KAWAI CN39 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD KAWAI CN39 (01) PDF MANUAL


PDF Content Summary: CN39 Owner’s Manual Introduction Playing the Piano Music Menu Recorder Settings Appendix Thank you for purchasing this Kawai CN39 digital piano. This owner’s manual contains important information regarding the instrument’s usage and operation. Please read all sections carefully, keeping this manual handy for future reference. ■ About this Owner’s Manual Before attempting to play this instrument, please read the Introduction section from page 10 of this owner’s manual. This section explains the name and function of each part, how to connect the power cable, and how to turn on the power. The Playing the Piano section (page 19) provides an overview of the instrument’s commonly used functions, allowing the CN39 digital piano to be enjoyed almost immediately after being connected, while the Music Menu section (page 38) includes information regarding the built-in demonstration songs, Piano Music pieces, Lesson and Finger Exercise features, and Concert Magic function. The Recorder section (page 50) provides instructions on how to record and play back pieces stored both in the instrument’s internal memory, and also MP3/WAV audio files saved to a USB memory device. The Settings section (page 68) details the various options and settings that can be used to adjust the sound and operation of the instrument. Finally, the Appendix section (page 131) includes lists for all internal sounds, songs, and drum rhythms, assembly instructions for the CN39 model, MIDI reference information, and full specification details. Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS CAUTION WARNING RISK OF DO ELECTRIC NOT OPEN SHOCK denotes that care should be taken. The example instructs the user to take care not to allow fingers to be trapped. denotes The example a prohibited instructs operation. that disassembly of the product is prohibited. denotes an operation that should be carried out. The example instructs the user to remove the power cord plug from the AC outlet. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prongs are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. AVIS : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of su cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the leterature accompanying the product. Examples of Picture Symbols Read all the instructions before using the product. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. [Seuls les produits avec 3P fiche] PRECAUTION Le symbole de l’éclair avec une pointe de flèche à l’intérieur d’un triangle équilatéral met en garde l’utilisateur contre la présence de tension dangereuse, non isolée, à l’intérieur de l’appareil, dont l’amplitude peut être suffisante pour induire un risque d’électrocution d’une personne. Exemples de symboles graphiques Faite attention de ne pas introduire un produit étranger à l’intérieur de l’appareil. Ce produit n’est pas totalement déconnecté du circuit électrique lorsqu’il est mis hors tension par le bouton d’arrêt. Si l’appareil ne doit pas être utilisé pendant une longue période, débranchez le câble d’alimentation de la prise secteur. Il est recommandé de placer l’instrument à proximité de la prise de courant et de positionner le câble d’alimentation secteur présent tant de sorte que la qu’il prise puisse est branchée être débranché même si rapidement le bouton de en mise cas en d’urgence, marche est le en courant position électrique Arrêt. étant toujours INSTRUCTIONS DE MISE À LA TERRE Ce produit doit être mis à la terre. En cas de défaillance matérielle ou de panne, la mise à la terre fournit un chemin de moindre résistance au courant électrique afin de réduire le risque d’électrocution. Ce produit est équipé d’un câble avec un conducteur de protection et une fiche de mise à la terre. La fiche doit être branchée dans une prise appropriée correctement installée et mise à la terre conformément à tous les codes et règlements locaux. DANGER - La connexion incorrecte du conducteur de protection peut présenter un risque d’électrocution. Consultez un électricien ou un réparateur qualifié si vous avez des doutes en ce qui concerne la mise à la terre du produit. Ne modifiez pas la fiche fournie avec le produit – si elle n’est pas adaptée à la prise, faites installer une prise correcte par un électricien qualifié. Si vous ne le faisiez pas la foudre pourrait provoquer un incendie. Si vous ne le faisiez pas, la surchauffe de l’appareil pourrait provoquer un incendie. Indique un risque potentiel qui peut entraîner la détérioration, ou des dommages, pour l’appareil ou ses propriétés, si celui-ci n’est pas manipulé correctement. Description de la l'emplacement de la reference (Le cas échéant): Anglais phrase: The nameplate label is located on the underside of the instruments, as indicated below. Français phrase: La reference commerciale est inscrite sur une etiquette en dessous de votre instrument, conformement a l’indication ci-dessous. Votre piano doit être placé à un endroit tel que sa position n’altère pas sa propre ventilation. Gardez une distance minimum de 5 cm autour de l’instrument pour une aération suffisante. Règles de sécurité (Supplémentairespour le Canada) CONSERVEZ CES INSTRUCTIONS CAUTION AVERTISSEMENT RISK OF DO ELECTRIC NOT OPEN SHOCK AVERTISSEMENT POUR REDUIRE LES RISQUES D’INCENDIE OU D’ELECTROCUTION, PROTEGEZ CET APPAREIL DE LA PLUIE OU DE L’HUMIDITE. AVIS : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR. POUR REDUIRE LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE DEMONTEZ PAS LE COUVERCLE (OU L’ARRIERE). A L’INTERIEUR, AUCUNE PARTIE N’EST REPARABLE PAR L’UTILISATEUR. POUR LA MAINTENANCE, ADRESSEZ-VOUS A DU PERSONNEL QUALIFIE. Le point d’exclamation à l’intérieur d’un triangle équilatéral alerte l’utilisateur de la présence de règles d’utilisation et d’entretien importantes dans la notice qui accompagne l’appareil. Indique que des précautions doivent être prises. L’exemple indique à l’utilisateur qu’il doit faire attention à ne pas se faire coincer les doigts. Indique une manipulation interdite. L’exemple indique que le démontage de l’appareil est interdit. Indique qu’une manipulation doit être effectuée. L’exemple indique à l’utilisateur qu’il doit débrancher le câble d’alimentation de la prise secteur. Indique un risque potentiel qui peut entraîner la mort, ou de graves lésions, si l’appareil n’est pas manipulé correctement. L’introduction d’eau, d’aiguilles ou d’épingles à cheveux, peut provoquer une panne ou un court-circuit. Ce produit doit être mis à l’abri des écoulements ou projections d’eau. Ne jamais placer sur le produit des objets contenant des liquides, tels que des vases ou autres récipients. WARNING - When using electric products, basic precautions should always be followed, including the following. WARNING Indicates a potential hazard that could result in death or serious injury if the product is handled incorrectly. The an AC product outlet should of the specified be connected voltage. to 120V 230V 240V x If you are going to use an AC power cord, x This product shall be near the AC outlet and the power cord plug in a position so that it can readily be disconnected in an emergency because electricity is always charging while the plug is in the AC outlet even in a power switch o condition. make and conforms sure that to its the has specified the correct power plug voltage. shape Failure to do so may result in fire. Do cord not plug insert with or wet disconnect hands. the power Doing so may cause electric shock. Take matter care to not enter to the allow product. any foreign Entry in breakdown of water, or needles short-circuit. or hair pins may result The splashing. product No shall objects not be filled exposed with liquids, to dripping such as or vases, shall be placed on the product. The chair must be used properly (it must be used only when playing the product). Doing fingers so to may be trapped, cause the resulting chair to in fall injury. over or your x Do not play with it or stand on it. x x x Do Only Re-tighten not one sit person on the it when bolts is allowed occasionally. opening to the sit on lid. it. When listen for using long the periods headphones, of do not Doing so may result in hearing problems. time at high volume levels. Do not lean against the keyboard. Doing so may cause the product to fall over, resulting in injury. Do the not product. disassemble, repair or modify Doing shock or so short-circuit. may result in product breakdown, electric When plug, always disconnecting hold the the plug AC power cord's and pull it to remove it. Pulling the AC power cord itself may damage the short-circuit. cord, causing a fire, electric shock or The product is not completely disconnected from the power o . If the supply product even will when not the be power used for switch a long is time, turned unplug the AC power cord from the AC outlet. x x Failure lightning. to do so may Failure resulting to in do fire. so may cause fire in case of over-heat the product, This product may be equipped with a polarized line plug (one blade wider than If you the are other). unable This to insert is a safety the plug feature. into the outlet, contact an electrician to replace your obsolete outlet. Do not defeat the safety purpose of the plug. Indicates CAUTION damage to a potential the product hazard or other that property could result if the in product injury or is handled incorrectly. Do not use the product in the following areas. x x x x x x exposed Areas, such to direct as those sunlight near windows, where the product is Extremely Extremely hot cold areas, areas, such such as as near outside a heater Using product the breakdown. product in such areas may result in Use in tropical the product climates). only in moderate climates (not Extremely Areas where humid a large areas amount of sand or dust is present Areas vibrations where the product is exposed to excessive When close it you gently. close the keyboard cover, Closing resulting it in roughly injury. may trap your fingers, Before connecting cords, make sure that and other the power devices to this is turned product OFF. OFF Failure to do so may cause breakdown of this product and other devices. Do Take not care drag not the to product drop the on product. the floor. Please Please lift note up that the the product product when is heavy moving and it. must be Dropping carried the by more product than may two result persons. in breakdown. Do appliances not place such the as product TVs and near radios. electrical x Doing so may cause the product to generate x If noise. product the product su ciently generates away noise, from move the electrical the appliance or connect it to another AC outlet. When connecting the AC power cord and not to other get cords, them tangled. take care Do candles not place on the naked product. flame, such as lighted Doing resulting so in may fire. cause the illumination to fall over, Ensure that the ventilation is not Failure to do so may over-heat the product, impeded openings by with covering items, such the ventilation as newspaper, resulting in fire. table-cloths, curtains, etc. The minimum product distance should of be 5cm located around so that the product its location for su or position cient ventilation. does not interfere with its proper ventilation. Ensure a Failure fire, electric to do shock so may or damage short-circuit. them, resulting in Do not wipe the product with benzene or thinner. x Doing of the product. so may result in discoloration or deformation x When lukewarm cleaning water, the squeeze product, it well, put a then soft wipe cloth the in product. Do excessive not stand force. on the product or exert Doing so may cause the product to become deformed or injury. or fall over, resulting in breakdown The product should be serviced by qualified service personnel when: x x x x x The The The The Objects product power product product have supply has does has fallen, been been not cord or appear exposed dropped, liquid or the has to plug to or operate been rain. the has enclosure spilled been normally damaged. into damaged. or the exhibits product. a marked change in performance. Notes Should contact on an the Repair abnormality shop from which occur the in the product product, was immediately purchased. turn the power OFF, disconnect the power cord plug, and then CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. ATTENTION: Pour pousser éviter jusqu'au les chocs fond. électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et An If separately You e For (European your ects information further should on product the by Union not details, environment taking mix is on marked only) it please Disposal with it to an general with contact and appropriate for human this household users your recycling health local collection waste. authority. which symbol could Disposing point. it means otherwise of that, this at arise product the due end correctly to of inappropriate its life, will you prevent must waste potential dispose handling. negative of it Instruction IMPORTANT THE WIRES IN for THIS AC MAINS power LEAD cord ARE COLOURED (U.K.) IN ACCORDANCE WITH THE FOLLOWING CODE. BLUE BROWN : : NEUTRAL LIVE As the The The Do the not terminals wire wire colours plug which which either in of is is your the coloured coloured terminal wires plug, proceed in BLUE BROWN of the the must mains power as must follows: be lead be cord connected of connected to this the apparatus to the the to ground the terminal may terminal od not AC which correspond which outlet is marked is on marked the with wall. with the with the coloured the letter letter N markings or L or coloured coloured identifying BLACK. RED. FCC Information (U.S.A) CAUTION authority to : Changes operate the or modifications equipment. not expressly approved by the party responsible for compliance could void the user’s NOTE the installation. accordance that television the FCC interference interference : This Rules. reception, This with equipment These equipment by the will one instructions, which limits not or has occur more are can been generates, designed in be of may tested a determined the particular cause following uses to and provide and harmful found installation. by can measures: turning reasonable to radiate interference comply If the this radio equipment with protection equipment frequency to the radio limits o against communications. does energy and for a cause on, harmful Class and, the harmful B user if digital interference not However, is installed interference encouraged device, there in pursuant and a residential is used to to no radio try guarantee to in to Part or correct 15 of x Reorient or relocate the receiving antenna. x x x Increase Connect Consult the the the dealer separation equipment or an between experienced into an outlet the equipment radio/TV on a circuit technician and di receiver. erent for from help. that to which the receiver is connected. Declaration of Conformity The the indicated underside nameplate below. of label the instrument, is located on as Products : Electronic Piano Model Responsible Number Party : Name : CN39 Kawai America Corporation Address : 2055 East University Drive Rancho Telephone Dominguez, 310-631-1771 CA 90220 This device complies with Part 15 of the FCC Rules. Operation (1) this device is subject may to not the cause following harmful two interference, conditions: and (2) this including device interference must accept that any may interference cause undesired received, operation. This applies only to products distributed by Kawai America Corporation. Nameplate About Bluetooth x The Inc. Other and Bluetooth® trademarks any use word of and such mark trade marks and names by logos Kawai are are those Musical registered of their Instruments trademarks respective Mfg. owned owners. Co., Ltd. by the is under Bluetooth license. SIG, x x Frequency Maximum Availability Transmit Band of Bluetooth of Radio: Power: function 2400~2483.5 2.5 mW dependent (Bluetooth MHz on Low market Energy), location. 4.5mW (A2DP) 8Table of Contents Important Safety Instructions ....................... 3 Table of Contents .................................... 8 Introduction Welcome to the Kawai CN39 digital piano . . . . . . . . . 10 1. Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2. Owner’s Manual Conventions . . . . . . . . . . . . . . . . . 11 Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Setting Up the Piano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1. Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2. Key cover and music rest . . . . . . . . . . . . . . . . . . . . . . 15 3. Volume and headphones . . . . . . . . . . . . . . . . . . . . . 16 4. Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Playing the Piano Selecting Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Dual Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Split Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Four Hands Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Virtual Technician . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 1. Smart Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2. Advanced Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Metronome / Drum Rhythms . . . . . . . . . . . . . . . . . . . . . . . 32 Registration Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 1. Selecting a Registration memory . . . . . . . . . . . . . 34 2. Storing a Registration memory . . . . . . . . . . . . . . . 35 3. Registration Edit menu . . . . . . . . . . . . . . . . . . . . . . . 36 Panel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Music Menu Demo Songs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Piano Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Lesson Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 1. Selecting a lesson book/song . . . . . . . . . . . . . . . . . 40 2. Listening to the selected lesson song . . . . . . . . . 41 3. Lesson Function settings . . . . . . . . . . . . . . . . . . . . . 42 4. Repeating sections of a lesson song . . . . . . . . . . 43 5. Recording a lesson song practice . . . . . . . . . . . . . 44 6. Finger Exercises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Concert Magic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 1. Performing a Concert Magic song . . . . . . . . . . . . 46 2. Concert Magic demo mode . . . . . . . . . . . . . . . . . . . 47 3. Concert Magic settings . . . . . . . . . . . . . . . . . . . . . . . 48 Steady Beat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 4. Concert Magic song arrangement types . . . . . . 49 Recorder Internal Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 1. Recording a song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 2. Playing a song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3. Internal Recorder Edit menu . . . . . . . . . . . . . . . . . . 53 4. Erasing a part/song . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 5. Converting a song to an audio file . . . . . . . . . . . . 55 USB Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 1. Recording an MP3/WAV audio file . . . . . . . . . . . . 56 2. Playing an MP3/WAV audio file . . . . . . . . . . . . . . . 58 3. Recording a MIDI song file . . . . . . . . . . . . . . . . . . . . 60 4. Playing a MIDI song file . . . . . . . . . . . . . . . . . . . . . . . 62 5. USB Recorder Edit menu . . . . . . . . . . . . . . . . . . . . . . 64 6. Converting a MIDI song file to an MP3/WAV audio file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 7. Overdubbing an MP3/WAV audio file . . . . . . . . . 66 8. Recording to an existing MIDI song file . . . . . . . 67 Settings Function menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 1. Key Transpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 2. Song Transpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 3. Tone Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 User Tone Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 4. Speaker Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 5. Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 6. Damper Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 7. Split . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 8. Four Hands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 9. Startup Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 10. Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 11. Auto Display Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 12. Auto Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Settings (cont.) Virtual Technician Settings . . . . . . . . . . . . . . . . . . . . . . . . . 83 1. Touch Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 User Touch Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 2. Voicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 User Voicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 3. Damper Resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 4. Damper Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 5. String Resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 6. Undamped String Resonance . . . . . . . . . . . . . . . . . 92 7. Cabinet Resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8. Key-off Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 9. Fall-back Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 10. Hammer Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 11. Topboard Simulation . . . . . . . . . . . . . . . . . . . . . . . . . 97 12. Decay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 13. Minimum Touch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 14. Stretch Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 User Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 15. Temperament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 User Temperament . . . . . . . . . . . . . . . . . . . . . . . . . . 103 16. Temperament Key . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 17. Key Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 User Key Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 18. Half-Pedal Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 19. Soft Pedal Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Phones Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 1. SHS Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 2. Phones Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 3. Phones Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 USB MIDI (USB to Host connector) . . . . . . . . . . . . . . . . . . . . . . . . 113 USB Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 1. Load Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 2. Load Registration All . . . . . . . . . . . . . . . . . . . . . . . . . 116 3. Load Registration Single . . . . . . . . . . . . . . . . . . . . . 117 4. Load Startup Setting . . . . . . . . . . . . . . . . . . . . . . . . . 118 5. Save Internal Song . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 6. Save SMF Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 7. Save Registration All . . . . . . . . . . . . . . . . . . . . . . . . . 121 8. Save Registration Single . . . . . . . . . . . . . . . . . . . . . 122 9. Save Startup Setting . . . . . . . . . . . . . . . . . . . . . . . . . 123 10. Rename File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 11. Delete File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 12. Format USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 * For information regarding MIDI functions and settings, please download the supplementary PDF manual from the Kawai Japan website: kawai-global.com/support/manual/ Bluetooth Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 1. Bluetooth Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 2. Bluetooth Audio Volume . . . . . . . . . . . . . . . . . . . . . 129 3. Bluetooth MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Appendix Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Connecting to Other Devices . . . . . . . . . . . . . . . . . . . . . . 135 Jack Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Headphone Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Demo Song List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Settings List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Sound List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Drum Sound Mapping List . . . . . . . . . . . . . . . . . . . . . . . . . 146 Drum Rhythm List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 9

Welcome to the Kawai CN39 digital piano 101 Feature Highlights ‘Responsive Hammer III’ weighted-key action, with Ivory Touch key surfaces and Let-off simulation The CN39 digital piano’s Responsive Hammer III (RHIII) action recreates the distinctive touch of an acoustic grand piano, with its realistic movement and accurate 3-sensor technology providing a smooth, natural, and highly responsive piano playing experience. The weight of the keyboard is appropriately graded to mirror the heavier bass hammers and lighter treble hammers of an acoustic piano, while structural reinforcements within the action assembly ensure greater stability during fortissimo and staccato passages. The CN39 digital piano also features Kawai’s Ivory Touch key surfaces that gently absorb finger moisture to assist the player’s performance, while, letVoff simulation recreates the subtle ‘notch’ sensation felt when softly playing the keys of a grand piano, satisfying the expectations of the most discerning pianists. Shigeru Kawai SK-EX and Kawai EX instruments reproduced with Harmonic Imaging sound technology The CN39 digital piano captures the magnificent tone of Kawai’s flagship Shigeru Kawai SK-EX full concert grand piano. Widely regarded as the ‘premier pianos of Japan’, Shigeru Kawai instruments grace the stages of concert halls and musical institutions throughout the world, and are prized for their exceptional tonal clarity. In addition, the CN39 also features the distinctive sound of Kawai’s highly acclaimed EX concert grand piano, which has frequently been selected by professional pianists in such prestigious events as the Chopin, Tchaikovsky, and Rubinstein international piano competitions, among others. Both instruments have been carefully recorded, meticulously analysed, and faithfully reproduced with full 88-key sampling using Harmonic ImagingTM sound technology. This unique process accurately recreates the broad dynamic range of the original grand pianos, affording pianists an extraordinary level of expressiveness ranging from the softest pianissimo to the strongest, boldest fortissimo. Strong selection of additional instrument sounds Supplementing the realistic acoustic piano voices, the CN39 digital piano also features an excellent selection of additional instrument sounds, ranging from electric pianos and drawbar and church organs, to strings, human choirs, and even atmospheric synth-style pads, inviting musicians to add greater variety to their performances. Furthermore, the Dual playing mode also allows two different sounds, such as grand piano and strings, to be layered together, while the Split and Four Hands modes divide the keyboard into two independent sections. The volume balances for each playing mode can also be adjusted quickly and easily using the real-time panel controls. Virtual Technician adjustments to personalise the instrument’s character The CN39 digital piano’s Virtual Technician feature allows various characteristics of the selected acoustic piano, electric piano, or harpsichord sound to be shaped at the touch of a button, with settings to adjust voicing and regulation, string, damper, and cabinet resonances, and subtle hammer, damper, and key release noises. It is even possible to adjust the precise tuning and volume of individual notes, before storing one’s personalised instrument configuration to memory. USB to Device functionality, with MP3/WAV file recording and playback The CN39 digital piano is equipped with USB connectors that not only allow this instrument to be connected to a computer for MIDI use, but also to load and save data to USB memory devices directly. This ‘USB to Device’ feature allows instrument settings or recorded songs stored in internal memory to be saved to USB for posterity, or standard MIDI files (SMF) downloaded from the internet to be conveniently played back without additional hardware. USB memory devices can also be used to play back MP3 or WAV audio files, allowing musicians to learn the chords or melody for a new piece, or to simply play along with their favourite songs. It is even possible to record performances as MP3 or WAV files for emailing to friends and family, listening to on the move, or for further editing using an audio workstation. Integrated Bluetooth® MIDI connectivity In addition to standard MIDI jacks for connecting to other instruments, the CN39 digital piano also boasts integrated Bluetooth MIDI and Audio technology that allows the instrument to communicate with supported smart devices wirelessly. Once connected to a phone, tablet, or laptop, CN39 digital piano owners can enjoy a wide variety of exciting music-related apps that enhance their learning and playing experience, or stream audio from songs and videos through the instrument’s speakers without additional cables. * Availability of Bluetooth function dependent on market location.

Wide range of connectivity options The CN39 digital piano features a variety of connectivity options, with Line-level output jacks that allow the instrument to be enjoyed in larger settings such as churches and schools. Standard MIDI and ‘USB to Host’ connectors ensure flexibility when using computers and other electronic instruments, while the Line-in jacks provide a convenient method of mixing in audio from a laptop, tablet, or other audio device. 2 Owner’s Manual Conventions This owner’s manual utilises a number of illustrative conventions in order to explain the CN39 digital piano’s various functions. The examples below provide an overview of the button LED indicator states and press types, and the appearance of difference kinds of text. ■ Button LED indicator states

LED indicator off: Sound/Function is not selected. LED indicator on: Sound/Function is selected. LED indicator flashing: Sound/Function is selected in a temporary state. LED indicator flashing: Sound/Function is selected in a temporary state. ■ Button press types Normal press: Select a sound or function. × 4 Press and hold: Select a function’s settings, or store registration memories etc. × 2 Press twice: Select a sound or function. Press multiple times: Cycle through sounds or settings. Press multiple times: Cycle through sounds or settings. hold hold ■ Text appearance Press and hold, then press X: Combine two sounds. Normal instruction and explanation text is written in regular type at 9 pt. size. * Notes about functions are marked with an asterisk and written in 8 pt. size. Reminders about previous operations are written in italic type at 9 pt. size. Reminders about previous operations are written in italic type at 9 pt. size. Reminders about previous operations are written in italic type at 9 pt. size. Captions explaining the LCD display or button functions, are written in bold type at 8.5 pt. size. Example operations are written in italic type at 8 pt. size, and enclosed within a grey box. 11

12Part Names and Functions 9 1 68 21314 15 16 17 18 19 20 USB PEDAL DC IN 15V to HOST IN MIDI OUT 3457101112

a POWER button This switch is used to turn the instrument on/off. Be sure to turn off the instrument after playing. * The CN39 digital piano features a power saving mode that can turn off the instrument automatically after a specified period of inactivity. For more information, please refer to the ‘Auto Power Off’ setting on page 82. b MASTER VOLUME slider This slider controls the master volume level of the instrument’s built-in speakers or headphones, if connected. * The MASTER VOLUME slider will also affect the volume level of the LINE OUT connectors. c LCD display The LCD display provides useful information such as the currently selected sound name, settings values, and the status of other functions when active. An example of the main play screen is shown below. Transpose status Headphones status Bluetooth status USB device status Selected sound Music menu Virtual Technician Function/Settings menu * A protective plastic film is attached to the display during production. Please remove this film before attempting to play the instrument. d FUNCTION button These buttons are used to select one of three functions/options shown at the bottom of the LCD display. e ARROW buttons These buttons are used to navigate around the various menus and screens, adjust values, and answer on-screen prompts. f EFFECTS button This button is used to turn effects for the selected sound on/off, to select the different effect types, and to adjust their settings. g REVERB button This button is used to turn reverb for the selected sound on/off, to select the different reverb types, and to adjust their settings. h METRONOME button This button is used to turn the metronome function on/off, and to adjust the tempo, time signature/beat, and volume settings. i PLAY/STOP button This button is used to start/stop the playback of demonstration songs, Piano Music pieces, and Lesson and Finger Exercises, and to start/stop the recording and playback of recorder songs, and MP3/WAV audio files. j REC button This button is used to record performances to internal memory or a USB memory device as MP3/WAV audio files. k SOUND buttons These buttons are used to select the sound(s) that will be heard when playing the keyboard of the CN39 digital piano. Multiple sounds are assigned to each category button, and can be selected by pressing the same button repeatedly. These buttons are also used to select Registration memories. l REGISTRATION button This button is used to store and recall one of the sixteen different registration memories. Each registration can store sound, reverb and effects settings, as well as various other panel options. m PHONES jacks These jacks are used to connect stereo headphones to the CN39 digital piano. 1/4” and 1/8” connectors are provided for convenience, and both can be used simultaneously, allowing two pairs of headphones to be connected at the same time. n USB to DEVICE port This port is used to connect a FAT or FAT32 formatted USB memory device to the instrument in order to load/save recorded song data, registration memories, and MP3/WAV/SMF files etc. o PEDAL connector This connector is used to connect the pedal board to the piano. p DC IN 15V connector This connector is used to connect the power adaptor to the piano. q USB to HOST port This port is use to connect the CN39 digital piano to a computer using a USB ‘B to A’ type cable in order to send and receive MIDI data. r MIDI IN / OUT jacks These jacks are used to connect the CN39 digital piano to external MIDI devices such as other musical instruments or a computer in order to send and receive MIDI data. * For more information about the instrument’s connectors and jacks, please refer to ‘Connecting to Other Devices’ on page 135. s LINE IN jacks These jacks are used to connect the stereo output (Left/Right 1/4” phone plug) from audio equipment, computers, or other electronic instruments to the CN39 digital piano’s amplifier and speakers. t LINE OUT jacks These jacks are used to connect the stereo output (Left/Right 1/4” phone plug) of the CN39 digital piano to external amplifiers, mixers, recording devices, and similar equipment. 13

14Setting Up the Piano 1 Power 1. Connecting the power adaptor to the instrument Connect the AC power adaptor to the DC IN terminal located on the underside of the instrument, as indicated below. 2. Connecting the power adaptor to an outlet Connect the AC power adaptor to an AC outlet. 3. Turning on the power Press the [POWER] button, located on the right hand side of the instrument’s front panel. The instrument will turn on, and the words ‘SK Concert Grand’ will be shown in the display, indicating that the SK Concert Grand sound is selected, and the instrument is ready to be played. * The CN39 digital piano incorporates power saving features that can turn off the display and the instrument automatically after a specified period of inactivity. For more information, please refer to the ‘Auto Display Off’ and ‘Auto Power Off’ settings on pages 81 and 82.

2 Key cover and music rest ■ Opening the key cover Gently lift the key cover with both hands, then slowly push it back, into the instrument’s body. To close the key cover, slowly pull the handle with both hands, then gently lower it downward. * Please close the lid slowly in order to avoid injury. ■ Adjusting the music rest Lift the music rest, then lower the metal prop (rear side) into the recessed holder to set the desired music rest angle. * The music rest can be set to one of three different angle positions. Prop and holder To lower the music rest, gently lift the prop from the recessed holder, then lower the music rest. * Please lower the music rest slowly in order to avoid injury. 15 16Setting up the Piano 3 Volume and headphones ■ Adjusting the volume The [MASTER VOLUME] slider controls the volume level of the instrument’s speakers, or headphones if connected. Move the slider up to increase the volume, and down to decrease the volume. Use this slider to set the volume to a comfortable listening level – the middle is often a good starting point. * The MASTER VOLUME slider will also affect the volume level of the LINE OUT connectors. * The maximum volume level of the speakers can be reduced by using the ‘Speaker Volume’ setting. Please refer to page 74 for more information. ■ Using headphones Use the jacks located beneath the keyboard on the left hand side, to connect stereo headphones to the CN39 digital piano. 1/4” and 1/8” connectors are provided for convenience. Two pairs of headphones can be connected and used simultaneously. When a pair of headphones is connected, sound will not be produced by the speakers. In addition, the headphones icon will appear at the top of the display. Headphones connected ■ Attaching the headphone hook (optional) A headphone hook is included with the CN39 digital piano and can be used to hang headphones when not in use. If desired, attach the headphone hook to the underside of the keyboard as shown in the illustration opposite. * For more information, please refer to the ‘Assembly Instructions’ on page 131. Increase volume Decrease volume 1 4 Pedals As with a grand piano, the CN39 digital piano features three pedals: sustain, sostenuto, and soft. ■ Sustain pedal (right pedal) Depressing this pedal sustains the sound after one’s hands have been lifted from the keyboard – greatly enriching the piano sound, while also assisting smooth ‘legato’ passages.

The sustain pedal is capable of responding to half pedaling. ■ Soft pedal (left pedal) Depressing this pedal softens the sound, reducing its volume. When the Jazz Organ sound is selected, the soft pedal is also used to alternate the speed of the rotary simulation between ‘Slow’ and ‘Fast’ effect modes. Soft pedal Sostenuto pedal ■ Sostenuto pedal (centre pedal) Depressing this pedal after playing the keyboard and before releasing the keys, sustains the sound of only those notes that have been played. Any keys that are subsequently played after the sostenuto pedal is depressed will not be sustained. Sustain pedal ■ Pedal support bolt A pedal support bolt is attached at the base of the pedal board to aid stability when the pedals are pushed. Turn the bolt anti-clockwise until it makes contact with the floor and supports the pedals firmly. If the pedal support bolt does not make contact with the floor, the pedal board may become damaged. Pedal support bolt

When moving the instrument, always adjust or remove the pedal support bolt, then readjust when the instrument is in its new position. ■ Caring for the pedals If the surface of the pedals becomes dirty, clean the pedals using a dry dish-washing sponge. Do not attempt to clean the pedals using rust-removing solvents, abrasives or files. ■ Grand Feel Pedal System The CN39 digital piano features the Grand Feel Pedal System, which replicates the sustain, soft, and sostenuto pedal weighting of a Shigeru Kawai SK Concert Grand piano. 17 18 Selecting Sounds The CN39 digital piano features a wide selection of realistic instrument sounds suitable for various musical styles. Sounds are arranged into eight categories, with several sounds assigned to each category button. For a complete listing of available instrument sounds, please refer to page 9 of the MIDI Settings manual. By default, the ‘SK Concert Grand’ sound will be selected automatically when the instrument is turned on. ■ Selecting a sound

Press the desired SOUND button. The LED indicator for the button will turn on to indicate that this category has been selected, and the name of the sound will be shown in the LCD display. Example: To select the E.PIANO category, press the E.PIANO button. LED indicator on: Sound category is selected. ■ Changing the sound Several sounds are assigned to each category button. Press the selected category button repeatedly to cycle through the different sound variations. × 3

Example: To select the ‘SK-5 Grand Piano’ sound, press the PIANO 1 button three times. The  or  buttons can also be used to select sounds and cycle through the different sound variations. * When selecting sounds assigned to the OTHERS category button, pressing and holding the  button then pressing the  button (and vice versa), can be used to cycle through the various sub-categories more quickly. 19 Dual Mode The Dual Mode function allows two sounds to be layered together, creating a more complex sound. For example, a piano sound layered with strings, or a church organ combined with a choir, etc. 1. Entering Dual mode Press and hold a SOUND button to select the main sound, then press another SOUND button to select the layered sound. The LED indicators for both SOUND buttons will turn on to indicate that Dual Mode is in use, and the respective sound hold names will be shown in the LCD display. Main sound Layered sound 2a. Changing the main/layered sounds: Method 1 To select a different variation for the layered sound: Press and hold the main SOUND button, then press the layered SOUND button repeatedly to cycle through the different sound variations. hold × 2 Example: To change the layered ‘Slow Strings’ sound to the ‘Warm Strings’ sound, press and hold the PIANO 1 button, then press the STRINGS button twice. To select a different variation for the main sound: Press and hold the layered SOUND button, then press the main SOUND button repeatedly to cycle through the different sound variations. hold × 3 Example: To change the main ‘SK Concert Grand’ sound to the ‘Mellow Grand’ sound, press and hold the STRINGS button, then press the PIANO 1 button three times. 2b. Changing the main/layered sounds: Method 2 It is also possible to change the main/layered sound without pressing and holding buttons.  buttons: Change sound variation. Press the  or  buttons to move the selection cursor over the main sound or layered sound. Press the  or  buttons to cycle through the different sound variations.  buttons: 20 Move selection cursor. Dual Mode settings The Dual Mode settings menu allows characteristics of the combined sound to be adjusted. ■ Dual Mode settings Dual Mode setting Description Default setting Balance Adjust the volume balance between the main and layered sounds. 9 - 9 Layer Octave Shift Raise/lower the pitch of the layered sound in octave steps. 0 Dynamics Adjust the dynamic sensitivity of the layered sound relative to the main sound. 10 ■ Entering the Dual Mode settings menu While the Dual Mode screen is shown in the LCD display: Press the FUNCTION button (EDIT). The Dual Mode settings menu will be shown in the LCD display. ■ Adjusting Dual Mode settings

After entering the Dual Mode settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. ■ Cycling between Dual, Split, and Four Hands modes  buttons: Adjust selected setting.  buttons: Move selection cursor.

When Dual Mode is selected, press the FUNCTION button to cycle between Split, Four Hands, and Dual modes. ■ Exiting Dual, Split, and Four Hands modes Press the FUNCTION button (EXIT) to exit Dual, Split, and Four Hands modes. * Preferred Dual Mode settings can be stored to a Registration memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 21 22 Split Mode The Split Mode function divides the keyboard into two sections, allowing each section to be played with a different sound. For example, a bass sound in the lower section, and a piano sound in the upper section. 1. Entering Split mode After entering Dual Mode (page 20): Press the FUNCTION button (SPLIT). The Split Mode screen will be shown in the LCD display. * The default split point is set between keys B3 and C4. The upper section and lower section sound names will be shown in the LCD display. The LED indicator for the upper section sound button will turn on, and the LED indicator for the lower section sound button will start to flash. Lower section sound LED indicator on: Upper section sound. Upper section sound LED indicator flashing: * By default, the lower section will be set to the ‘Wood Bass’ sound. Lower section sound. 2a. Changing the upper/lower section sounds: Method 1 To select a different sound for the upper section: Press the desired SOUND button. Example: To select the ‘Blues Organ' sound for the upper section, press the ORGAN button twice. * Preferred Split Mode upper/lower section sound combinations can be stored to a Registration memory for convenient recall. Please refer to page 35 for more information. 2b. Changing the upper/lower section sounds: Method 2 It is also possible to change the upper/lower section sound without pressing and holding buttons. Press the  or  buttons to move the selection cursor over the upper section or lower section sound. Press the  or  buttons to cycle through the different sound variations. To select a different sound for the lower section: Press and hold the FUNCTION button (4HAND), then press the desired SOUND button. × 2 hold × 3 Example: To select the 'W. Bass & Ride' sound for the lower section, press and hold the 1 FUNCTION button, then press the BASS button three times.  buttons: Change sound variation.  buttons: Move selection cursor. 3. Changing the split point Press and hold the FUNCTION button (4HAND), then press the desired split key on the keyboard. The name of the pressed key will briefly be shown in the LCD display, and will become the new split point. hold Lower section Upper section New split point Split Mode settings The Split Mode settings menu allows characteristics of the Split Mode sound and operation to be adjusted. ■ Split Mode settings Split Mode setting Description Default setting Balance Adjust the volume balance between the upper and lower sections. 9 - 9 Lower Octave Shift Raise/lower the pitch of the lower section sound in octave steps. 0 Lower Pedal Enable/disable the sustain pedal for the lower section sound. Off Split Point Specify the point along the keyboard that divides the upper and lower sections. C4 ■ Entering the Split Mode settings menu While the Split Mode screen is shown in the LCD display: Press the FUNCTION button (EDIT). The Split Mode settings menu will be shown in the LCD display. ■ Adjusting Split Mode settings After entering the Split Mode settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. * Preferred Split Mode settings can be stored to a Registration memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information.  buttons: Adjust selected setting.  buttons: Move selection cursor. 23 24 Four Hands Mode The Four Hands Mode function divides the keyboard into two sections in a similar way to that of the Split Mode function. However, with Four Hands Mode enabled, the octave/pitch of each section is automatically adjusted to create two separate 44-key instruments with the same playing range. Furthermore, the sustain (right) pedal and soft (left) pedal act as separate sustain pedals for the respective upper and lower sections, allowing two people to perform piano duets using a single instrument. 1. Entering Four Hands mode After entering Dual Mode (page 20): Press the FUNCTION button (SPLIT) once to enter Split Mode, then press the FUNCTION button (4HAND) again to select Four Hands Mode. * The default four hands mode split point is set between keys E4 and F4. The Four Hands Mode screen and right/left section sound names will be shown in the LCD display. Right section sound Left section sound * By default, the right and left sections will both be set to the ‘SK Concert Grand’ sound. 2a. Changing the right/left section sounds: Method 1 To select a different sound for the right section: Press the desired SOUND button. Example: To select the 'Classic E.Piano.' sound for the right section, press the E.PIANO button. * Preferred Four Hands Mode right/left section sound combinations can be stored to a Registration memory for convenient recall. Please refer to page 35 for more information. 2b. Changing the right/left section sounds: Method 2 It is also possible to change the right/left section sound without pressing and holding buttons. Press the  or  buttons to move the selection cursor over the right section or left section sound. Press the  or  buttons to cycle through the different sound variations.To select a different sound for the left section: Press and hold the FUNCTION button (DUAL), then press the desired SOUND button. holdExample: To select the 'Upright Piano' sound for the left section, press and hold the 1 FUNCTION button, then press the PIANO2 button.  buttons: Change sound variation.  buttons: Move selection cursor. 3. Changing the Four Hands mode split point Press and hold the FUNCTION button (DUAL), then press the desired split key on the keyboard. The name of the pressed key will briefly be shown in the LCD display, and will become the new split point.

hold Left section Right section New split point

Four Hands Mode settings The Four Hands Mode settings menu allows characteristics of the Four Hands Mode sound to be adjusted. ■ Four Hands Mode settings Four Hands Mode setting Description Default setting Balance Adjust the volume balance between the upper and lower sections. 9 - 9 Right Octave Shift Raise/lower the pitch of the right section sound in octave steps. – 2 Left Octave Shift Raise/lower the pitch of the left section sound in octave steps. + 2 Split Point Specify the point along the keyboard that divides the right and left sections. F4 ■ Entering the Four Hands Mode settings menu While the Four Hands Mode screen is shown in the LCD display: Press the FUNCTION button (EDIT). The Four Hands Mode settings menu will be shown in the LCD display. ■ Adjusting Four Hands Mode settings

After entering the Four Hands Mode settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. * Changes made to the Four Hands Mode settings will not affect the  buttons: Adjust selected setting.  buttons: Move selection cursor. 25

Split Mode settings, and vice versa. * Preferred Four Hands Mode settings can be stored to a Registration memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 26 Reverb Reverb adds reverberation to the sound, simulating the acoustic environment of a recital room, stage, or concert hall. Some sound types, such as acoustic piano, enable reverb automatically in order to improve acoustic realism. The CN39 digital piano features six different reverb types. ■ Reverb types Reverb type Description Room Simulates the ambiance of a small rehearsal room. Lounge Simulates the ambience of piano lounge. Small Hall Simulates the ambiance of a small hall. Concert Hall Simulates the ambiance of a concert hall or theater. Live Hall Simulates the ambiance of a live hall or stage. Cathedral Simulates the ambiance of a large cathedral. 1. Turning Reverb on/off Press the REVERB button to turn reverb on/off. The LED indicator for the REVERB button will turn on to indicate when reverb is in use, and the current status will briefly be shown in the LCD display. Reverb Reverb status type Reverb settings The Reverb settings menu allows the type and characteristics of the reverb to be adjusted. ■ Reverb settings Reverb setting Description Range Type Changes the type of environment. – Depth Adjusts the depth of the environment (i.e. amount of reverberation to apply). 1~10 Time Adjusts the decay length/speed of the reverberation. 1~10

■ Entering the Reverb settings menu Press and hold the REVERB button. The Reverb settings menu will be shown in the LCD display. ■ Adjusting Reverb settings After entering the Reverb settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. ■ Exiting the Reverb settings menu Press the FUNCTION button (EXIT) to exit the Reverb settings menu. * Reverb settings are independent for each sound variation. * Any changes made to the reverb type, settings, or on/off status will remain until the power is turned off. * Preferred reverb settings can be stored to a Registration memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. hold  buttons: Adjust selected setting.  buttons: Move selection cursor. 27

28 Effects In addition to reverb, various other effects can be applied to the selected sound, altering the tonal character and feeling of the instrument. As with reverb, some sound types enable certain effects automatically in order to enhance tonal quality. The CN39 digital piano features 19 different effect types, with 2 combination effects, and 3 additional amplified effects. ■ Effect types Effect type Description Mono Delay Applies an echo effect to the sound, playing through both speakers simultaneously. Ping Delay Applies a ‘ping pong’ echo effect to the sound, giving the impression that it is ‘bouncing’ from left to right. Triple Delay Similar in principle to Ping Delay, but with an additional centre echo. Chorus Layers a slightly detuned version of the sound over the original, thus enriching its tonal character. Classic Chorus Similar in principle to Chorus, but intended for vintage electric piano sounds. Ensemble Applies a three-phase chorus to the sound, providing additional richness. Tremolo Continuously varies the volume at a constant speed, adding a vibrato type effect to the sound. Classic Tremolo Similar in principle to Tremolo, but intended for vintage electric piano sounds. Vibrato Tremolo Similar in principle to Tremolo, but with an additional Vibrato effect applied. Auto Pan Alternates the sound output from left to right across the stereo field using a sine wave. Classic Auto Pan Similar in principle to Auto Pan, but intended for vintage electric piano sounds. Phaser Applies a cyclic phase change to the sound, giving the impression that the sound is moving. Classic Phaser Similar in principle to Phaser, but intended for vintage electric piano sounds. Simulates the sound of a rotary speaker commonly used with vintage electronic organs. Rotary (1~6) There are three different levels of overdrive, with and without a Chorus effect. * The soft pedal can be used to alternate the speed of the rotary simulation between ‘Slow’ and ‘Fast’ effect modes. Combination Effects Different combinations of the above effects, applied simultaneously. * Combination effect types: Phaser+Chorus, Phaser+AutoPan Amplified Effects A selection of the above effects, with a vintage electric piano speaker effect applied. * Amplified effect types: Tremolo+Amp, Auto Pan+Amp, Phaser+Amp 1. Turning Effects on/off Press the EFFECTS button to turn effects on/off. The LED indicator for the EFFECTS button will turn on to indicate when effects are in use, and the current status will briefly be shown in the LCD display. Effect Effect status type * If a drum kit sound is selected, the Effects Edit screen will not be shown. ■ Effects settings Effect type Effect setting Description Mono Delay / Ping Delay / Triple Delay Dry / Wet Adjust the intensity of the delay. Time Adjust the interval of time between each delay. Chorus / Ensemble Dry / Wet Adjust the intensity of the chorus. Speed Adjust the speed of the chorus.

■ Effects settings (cont.) Effect type Effect setting Description Classic Chorus Mono / Stereo Toggle between a Mono or Stereo effect. Speed Adjust the speed of the chorus. Tremolo / Classic Tremolo / Vibrato Tremolo Dry / Wet Adjust the intensity of the tremolo. Speed Adjust the speed of the tremolo. Auto Pan / Classic Auto Pan Dry / Wet Adjust the intensity of the pan. Speed Adjust the speed of the pan. Phaser / Classic Phaser Dry / Wet Adjust the intensity of the phaser. Speed Adjust the speed of the phaser. Rotary Accel. Speed Adjust the acceleration speed between slow and fast modes. Rotary Speed Adjust the speed of the rotary speaker. Combination Effects / Amplified Effects Dry / Wet Adjust the intensity of the effects. Speed Adjust the speed of the effects. ■ Entering the Effects settings menu Press and hold the EFFECTS button. The Effects settings menu will be shown in the LCD display. ■ Adjusting Effects settings

After entering the Effects settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. ■ Exiting the Effects settings menu Press the FUNCTION button (EXIT) to exit the Effects settings menu. * Effects settings are independent for each sound variation. * Any changes made to the effects type, settings, or on/off status will remain until the power is turned off. * Preferred effects settings can be stored to a Registration memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. hold  buttons: Adjust selected setting.  buttons: Move selection cursor.

* If a drum kit sound is selected, the Effects Edit screen will not be shown. 29 30 Virtual Technician In addition to the reverb and effects functions, the overall character of the CN39 acoustic piano sounds can also be dramatically adjusted using the instrument’s Virtual Technician feature. There are two methods of using the Virtual Technician: Smart Mode and Advanced Mode. 1 Smart Mode In Smart Mode, the Virtual Technician intelligently performs a collection of adjustments for the player, based on ten preset attributes such as ‘Soft’ or ‘Strong’, ‘Brilliant’ or ‘Dark’. This mode is recommended for musicians that wish to enjoy different piano characteristics, without delving into the individual parameters of Advanced Mode. 1. Entering Virtual Technician Smart Mode While the normal playing mode screen is shown in the LCD display: Press the FUNCTION button (VT). The Virtual Technician menu will be shown in the LCD display, and Smart Mode will be selected automatically. Press the FUNCTION button (EDIT). The list of Smart Mode presets will be shown in the LCD display. 2. Selecting the Virtual Technician preset While the Smart Mode presets screen is shown in the LCD display: Press the  or  buttons to select the desired Virtual Technician Smart Mode preset. The Virtual Technician adjustments will be applied to the selected sound immediately. * Smart Mode will be disabled by default (‘Off’ preset). When disabled, the Advanced Mode Virtual Technician parameter settings will used.  buttons: Select Virtual Technician preset * Smart Mode presets are independent for each sound variation. * The selected Smart Mode preset will be used for the current sound variation until the power is turned off. However, it is possible to store a Smart Mode preset to a sound. For more information, please refer to the instructions on the following page. ■ Showing the Virtual Technician Help screen Press the FUNCTION button (HELP). A brief explanation about the currently selected Virtual Technician preset will be shown in the LCD display. Press the  or  buttons to scroll through the explanation if necessary. Press the FUNCTION button (BACK) to return to the Virtual Technician preset selection screen. ■ Storing the Virtual Technician preset to the selected sound After selecting the Smart Mode preset: Press the FUNCTION button (STORE). The selected Smart Mode preset will be saved to the current sound variation, and a confirmation message will briefly be shown in the LCD display. 2 Advanced Mode In Advanced Mode, the player is given full control over every aspect of the piano’s configuration, allowing precise adjustments over hammer hardness, action regulation, cabinet size, and a variety of other acoustic characteristics. This mode is recommended for musicians that enjoy fine-tuning individual details of the piano sound in order to suit their personal preferences. * For more information about the individual Virtual Technician parameters, please refer to page 83. ■ Entering Virtual Technician Advanced Mode While the normal playing mode screen is shown in the LCD display: Press and hold the FUNCTION button (VT).

The Virtual Technician Settings menu will be shown in the LCD display, allowing parameters to be adjusted in Advanced Mode. * The stored Smart Mode preset will be retained after the power is turned off, and will be used automatically whenever the sound variation is selected. hold * It is also possible to access Advanced Mode via the Virtual Technician menu, or by selecting Virtual Tech. in the Function menus. * It is also possible to make adjustments to a Smart Mode preset by selecting it, and then entering Advanced Mode. However, any adjustments cannot be re-stored back to the Smart Mode preset list. 31

32 Metronome / Drum Rhythms The Metronome function provides a steady beat to aid practicing the piano at a consistent tempo. In addition to regular metronome beats, the CN39 digital piano also features a variety of drum rhythms to accompany most playing styles and musical genres. For a complete listing of available drum rhythms, please refer to page 148 of this owner’s manual. ■ Turning the Metronome on/off Press the METRONOME button. The LED indicator for the METRONOME button will turn on to indicate that the metronome function is in use, and a 4/4 beat will start to count. The current metronome tempo in beats per minute (BPM) and beat of the bar will also be shown in the LCD display. Tempo Beat Press the METRONOME button again to stop the metronome. The LED indicator for the METRONOME button will turn off. Metronome settings The Metronome settings menu allows the tempo, beat, and volume of the metronome to be adjusted. ■ Metronome settings Metronome setting Description Range Tempo Adjust the tempo of the metronome beat / drum rhythm in beats per minute (BPM). 10~400 bpm Beat Change the metronome beat (time signature) / drum rhythm. * There are ten different time signature available: 1/4, 2/4, 3/4, 4/4, 5/4, 3/8, 6/8, 7/8, 9/8, and 12/8. – Volume Adjusts the volume of the metronome beat / drum rhythm. 1~10 ■ Entering the Metronome settings menu Press and hold the METRONOME button. The Metronome settings menu will be shown in the LCD display. hold ■ Adjusting Metronome settings After entering the Metronome settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. ■ Drum rhythms As an alternative to the simple metronome count, it is also possible to select a drum pattern from one of 100 different rhythm styles. Enter the Metronome settings menu and select the Beat setting. Press the  or  buttons to cycle through the available beats until reaching the ‘8 Beat 1’ drum rhythm. Drum rhythm  buttons: Adjust selected setting.  buttons: Move selection cursor.  buttons: Select drum rhythm. Continue to press the  or  buttons to select the desired drum rhythm. * For a complete listing of available drum rhythms, please refer to page 148 of this owner’s manual. ■ Exiting the Metronome settings menu Press the FUNCTION button (EXIT) to exit the Metronome settings menu. * Any changes made to the metronome tempo, beat, or volume settings will remain until the power is turned off. * Preferred metronome settings can be stored to a Registration memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. ■ Recording with the metronome

It is also possible to record songs with the metronome activated. This is useful when recording parts separately, or wishing to maintain correct timing throughout complex passages. Note that the standard metronome ‘click’ will not be heard when the song is played back. * For more information about the instrument’s Recorder function, please refer to page 50. 33 34 Registration Memories The Registration function allows the current instrument setup (sound selections, split point, reverb and effect settings, and various other panel options) to be stored to a memory and conveniently recalled at the touch of a button. There are two banks (‘A’ and ‘B’) for each registration button, allowing up to 16 different registration memories to be stored. Registrations can also be loaded/saved to a USB memory device. Please refer to pages 117/122 for more information. ■ Functions and Settings stored in Registration memories Functions Selected sound (including primary sound for each category) Dual Mode / Split Mode / Four Hands Mode (including settings) Reverb, Effects (Type, Settings) Metronome (Beat, Tempo, Volume) Settings Basic Settings (with exceptions) Virtual Technician Settings MIDI Settings * Changes made to the Auto Power Off setting will be stored to User Memory automatically. * For a complete listing of the settings that can be stored to Registration memories, please refer to pages 140~141. 1 Selecting a Registration memory ■ Entering Registration mode Press the REGISTRATION button. The LED indicator for the REGISTRATION button will turn on to indicate that the registration function is in use. ■ Selecting a Registration memory When the registration function is in use: Press the FUNCTION button to toggle between registration memory bank ‘A’ and ‘B’. Press a SOUND button to select the desired registration memory. The name of the selected registration memory will be shown in the LCD display. Registration name Select Bank A/B ■ Exiting Registration mode Press the REGISTRATION button. The LED indicator for the REGISTRATION button will turn off, and the button panel will return to normal operation. Example: To select registration memory B-3 (when bank ‘A’ is selected), press the FUNCTION button, then press the E.PIANO (memory 3) button.

2 Storing a Registration memory 1. Entering Registration Store mode While the normal playing mode screen is shown in the LCD display: Press and hold the REGISTRATION button. The registration memory (SOUND) buttons will start to flash. 2. Selecting the Registration memory Press the or FUNCTION buttons to select the registration memory bank ‘A’ and ‘B’, then press a registration memory (SOUND) button. The Registration name screen will be shown in the LCD display. 3. Naming the Registration memory Enter a name for the registration memory by pressing the  or  buttons to cycle through the alphanumeric characters, and the  or  buttons to move the cursor. 4. Storing the Registration to memory Press the FUNCTION button (STORE) to confirm the store operation, or the FUNCTION button (EXIT) to cancel. Upon storing, a beep will sound and a confirmation message will briefly be shown in the LCD display. The current instrument setup will be stored to the selected registration memory with the specified name. holdExample: To store the current instrument setup to memory A-2, press the FUNCTION button, then press the PIANO 2 (memory 2) button.  buttons: Move selection cursor.  buttons: Select character. STORE EXIT

* The stored registration will remain in memory after the instrument is turned off, or if the instrument’s power cable is disconnected from the wall outlet. 35 36 Registration Memories 3 Registration Edit menu The Registration Edit menu allows the currently selected registration memory to be opened in normal playing mode (for further adjustment, or simply to check which sounds are used etc.), or to be saved to USB memory. ■ Entering the Registration Edit menu When the registration function is in use: Press the FUNCTION button (EDIT). The Registration Edit menu will be shown in the LCD display. ■ Opening the Registration Press the  or  buttons to select the Open Registration function, then press the FUNCTION button (OK). The currently selected registration memory will be opened in normal playing mode, allowing additional changes and adjustments to be made. ■ Saving the current Registration memory to USB Press the  or  buttons to select the Save Registration function, then press the FUNCTION button (OK). The Save Regist Single function of the USB Menu will be shown in the LCD display, with the current registration selected. * Please refer to the Save Registration Single instructions on page 122. ■ Resetting all Registration memories Press and hold the REGISTRATION and REC buttons, then turn the instrument’s power off/on. All registrations will be reset to the factory default settings.  buttons: Move selection cursor. * For more information about storing the adjusted registration, please refer to page 35.  buttons: Move selection cursor. Panel Lock The Panel Lock function allows the state of all panel buttons to be temporarily locked, preventing sounds and other settings from being changed. This function may prove useful in teaching environments, ensuring that students are not distracted by changing sounds etc. 1. Activating the Panel Lock While the normal playing mode screen is shown in the LCD display: Press the  and  buttons simultaneously. The Panel Lock screen will be shown in the LCD display, and the instrument will stop responding to panel button presses. 2. Deactivating the Panel Lock While the Panel Lock is activated: Press and hold the FUNCTION button (UNLOCK). The Panel Lock will be deactivated, and the instrument will hold resume responding to panel button presses as normal. * The Panel Lock can only be activated from the main playing screen. * When activated, the Panel Lock will remain until the power is turned off, or the lock is deactivated. * While Panel Lock is activated, the LED indicators for all buttons will turn off, however the LED indicator for the FUNCTION button will flash. 37 38 Demo Songs The Demo function provides an excellent introduction to the varied capabilities of CN39 digital piano. There are over 30 different demonstration songs available, highlighting the instruments’ rich selection of high quality sounds and its power speaker system. For a complete listing of demonstration songs, please refer to page 139 of this owner’s manual. ■ Entering Demo mode Press the FUNCTION button (MUSIC). The Music Menu will be shown in the LCD display. Demo mode will be selected automatically. Press the FUNCTION (ENTER) or PLAY/STOP buttons. The LED indicator for the PIANO 1 button will start to flash, and the ‘SK Concert Grand’ demo song will start to play. ■ Selecting a demo song While Demo mode is selected: Press a SOUND button to select a sound category. The first demo song of the sound category will start to play. Press the  or  buttons to cycle through the demo songs in the selected sound category, and the  or  buttons to cycle through the different sound categories. * When the selected song has finished, the next demo song in the category will begin to play automatically. ■ Stopping the demo song and exiting Demo mode Press the FUNCTION (BACK) or PLAY/STOP buttons while the song demo is playing. The LED indicator for the selected SOUND button will stop flashing, and the song demo will stop playing. Press the FUNCTION (EXIT) button to exit the Music Menu. or  buttons: Select demo song  buttons: Select sound category Piano Music In addition to the sound demonstration songs, the CN39 digital piano also features a selection of popular classical piano works from the Baroque and Romantic periods. Notated scores are provided in the separate ‘Classical Piano Collection’ book*, assisting the musical appreciation and study of each piece. * Depending on market location. For a complete listing of Piano Music pieces, please refer to the separate ‘Internal Song Lists’ booklet. ■ Entering Piano Music mode Press the FUNCTION button (MUSIC), then press the  or  buttons to select Piano Music mode. Press the FUNCTION (ENTER) or PLAY/STOP buttons. The LED indicator for the PIANO 1 button will start to flash, and the piece ‘Tambourin’ by Rameau will start to play. ■ Selecting a piano music piece While Piano Music mode is selected: Press the  or  buttons to cycle through the different piano music pieces. The title and composer of the selected piece will be shown in the LCD display. * The balance of the left hand and right hand parts can be adjusted by Title pressing the FUNCTION (EDIT) button, and adjusting the Balance Composer setting. ■ Replaying the selected piano music piece When the selected piano music piece has finished: Press the PLAY/STOP button to replay the piano music piece. ■ Stopping the piano music piece and exiting Piano Music mode Press the FUNCTION (BACK) or PLAY/STOP buttons while the piano music piece is playing. The LED indicator for the PLAY/STOP button will turn off, and the piano music piece will stop playing. Press the FUNCTION (EXIT) button to exit the Music Menu. 39 40 Lesson Function The Lesson function allows budding pianists to practice the piano using a selection of built-in song books and finger exercises. The left and right hand parts of each piece can be practiced separately, adjusting the tempo to perfect difficult passages, before being recorded for self-evaluation. ■ Built-in lesson mode song books Alfred Lesson Books Alfred’s Premier Piano Course Lesson 1A Alfred’s Premier Piano Course Lesson 1B Alfred’s Basic Piano Library Lesson Book Level 1A Alfred’s Basic Piano Library Lesson Book Level 1B Alfred’s Basic Adult Piano Course Lesson Book Level 1 Classical Lesson Books Burgmüller 25 (25 Etudes Faciles, Opus 100) Czerny 30 (Etudes de Mécanisme, Opus 849) Czerny 100 (Hundert Übungsstücke, Opus 139) Beyer 106 (Vorschule im Klavierspiel, Opus 101) J.S. Bach: Inventionen Sonatinen Album 1 * Lesson books sold separately – please refer to the separate ‘Internal Song Lists’ booklet for more information. Chopin Walzer (Chopin waltzes series 1-19) 1 Selecting a lesson book/song 1. Entering lesson mode Press the FUNCTION button (MUSIC), then press the  or  buttons to select Lesson Mode. Press the FUNCTION button (ENTER) to enter lesson mode. The name of the selected lesson book, song, and current bar will be shown in the LCD display. 2. Selecting a lesson book/song Press the  or  buttons to move the selection cursor over the lesson book name or song title. Press the  or  buttons to cycle through the different lesson books and song titles. Book name Song title It is also possible to select songs by pressing and holding the FUNCTION button (EDIT), then pressing the relevant key on the keyboard.  buttons: Select lesson book/song. * Please refer to the separate ‘Internal Song Lists’ booklet for a complete listing of available lesson books/songs and corresponding key numbers.  buttons: Move selection cursor. 2 Listening to the selected lesson song This page will explain how to play and stop the selected lesson song, and change the playback position. 1. Playing the lesson song After selecting a lesson book and song: Press the PLAY/STOP button. The LED indicator for the PLAY/STOP button will turn on, and a one bar count-in will be heard before the song starts to play. 2. Changing the playback position (Bar)

Press the  or  buttons to move the selection cursor over the third line of the LCD display (Bar). Press the  or  buttons to rewind or cue the playback position (Bar) of the current song. Current bar It is also possible to rewind or cue the playback position without selecting ‘Bar’, by pressing the REVERB or EFFECTS buttons. To reset the playback position to the first bar of the song, press the REVERB and EFFECTS buttons simultaneously. ■ Stopping and resuming the lesson song While the lesson song is playing: Press the PLAY/STOP button to stop the lesson song playback. Press the PLAY/STOP button once again to resume playback from the stopped position. 3. Exiting lesson mode Press the FUNCTION (EXIT) button to exit the Music Menu. * If the first bar of the song begins on an ‘up’ beat (i.e. pickup notes),  buttons: Change playback position.  buttons: Move selection cursor.

the first bar number will be shown as zero in the LCD display. * The metronome will not continue after the count-in bar, but can be turned on manually by pressing the METRONOME button. 41 Lesson Function  buttons: Adjust left/right-hand volume. Example: To practice the right-hand part while listening to the left-hand part, set the volume balance to 9 - 1.  buttons: Adjust playback tempo. 42 3 Lesson Function settings The Lesson Function settings menu allows the left and right-hand part volumes of the current lesson song to be adjusted, allowing each part to be practiced separately. It is also possible to adjust the playback tempo of the current lesson song, allowing difficult passages to be practised more conveniently. ■ Lesson Function settings Lesson Function setting Description Default setting Balance Adjust the volume balance between the left and right-hand parts. 9 - 9 Tempo Adjust the playback tempo of the current lesson song in beats per minute (BPM). Song specific ■ Entering the Lesson Function settings menu After selecting a lesson book and song: Press the FUNCTION button (EDIT). The Lesson Function settings menu will be shown in the LCD display. ■ Adjusting the left/right-hand part volume Press the  or  buttons to move the selection cursor over the Balance setting, then press the  or  buttons to adjust the volume of the left/right-hand part volume. Increasing the volume of the left-hand part will reduce the volume of the right-hand part, and vice versa. * If the Beyer lesson book is selected, increasing the left-hand value will decrease the volume of the student’s part, while increasing the right- hand value will decrease the volume of the teacher’s part. ■ Adjusting the playback tempo of the lesson song Press the  or  buttons to move the selection cursor over the Tempo setting, then press the  or  buttons to adjust the playback tempo of the lesson song. * To reset the playback tempo of the selected lesson song to the default value, press the  and  buttons simultaneously. 4 Repeating sections of a lesson song The ‘A-B Loop’ feature of the Lesson Function allows sections of the selected lesson song to be ‘looped’ between two points in order to practise difficult passages continuously. 1. Playing the lesson song After selecting a lesson book and song: Press the PLAY/STOP button. The LED indicator for the PLAY/STOP button will turn on, and a one bar count-in will be heard before the song starts to play. 2. Specifying the start point (A) of the loop Press the FUNCTION button (A-B) to specify the start point of the loop. The LED indicator for the FUNCTION button will start to flash, indicating that the start point (A) of the loop has been set. Point ‘A’ set 3. Specifying the end point (B) of the loop Press the FUNCTION button (A-B) again to specify the end point of the loop. The LED indicator for the FUNCTION button will turn on, indicating that the end point of the (B) of the loop has been set. Point ‘B’ set: loop active

The defined ‘A-B’ section of the lesson song will repeat (loop), allowing the passage to be practiced continuously. 4. Cancelling the ‘A-B’ loop Press the FUNCTION button (A-B) once again to cancel the loop. The LED indicator for the FUNCTION button will turn off, and the lesson song will resume normal playback. * The Balance and Tempo lesson function settings can continue to be adjusted while the A-B loop is in operation. 43

Lesson Function * It may be desirable to adjust the Balance and Tempo lesson function settings before starting the recording. * The Balance and Tempo lesson function settings can continue to be adjusted while the recorded lesson song practise is playing. * The ‘A-B’ loop function cannot be used when recording a lesson song practice. * Press the REC and PLAY/STOP buttons simultaneously to erase the recorded lesson song practice. The recorded practice will be erased automatically when a different lesson song is selected. 44 5 Recording a lesson song practice The Lesson Function’s Record feature allows the left or right-hand parts of the selected lesson song to be recorded to internal memory, and then played back for self-evaluation. 1. Starting the lesson song recording After selecting a lesson book and song: Press the REC button. The LED indicators for the REC and PLAY/STOP buttons will turn on to indicate that recording mode is in use. A one bar count-in will be heard before the lesson song starts to play and record. 2. Stopping the lesson song recording Press the PLAY/STOP button. The LED indicators for the REC and PLAY/STOP buttons will turn off, and the lesson song recording and playback will stop. 3. Playing back the recorded lesson song Press the PLAY/STOP button again. The LED indicator for the PLAY/STOP button will turn on, and a one bar count-in will be heard before the recorded lesson song starts to play. Press the PLAY/STOP button. The LED indicator for the PLAY/STOP button will turn off, and the recorded lesson song will stop playing.

6 Finger Exercises The lesson function also includes a selection of finger exercises for practicing major and minor scales, arpeggios, chords, cadences, and Hanon exercises, with notated scores provided in the separate ‘Finger Exercises’ book. The CN39 digital piano can also evaluate one’s practice, analysing note accuracy, timing evenness, and note volume consistency, before displaying results for each category. Using this function, players can objectively review their performances, and concentrate on improving a particular area of their technique. 1. Selecting and recording a Hanon finger exercise While Lesson mode is in use: Select the Hanon lesson book, then select a song number. Press the REC button. The LED indicators for the REC and PLAY/STOP buttons will turn on to indicate that recording mode is in use. A one bar count-in will be heard before the finger exercise starts to play and record. 2. Evaluating the recorded finger exercise Press the PLAY/STOP button The LED indicators for the REC and PLAY/STOP buttons will turn off, and the finger exercise recording and playback will stop.

The recorded practice will be evaluated for note accuracy, timing evenness, and volume consistency, with the results shown alternately in the LCD display. 3. Playing back the recorded finger exercise Press the PLAY/STOP button again. The LED indicator for the PLAY/STOP button will turn on, and a one bar count-in will be heard before the recorded finger exercise starts to play. Press the PLAY/STOP button once again. The LED indicator for the PLAY/STOP button will turn off, and the recorded finger exercise song will stop playing. * It may be desirable to adjust the Balance and Tempo lesson function * Press the REC and PLAY/STOP buttons simultaneously to erase the recorded lesson song practice. The recorded practice will be erased automatically when a different lesson song is selected. * Press  or  buttons to cycle through the evaluation results. The recorded finger exercise can be replayed even after cancelling the evaluation result screen. 45 45

settings before starting the recording. 46 Concert Magic The Concert Magic function allows complete beginners to enjoy playing the piano by simply selecting one of the 176 pre-programmed songs, then tapping the keyboard with a steady rhythm and tempo. For a complete listing of available Concert Magic songs, please refer to the separate ‘Internal Song Lists’ booklet. 1 Performing a Concert Magic song The 176 Concert Magic songs are divided into banks ‘A’ and ‘B’, with each bank containing 88 songs. 1. Entering Concert Magic mode Press the FUNCTION button (MUSIC), then press the  or  buttons to select Concert Magic. Press the FUNCTION button (ENTER) to enter Concert Magic. The bank, number, and name of the selected Concert Magic song will be shown in the LCD display. 2. Selecting a Concert Magic song While Concert Magic mode is in use: Press and hold the FUNCTION button (EDIT), then press the key to which the Concert Magic song (bank ‘A’) is assigned. A Concert Magic song from bank ‘A’ will be selected, with the song number and name shown in the LCD display. * To select a song from bank ‘B’, press the same key again. Repeatedly pressing the same key will alternate between banks ‘A’ and ‘B’. 3. Performing the selected Concert Magic song Press a key on the keyboard. The song will advance with every key that is pressed. Pressing the keys gently will produce a soft sound, while pressing heavily will produce a loud sound. As the song advances, the • symbols shown in the LCD will be replaced by  symbols. This is called the Note Navigator. hold 4. Changing the Concert Magic playback sound Press a SOUND button to change the sound used for the Concert Magic song (melody and accompaniment parts). It is also possible to select independent sounds for the melody and accompaniment parts: Press the FUNCTION button (SPLIT), to enable Concert Magic split mode. Press a SOUND button to change the melody sound. Press and hold the FUNCTION button (SPLIT), then press a SOUND button to change the accompaniment sound. 5. Exiting Concert Magic mode Press the FUNCTION button (BACK), to exit Concert Magic mode. 2 Concert Magic demo mode This function allows all of the Concert Magic songs to be played back randomly or in designated categories. ■ Random playback Enter Concert Magic mode and select the desired song. Press the PLAY/STOP button. All 176 Concert Magic songs will be played in a random order until the PLAY/STOP button is pressed again. ■ Category playback Enter Concert Magic mode and select the desired song. Press and hold the FUNCTION button (EDIT), then press the PLAY/STOP button.

Songs in the same category as the selected song, will be played in sequential order until the PLAY/STOP button is pressed again. hold Example: If the song ‘Row, Row, Row Your Boat’ is selected, all other songs in the ‘Children’s Songs’ category will be played.

hold 47 48 Concert Magic 3 Concert Magic settings The Concert Magic settings menu allows the playback tempo, playing mode, and volume balance to be adjusted. ■ Concert Magic settings Concert Magic setting Description Default setting Tempo Adjust the playback tempo of the Concert Magic song in beats per minute (BPM). Song specific Mode Change the Concert Magic playing mode (see below). Normal Balance Adjust the volume balance between the melody and accompaniment parts. 9 - 9 ■ Entering the Concert Magic settings menu While Concert Magic mode is in use: Press the FUNCTION button (EDIT). The Concert Magic settings menu will be shown in the LCD display. ■ Adjusting Concert Magic settings After entering the Concert Magic settings menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. Steady Beat mode Steady Beat mode allows all Concert Magic songs to be played by simply tapping any key with a constant steady beat, regardless of the song arrangement type.  buttons: Adjust selected setting.  buttons: Move selection cursor. 4 Concert Magic song arrangement types Concert Magic songs are divided into three different arrangement types, each requiring a different level of skill to be performed correctly. * The Concert Magic arrangement type is for each song is indicated in the ‘Internal Song Lists’ booklet as ‘EB’, ‘MP’, or ‘SK’. ■ Easy Beat These are the easiest songs to play. To perform them, simply tap out a constant steady beat on any key on the keyboard. The following example shows the notated score for ‘Für Elise’, indicating that a constant, steady rhythm should be maintained throughout the song. This is the distinguishing characteristic of an Easy Beat song. Key on: X X X X X X X X X XX X X X X X X X X X ■ Melody Play These songs are also relatively easy to play, especially if they are familiar to the player. To perform them, tap out the rhythm of the melody on any key of the keyboard. Singing along as the rhythm is tapped can be helpful. The following example shows the notated score for ‘Twinkle, Twinkle, Little Star’. * When performing fast Concert Magic songs, it may be easier to tap different keys with two alternating fingers in order to play at a greater speed. Key on: X X X X X X X X X X X X X X ■ Skillful These songs range in difficulty from moderately difficult to difficult. To perform them, tap out the rhythm of both the melody and the accompaniment notes on any key of the keyboard. The Note Navigator will be very helpful when playing the Skillful type songs. The following example shows the notated score for ‘Waltz of the Flowers’. Key on X X X X X X X X X X X X X EBMPSK 49 50Internal Recorder The CN39 digital piano allows up to 10 different songs to be recorded, stored in internal memory, and played back at the touch of a button. Each song consists of two separate tracks – referred to as ‘parts’ – that can be recorded and played back independently. This allows the left-hand part of a song to be recorded first on one track, and the right-hand part to be recorded later on the other track. 1 Recording a song 1. Entering song recorder mode Press the REC button. The LED indicator for the REC button will start to flash, and the Internal Recorder record screen will appear with the currently selected song and part number shown in the LCD display. 2. Selecting the song/part to be recorded Press the  or  buttons to move the selection cursor over the song memory or part. Press the  or  buttons to change the selected song memory or part to be recorded. If a part has already been recorded, a * symbol will be shown. Part has been recorded When recording part 1 and part 2 separately, select the song and part number carefully in order to prevent accidentally overwriting a previously recorded part. 3. Starting the song recorder Press a key on the keyboard, or the PLAY/STOP button. The LED indicators for the REC and PLAY/STOP buttons will turn on, and recording will start. Metronome tempo/beat (if enabled) Recording * If a USB memory device is connected, press the FUNCTION button (INT) to select the internal song recorder. or * Pressing the PLAY/STOP button allows a rest period or empty bar to be inserted at the beginning of the song. * Press the METRONOME button before or during the recording to turn on the metronome. The metronome ‘click’ sound will not be recorded.  buttons: Select song memory/part.  buttons: Move selection cursor. 4. Stopping the song recorder Press the PLAY/STOP button. The LED indicators for the PLAY/STOP and REC buttons will turn off, the recorder will stop, and the part/song will be stored in internal memory. After a few seconds, the Internal Recorder play screen will be shown in the LCD display, indicating that the song is ready for playback. * The maximum recording capacity is approximately 90,000 notes, with button and pedal presses also counted as one note. Stopped * If the maximum recording capacity is reached during recording, the recorder will stop automatically. Part Recorded * Recorder songs will remain in memory after the power is turned off. To play back the recorded song, please refer to the ‘Playing a Song’ instructions on page 52. ■ Recording a second part To record a second part, repeat the above instructions, selecting the part that has not been recorded to. ■ Recording with the metronome It is also possible to record songs with the metronome activated. This is useful when recording parts separately, or wishing to maintain correct timing throughout complex passages. Note that the standard metronome click will not be heard when the song is played back. * For more information about the instrument’s Metronome function, please refer to page 32. ■ Changing panel settings while recording In some cases, it may be desirable to make changes to the selected sound or style while recording a song. The tables below list the various functions which will and will not be remembered during recording. Panel operations remembered during recording Changes made to the sound type. (SOUND buttons etc.) Switching between dual/split modes. Panel operations NOT remembered during recording* Changes made to the reverb settings. Changes made to the effects settings. Changes made to the tempo. Changes made to the volume balance in dual/split mode. Changes made to transpose, tuning, touch, etc. * Desired effects, reverb, and tempo settings etc. should be prepared before recording a new song. 5. Exiting song recorder mode Press the FUNCTION button (EXIT), to exit the Internal Recorder and return to normal operation. 51 Internal Recorder * If a USB memory device is connected, press the FUNCTION button (INT) to select the internal song recorder.  buttons: Move selection cursor. 522 Playing a song This function is used to playback recorder songs stored in internal memory. To playback a song/part immediately after recording, start this process from step 2. 1. Entering song play mode Press the PLAY/STOP button. The Internal Recorder play screen will be shown in the LCD display. Stopped Part Recorded 2. Selecting the song/part(s) to be played back Press the  or  buttons to move the selection cursor over the song memory or part. Press the  or  buttons to change the selected song memory (1-10) or part (1, 2, or 1&2) to be played back. If a part has already been recorded, a * symbol will be shown.  buttons: Select song memory/part. Part has been recorded 3. Starting/stopping song playback Press the PLAY/STOP button. The LED indicator for the PLAY/STOP buttons will turn on, and the selected song/parts will start to play. * The selected part can be changed during song playback. * To adjust the playback tempo of the recorded song, press and hold the METRONOME button, then press the  or  buttons. Press the PLAY/STOP button again. The LED indicator for the PLAY/STOP button will turn off and the song will stop playing. 5. Exiting song play mode Press the FUNCTION button (EXIT), to exit the Internal Recorder and return to normal operation. 3 Internal Recorder Edit menu The Internal Recorder Edit menu features settings that allow the pitch of the keyboard or song to be adjusted in semi-tone steps. This menu also includes functions to delete the song, or convert the song to an audio file. ■ Internal Recorder menu Internal Recorder function Description Default setting Key Transpose Raise or lower the pitch of the keyboard in semi-tone steps. 0 (C) Song Transpose Raise or lower the pitch of the recorder song in semi-tone steps. 0 Erase Erase a part of a recorder song from memory (see page 54). – Convert to Audio Convert a recorder song to an MP3/WAV audio file (see page 55). – ■ Entering the Internal Recorder menu While the Internal Recorder play screen is shown in the LCD display: Press the FUNCTION button (EDIT). The Internal Recorder menu will be shown in the LCD display. ■ Adjusting the Internal Recorder settings/functions

After entering the Internal Recorder edit menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. ■ Exiting the Internal Recorder menu Press the FUNCTION button (BACK), to exit the Internal Recorder menu and return to normal operation.  buttons: Adjust selected setting.  buttons: Move selection cursor. 53

54Internal Recorder 4 Erasing a part/song This function is used to erase recorder parts that may have been recorded incorrectly or songs that are no longer listened to. Once a part/song has been erased from memory it cannot be recovered. 1. Selecting the Erase function After entering the Internal Recorder edit menu (see page 53): Press the  or  buttons to move the selection cursor over the Erase function. Press the FUNCTION button (ENTER) to select the Erase function. 2. Selecting the song/part to be erased Press the  or  buttons to move the selection cursor over the song memory or part. Press the  or  buttons to change the selected song memory (1-10) or part (1, 2, or 1&2) to be erased. If a part has already been recorded, a * symbol will be shown. 3. Erasing the selected song/part Press the FUNCTION button (OK) to Erase the selected song and part. A confirmation message will be shown in the LCD display, prompting to confirm or cancel the erase operation. Press the FUNCTION button (YES) to confirm the erase operation, or the FUNCTION button (NO) to cancel. ■ Erasing all recorder songs from memory Press and hold the PLAY/STOP and REC buttons, then turn the instrument’s power off/on. All recorder songs stored in memory will be erased.  buttons: Move selection cursor.  buttons: Select song memory/part.  buttons: Move selection cursor. YES: Erase NO: Cancel hold hold

5 Converting a song to an audio file This function allows recorder songs stored in internal memory to be played back and saved (converted) as an audio file to a USB device in either MP3 or WAV format. 1. Selecting the Convert to Audio function After entering the Internal Recorder edit menu (see page 53): Press the  or  buttons to move the selection cursor over the Convert to Audio function. Press the FUNCTION button (ENTER) to select the Convert to Audio function. * If a USB memory device is not connected, a prompt will be shown. 2. Selecting the song/part to be converted

Press the  or  buttons to move the selection cursor over the song memory or part. Press the  or  buttons to change the selected song memory (1-10) or part (1, 2, or 1&2) to be converted. If a part has already been recorded, a * symbol will be shown. Press the FUNCTION button (NEXT) to continue. 3. Selecting the audio file format Press the  or  buttons to select the desired file format for the converted song. It is also possible to adjust the recording gain at this stage. * For more information about the instrument’s audio recorder gain setting, please refer to page 56. 4. Starting the conversion Press the PLAY/STOP button, or a key on the keyboard. The LED indicator for the PLAY/STOP and REC buttons will turn on, the selected song will play, and the convert to audio process will start. * Notes played on the keyboard will also be recorded to the audio file. ■ Naming and saving the converted audio file  buttons: Select song memory/part.  buttons: Move selection cursor.  buttons: Select audio recorder format.

Please follow the ‘Recording an MP3/WAV audio file’ instructions on pages 56~57. from step 4.  buttons: Move selection cursor. 55 56USB Recorder 1 Recording an MP3/WAV audio file The CN39 digital piano is also capable of recording performances as digital audio – saving the data to a USB memory device in either MP3 or WAV format. This useful function allows professional quality recordings to be produced directly on the instrument – without the need for additional sound equipment – then emailed to friends and family, listened to away from the instrument, or edited and remixed further using an audio workstation. ■ Audio Recorder format specifications Audio format Specifications Bitrate MP3 44.1 kHz, 16 bit, Stereo 256 kbit/s (fixed) WAV 44.1 kHz, 16 bit, Stereo 1,411 kbit/s (uncompressed) MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson. MP3 codec is Copyright (c) 1995-2007, SPIRIT. 1. Entering USB recorder mode Connect a USB memory device to the USB port. Press the REC button. The LED indicator for the REC button will start to flash, and the USB Recorder format screen will be shown in the LCD display. 2. Selecting the USB recorder file format Press the  or  buttons to select the desired USB recorder audio file format (WAV or MP3). * MP3 audio files require less storage space than WAV audio files. * A 1 GB USB memory device can store over 12 hours of MP3 audio data. ■ Adjusting the recording volume (Gain) Press the FUNCTION button (GAIN). The gain adjustment screen and recording level meter will be shown in the LCD display. Press the  or  buttons to adjust the recorder gain setting. * To reset the gain setting to the default level, press the  and  buttons simultaneously.  buttons: Select audio recorder format. * The gain setting can be adjusted within the range of 0 dB~+15 dB. * Exercise caution when increasing the gain setting, as higher levels may result in distorted recordings.

3. Starting the USB recorder Press a key on the keyboard, or the PLAY/STOP button. The LED indicators for the REC and PLAY/STOP buttons will turn on, and recording will start. The current recording time will also be shown in the LCD display. Recording 4. Stopping the USB recorder, saving the file Press the PLAY/STOP button. The LED indicators for the PLAY/STOP and REC buttons will turn off, and recording will stop A confirmation message will be shown in the LCD display, prompting to confirm or cancel the save operation. Press the FUNCTION button (YES) to confirm the save operation, or the FUNCTION button (NO) to cancel. 5. Naming the recorded audio file, confirming save After confirming the save operation: Press the  or  buttons to cycle through the alphanumeric characters, and the  or  buttons to move the cursor. Press the FUNCTION button (OK) to confirm the save operation, or the FUNCTION button (BACK) to cancel. The recorded audio file will be saved with the specified name. or  buttons: Move selection cursor. After a few seconds, the USB Recorder play screen will be shown in the LCD display, indicating that the audio is ready for playback. To play back the recorded audio file, please refer to the ‘Playing an MP3/WAV audio file’ instructions on page 58. Time * Pressing the PLAY/STOP button allows a rest period or empty bar to be inserted at the beginning of the song. * ‘Audio-000’ will be used as the default name for the recorded audio * The recorded audio file will be saved in the root folder of the USB memory device. It is not possible to save the file in a different folder.

* Press the METRONOME button before or during the recording to turn on the metronome. The metronome ‘click’ sound will not be recorded, however drum patterns will be recorded. YES: Erase NO: Cancel  buttons: Select character. OK: Save BACK: Cancel files, with the number increasing automatically. 57 58USB Recorder 2 Playing an MP3/WAV audio file The CN39 digital piano is also capable of playing MP3 and WAV audio files stored on a USB memory device directly through the instrument’s speaker system. This function is particularly useful when attempting to learn the chords or melody to a new piece, or to simply play along with one’s favorite song. ■ Audio Player supported format specifications Audio format Specifications Bitrate MP3 32 kHz/44.1 kHz/48 kHz, Mono/Stereo 8-320 kbit/s (fixed & variable) WAV 32 kHz/44.1 kHz/48 kHz, Mono/Stereo, 16 bit - MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson. MP3 codec is Copyright (c) 1995-2007, SPIRIT. ■ Preparing the USB memory device First, prepare a selection of MP3 or WAV audio files, copying the data to a USB memory device. * USB devices should be formatted to use the ‘FAT’ or ‘FAT32’ filesystems. Please refer to page 136 for more information. 1. Entering USB playback mode Connect a USB memory device to the USB port. Press the PLAY/STOP button. The LED indicator for the the PLAY/STOP button will turn on, and the Song Browser screen will be shown in the LCD display. ■ Song Browser screen The Song Browser screen provides a listing of relevant files and folders stored on the connected USB device. The icon is used to represent an MP3/WAV audio file. The icon is used to represent a folder. The icon is used to represent the current/previous folder. An example of a typical file/folder listing screen is shown below. Please note that the visible screen height has been extended for the purpose of this illustration. Current/previous folder Folders Files  buttons: Move selection cursor. FUNCTION button: Select file/enter folder. * Files and folders will be listed in alphabetical order, with folders shown at the top of the screen. * When the USB Recorder play function is selected, only MP3, WAV, MID, and KSO files will be shown in the Song Browser screen. * The LCD display is capable of showing filenames with a maximum length of 12 characters (+3 character suffix). Filenames longer than 12 characters will be truncated automatically. 2. Selecting an audio file Press the  or  buttons to move the selection cursor, then press the FUNCTION button (SELECT) to select the audio file. The USB Recorder play screen will be shown in the LCD display. 3. Playing the selected audio file Press the PLAY/STOP button. The selected audio file will start to play, and information about the file will be shown in the LCD display. Audio file, artist/song Playback volume Playing * position If the selected audio file contains embedded metadata (e.g. ID3 tags) such as artist name and song title, this information will be also be shown beside the filename.■ Controlling audio file playback While the audio file is playing: Press the PLAY/STOP button to pause and resume playback. Press the  or  buttons to rewind or advance the playing position of the audio file. Press the  or  buttons to adjust the playback volume of the audio file.  buttons: * The playback volume can be adjusted within the range of 1~100. Adjust playback volume. Press the FUNCTION button (A-B) twice to set the start and end points of the A-B loop. * Pressing the A-B button for a third time will turn off the loop. ■ USB Recorder Edit menu The USB Recorder Edit menu allows the playback mode (Single, 1-Repeat, All-Repeat, Random) to be changed, and the pitch of the keyboard to be transposed in semi-tone steps. Please refer to page 64 for more information. ■ Overdub function The Overdub function allows the sound of the CN39 to be recorded (overdubbed) to an existing MP3 or WAV audio file. Please refer to page 66 for more information. 4. Exiting USB playback mode Press the FUNCTION button (BACK) to exit USB playback mode and return to normal operation.  buttons: Rewind/advance playing position. * There may be a noticeable difference in volume between audio file playback and the CN39 keyboard sound. When playing back audio data, please adjust the volume of the audio file as desired. 59 60USB Recorder 3 Recording a MIDI song file In addition to MP3 and WAV audio files, the CN39 digital piano is also capable of recording 16 track SMF (Standard MIDI File) format songs directly to a USB memory device. This useful function allows multi-track performances to be created one part at a time, without the need for additional recording devices. ■ MIDI Song Recorder format specifications Song format Specifications MID Format 0 1. Entering USB recorder mode Connect a USB memory device to the USB port. Press the REC button. The LED indicator for the REC button will start to flash, and the USB Recorder format screen will be shown in the LCD display. 2. Selecting the MIDI song file format Press the  or  buttons to select the MIDI song format. An additional ‘Part’ setting will be shown in the LCD display. 3. Selecting the part (track) to be recorded Press the  button to select the ‘Part’ setting, then press the  or  buttons to select the part (track) to be recorded. * The Part setting can be set to 1~16 or MIDI. * An asterisk (*) symbol will be shown beside the part number to indicate that the part has been recording and contains song data. * Unlike the internal song recorder, MIDI songs do not allow the sound of a part to be changed during recording. It is therefore necessary to select the desired sound before recording each part. * It is also possible to re-record/edit to an existing MIDI song stored on a USB memory device. Please refer to the ‘Recording to an existing MIDI song file’ instructions on page 67.  buttons: Select the MIDI song format.  buttons: Select the Part to record. * Part 10 is reserved as a drum track. When Part 10 is selected, a drum set sound will be selected automatically. * When the Part is set to MIDI, all data received from the MIDI IN or USB MIDI connectors will be recorded on Parts 1~16, according to the MIDI channel.

4. Starting the USB recorder Press a key on the keyboard, or the PLAY/STOP button. The LED indicators for the REC and PLAY/STOP buttons will turn on, and recording will start. The current recording time will also be shown in the LCD display. Recording 5. Stopping the USB recorder, saving the file Press the PLAY/STOP button. The LED indicators for the PLAY/STOP and REC buttons will turn off, and recording will stop A confirmation message will be shown in the LCD display, prompting to confirm or cancel the save operation. Press the FUNCTION button (YES) to confirm the save operation, or the FUNCTION button (NO) to cancel. 6. Naming the recorded MIDI song file, confirming save After confirming the save operation: Press the  or  buttons to cycle through the alphanumeric characters, and the  or  buttons to move the cursor. Press the FUNCTION button (OK) to confirm the save operation, or the FUNCTION button (BACK) to cancel. The recorded MIDI song file will be saved with the specified name. or YES: Save NO: Cancel  buttons: Move selection cursor. OK: Save BACK: Cancel To play back the recorded MIDI song file, please refer to the ‘Playing a MIDI song file’ instructions on page 62. To continue recording additional parts (tracks) to the MIDI song file, please refer to the ‘Recording to an existing MIDI song file’ instructions on page 67. Time * Pressing the PLAY/STOP button allows a rest period or empty bar to be inserted at the beginning of the song. * ‘Song-000’ will be used as the default name for the recorded MIDI * The recorded MIDI song file will be saved in the root folder of the USB memory device. It is not possible to save the file in a different folder.

* Press the METRONOME button before or during the recording to turn on the metronome. The metronome ‘click’ sound and drum patterns will not be recorded to the MIDI song.  buttons: Select character. song file, with the number increasing automatically. 61 USB Recorder * Files and folders will be listed in alphabetical order, with folders shown at the top of the screen. * When the USB Recorder play function is selected, MP3, WAV, MID, and KSO files will be shown in the Song Browser screen. * The LCD display is capable of showing filenames with a maximum length of 12 characters (+3 character suffix). Filenames longer than 12 characters will be truncated automatically. 624 Playing a MIDI song file The CN39 digital piano also supports the playback of Standard MIDI File (SMF) files and CN39 recorder songs stored on a USB memory device, allowing a vast selection of widely accessible music to be heard through the instrument’s exquisite Progressive Harmonic Imaging sound engine. ■ Song Player supported format specifications Song format Specifications MID Format 0, Format 1 KS0 Kawai Song file ■ Preparing the USB memory device First, prepare a selection of MIDI (SMF) song files, copying the data to a USB memory device. * USB devices should be formatted to use the ‘FAT’ or ‘FAT32’ filesystems. Please refer to page 136 for more information. 1. Entering USB playback mode Connect a USB memory device to the USB port. Press the PLAY/STOP button. The LED indicator for the the PLAY/STOP button will turn on, and the Song Browser screen will be shown in the LCD display. ■ Song Browser screen The Song Browser screen provides a listing of relevant files and folders stored on the connected USB device. The icon is used to represent a MIDI song file. The icon is used to represent a folder. The icon is used to represent the current/previous folder. An example of a typical file/folder listing screen is shown below. Please note that the visible screen height has been extended for the purpose of this illustration. Current/previous folder  buttons: FUNCTION button: Move selection cursor. Select file/enter folder. Folders Files 2. Selecting a MIDI file Press the  or  buttons to move the selection cursor, then press the FUNCTION button (SELECT) to select the MIDI file. The USB Recorder play screen will be shown in the LCD display. 3. Playing the selected MIDI file Press the PLAY/STOP button. The selected MIDI file will start to play, and information about the file will be shown in the LCD display.

MIDI file, artist/song Playback volume Playing position ■ Controlling MIDI file playback While the MIDI file is playing: Press the PLAY/STOP button to pause and resume playback. Press the  or  buttons to rewind or advance the playing position of the MIDI file. Press the  or  buttons to adjust the playback volume of the MIDI file. * The playback volume can be adjusted within the range of 1~100 Press the FUNCTION button (A-B) twice to set the start and end points of the A-B loop. * Pressing the A-B button for a third time will turn off the loop. ■ USB Recorder Edit menu  buttons: Rewind/advance playing position.  buttons: Adjust playback volume.

The USB Recorder Edit menu allows the playback mode to be changed, the tempo and part playback of the MIDI song to be adjusted, and the pitch of the keyboard or song to be transposed in semi-tone steps. Please refer to page 64 for more information. ■ Convert MIDI to Audio function The Convert MIDI to Audio function allows MIDI files or CN39 recorder songs stored on a USB memory device to be converted to MP3/WAV audio files. Please refer to page 65 for more information. ■ Exiting USB playback mode Press the FUNCTION button (BACK) to exit USB playback mode and return to normal operation. 63 USB Recorder ■ Adjusting the USB Recorder settings After entering the USB Recorder menu: Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously. ■ Adjusting the Song Part setting After entering the USB Recorder menu: Press the FUNCTION button (PART) to enter the part select screen. * The PART button will only be shown when a MIDI song file is loaded. Press the  or  buttons to move the selection cursor over the desired part. Press the  or  buttons to change the part setting. 645 USB Recorder Edit menu The USB Recorder Edit menu allows the playback mode of the audio/MIDI file to be changed to one of four types. This menu also features settings to adjust the MIDI song playback tempo, to transpose the pitch of the keyboard or MIDI song in semi-tone steps, and to control the part playback of a MIDI song. ■ USB Recorder menu USB Recorder function Description Default setting Play Mode Change the audio/MIDI file playback mode (see below). Single Tempo Adjust the playback tempo of the MIDI song in beats per minute (BPM). – Key Transpose Raise or lower the pitch of the keyboard in semi-tone steps. 0 (C) Song Transpose Raise or lower the pitch of the recorder/MIDI song in semi-tone steps. 0 Song Part Play/mute the 16 individual parts (tracks) of a MIDI song. Play all parts * Tempo, Song Transpose, and Song Part settings will not be shown when an audio file is selected. ■ Play Mode settings Play Mode setting Description Single The selected audio/MIDI file will be played once. 1-Repeat The selected audio/MIDI file will be repeated. All-Repeat All audio/MIDI files in the current folder will be played repeatedly. Random All audio/MIDI files in the current folder will be played in random order. ■ Entering the USB Recorder menu While the USB Recorder screen is shown in the LCD display: Press the FUNCTION button (EDIT). The USB Recorder menu will be shown in the LCD display. 6 Converting a MIDI song file to an MP3/WAV audio file This function allows MIDI files or CN39 recorder songs stored on a USB memory device to be played back and saved (converted) as an audio file (to the USB device) in either MP3 or WAV format. 1. Selecting the MIDI song to be converted While the Song Browser Player screen is shown in the LCD display: Press the  or  buttons to move the selection cursor over the desired MIDI file, then press the REC button. The LED indicator for the REC button will start to flash, and the Convert MIDI to Audio screen will be shown in the LCD display. 2. Selecting the audio file format

With the Format setting selected, press the  or  buttons to select the desired USB recorder audio file format (WAV or MP3). It is also possible to adjust the recording gain at this stage. * For more information about the instrument’s audio recorder gain setting, please refer to page 56. * It is also possible to record a new song directly to the USB device (i.e. not convert the previously selected song to an audio file) by changing the Mode setting to ‘New Song’. 3. Starting the conversion Press the PLAY/STOP button, or a key on the keyboard. The LED indicator for the PLAY/STOP and REC buttons will turn on, the selected song will play, and the convert to audio process will start. * Notes played on the keyboard will also be recorded to the audio file. When the end of the song is reached, the save confirmation screen will be shown in the LCD display. ■ Naming and saving the converted audio file  buttons: Select audio recorder format.

Please follow the ‘Recording an MP3/WAV audio file’ instructions on pages 56~57. from step 4. 65 USB Recorder * The playback volume of the selected audio file will automatically be set to 100, in order to prevent a distorted recording. 667 Overdubbing an MP3/WAV audio file This function allows the sound of the CN39 to be recorded (overdubbed) to an existing MP3 or WAV audio file stored on a USB memory device. * This function records/overdubs to a copy of the selected file – the original audio file will not be modified. 1. Selecting the audio file to be overdubbed While the Song Browser Player screen is shown in the LCD display: Press the  or  buttons to move the selection cursor over the desired MP3/WAV file, then press the REC button. The LED indicator for the REC button will start to flash, and the Overdubbing screen will be shown in the LCD display. 2. Selecting the audio file format With the Format setting selected, press the  or  buttons to select the desired USB recorder audio file format (WAV or MP3). * It is also possible to record a new audio file directly to the USB device (i.e. not overdub the previously selected audio file) by changing the Mode setting to ‘New Song’. 3. Starting the recording/overdubbing Press the PLAY/STOP button, or a key on the keyboard. The LED indicator for the PLAY/STOP and REC buttons will turn on, the selected audio file will play, and the recording/ overdubbing process will start. Notes played on the keyboard will be recorded to the audio file. or When the PLAY/STOP button is pressed, the save confirmation screen will be shown in the LCD display. ■ Naming and saving the overdubbed audio file Please follow the ‘Recording an MP3/WAV audio file’ instructions on pages 56~57. from step 4.  buttons: Select audio recorder format. 8 Recording to an existing MIDI song file This function allows the parts (tracks) of a MIDI song file to be re-recorded, or for new parts to be added. 1. Selecting the MIDI song file to be re-recorded/added to While the Song Browser Player screen is shown in the LCD display: Press the  or  buttons to move the selection cursor over the desired MIDI file, then press the REC button. The LED indicator for the REC button will start to flash, and the ‘16 Track Record’ mode will be selected automatically. * It is also possible to record a new MIDI song file to the USB device (i.e. not re-record the selected song file) by changing the Mode to ‘New Song’. An additional ‘Part’ setting will be shown in the LCD display. 2. Selecting the part (track) to be recorded Press the  button to select the ‘Part’ setting, then press the  buttons:  or  buttons to select the part (track) to be recorded. Select the Part to record. * An asterisk (*) symbol will be shown beside the part number to * Please refer to page 60 for information regarding the restrictions indicate that the part has been recording and contains song data. that apply when recording to MIDI song files.3. Starting the recording Press the PLAY/STOP button, or a key on the keyboard. The LED indicator for the PLAY/STOP and REC buttons will turn or on, the selected MIDI song file will play, and the recording process will start. Notes played on the keyboard will be recorded to the selected MIDI song file and part. When the PLAY/STOP button is pressed, the save confirmation screen will be shown in the LCD display. ■ Naming and saving the recored MIDI song file Please follow the ‘Recording a MIDI song file’ instructions on page 60~61 from step 5. 67 68Function menus The Function menus contain a variety of options to adjust the CN39 digital piano’s operation and sound. Settings are grouped by category, providing convenient access to relevant controls. Once adjusted, settings can be stored to one of the instrument’s 16 registration memories, or selected as the default power-on settings with the Startup Setting function. * For more information about the Startup Setting function, please refer to page 79. ■ Entering the Function menus While the normal playing mode screen is shown in the LCD display: Press the FUNCTION button (MENU). The Function menus will be shown in the LCD display. Press the  or  buttons to cycle through the different menus. Press the FUNCTION button (ENTER) to enter the selected Function menu.  buttons: FUNCTION button: Move selection cursor. Select function. ■ Exiting the Function menus Press the FUNCTION button (EXIT) to exit the Function menus and return to normal operation. ■ Overview of Function menus 1. Basic Settings 4. MIDI Settings * Key Transpose, Song Transpose, Tone Control, Speaker Volume, MIDI Channel, Send Program Change No., Local Control, Tuning, Damper Hold, Split, Four Hands, Startup Setting, Transmit Program Change No., Multi-timbral Mode, Channel Mute Factory Reset, Auto Display Off, Auto Power Off 5. USB Functions 2. Virtual Technician Settings Load Song, Load Registration All, Load Registration Single, Touch Curve, Voicing, Damper Resonance, Damper Noise, Load Startup Setting, Save Internal Song, Save SMF Song, String Resonance, Undamped String Resonance, Cabinet Resonance, Save Registration All, Save Registration Single, Save Startup Setting, Key-off Effect, Fallback Noise, Hammer Delay, Topboard Simulation, Rename File, Delete File, Format USB Decay Time, Minimum Touch, Stretch Tuning, Temperament, Temperament Key, Key Volume, Half-Pedal Adjust, Soft Pedal Depth 6. Bluetooth Settings Bluetooth Audio, Bluetooth Audio Volume, Bluetooth MIDI 3. Phones Settings SHS Mode, Phones Type, Phones Volume * For information regarding MIDI functions and settings, please download the supplementary PDF manual from the Kawai Japan website: kawai-global.com/support/manual/ Basic Settings The Basic Settings menu contains settings to adjust the pitch, tuning, and general sound of the instrument. This menu also allows favourite panel settings to be stored, or reset back to the original factory configuration. ■ Basic Settings No. Setting Description Default setting 1 Key Transpose Raise or lower the pitch of the keyboard in semi-tone steps. 0 (C) 2 Song Transpose Raise or lower the pitch of the recorder/MIDI song in semi-tone steps. 0 3 Tone Control Change the EQ settings of the instrument’s sound. Off 4 Speaker Volume Change the maximum volume level of the speaker output. Normal 5 Tuning Raise or lower the pitch of the instrument in 0.5 Hz steps. 440.0 Hz 6 Damper Hold Change the effect of pressing the sustain pedal on organ, string, etc. sounds. Off 7 Split Enable the ‘Split Mode’ function. Off 8 Four Hands Enable the ‘Four Hands Mode’ function. Off 9 Startup Setting Store current panel settings as the default (power-on) configuration. - 10 Factory Reset Restore all panel settings to the original factory configuration. - 11 Auto Display Off Enable/disable the instrument’s Auto Display Off function. 5 min. 12 Auto Power Off Enable/disable the instrument’s Auto Power Off energy saving function. - * Default settings will be shown in the first LCD display illustration (i.e. Step 1) for each setting explanation below. ■ Entering the Basic Settings menu While the normal playing mode screen is shown in the LCD display: Press the FUNCTION button (MENU). The Function menus will be shown in the LCD display. Press the FUNCTION button (ENTER) again to enter the Basic Settings menu. ■ Selecting and adjusting the desired setting After entering the Basic Settings menu:  buttons: Adjust selected setting. Press the  or  buttons to move the selection cursor over the desired setting. Press the  or  buttons to adjust the selected setting. * To reset the current setting to the default value, press the  and  buttons simultaneously.  buttons: Move selection cursor. 69 701 Key Transpose The Key Transpose setting allows the pitch of the CN39 digital piano keyboard to be raised or lowered in semi-tone steps. This is particularly useful when accompanying instruments tuned for different keys, or when a song learned in one key must be played in another key. When transposed, the song can be played in the original key, yet heard in a different key. 1. Selecting the Key Transpose setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Key Transpose setting. 2. Adjusting the Key Transpose value Press the  or  buttons to increase or decrease the value of the Key Transpose setting. * The keyboard pitch can be raised or lowered by up to 12 semi-tones. * To reset the Key Transpose setting to the default value, press the  and  buttons simultaneously. * Any changes made to the Key Transpose setting will remain until the power is turned off. * Preferred Key Transpose settings can be stored to a Registration Memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. ■ Current Transpose state If the Key Transpose setting is set to a value other than 0 (C), the transpose icon and transpose value will appear at the top of the display. 3. Exiting the Key Transpose setting Press the FUNCTION button (BACK) to exit the Key Transpose setting and return to the Function Menus screen. Basic Settings Transpose enabled 2 Song Transpose The Song Transpose setting allows the pitch of MIDI files or CN39 recorder songs stored on a USB memory device to be raised or lowered in semi-tone steps when played back. 1. Selecting the Song Transpose setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Song Transpose setting. 2. Adjusting the Song Transpose value Press the  or  buttons to increase or decrease the value of the Song Transpose setting. * The song pitch can be raised or lowered by up to 12 semi-tones. * To reset the Song Transpose setting to the default value, press the  and  buttons simultaneously. * Any changes made to the Song Transpose setting will remain until the power is turned off. * Song Transpose settings cannot be stored to Registration or Startup Setting memory. 3. Exiting the Song Transpose setting Press the FUNCTION button (BACK) to exit the Song Transpose setting and return to the Function Menus screen. 71 723 Tone Control The Tone Control setting allows the overall sound character of the CN39 digital piano to be adjusted to provide the best sound quality within the area that the instrument is located. There are eight different preset EQ settings available, with an additional ‘User’ setting allowing finer control over the different frequency bands. ■ Tone Control setting Tone Control type Description Flat (default) Tone control adjustment is not applied. Brilliance Adjusts the overall brightness of the sound, independently of the Virtual Technician ‘Voicing’ parameter. Bass Boost Emphasises low-range frequencies, creating a deeper sound. Bass Cut Reduces low-range frequencies, creating a clearer sound. Mid Boost Emphasises mid-range frequencies, creating a harder sound. Loudness Emphasises frequencies to retain the instrument’s sound character when playing at low volume levels. Bright Emphasises high-range frequencies, creating a brighter sound. Mellow Reduces high-range frequencies, creating a softer sound. User Allows the low, mid, and high-range frequency bands to be adjusted separately. 1. Selecting the Tone Control setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Tone Control setting. 2. Changing the Tone Control type Press the  or  buttons to cycle through the different Tone Control types. * To reset the Tone Control setting to the default type, press the  and  buttons simultaneously. * Any changes made to the Tone Control setting will remain until the power is turned off. * Preferred Tone Control settings can be stored to a Registration Memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 3. Exiting the Tone Control setting Press the FUNCTION button (BACK) to exit the Tone Control setting and return to the Function Menus screen. ■ Adjusting the Brilliance level When the Brilliance tone control type is selected: Press the FUNCTION button (EDIT), then press the  or  buttons to increase/decrease the value of the Brilliance setting. * The Brilliance value can be adjusted within the range of –10~+10. Press the FUNCTION button (BACK) to exit the Brilliance setting and return to the Tone Control setting. Basic Settings  buttons: Adjust Brilliance setting. User Tone Control The User Tone Control option allows finer control over the instrument’s sound character, allowing the volume of four frequency bands to be adjusted individually. It is also possible to adjust the frequency range of the mid-low and mid-high frequency bands. ■ User Tone Control setting No. User Tone Control Description 1 Low Adjusts the volume of the low range frequency band (20~100 Hz). 2 Mid-low Frequency Adjusts the frequency of the mid-low band (200~4000 Hz). Mid-low dB Adjusts the volume of the mid-low range frequency band. 3 Mid-high Frequency Adjusts the frequency of the mid-high band (200~4000 Hz). Mid-high dB Adjusts the volume of the mid-high range frequency band. 4 High Adjusts the volume of the high range frequency band (5000~8000 Hz). 1. Selecting the User Tone Control setting After selecting the Tone Control setting (page 72): Press the  or  buttons to select the User Tone Control type, then press the FUNCTION button (EDIT). The User Tone Control screen will be shown in the LCD display. 2. Selecting and adjusting the User Tone Control settings Press the  or  buttons to select the User Tone Control setting. Press the  or  buttons to increase or decrease the value of the selected User Tone Control setting. * Each User Tone Control band can be adjusted within the range of –6 dB~+6 dB. * To reset the User Tone Control setting to the default type, press the  and  buttons simultaneously. * Any changes made to the User Tone Control setting will remain until the power is turned off. * Preferred User Tone Control settings can be stored to the Startup Setting memory for convenient recall. Please refer to page 79 for more information. 3. Exiting the User Tone Control setting Press the FUNCTION button (BACK) to exit the User Tone Control setting and return to the Tone Control setting. 73 744 Speaker Volume The Speaker Volume setting allows the maximum volume level of the CN39 digital piano’s speaker output to be reduced, providing finer adjustment control over the master volume. This setting can also function as a volume limiter, preventing the instrument from being played too loudly in the home or classroom etc. * This setting does not affect the headphones volume. ■ Speaker Volume setting Speaker Volume Description Normal (default) The instrument’s speakers will output sound at the normal volume level. Low The instrument’s speakers will output sound at a reduced volume level. 1. Selecting the Speaker Volume setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Speaker Volume setting. 2. Changing the Speaker Volume type Press the  or  buttons to alternate between ‘Normal’ and ‘Low’ Speaker Volume settings. * To reset the Speaker Volume setting to the default setting, press the  and  buttons simultaneously. * Any changes made to the Speaker Volume setting will remain until the power is turned off. * Preferred Speaker Volume settings can be stored to the Startup Setting memory for convenient recall. Please refer to page 79 for more information. 3. Exiting the Speaker Volume setting Press the FUNCTION button (BACK) to exit the Speaker Volume setting and return to the Function Menus screen. Basic Settings 5 Tuning The Tuning setting allows the overall pitch of the CN39 digital piano to be raised and lowered in 0.5 Hz steps, and may therefore prove useful when playing with other instruments. 1. Selecting the Tuning setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Tuning setting. 2. Adjusting the Tuning value Press the  or  buttons to increase or decrease the value of the Tuning setting. * The Tuning value can be adjusted within the range of 427.0~453.0 Hz. * To reset the Tuning setting to the default value, press the  and  buttons simultaneously. * Any changes made to the Tuning setting will remain until the power is turned off. * Preferred Tuning settings can be stored to a Registration Memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 3. Exiting the Tuning setting Press the FUNCTION button (BACK) to exit the Tuning setting and return to the Function Menus screen. 75 76Basic Settings 6 Damper Hold The Damper Hold setting is used to determine whether sounds such as organ or strings should be sustained continuously when the sustain (damper) pedal is pressed, or whether these sounds should decay, naturally. ■ Damper Hold setting Damper Hold Description Off (default) Organ, strings, etc. sounds will gradually decay, even while the sustain pedal is pressed. On Organ, strings, etc. sounds will be sustained continuously while the sustain pedal is pressed. 1. Selecting the Damper Hold setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Damper Hold setting. 2. Changing the Damper Hold setting Press the  or  buttons to turn the Damper Hold setting on or off. * To reset the Damper Hold setting to the default setting, press the  and  buttons simultaneously. * Any changes made to the Damper Hold setting will remain until the power is turned off. * Preferred Damper Hold settings can be stored to a Registration Memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 3. Exiting the Damper Hold setting Press the FUNCTION button (BACK) to exit the Damper Hold setting and return to the Function Menus screen. 7 Split The Split setting provides an alternative method to enabling the Split Mode function, and may prove useful in teaching environments or situations where the function should be enabled automatically every time the CN39 digital piano is turned on. When enabled, all Split Mode control operations are identical to those explained on page 22. ■ Split setting Split Description Off (default) Split Mode will be turned off by default. On Split Mode will be turned on by default. 1. Selecting the Split setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Split setting. 2. Changing the Split setting Press the  or  buttons to turn the Split setting on or off. * To reset the Split setting to the default setting, press the  and  buttons simultaneously. * When Split is turned on, the Four Hands Mode will be turned off automatically. * Any changes made to the Split setting will remain until the power is turned off. * Preferred Split settings can be stored to a Registration Memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 3. Exiting the Split setting Press the FUNCTION button (BACK) to exit the Split setting and return to the Function Menus screen. 77 788 Four Hands The Four Hands setting provides an alternative method to enabling the Four Hands Mode function, and may prove useful in teaching environments or situations where the function should be enabled automatically every time the CN39 digital piano is turned on. When enabled, all Four Hands Mode control operations are identical to those explained on page 24. ■ Four Hands setting Four Hands Description Off (default) Four Hands Mode will be turned off by default. On Four Hands Mode will be turned on by default. 1. Selecting the Four Hands setting After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Four Hands setting. 2. Changing the Four Hands setting Press the  or  buttons to turn the Four Hands setting on or off. * To reset the Four Hands setting to the default setting, press the  and  buttons simultaneously. * When Four Hands Mode is turned on, the Split function will be turned off automatically. * Any changes made to the Four Hands setting will remain until the power is turned off. * Preferred Four Hands settings can be stored to a Registration Memory for convenient recall, or to the Startup Setting memory for automatic selection when the instrument is turned on. Please refer to pages 35 and 79 for more information. 3. Exiting the Four Hands setting Press the FUNCTION button (BACK) to exit the Four Hands setting and return to the Function Menus screen. Basic Settings 9 Startup Setting The Startup Setting function allows preferred panel functions/settings to be stored in the instrument’s memory, and automatically recalled as the default settings every time the CN39 digital piano is turned on. * Startup Settings can also be saved to and loaded from USB memory devices. Please refer to pages 123/118 for more information. ■ Functions/Settings stored in the Startup Setting memory

Functions Selected sound (including primary sound for each category) Dual Mode / Split Mode / Four Hands Mode (including settings) Reverb, Effects (Type, Settings) Metronome (Beat, Tempo, Volume) Settings Basic Settings (with exceptions) Virtual Technician Settings MIDI Settings Headphone Settings

* Changes made to the Auto Display Off, Auto Power Off, and Bluetooth settings will be stored to the Startup Setting memory automatically. * For a complete listing of the settings that can be stored to Startup Setting memory, please refer to pages 140~141. 1. Selecting the Startup Setting function After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Startup Setting function. 2. Storing current settings to the Startup Setting memory Press the REC button. A confirmation message will be shown in the LCD display, and the current panel settings will be stored to the Startup Setting memory. * The Factory Reset function can be used to restore all settings to their default values. Please refer to page 80 for more information. 3. Exiting the Startup Setting function Press the FUNCTION button (BACK) to exit the Startup Setting function and return to the Function Menus screen 79 80Basic Settings 10 Factory Reset The Factory Reset function clears any settings stored using the User Memory function, restoring the CN39 digital piano to its factory default settings. * This function will not clear registration memories or recorder songs stored in internal memory. 1. Selecting the Factory Reset function After entering the Basic Settings menu (page 69): Press the  or  buttons to select the Factory Reset setting. 2. Restoring factory settings Press the REC button. A confirmation message will be shown in the LCD display, and all settings will be restored to their default values. After competition, the normal playing mode screen will be shown in the display automatically.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply