The range hood is factory set for vertical or horizontal venting using round or rectangular vent adapter. Decide the location of the venting pipe from the hood to the outside. A straight, short vent run will allow the hood to perform more efficiently. Try to avoid elbows, transitions O O ‘ *Note: 6″ Round Vent Exhaust is pre-installed and long run as much as possible as this may reduce the on the range hood. performance of the hood. Make sure that the duct work leads to the outside. It is recommended to use metal/aluminum duct/pipe with a uniform size (ex. 6″ round pipe from range hood to the outside). If an elbow is necessary, a minimum of 12″ straight run is necessary before the elbow. For Top 6″ Round vent installation: The 6″ Round vent is already attached. (Refer to Figure 1) For Top 3-1/4″ x 10″ Rectangular vent installation only: Remove attached 6″ Round vent and discard. Keep seven screws to install the rectangular vent. Align and secure Top Vent Cover with Rectangular Opening with one screw. Then align and secure 3-1/4″ x 10″ Rectangular with two screws. (Refer to Figure 2) Figure 1 Figure 2 Figure 3 o 10. For Rear 3-1/4″ x 10″ Rectangular vent installation only: Remove attached 6″ Round vent and discard. Keep seven screws to install the rectangular vent. Align and secure Top Vent Cover with seven screws to block the top exhaust (Figure 3). Remove the duct knockout from back of the hood. Keep the screws and discard the duct knockout. Then align and secure 3-1/4″ x 10″ Rectangular with two screws (Figure 4). Clearance 11. Clearance is the distance between the cooktop and the bottom of the range hood. The recommended minimum clearance for this model is 26″ and the maximum clearance is 30″ 12. It is important to install the hood at the recommended clearance. Installing too low could result in damage and/or fire hazard while installing too high may result in reduce performance and efficiently. 5

****** Page 9 ****** Hood Installation 13. Remove any protective film off the hood, if any. 14. For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side (Figure 5). 15. Create access opening for electrical plug or wires and hood exhaust under the cabinet. 16. Align the hood in the center of the cabinet. As an optional step, you may position a flat-surfaced object below the hood as a support. Alternatively, another person can temporarily hold the hood. 17. There are 4 installing holes on top of the hood. Attached four 4*35 screws through the installing holes from the bottom to the top. The best way is to do this in a diagonal pattern: front left screw first then back right screw or vice versa. Make sure all the screws are tightened and the hood is secured before releasing hold/support. 18. Optional step: There are additional 4 installing holes at the back of the hood. Attached four 4*35 screws through the installing holes from the front to the back. The best way is to do this in a diagonal pattern. Make sure all the screws are tightened and the hood is secured before releasing hold/support. Ductwork 19. Once the hood is attached to the cabinet, connect the pipe onto the hood exhaust and secure the joint with duct tape. Make sure that it is completely air tight. Electrical Wire 20. Connect the range hood to an outlet. Figure 4 Figure 5 21. If hardwired is desired, cut off the plug and connect three wires (black, white, green) to the outlet wires and cap with wire connections (not provided). Connect the wires according to color (ex. black to black). Finish 22. Before using, make sure that any accessories such as filters are properly installed where applicable. 23. Test the range hood to see if it is working properly. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 6

****** Page 10 ****** WALL MOUNT INSTALLA TION Before Installation 1. Read any provided document(s). 2. Test the range hood by temporarily connecting it to an outlet and turning ON the fan and lights. 3. If you run into any problems, contact KOBE Range Hoods. Venting Options and Requirements O O *Note: 6″ Round Vent Exhaust is pre- installed on the range hood. Figure 1 4. 5. 6. 7. 8. 9. The range hood has 3 exhaust options: Top 6″ Round, Top 3-1/4″ x 10″ Rectangular, and Rear 3-1/4″ x 10″ Rectangular. The range hood is factory set for vertical or horizontal venting using round or rectangular vent adapter. Decide the location of the venting pipe from the hood to the outside. A straight, short vent run will allow the hood to perform more efficiently. Try to avoid elbows, transitions, and long run as much as possible as this may reduce the performance of the hood. Make sure that the duct work leads to the outside. It is recommended to use metal/aluminum duct/pipe with a uniform size (ex. 6″ round pipe from range hood to the outside.). If an elbow is necessary, a minimum of 12″ straight run is necessary before the elbow. For Top 6″ Round vent installation: The 6″ Round vent is already installed. (Refer to Figure 1) For Top 3-1/4″ x 10″ Rectangular vent installation only: Remove attached 6″ Round vent and discard. Keep seven screws to install the rectangular vent. Align and secure Top Vent Cover with Rectangular Opening with one screw. Then align and secure 3- 1/4″ x 10″ Rectangular with two screws. (Refer to Figure 2) O o Figure 2 Figure 3 Figure 4 o 10. For Rear 3-1/4″ x 10″ Rectangular vent installation only: Remove attached 6″ Round vent and discard. Keep seven screws to install the rectangular vent. Align and secure Top Vent Cover with seven screws to block the top exhaust (Figure 3). Remove the duct knockout from back of the hood. Keep the screws and discard the duct knockout. Then align and secure 3-1/4″ x 10″ Rectangular with two screws (Figure 4). Clearance 1 1 . Clearance is the distance between the cooktop and the bottom of the range hood. The recommended minimum clearance for this model is 26″ and the maximum clearance is 30″. 12. It is important to install the hood at the recommended clearance. Installing too low could result in damage and/or fire hazard while installing too high may result in reduced performance and efficiently. Hood Installation 13. Secure hood-mounting bracket and two duct cover-mounting bracket support on top of the hood with eight 4* 12 screws. Refer to Figure 5. 7

****** Page 11 ****** 14. Using reference on TABLE 2 and measurements on page XX to mark the leveling point of the hood. Position three 4*35 screws on the wall, leaving 1/8″ away from the wall as shown in Figure 6. 15. Align hood-mounting bracket to the three screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 16. There are 4 installing holes at the back of the hood. Attached the four 4*35 screws through the installing holes from the front to the back. The best way is to do this in a diagonal pattern. Make sure all the screws are tightened and the hood is secured before releasing hold/support. Ductwork 17. Use steel pipe to connect the exhaust on the hood to the ductwork. Use duct tape to make all joints secure and air tight. Duct Cover Installation 18. Use reference E from TABLE 2 and measurements on page XX to mark the position of the duct cover- mounting bracket. 19. Secure the duct cover-mounting bracket to the wall with two 4*35 screws. Make sure all screws are tightened. NOTE: Inner duct cover will cover the duct cover-mounting bracket. Refer to Figure 7. 20. Slide the entire duct cover onto the hood. Secure the outer duct cover with four 4*8 screws to the duct cover support. Figure 8. 21. Slide the inner duct cover until it reaches to the duct cover- mounting bracket. Secure inner duct cover with two 4*8 screws to the duct cover-mounting bracket. Refer for Figure 9. Electrical Wire 22. Connect the range hood to an outlet. 23. If hardwired is desired, cut off the plug and connect three wires (black, white, green) to the outlet wires and cap with wire connectors (not provided). Connect the wires according to color (ex: black to black). Finish 24. Remove any protective film from the hood, if any. 25. Before using, make sure that any accessories such as filters are properly installed where applicable. 26. Test the range hood to see if it is working properly. RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 8 *Note: Sample image only. May not be actual model. Figure 5 Mounting Screws Figure 6 Figure 7 *Note: Sample image only. May not be actual model. Figure 8 Figure 9

****** Page 12 ****** OPERATING INSTRUCTIONS 3-Speed Mechanical Push Button ooo OFF Q L O power Control Speed Control O Light Control NOTE: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed. To operate the fan function Press button to choose from speed Q = QuietModeTM speed O o L = Low speed o H = High speed Press “OFF” to turn fan off To operate the liqht function Press the Light Control to turn lights on and off 9

****** Page 13 ****** MAINTENANCE For optimal performance, clean the range hood surface and filters regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. ** *Regular care will help preserve its fine appearance. 1. 2. 3. 4. 5. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. If hood looks smudged (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood. DO NOT allow deposits to accumulate or remain on the hood. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel or extended periods. Many of these compounds contain chemicals, which may be harmful to hood. Rinse with water after exposure and wipe dry with a clean lint free cloth. For Baffle Filter models only: to Clean Baffle Filter I Oil Tunnel CAUTION: DRAIN OIL FROM BAFFLE FILTERS, SPACERS & OIL TUNNEL REGULARLY TO PREVENT OVERFLOW. 1. Remove all the baffle filters, spacers and oil tunnel. 2. Using a sponge, wash with warm soapy water. Dry completely before returning into place. CAUTION: SHARP EDGES (NOTE: Baffle Filters are top rack dishwasher safe) 10

****** Page 14 ****** SPECIFICATIONS MODEL 1 SIZE COLOR CONSUMPTION / AMPERE VOLTAGE 1 Hz NUMBER OF BLOWER DESIGN BLOWER TYPE EXHAUST CONTROL LIGHT HOOD DIMENSION OPTIONAL ACCESSORIES HOOD WEIGHT (lbs) SPEED Air Capacity (cfm) Sone* (dB) CHX9130SQB-2 (30″) CHX9136SQB-2 (36″) Commercial Grade Stainless Steel 106W / 1.17A 110V / 60Hz 2 Seamless / Satin Finish Twin Vertical Turbine Impeller Top: 6″ Round 3-1/4″ x 10″ Rectangular Rear: 3-1/4″ x 10″ Rectangular Mechanical Push Button 3-watt LED Light x 2 CHX9130SQB-2 CHX9136SQB-2 29-3/4″ x 22″ x 9-1/16″ 35-3/4″ x 22″ x 9-1/16″ 1. 2. 30″ Stainless Steel Back Panel Model No.: SSP30 (30″ x 1/10″ x 32″) 36″ Stainless Steel Back Panel Model No.: SSP36 (36″ x 1/1 0″ x 32″) CHX9130SQB-2 (30″) CHX9136SQB-2 (36″) QuietModeTM 306 1.0 Net 45.0 lbs 50.0 lbs Low 428 2.2 Gross 54.0 lbs 59.0 lbs Hiqh 600 5.0 *One sone is equivalent to the sound of a refrigerator at 40 decibels. * *Specifications subject to change without notice. 11

****** Page 15 ****** MEASUREMENTS & DIAGRAMS ** *All inch measurements are converted from millimeters. Inch measurements are estimated. ***AII measurements in ( ) are millimeters. – FOR UNDER THE CABINET – MODEL NO.: CHX9130SQB-2 (30″) CHX9136SQB-2 (36″) 5-1/8″ (130 (306 q 60 36- (560) MODEL NO.. 1/16„ ($60) (560) – FOR WALL MOUNT (WITH OPTIONAL DUCT COVER – CHX9130SQB-WM-2 (30″) CHX9136SQB-WM-2 (36″) (560) 12 10-7/16″ 265) (766) (908)

****** Page 16 ****** ** *Hood-Mounting Bracket 9-7/16″ (240) 3-1/2″ (90) 3-1/2″ (90) o o o o 13/16″ (21) 9/16″ (14) 13 1-3/8″ (35) 3/4″ (18) ** *Duct Cover-Mounting Bracket ** *Duct Cover Support 5-5116″ (295)

****** Page 17 ****** PARTS LIST MODEL NO.: CHX9130SQB-2 (30″) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 CHX9136SQB-2 (36″) DESCRIPTION 6″ Round Exhaust Plate 3-1/4″ x 10″ Rectangular Exhaust 3-1/4″ x 10″ Top Vent Cover Control Switch LED Li ht Ca acitor 5uF x 2 Metal Oil Tunnel Left Motor Right Motor Left Impeller Ri ht 1m eller S acer 33mm x 365mm Baffle Filter 322mm x 365mm Duct Cover (For Wall Mount Only) NO. 14 15 16 DESCRIPTION Duct Cover Duct Cover-Support Bracket Hood-Mounting Bracket 2 9 7 11 MODEL 1 SIZE PART NO. 02-030 02-031 02-032 02-006 02-005 02-033 02-034 02-035A 02-035B 02-036A 02-036B 02-038 02-037 MODEL 1 SIZE PART NO. 02-039 02-040 14 15 Duct Cover Box 121 13

****** Page 18 ****** CIRCUIT DIAGRAM MODEL NO.: CHX9130SQB-2 (30″) CHX9136SQB-2 (36″) Spot Black .4 2M 15

****** Page 19 ****** TROUBLE SHOOTING Issue After installation, both motors and lights are not working. Lights are working, but motor(s) is not. The range hood is vibrating The motor is working, but the lights are not working. The range hood is not venting out correctly. Cold air is coming into the home. Possible Cause The power is not on. The wire connection is not secure. The control anel is defective. The motor s is defective. The ca acitor s is defective. The control anel is defective. The blower system is not secure. The turbine impeller/squirrel cage is not balanced. Hood is not secured in place. LED li ht fixture s is defective. The light wiring(s) is loose. The control panel or LED light driver is defective. The range hood is installed outside of the manufacture recommended clearance. There is no make-up air inside the house. Obstacle blocking the pipe work. The pipe size is smaller than the suggested pipe size. The pipe connection is not properly sealed. The damper is not properly installed or is missing from the installation. The damper is not installed 16 Solution Make sure the circuit breaker and the unit’s power is ON. Use a voltage meter to check the power supply. Check and tighten wire connection. Re lace the control anel. Re lace the motor s Re lace the ca acitor s Re lace the control anel. Tighten the turbine impeller/squirrel ca e and air chamber. Replace the turbine im eller/s uirrel ca e. Check the installation of hood, ti hten the mountin bracket. Re lace LED li ht fixture s . Check wire continuity from control panel to LED light driver to LED light fixture s . Replace the control panel or LED li ht driver. Adjust the clearance between the range hood and cook top to 26″ to 30″. For island range hood, the distance between range hood and cook top is 30″ to 36″ Open the window to enhance the performance of the range hood by creatin a sufficient make-u air. Remove all obstacles from the duct work Change the ducting according to the manufacturer suggestion. Check the pipe from installation. Check the damper installation. Installing the damper will help eliminate air backflow.

****** Page 20 ****** WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Dealer. Please keep a copy of your original invoice as proof of purchase. ONE-YEAR LIMITED LABOR WARRANTY ON KOBE BRILLIA SERIES: For one year from the date of your original invoice from KOBE authorized dealer, we will repair any parts or components free of charge that failed due to manufacturing defects. KOBE reserves the right to replace, rather than repair the product free of charge at our sole discretion. It is your responsibility to ensure the product is readily accessible for the service technician to perform repairs. The service technician will not, under any circumstances, remove, alter or modify any fixture built around and/or connected to the product to gain access to perform repairs. TWO-YEAR LIMITED PARTS WARRANTY ON KOBE BRILLIA SERIES: For two years from the date of your original invoice from a KOBE authorized dealer, we will provide non-consumable replacement parts or components free of charge that failed due to manufacturing defects. Consumable parts such as light bulbs, fuses, and oil cups are not covered by this warranty. WHAT IS COVERED: This warranty is valid in the United States and Canada. It is non-transferable and applies only to the original purchaser and does not extend to any subsequent owners of this product. In Hawaii, Alaska, and Canada, this warranty is limited. There may be additional shipping charges for parts and service technician travel costs in remote areas or locations 30 miles outside of KOBE authorized service areas. WHAT IS NOT COVERED: 1. 2. 3. 4. 5. 6. 7. Normal wear and tear, regular service and maintenance required for the product. Consumable parts such as light bulbs, filters, fuses, and oil cups. Chips, scratches, or dents due to abuse or misuse of the product, use of corrosive and abrasive cleaning products. Damages caused by accident, fire, flood and other Acts of God. Services in remote areas or locations 30 miles outside of KOBE authorized service areas. Labor cost incurred in connection with the removal of range hood, and installation of replacement range hood, nor does it cover any other contingent expenses. Scratches inside the hood, back of the baffle filter, and inside the duct cover.

****** Page 21 ****** THIS WARRANTY WILL BE VOIDED BY: 1. 2. 3. 4. 5. 6. 7. Improper installation and failure to follow installation instructions. Any repair, alternation, modification not authorized by KOBE. Duct alternation, modification, and connection. Incorrect electric current, voltage, or wiring. Improper usage of the product such as commercial, outdoor, or other usage other than residential indoor usage. Purchasing this product from an unauthorized KOBE dealer. Damaging the product due to negligence, misuse, abuse, or accident. If we determine that the warranty exclusions listed above applies or if you fail to provide all necessary documentation for warranty service, you will be responsible for all expenses associated with the requested service, including parts, labor, shipping, traveling, and any other expense related to the service request. TO REQUEST WARRANTY SERVICE, PLEASE CONTACT KOBE RANGE HOODS SERVICE CENTER: From the 48 contiguous states: Email (best): customer.service@koberangehoods.com Phone: 1-626-775-8880 Toll Free: 1-877-BUY-KOBE (289-5623) From Alaska, Hawaii, and Canada: Email (best): customer-service@koberanqehoods.com Phone: 1-626-775-8880 18

****** Page 22 ****** WARRANTY INFORMATION FORM Fills in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase 2. Model No. 3. Serial No. For warranty service or spare parts purchase in US, contact: KOBE Service Center Email (best): customer.service@koberangehoods.com Phone: 1-626-775-8880 Toll Free: 1-877-BUY-KOBE (289-5623) For warranty service or spare parts purchase in Canada, contact: Email (best): customer.service@koberangehoods.com Phone: 1-626-775-8880 19

****** Page 23 ****** KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux Etats-Unis et au Canada seulement. II n’est pas recommandé d’utiliser cette hotte å l’étranger puisque l’alimentation électrique pourrait ne pas étre compatible et enfreindre le code de l’électricité de ce pays. L’usage de la hotte KOBE l’étranger est votre propre risque et la garantie sera annulée. Esta campana de extracciön KOBE ha Sido fabricada para ser utilizada ünicamente en EE.UU. y CANADA. No recomendamos la utilizaciön de esta campana en el extranjero debido a que la fuente de energia podria no ser compatible y podria violar el cödigo eléctrico de dicho pais. Utilizar una campana KOBE en el extranjero serå a su propio riesgo y anularå la garantia. VER. 211101 Information subject to change without notice.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.