Free English KIDDE P4010ACSCO-W (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD KIDDE P4010ACSCO-W (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the primary features of the KIDDE P4010ACSCO-W?
The KIDDE P4010ACSCO-W includes the following features:
- 120V Hardwire power source.
- 10-year sealed-in battery backup (non-replaceable).
- Hardwire and Wire-free Interconnect capabilities.
- Voice Alarm system.
- Combination Photoelectric Smoke & Carbon Monoxide detection.
- Ambient Light Sensing.
- SMART HUSH Control to silence nuisance alarms.
What should I do when the smoke alarm sounds on the KIDDE P4010ACSCO-W?
The smoke alarm pattern is three long beeps with the voice “Fire!”, a 1.5-second pause, and three long beeps repeating. The red LED blinks in time with the alarm pattern. If this occurs:
1. Alert small children and anyone needing assistance.
2. Leave immediately by your escape plan. Do not waste time dressing or collecting valuables.
3. Feel doors before opening. If hot, use an alternate exit. If cool, open cautiously.
4. If escaping through smoke, stay close to the floor and breathe shallowly through a cloth.
5. Once outside, go to your meeting place and call the fire department from outside.
6. Do not return inside until officials say it is safe.
What is the Carbon Monoxide alarm pattern and procedure for the KIDDE P4010ACSCO-W?
The CO alarm pattern is four quick beeps with the voice “Warning! Carbon Monoxide” repeating every 5 seconds. The red LED blinks in time with the alarm pattern. If this occurs:
1. Operate the Test/Hush button. If the unit alarms again within six minutes, high levels of CO are present.
2. Call emergency services (Fire Department or 911).
3. Immediately move to fresh air outdoors or by an open door/window.
4. Do a head count to ensure all persons are accounted for.
5. Do not reenter the premises until emergency responders arrive and the alarm remains in its normal condition.
What do the visual and audible indicators mean on the KIDDE P4010ACSCO-W?
| Operational Mode | Visual Indications | Audible Indications | Action/Note |
|---|---|---|---|
| Normal (standby) | AC power: Green LED on continuously during light conditions, or blink every 60 sec during dark conditions. DC power: Green LED blink approx every 60 sec. | None | None |
| Test (button press) | 4 patterns of Red/Amber/Green. Test: Red LED blinks in time with alarm pattern. Green LED fade on/off at test complete. | Button press sound. Voice: “Testing…” 3 long beeps, Voice “Fire!”, 3 long beeps, 4 quick beeps, Voice “Warning, Carbon Monoxide,” 4 quick beeps, Voice “Test Complete,” Power on/reset sound. | Perform Test/Hush button press once a week to verify proper alarm operation. Push/release button before the countdown ends to cancel test. |
| Smoke or CO Alarm Memory | Red and Amber LED alternate on 1 sec, every 10 sec. | After button push: “Smoke previously detected” or “Carbon Monoxide previously detected” only on the initiating alarm unit. | Push test button to clear Alarm Memory. Standard test sequence will follow. |
| Smoke Alarm Hush Mode | Red LED blinks every 2 sec. | After button push: “Hush Mode Activated.” Smoke alarm pattern stops. | This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. |
| CO alarm reset | None | After button push: CO alarm pattern stops. | Unit is confirming if CO is present or if it experienced a nuisance situation. Re-alarm means danger. |
| Locate | None | After button push on non-initiating unit, only initiating unit continues alarm pattern. | Use this to quickly locate the alarm source and determine if alarm is nuisance or real. |
| Smoke Alarm Hush Mode Canceled | None | Voice message “Hush Mode Canceled.” | When smoke levels drop below the alarm threshold, the voice message “Hush Mode Canceled” will occur. |
| Initiating Alarm (Interconnected) | Green LED blinks once per sec. | Unit in either Smoke or CO alarm mode. | During alarm, the initiating alarm red blink will be interrupted by a green blink. |
How do I troubleshoot error conditions on the KIDDE P4010ACSCO-W?
| Trouble Condition | Visual Indications | Audible Indications | Action |
|---|---|---|---|
| Low Battery | Amber LED blinks every 5 seconds | Chirp every 60 sec, voice every 30 sec: “Replace alarm.” Voice stops after 5 mins. | Remove, discharge, dispose unit, and replace as soon as possible. |
| Fault Mode | Amber LED blinks every 5 seconds | Chirp every 30 sec. Voice every 30 sec: “Error, see trouble shooting guide”. After 5 mins: no voice message. | See Cleaning Your Alarm section. Push Test/Hush button once to attempt to reset. If red LED blinks an error code, report number of blinks to customer service. |
| End of Unit Life | Amber LED blinks every 5 seconds | Double chirp every 30 sec. First 5 mins: Voice every 30 sec: “Replace alarm…”. After 5 mins, voice stops but chirps continue. | Push/release Test/Hush button to temporarily silence (for 24 hours). Remove, discharge, dispose unit, and replace as soon as possible. |
| Network Error | Amber LED blinks every 5 seconds | Chime every 30 secs. Voice every 30 sec: “Connection lost, press button to temporarily silence.” | See Network Error troubleshooting tips. Note: network must have 3 or more alarms for voice messages. |
How do I fix a Network Error on the KIDDE P4010ACSCO-W?
If you have a unit in network error, try the following fixes:
Fix 1:
1. Rotate the alarm on the mounting plate 90 degrees to re-orient the antenna.
2. Press and hold the button on a known working unit for 4-5 seconds until you hear 2 beeps.
3. Go to the unit in network error. Press and hold the button for 4-5 seconds until you hear 2 beeps.
4. Within 10 seconds, the error unit should re-join the network, show fading green lights, and announce “Success, now connected.”
5. If successful, press and hold the button on the same unit for 4-5 seconds until 2 beeps are heard to close the network.
Fix 2:
1. Go to a wireless unit closest to the center of the house.
2. Press and hold the button on that unit for 4-5 seconds until you hear 2 beeps and “Searching for other devices.”
3. Locate the Coordinator (fading green on/off every 2 seconds). Move the Coordinator to the center of the house.
4. Go to each unit in error and press/hold the button for 4-5 seconds until you hear 2 beeps. They should announce “Success, now connected.”
Fix 3:
1. Take all wireless units down.
2. Reset all units one by one by pressing and holding the button for 8-9 seconds until you hear 3 beeps and “Resetting wireless settings.”
3. Create a new network by pressing and holding the button on one unit for 4-5 seconds until 2 beeps (this becomes the Coordinator).
4. Wait for other units to join. After all have joined, press/hold button on Coordinator for 4-5 seconds.
5. Install the Coordinator closest to the center of the household.
How do I set up a wireless alarm network for the KIDDE P4010ACSCO-W?
A. Power Up: Turn the red wheel on the back of all devices to the “ON” position. Light rings will glow red and announce “Ready to connect.”
B. Pick One Device (Coordinator): Choose one unit to be the Coordinator. Press and hold the button on ONLY this unit until you hear two beeps. Release the button. It will announce “Searching for other devices” and emit a sonar ping.
C. Wait for Connection: Wait until all other devices (RFDs) connect. Once connected, each device will speak “Success now connected!” and lights will glow green.
D. Close Network: Press and hold the button on the Coordinator device for 5 seconds until you hear two beeps. The sonar ping will stop, and the device will announce setup is complete.
How do I add another device to an existing wireless alarm network on the KIDDE P4010ACSCO-W?
1. Power up the new device by turning the red wheel to “ON.”
2. Press and hold the button on ONE INSTALLED device on your network until you hear two beeps. Release the button. It will announce “Searching for other devices” and ping.
3. Wait for the new device to connect and announce “Success now connected!”
4. Press and hold the button on the INSTALLED device for 5 seconds until you hear two beeps to stop the ping and complete setup.
How do I reset the wireless settings on the KIDDE P4010ACSCO-W?
1. Press and hold the button on the device for 8-9 seconds until you hear 3 beeps.
2. Release the button. You will hear the words “Resetting wireless settings.”
3. The light ring will flash green once and then pulse red, followed by the words “Ready to connect, follow quick start instructions.”
What are the wiring requirements for the KIDDE P4010ACSCO-W?
The alarm should be installed on a UL Listed junction box using 120 Volt AC Single Phase power from a non-switchable circuit. A maximum of 24 Kidde Safety devices may be interconnected. The maximum wire run distance is 1000 feet.
Wiring Colors:
- Black: Hot side of AC line
- White: Neutral side of AC line
- Red: Interconnect lines (red wires) of other units in the multiple station set-up. (Leave the insulating cap on if not hardwire interconnecting).
How do I test the KIDDE P4010ACSCO-W?
Test the alarm weekly by pressing and releasing the test button quickly. A quick beep will confirm the button has been pushed, followed by voice prompts. The alarm and voice (and any interconnected units) will sound. Always stand about 2.5 feet away from the unit or use ear protection when testing.
How does the Ambient Light Sensing work on the KIDDE P4010ACSCO-W?
This unit samples ambient light conditions to determine a Night/Day cycle. A valid Night/Day cycle will delay End of Unit Life or Network Error chirps during the night until the next Day cycle begins. Low Battery chirps cannot be silenced or delayed.
How do I clean the KIDDE P4010ACSCO-W?
You should clean the alarm at least once a year:
1. Use compressed air or a vacuum cleaner hose to blow or vacuum through the openings around the perimeter of the alarm.
2. Wipe the outside of the alarm with a damp cloth. Use only water; do not use detergents or cleaners.
3. Do not attempt to disassemble the unit.
How do I permanently disable and discharge the battery on the KIDDE P4010ACSCO-W?
The battery is sealed and non-replaceable. To permanently disable for disposal:
1. Rotate the alarm counterclockwise to remove it from the mounting plate.
2. Disconnect the AC wiring harness.
3. Push in the dashed area labeled “Break tab” with a screwdriver to break the tab.
4. Use the screwdriver to turn the red slotted arrow to the “Permanently Disable Alarm / Discharge Battery” location.
Note: This will disable the alarm, stop chirps, and render the alarm safe for disposal. It cannot be reactivated.
CLICK HERE TO DOWNLOAD KIDDE P4010ACSCO-W (01) PDF DOCUMENT