KLIK KCMPH2DL (01) PDF Document

It is recommended to use the KLIK KCMPH2DL multiport adapter with your computer’s power supply connected to the USB-C Power Port. This will provide power to the multiport adapter while also providing power to charge your computer.

First, connect the multiport adapter to your computer by plugging the built-in USB-C male cable into a USB-C port on your computer. Then, connect your computer’s power supply to the USB-C Power Port on the adapter. This adapter supports up to 100W of power pass through.

For older laptops without a USB-C port, you can use the included USB-C to USB-A adapter to connect the adapter to a USB-A port on your computer. Please note that this must be a 5Gbps USB 3.0 port, and power pass through is not supported when using a computer’s USB-A port.

You can connect one or two external monitors to the two HDMI ports on the KLIK KCMPH2DL. This multiport adapter uses DisplayLink technology for universal monitor support for macOS, Windows, and ChromeOS.

For Windows and ChromeOS users, the DisplayLink drivers are built-in, and the monitors should automatically start working after a short time.

For macOS users, you will need to install the DisplayLink drivers manually.

The maximum resolution supported is 1920 x 1080 @60Hz. You can run dual monitors in either mirror or extended mode.

You can connect your USB-A and USB-C devices to the USB-A and USB-C data ports on the KLIK KCMPH2DL. This includes peripherals such as a keyboard, mouse, USB flash drives, external storage devices, webcams, or other USB devices. The maximum data transfer rate for these ports is 5Gbps.

Yes, you can use the USB-A and USB-C ports on the KLIK KCMPH2DL to charge your phone or other devices. The maximum power output of each USB port is 5V/1.5A (7.5W). The maximum total output of all USB ports is 13.5W shared.

To charge a phone or a large external storage device that consumes a large amount of power, the laptop’s power supply must be connected to the multiport adapter’s USB-C Power Port.

To connect to a wired network, plug an Ethernet network cable into the RJ45 Gigabit LAN port on the KLIK KCMPH2DL. This will connect your computer to the wired Ethernet network. The green LED on the port indicates a successful connection to a network, and the yellow LED indicates network activity.

The KLIK KCMPH2DL requires DisplayLink drivers to be installed on macOS to support external monitors. Windows and ChromeOS have native support and do not require additional drivers. Follow these steps to install the drivers on macOS (MacOS X 10.8 onwards):

1. Visit http://www.synaptics.com/products/displaylink-graphics and select macOS from the Latest DisplayLink Drivers list.

2. Download the latest version of “DisplayLink Manager”.

3. After clicking “Download” and accepting the License, double-click the downloaded file and run the DisplayLink Installer Wizard.

4. Follow the on-screen instructions to complete the installation.

5. Make sure your external monitors are connected to the multiport adapter via an HDMI cable.

6. From the Notification Center (normally top right on your Mac), start the DisplayLink Manager for the first time by clicking its icon. The DisplayLink Manager can also be found in the Applications folder.

7. When you run the DisplayLink manager for the first time, a “Screen Recording” permission box will appear. This is a necessary function for DisplayLink. To proceed, click “Open System Preferences”.

8. In the “Security & Privacy” window, navigate to the Privacy tab and select “Screen Recording” from the list on the left. If the lock in the bottom left corner is locked, click it to unlock. Then, check the box next to the DisplayLink Manager to enable Screen Recording.

9. A message will appear stating that “DisplayLink Manager” will not be able to record the contents of your screen until it is quit. Click the “Quit & Reopen” button. Your external monitors should now start working.

10. To make DisplayLink run automatically at startup, open the DisplayLink Manager app from the Notification Centre or Application folder and check the “Automatic startup” box.

• Connect two monitors, a keyboard & mouse, Gigabit LAN, USB storage devices & other USB devices all via a single USB-C connection.

• DisplayLink technology supports dual monitors in mirror or extended desktop mode for macOS, Windows and ChromeOS, including MacBooks with M1, M2 or Intel chips.

• Supports dual monitors at full HD 1920 x 1080 @60Hz.

• 2 x HDMI monitor ports.

• 1 x RJ45 Gigabit LAN Port.

• 2 x USB-A 3.0 data ports (5Gbps).

• 1 x USB-C 3.1 data port (5Gbps).

• 1 x USB-C female port for up to 100W of power pass through.

• 1 x USB-C male to connect to host computer.

• 1 x USB-C to USB-A Adapter.

• Dimensions: 122 x 68 x 17mm.

• Weight: 110g (116g if using USB-C to USB-A Adapter).