JOHN LEWIS JLBIDW917 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD JOHN LEWIS JLBIDW917 (01) PDF MANUAL


PDF Content Summary: DishwasherJLBIDW917 User Manual

Contents Safety information 3 Children and vulnerable people safety 3 General Safety 3 Safety instructions 5 Installation 5 Electrical connection 5 Water connection 5 Use 5 Service 6 Disposal 6 Installation 7 Unpacking 7 Levelling of the appliance 7 7 Fixing to the adjacent units 7 Product description 8 Beam-on-Floor 8 Control panel 9 Indicators 9 Programmes 10 Consumption values 10 Information for test institutes 11 Settings 12 Programme selection mode and user mode 12 The water softener 12 The rinse aid empty notification 13 Acoustic signals 14 DryAssist 14 Options 15 Extra dry 15 Before first use 16 The salt container 16 Filling with rinse aid 17 Daily use 18 Loading cutlery and dishes 18 Using the detergent 21 Setting and starting a programme 22 Hints and tips 23 General 23 Using salt, rinse aid and detergent 23 What to do if you want to stop using multi tablets 23 Loading the baskets 23 Before starting a programme 24 Unloading the baskets 24 Care and cleaning 25 Cleaning the filters 25 Cleaning the spray arms 26 External cleaning 26 Internal cleaning 26 Troubleshooting 27 The washing and drying results are not satisfactory 28 Product information sheet 31 Additional technical information 32 Water connection 33 Water inlet connection 33 Water drain connection 33 Electrical connection 35 Repairs - after sales service 36

2 Dishwasher User Manual Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. Children and vulnerable people safety • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. • Children between 3 and 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. • Children of less than 3 years of age should be kept away from the appliance unless continuously supervised. • Do not let children play with the appliance. • Keep detergents away from children. • Keep children and pets away from the appliance when the door is open. • Children shall not carry out cleaning and user maintenance of the appliance without supervision. General Safety • This appliance is intended to be used in household and similar applications such as: – farm houses; staff kitchen areas in shops, offices and other working environments; Dishwasher User Manual 3 – by clients in hotels, motels, bed & breakfast and other residential type environments. • Do not change the specification of this appliance. • The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (MPa) • Follow the maximum number of 9 place settings. • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. • Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. • Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. • Do not use high pressure water sprays and/or steam to clean the appliance. • If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 4 Dishwasher User Manual Safety instructions

Installation Warning! Only a qualified person must install this appliance. • Remove all the packaging. • Do not install or use a damaged appliance. • Do not use the appliance before installing it in the built-in structure due to safety manner. • Follow the installation instructions supplied with the appliance. • Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear. • Do not install or use the appliance where the temperature is less than 0 °C. • Install the appliance in a safe and suitable place that meets installation requirements. Electrical connection Warning! Risk of fire and electric shock. • The appliance must be earthed. • Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply. • Always use a correctly installed shockproof socket. • Do not use multi-plug adapters and extension cables. • Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre. • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse (UK and Ireland only). Water connection • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear. • Ensure that there are no visible water leaks during and after the first use of the appliance. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. Use • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Dishwasher detergents are dangerous. Follow the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete. Some detergent may remain on the dishes. • Do not sit or stand on the open door of the appliance. • The appliance can release hot steam if you open the door while a programme operates.

Dishwasher User Manual 5 Service • To repair the appliance contact the Authorised Service Centre. • Use original spare parts only. Disposal Warning! Risk of injury or suffocation. • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance. 6 Dishwasher User Manual

Installation Warning! • It is dangerous to alter the specifications or attempt to modify the appliance in any way. • This appliance is heavy. Care should be taken when moving it. • Care must be taken to ensure that the appliance does not stand on the electrical supply cable. • Any electrical or plumbing work required to install this appliance must be carried out by a qualified electrician or plumber. Unpacking • Remove all packaging before positioning the appliance. • Position the appliance next to a water tap and a drain. Levelling of the appliance Good levelling is essential for correct closure and sealing of the appliance door. When the appliance is correctly levelled, the door will not catch on either side of the cabinet. If the appliance door does not close correctly, loosen or tighten the adjustable feet until the level of the appliance is perfect. Caution! Carefully follow the instructions on the enclosed template for building in the appliance and fitting the furniture panel. Insert the appliance after the adjustment of the appliance level. When inserting the appliance, ensure that the water inlet and drain hoses are not kinked or squashed. During all operations that involve accessibility to internal components the appliance must be unplugged. Be sure that once the appliance has been installed, it is easily accessible for the service engineer in the event that a repair is required. Fixing to the adjacent units The appliance must be secured against tilting. Therefore make sure, that the counter it is fixed under, is suitably secured to a fixed structure (e.g. adjacent kitchen unit cabinets, wall).

Dishwasher User Manual 7

Product description 9 8 7 6 5 4 3 1 2

1. Upper spray arm 2. Lower spray arm 3. Filters 4. Rating plate 5. Salt container Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes. 6. Air vent 7. Rinse aid dispenser 8. Detergent dispenser 9. Upper basket The Beam-on-Floor is off when the appliance is deactivated. When DryAssist is activated during the drying phase, the projection on the floor may not be completely visible. To see if the cycle has ended, check the control panel.

8 Dishwasher User Manual Control panel 1 2 3 4 5

1. On/off button 2. Display 3. Delay button Indicators Indicator Description Extra dry Extra dry indicator. 4. Programme buttons 5. Indicators

Rinse aid Rinse aid indicator. It is always off while the programme operates. Salt Salt indicator. It is always off while the programme operates. Dishwasher User Manual 9

Programmes Programme Degree of soil Type of load Programme phases Options

50° Eco 1) • Normal soil • Crockery and cutlery 45°-70° Auto 2) • All • Crockery, cutlery, pots and pans 70° Intensive • Heavy soil • Crockery, cutlery, pots and pans 60° Quick 3) • Fresh soil • Crockery and cutlery • Prewash • Wash 50 °C • Rinses • Dry • Prewash • Wash from 45 °C to 70 °C • Rinses • Dry • Prewash • Wash 70 °C • Rinses • Dry • Wash 60 °C or 65 °C • Rinses • Extra dry • Extra dry • Extra dry • Extra dry

Rinse hold 4) • All • Prewash 1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil. (This is the standard programme for test institutes). 2) The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the temperature and the quantity of water, the energy consumption and the programme duration. 3) With this programme you can wash a load with fresh soil. It gives good washing results in a short time. 4) With this programme you can quickly rinse dishes to prevent remains of food to bond on dishes and odours to form in the appliance. Do not use detergent with this programme. Consumption values

Programme 1) Water (l) Energy (kWh) Duration (min)

50° Eco 9.9 0.777 227 45°-70° Auto 6 - 11 0.6 - 1.2 45 - 151 70° Intensive 13-14 1.1 - 1.3 160 - 168 60° Quick 8 0.7 30 10 Dishwasher User Manual

Programme 1) Water (l) Energy (kWh) Duration (min)

Rinse hold 4 0.1 14 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. Information for test institutes To receive the necessary information for conducting performance tests (e.g. according to EN60436), send an email to: info.test@dishwasher-production.com In your request please include the product number code (PNC) found on the rating plate. For any other questions regarding your dishwasher please refer to the service book provided with your appliance. Dishwasher User Manual 11

Settings Programme selection mode and user mode When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode. Settings available in the user mode: • The level of water softener according to the water hardness. • Activation or deactivation of the acoustic signal for the end of a programme. • Activation or deactivation of the rinse aid empty notification. • Activation or deactivation of DryAssist. As the appliance stores the saved settings, there is no need to configure it before every cycle. How to set the programme selection mode The appliance is in programme selection mode when the programme indicator 50° Eco is on and the display shows the programme duration. When you activate the appliance, usually it is in programme selection mode. However, if this does not happen, you can set the programme selection mode in the following way: Press and hold simultaneously Eco and Auto until the appliance is in programme selection mode. Water hardness How to enter user mode Make sure the appliance is in programme selection mode. To enter user mode, press and hold simultaneously Eco and Auto until the indicators Delay, Eco, Auto and Intensive flash and the display is blank. The water softener The water softener removes minerals from the water supply, which would have a negative effect on the washing results and on the appliance. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results. Softening hard water increases the consumption of water and energy as well as the programme duration. The higher the level of water softener, the higher the consumption and the longer the duration.

German degrees (°dH) French degrees (°fH) mmol / l Clarke de grees Water softener level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 12 Dishwasher User Manual

German degrees (°dH) French degrees (°fH) mmol / l Clarke de grees Water softener level

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 < 5 1 2) 1) Factory setting. 2) Do not use salt at this level.

Regardless of the type of detergent used, set the proper water hardness level to keep the salt refill indicator active. Multi-tabs containing salt are not effective enough to soften hard water. How to set the water softener level Make sure the appliance is in user mode. 1. Press Delay. • The indicators Eco, Auto and Intensive are off. • The indicator Delay still flashes. • The display shows the current setting: e.g. = level 5. 2. Press Delay repeatedly to change the setting. 3. Press on/off to confirm and save the setting. The rinse aid empty notification The rinse aid helps to dry the dishes without streaks and stains. The rinse aid is automatically released during the hot rinse phase. When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If the drying results are satisfactory while using multi-tablets only, it is possible to deactivate the notification for refilling rinse aid. However, for best drying performance, always use rinse aid. If standard detergent or multi-tablets without rinse aid are used, activate the notification to keep the rinse aid refill indicator active. How to deactivate the rinse aid empty notification Make sure the appliance is in user mode. 1. Press Eco. • The indicators Delay, Auto and Intensive are off. • The indicator Eco still flashes. • The display shows the current setting. – = rinse aid empty notification activated. – = rinse aid empty notification deactivated. 2. Press Eco to change the setting. 3. Press on/off to confirm and save the setting.

Dishwasher User Manual 13

Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals. There is also an acoustic signal that sounds when the programme is completed. By default this acoustic signal is deactivated but it is possible to activate it. How to activate the acoustic signal for the end of programme Make sure the appliance is in user mode. 1. Press Auto. • The indicators Delay, Eco and Intensive are off. • The indicator Auto still flashes. • The display shows the current setting: – = Acoustic signal off. – = Acoustic signal on. 2. Press Auto to change the setting. 3. Press on/off to confirm and save the setting. DryAssist DryAssist improves the drying results with less energy consumption. During the drying phase, the door opens automatically and remains ajar. Caution! Do not try to close the appliance door within 2 minutes after automatic opening. This can cause damage to the appliance. DryAssist is automatically activated with all programmes excluding Rinse hold (if applicable). To improve the drying performance refer to the Extra dry option or activate DryAssist. Caution! If children have access to the appliance, it is advised to deactivate DryAssist as opening the door may pose a danger. How to deactivate DryAssist Make sure the appliance is in user mode. 1. Press Intensive. • The indicators Delay, Eco and Auto are off. • The indicator Intensive still flashes. • The display shows the current setting: = DryAssist activated. 2. Press Intensive to change the setting: = DryAssist deactivated. 3. Press on/off to confirm and save the setting.

14 Dishwasher User Manual

Options Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on. If an option is not applicable to a programme, the related indicator is off or it flashes quickly for a few seconds and then goes out. Activating options can affect the water and energy consumption as well as the programme duration. Extra dry Activate this option to boost the drying performance. With Extra dry on, the duration of some programmes, water consumption and the last rinse temperature can be affected. Extra dry is a permanent option for all programmes other than 50° Eco and need not to be selected at every cycle. In the other programmes the setting of Extra dry is permanent and it is automatically used in next cycles. This configuration can be changed at any time. Every time 50° Eco is activated, Extra dry is off and needs to be chosen manually. How to activate Extra dry Press simultaneously Intensive and Quick. The indicator Extra dry is on. The display shows the updated programme duration.

Dishwasher User Manual 15

Before first use 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not put dishes in the baskets. After starting the programme, the appliance recharges the resin in the water softener for up to 5 minutes. The washing phase starts only after this procedure is complete. The procedure is repeated periodically. The salt container Caution! Use rough salt designed for dishwashers only. Fine salt increases the risk of corrosion. The salt is used to recharge the resin in the water softener and to assure good washing results in daily use. How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (only for the first time). 3. Fill the salt container with 1 kg of salt (until it is full). 4. Carefully shake the funnel by its handle to get the last granules inside. 5. Remove the salt around the opening of the salt container. 6. Turn the cap of the salt container clockwise to close the salt container. Caution! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion.

16 Dishwasher User Manual

Filling with rinse aid A B M AX 3 21 4 + - Caution! Use branded rinse aid for dishwashers only. Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance. Rinse aid ensures thorough rinsing, and spot and streak free drying. Rinse aid is automatically added during the last rinse. C D

1. Press the release button (D) to open the lid (C) of the rinse aid dispenser. 2. Fill the rinse aid dispenser (A) with rinse aid. The maximum level for filling is indicated by 'MAX'. 3. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next washing programme. 4. Close the rinse aid dispenser. Press the lid until it locks into position. Dishwasher User Manual 17 Daily use 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and the degree of soil. Loading cutlery and dishes Warning! Always close the appliance door after loading the baskets. An open door can be a hazard. Caution! Always ensure that the spray arms can rotate freely before you close the appliance door and start the programme. The lower basket The lower basket is designed to take pots, pans, lids, dishes, salad bowls and cutlery. Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely. 18 Dishwasher User Manual

The cutlery basket Warning! Knives with long blades, stored in an upright position, are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards Mix spoons with other cutlery to prevent them from sticking together. For best results we recommend you use the cutlery grid. If the size and dimensions of the cutlery do not allow the use of the grid, this can be easily removed. The upper basket Arrange items on and underneath the cup racks so that water can reach all surfaces.

Dishwasher User Manual 19

Glasses with long stems can be placed upside down in the cup racks. For taller items, the cup racks can be folded upwards. Caution! Ensure that the spray arms can rotate freely before you close the appliance door. Adjusting the height of the upper basket Caution! Never lift or lower the basket on one side only. To load very large plates move the upper basket to the higher position.

20 Dishwasher User Manual

24 cm 27 cm 20 cm 31 cm Moving the upper basket to the higher position 1. Pull out the basket until it stops. 2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable. Moving back the upper basket to the lower position 1. Pull out the basket until it stops. 2. Carefully lift both sides upwards and then allow the mechanism to drop back down slowly, keeping hold of it. Using the detergent A B 30 20 C Caution! Only use detergent specifically designed for dishwashers. 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. Close the lid. Make sure that the release button locks into position.

Dishwasher User Manual 21

Setting and starting a programme The Auto off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme. • After 5 minutes if the programme has not started. Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press the button related to the chosen programme. The display shows the programme duration. 4. Set the applicable options. 5. Close the appliance door to start the programme. Starting a programme with delay start 1. Set a programme. 2. Press Delay start again and again until the display shows the delay time you want to set (from 1 to 24 hours). The delay indicator comes on. 3. Close the appliance door to start the countdown. While a countdown is running it is possible to increase the delay time but not to change the selection of the programme and options. When the countdown is completed, the programme starts. Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by DryAssist function. Do not try to close the appliance door within 2 minutes after DryAssist automatically opens it, as this may cause damage to the appliance. If, afterwards, the door is closed for another 3 minutes, the running programme ends. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Press and hold simultaneously Eco and Auto until the appliance is in programme selection mode. Cancelling the programme Press and hold simultaneously Eco and Auto until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. End of the programme When the programme is completed the display shows 0:00. All buttons are inactive except for the on/off button. 1. Press the on/off button or wait for the Auto off function to automatically deactivate the appliance. If you open the door before the activation of Auto off, the appliance is automatically deactivated. 2. Close the water tap.

22 Dishwasher User Manual

Hints and tips General Follow the hints below to ensure optimal cleaning and drying results in daily use and to help you protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, select a programme with a prewash phase. • Always use the whole space of the baskets. • Make sure that items in the baskets do not touch or cover each other. Only then can the water completely reach and wash the dishes. • You can use dishwasher detergent, rinse aid and salt separately or you can use the multi tablets (e.g. ''All in 1''). Follow the instructions on the packaging. • Select a programme according to the type of load and the degree of soil. 50° Eco offers the most efficient use of water and energy consumption. Using salt, rinse aid and detergent • Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance. • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. • At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose. • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of rinse aid. 6. Activate the rinse aid empty notification. Loading the baskets • Only use the appliance to wash items that are dishwasher-safe. • Do not put in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not put in the appliance items that can absorb water (sponges, household cloths). • Remove remaining food from the items. • Make soft the remaining burned food on the items. • Put hollow items (cups, glasses and pans) with the opening down. • Make sure that cutlery and dishes do not bond together. Mix spoons with other cutlery. • Make sure that glasses do not touch other glasses. • Put small items in the cutlery basket. • Put light items in the upper basket. Make sure that the items do not move.

Dishwasher User Manual 23 • Make sure that the spray arm can move freely before you start a programme. Before starting a programme Before you start the selected programme, make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is enough salt and rinse aid (unless you use multi-tablets). • The arrangement of the items in the baskets is correct. • The programme is suitable to the type of load and the degree of soil. • The correct quantity of detergent is used. Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. 2. First remove items from the lower basket, then from the upper basket. After the programme is completed, water can still remain on the inside surfaces of the appliance. 24 Dishwasher User Manual

Care and cleaning Warning! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. Cleaning the filters The filter system is made of 3 parts. C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides.

Dishwasher User Manual 25

7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. Caution! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. External cleaning • Clean the appliance with a moist soft cloth. • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. Internal cleaning • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers. Follow carefully the instructions on the packaging of the product.

26 Dishwasher User Manual

Troubleshooting If the appliance does not start or it stops during operation. Before you contact an Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. Warning! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.

Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The programme does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes.

The appliance does not fill with wa ter. The display shows or . The appliance does not drain the water. The display shows . The anti-flood device is on. The display shows . • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. • Make sure that the sink spigot is not clogged. • Make sure that the filter in the outlet hose is not clogged. • Make sure that the interior filter system is not clogged. • Make sure that the drain hose has no kinks or bends. • Close the water tap and contact an Authorised Service Centre.

Dishwasher User Manual 27 Problem and alarm code Possible cause and solution

The appliance stops and starts more times during operation. • It is normal. It provides optimal cleaning results and energy savings.

The programme lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown.

The remaining time in the display increases and skips nearly to the end of programme time. • This is not a defect. The appliance is working correctly.

Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable).

The appliance door is difficult to close. Rattling/knocking sounds from in side the appliance. The appliance trips the circuit-beak er. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets. • The tableware is not properly arranged in the baskets. Refer to "Loading cutlery and dishes". • Make sure that the spray arms can rotate freely. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. • Internal electrical fault of the appliance. Contact an Authorised Service Centre. Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre.

The washing and drying results are not satisfactory The washing and drying results are not satisfactory Poor washing results. • Refer to "Daily use", "Hints and tips" and "Loading cutlery and dishes". • Use more intensive washing programmes. • Clean spray arm jets and filter. Refer to "Care and Cleaning". 28 Dishwasher User Manual The washing and drying results are not satisfactory Poor drying results. • Tableware has been left for too long inside the closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option Extra dry. • We recommend to always use rinse aid, even in combination with multi-tablets. • For the best drying performance activate DryAssist.

There are streaks, whitish stains, or bluish layers on glasses and dishes. Dry water drops on glasses and dishes. • The release quantity of rinse aid is too large. Adjust the rinse aid se lector to a lower position. • The quantity of detergent is too large. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a higher position. • The quality of the rinse aid can be the cause.

The dishes are wet. • For the best drying performance activate the option Extra dry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • For the best drying performance activate DryAssist. The interior of the appliance is wet. • This is not a defect of the appliance. it is caused by the humidity in the air that condenses on the walls. Unusual foam during washing. • Use the detergent for dishwashers only. • There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre. Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together.

There are residues of detergent in the dispenser at the end of the pro gramme. • The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arm is not blocked or clogged. • Make sure that items in the baskets do not impede the opening of the lid of the detergent dispenser.

Odours inside the appliance. • Refer to "Internal cleaning".

Limescale deposits on the tableware, on the tub and on the inside of the door. • Refer to "The water softener".

Dishwasher User Manual 29 The washing and drying results are not satisfactory

Dull, discoloured or chipped table ware. • Make sure that only dishwasher-safe items are washed in the appli ance. • Load and unload the basket carefully. Refer to "Loading cutlery and dishes". • Place delicate items in the upper basket.

30 Dishwasher User Manual Product information sheet Trade Mark John Lewis Model JLBIDW917 911076051 Rated capacity (standard place settings) 9 Energy efficiency class A+

Energy consumption in kWh per year, based on 280 standard clean ing cycles using cold water fill and the consumption of the low power modes. The actual energy consumption will depend on how the ap pliance is used. 222

Energy consumption of standard cleaning cycle (kWh) 0.777 Power consumption in off mode (W) 0.50 Power consumption in left-on mode (W) 5.0

Water consumption in litres per year, based on 280 standard clean ing cycles. The actual water consumption will depend on how the ap pliance is used Drying efficiency class on a scale from G (least efficient) to A (most efficient) The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and water consumption. It is indicated as "Eco" programme. 2775 A 50° Eco

Programme time of standard cleaning cycle (min) 227 Duration of the left-on mode (min) 5 Sound power level (db(A) re 1pW) 49 Built in appliance Y/N Yes Dishwasher User Manual 31 Additional technical information Dimensions Width / height / depth (mm) 446 / 818 - 898 / 550 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply Cold water or hot water 2) max 60 °C 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to decrease energy con sumption. 32 Dishwasher User Manual

Water connection Water inlet connection This appliance may be fed with either hot (maximum 60 °C) or cold water. Nevertheless we advise you use a cold water supply. A hot water supply is not always efficient with heavily soiled crockery as it shortens the washing programmes a lot. For making the connection itself, the coupling nut fitted to the appliance inlet hose is designed to screw onto a 3/4" gas thread spout or to a purpose made quick coupling tap such as the Press-block. The water pressure must be within the limits given in the ‘Technical data’. Your local Water Authority will advise you on the average mains pressure in your area. The water inlet hose must not be kinked, crushed, or entangled when it is being connected. The appliance features inlet and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut. The locknut must be correctly fitted to avoid water leaks. If the appliance is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. This appliance has been fitted with safety features which will prevent the water used in the appliance from returning back into the drinking water system. This appliance complies with the applicable plumbing regulations. Caution! Do not use inlet and drain hoses which have previously been used on another appliance. Water drain connection The end of the drain hose can be connected in the following ways: • To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the appliance. • To a stand pipe provided with venthole, minimum internal diameter 4 cm. max. 850 mm max. 4000 mm min. 400 mm The drain hose can face either to the right or left of the appliance. Ensure the drain hose is not bent or squashed as this could prevent or slow down the discharge of water. The sink plug must not be in place when the appliance is draining as this could cause the water to syphon back into the appliance. If you use a drain hose extension, the internal diameter must be no smaller than the diameter of the hose provided. Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided. Our appliances are supplied with a security device to protect against the return of dirty water back into the appliance. If the spigot of your sink has a "no return valve" incorporated this can prevent the correct draining of your appliance. We therefore advise you to remove it. When connecting the drain hose to an under sink trap spigot, the entire plastic membrane (A)

Dishwasher User Manual 33 must be removed. Failure to remove all the membrane will result in food particles building up over time eventually blocking the appliance drain hose spigot. A 34 Dishwasher User Manual Electrical connection

Warning! The manufacturer accepts no liability for failure to observe the following safety precautions. • Safety standards require the appliance to be earthed. • Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. • Always plug the mains plug into a correctly installed shockproof socket. • Multi-way plugs, connectors and extension cables must not be used. This could constitute a fire hazard through overheating. • If necessary, have the domestic wiring system socket replaced. In case that the electrical cable has to be replaced, contact your local repair agent. • The plug must be accessible after the appliance has been installed. • Never unplug the appliance by pulling on the cable. Always pull the plug. • The appliance is supplied with a 13 amp plug attached. Use a 13 amp ASTA approved (BS 1362) fuse if it is necessary to change the fuse in the plug supplied. • This appliance complies with the E.C.C. Directives.

Dishwasher User Manual 35 Repairs - after sales service

Your John Lewis appliance comes with a three year guarantee. Your original receipt acts as your guarantee. Please make sure you retain it. The guarantee does not cover you against faults caused by accidental damage or misuse. For further details visit johnlewis.com/customer services. If it is not working correctly refer to the "Troubleshooting" chapter in this user manual. If a fault occurs which you can not resolve through following the advice and information contained within this instruction manual, the next step is to contact John Lewis technical support on: 0330 1230106 They will give you details for your local service engineer. Before calling out an engineer, please ensure you have read the details under the heading “Troubleshooting”. When you contact your local service engineer you will need to give the following details: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of fault 4. The purchase date as found on your receipt 5. The model and serial number of the appliance. So that you always have these numbers at hand, we recommend you to make a note of them here: • Mod....................................... • P.N.C..................................... • S.N......................................... IMPORTANT: If you call out an engineer to a fault listed under the heading ''Troubleshooting'', or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Spare parts Always insist on genuine spare parts. An authorised service engineer should service this product, and only genuine spare parts should be used. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Please contact John Lewis technical support on 0330 1230106 for assistance. Shopping is easy with John Lewis Shops John Lewis, Aberdeen 01224 625 000 John Lewis, Basingstoke 01256 406200 John Lewis, Bluewater 01322 624 123 John Lewis, Brent Cross 020 8202 6535 John Lewis, Birmingham 0345 604 9049 John Lewis, Cambridge 01223 361 292 John Lewis, Cardiff 02920 536 000 John Lewis, Cheadle 0161 491 4914 John Lewis, Chelmsford 0124 545 8400 John Lewis, Cribbs Causeway 0117 959 1100 John Lewis, Edinburgh 0131 556 9121 John Lewis, Exeter 01392 284150 John Lewis, Glasgow 0141 353 6677 John Lewis, High Wycombe 01494 462 666 John Lewis, Kingston 020 8547 3000 John Lewis, Leicester 0116 242 5777 John Lewis, Leeds 0113 3946299 John Lewis, Liverpool 0151 709 7070 John Lewis, Milton Keynes 01908 679 171 John Lewis, Newcastle upon Tyne 0191 232 5000 John Lewis, Norwich 01603 660 021 John Lewis, Nottingham 0115 941 8282 John Lewis, Oxford Street 020 7629 7711 John Lewis, Peterborough 01733 344 644 John Lewis, Reading 0118 957 5955 John Lewis, Sheffield 0114 276 8511 Peter Jones, Sloane Square 020 7730 3434 John Lewis, Solihull 0121 704 1121

36 Dishwasher User Manual

John Lewis, Southampton 02380 216 400 Knight & Lee, Southsea 02392 827 511 John Lewis, Stratford 020 8532 3500 John Lewis, The Trafford Centre 0161 491 4040 John Lewis, Watford 01923 244 266 John Lewis, Welwyn 01707 323 456 John Lewis at home John Lewis, Ashford 01233 811 010 John Lewis, Chester 01244 393 880 John Lewis, Chichester 01243 813 030 John Lewis, Croydon 020 8662 4730 John Lewis, Horsham 01403 214 740 John Lewis, Ipswich 01473 275 850 John Lewis, Newbury 01635 263 980 John Lewis, Poole 01202 756 020 John Lewis, Swindon 01793 733 180 John Lewis, Tamworth 01827 300 580 John Lewis, Tunbridge Wells 01892 506 830 John Lewis, York 01904 557 950

Dishwasher User Manual 37 Environmental concerns

Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

38 Dishwasher User Manual *

Dishwasher User Manual 39 156914424-A-312019 ( Subject to change without notice. )


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply