JEEP RENEGADE 2019 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD JEEP RENEGADE 2019 (01) PDF MANUAL


PDF Content Summary: Renegade 2019 OWNER’S MANUAL

VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non- drinking driver, call a cab, a friend, or use public trans- portation. WARNING! Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. This manual illustrates and describes the operation of features and equipment that are either standard or op- tional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. FCA US LLC reserves the right to make changes in design and specifications, and/or make additions to or improve- ments to its products without imposing any obligation upon itself to install them on products previously manu- factured. Copyright © 2018 FCA US LLC TABLE OF CONTENTS SECTION PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 GRAPHICAL TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 GETTING TO KNOW YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4 GETTING TO KNOW YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 5 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 6 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 7 IN CASE OF EMERGENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8 SERVICING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 9 TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 10 MULTIMEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501 11 CUSTOMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571 12 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577 123456789101112

INTRODUCTION CONTENTS 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . .4 HOW TO USE THIS MANUAL . . . . . . . . . . . . . . .5 ▫ Essential Information. . . . . . . . . . . . . . . . . . . . . .5 ▫ Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ROLLOVER WARNING . . . . . . . . . . . . . . . . . . . . .5 WARNINGS AND CAUTIONS . . . . . . . . . . . . . . . .6 VEHICLE MODIFICATIONS/ALTERATIONS . . . . .6 INTRODUCTION Dear Customer, congratulations on selecting your new vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality. This is a specialized utility vehicle. It can go places and perform tasks that are not intended for conventional pas- senger vehicles. It handles and maneuvers differently from many passenger vehicles both on-road and off-road, so take time to become familiar with your vehicle. If equipped, the two-wheel drive version of this vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle. Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for brak- ing, steering, transmission, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road, or working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a collision. Refer to the “Driving Tips” in “Starting and Operating” for further information. 4 INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and customer oriented documents. In the attached Warranty Booklet you will find a description of the services that FCA offers to its customers, the Warranty Certificate and the details of the terms and conditions for maintaining its validity. Please take the time to read all of these publications carefully before driving your vehicle for the first time. Following the instructions, recommendations, tips, and important warn- ings in this manual will help assure safe and enjoyable operation of your vehicle. This Owner’s Manual describes all versions of this vehicle. Options and equipment dedicated to specific markets or versions are not expressly indicated in the text. Therefore, you should only consider the information which is related to the trim level, engine, and version that you have purchased. Any content introduced throughout the Own- er’s Information, that may or may not be applicable to your vehicle, will be identified with the wording “If Equipped”. All data contained in this publication are intended to help you use your vehicle in the best possible way. FCA aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model described for technical and/or commercial reasons. For further information, contact an authorized dealer. If applicable, refer to the Owner’s Manual Supplement for related information. NOTE: After reviewing the Owner’s Information, it should be stored in the vehicle for convenient referencing, and remain with the vehicle when sold. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techni- cians and genuine MOPAR® parts, and cares about your satisfaction. HOW TO USE THIS MANUAL Essential Information Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustra- tions may differ from your vehicle’s equipment. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Symbols Some vehicle components have colored labels whose sym- bols indicate precautions to be observed when using this component. Refer to “Warning Lights and Messages” in “Getting To Know Your Instrument Panel” for further information on the symbols used in your vehicle. ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not. Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle con- trol. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. INTRODUCTION 5 1 1 1 Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. 6 INTRODUCTION Rollover Warning Label WARNINGS AND CAUTIONS Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.

This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cau- tions. VEHICLE MODIFICATIONS/ALTERATIONS WARNING!

GRAPHICAL TABLE OF CONTENTS CONTENTS 2 FRONT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 REAR VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . .10 INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

FRONT VIEW 8 GRAPHICAL TABLE OF CONTENTS Front View 1 — Engine Compartment 4 — Wheel / Tire 2 — Headlight 5 — Exterior Mirror 3 — Windshield 6 — Door REAR VIEW Rear View 1 — Rear Light 2 — Rear Windshield Wiper 3 — Liftgate Handle GRAPHICAL TABLE OF CONTENTS 9 2 INSTRUMENT PANEL 10 GRAPHICAL TABLE OF CONTENTS Instrument Panel 1 — Headlight Switch 6 — Speed Controls 2 — Instrument Cluster Display Controls 7 — Switch Panel 3 — Multifunction Lever (Behind Steering Wheel) 8 — Uconnect System 4 — Instrument Cluster 9 — Climate Controls 5 — Windshield Wiper Lever (Behind Steering Wheel) 10 — Glove Compartment INTERIOR Interior Features 1 — Door Handles 4 — Selec-Terrain Switch 2 — Door Locks / Window Switches 5 — Gear Selector 3 — Seats 6 — AUX Jack GRAPHICAL TABLE OF CONTENTS 11 2

GETTING TO KNOW YOUR VEHICLE CONTENTS 3 KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ▫ Key Fob With Remote Control . . . . . . . . . . . . . .17 IGNITION SWITCH . . . . . . . . . . . . . . . . . . . . . . .23 ▫ Models With Keyless Enter-N-Go — Passive Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 REMOTE STARTING SYSTEM — IF EQUIPPED . . .24 ▫ How To Use Remote Start. . . . . . . . . . . . . . . . . .25 ▫ Remote Start Cancel Message — If Equipped . . . .26 ▫ To Enter Remote Start Mode . . . . . . . . . . . . . . . .26 ▫ To Exit Remote Start Mode Without Driving The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 ▫ To Exit Remote Start Mode And Drive The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 ▫ Remote Start Comfort Systems — If Equipped . . .27 ▫ Remote Start Windshield Wiper De–Icer And Rear Defrost Activation — If Equipped . . . . . . . . . . .27 ▫ General Information . . . . . . . . . . . . . . . . . . . . .27 SENTRY KEY. . . . . . . . . . . . . . . . . . . . . . . . . . . .28 ▫ Key Programming . . . . . . . . . . . . . . . . . . . . . .28 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . . .28 ▫ General Information . . . . . . . . . . . . . . . . . . . . .29 VEHICLE SECURITY ALARM — IF EQUIPPED . . .29 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .30 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .30 ▫ Disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . . .31 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . . .32 3 3 14 GETTING TO KNOW YOUR VEHICLE ▫ Keyless Enter-N-Go — Passive Entry — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .33 ▫ Automatic Unlock On Exit Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ▫ Dead Lock Device — If Equipped . . . . . . . . . . . .38 ▫ Child Locks . . . . . . . . . . . . . . . . . . . . . . . . . . .39 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 ▫ Manual Front Seats . . . . . . . . . . . . . . . . . . . . . .41 ▫ Manual Rear Seat Adjustment. . . . . . . . . . . . . . .42 ▫ Power Adjustment (Front) — If Equipped . . . . . .44 ▫ Heated Seats — If Equipped. . . . . . . . . . . . . . . .46 ▫ Unfolding The Rear Armrest 40/20/40 . . . . . . . .47 HEAD RESTRAINTS . . . . . . . . . . . . . . . . . . . . . .48 ▫ Front Head Restraints . . . . . . . . . . . . . . . . . . . .48 ▫ Rear Head Restraints . . . . . . . . . . . . . . . . . . . . .49 STEERING WHEEL . . . . . . . . . . . . . . . . . . . . . . .50 ▫ Tilt/Telescoping Steering Column . . . . . . . . . . . .50 ▫ Heated Steering Wheel — If Equipped. . . . . . . . .50 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . . .51 ▫ Auto Dimming Mirror — If Equipped . . . . . . . . .52 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . . .52 ▫ Folding Mirror . . . . . . . . . . . . . . . . . . . . . . . . .54 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . . .54 ▫ Illuminated Vanity Mirrors — If Equipped . . . . .55 EXTERIOR LIGHTS . . . . . . . . . . . . . . . . . . . . . . .55 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 ▫ Daytime Running Lights (DRL) — If Equipped . .56 ▫ High Beams . . . . . . . . . . . . . . . . . . . . . . . . . . .56 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . . .56 ▫ Automatic Headlights — If Equipped . . . . . . . . .57 ▫ Automatic High Beam Headlamp Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 ▫ Parking Lights . . . . . . . . . . . . . . . . . . . . . . . . .58 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . . . .58 ▫ Front Fog Lights — If Equipped . . . . . . . . . . . . .58 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . . .59 INTERIOR LIGHTS . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Courtesy Lights. . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Cargo Area Lights . . . . . . . . . . . . . . . . . . . . . . .64 WIPERS AND WASHERS . . . . . . . . . . . . . . . . . . .64 ▫ Front Wiper Operation . . . . . . . . . . . . . . . . . . . .64 ▫ Rain Sensing Wipers — If Equipped . . . . . . . . . .65 ▫ Rear Wiper Operation . . . . . . . . . . . . . . . . . . . .67 ▫ Windshield Wiper De-Icer — If Equipped . . . . . .68 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . . . .69 ▫ Air Outlet And Diffuser Locations — Passenger Compartment . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Manual Climate Controls Overview . . . . . . . . . .71 ▫ Automatic Climate Control Overview . . . . . . . . .75 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . .83 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Power Window Controls . . . . . . . . . . . . . . . . . .85 ▫ Auto-Down Feature . . . . . . . . . . . . . . . . . . . . .86 ▫ Auto-Up Feature With Auto-Reverse Protection — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ Reset Auto-Up. . . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . .88 POWER MY SKY SUN ROOF — IF EQUIPPED . . .88 ▫ Power My Sky Operation . . . . . . . . . . . . . . . . . .88 ▫ Emergency Open/Close . . . . . . . . . . . . . . . . . . .90 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . .91 POWER GLASS SUNROOF WITH POWER SHADE — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .92 ▫ Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 ▫ Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . . .93 ▫ Power Sun Shade. . . . . . . . . . . . . . . . . . . . . . . .93 ▫ Auto Reverse Feature. . . . . . . . . . . . . . . . . . . . .94 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . .94 3 3

GETTING TO KNOW YOUR VEHICLE 15

16 GETTING TO KNOW YOUR VEHICLE HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 ▫ To Open The Hood . . . . . . . . . . . . . . . . . . . . . .95 ▫ To Close The Hood . . . . . . . . . . . . . . . . . . . . . .96 LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 ▫ Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 ▫ Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 ▫ Cargo Area Features. . . . . . . . . . . . . . . . . . . . . .99 INTERNAL EQUIPMENT . . . . . . . . . . . . . . . . . .105 ▫ Glove Compartment. . . . . . . . . . . . . . . . . . . . .105 ▫ Sun Visors . . . . . . . . . . . . . . . . . . . . . . . . . . .106 ▫ Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . .108 ▫ Power Inverter — If Equipped . . . . . . . . . . . . .109 ▫ Cigar Lighter — If Equipped. . . . . . . . . . . . . . .110 ▫ Ashtray — If Equipped. . . . . . . . . . . . . . . . . . .111 ▫ Front Armrest . . . . . . . . . . . . . . . . . . . . . . . . .112 ▫ Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . .113 ▫ Handle Grip . . . . . . . . . . . . . . . . . . . . . . . . . .114 ROOF LUGGAGE RACK — IF EQUIPPED . . . . . .114 KEYS Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system. The Remote Keyless Entry system consists of a key fob and Keyless Enter-N-Go feature if equipped. NOTE: The key fob may not be found if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal. Key Fob With Remote Control The key fob with Remote Control contains a Remote Keyless Entry feature. The Remote Keyless Entry system allows you to lock or unlock the doors and liftgate or activate the Panic Alarm from distances up to approxi- mately 66 ft (20 m) using a handheld key fob. The key fob does not need to be pointed at the vehicle to activate the system. Key Fobs Keyless Ignition Key Fob GETTING TO KNOW YOUR VEHICLE 17 3 In case the ignition switch does not change with the push of a button, the key fob may have a low or fully depleted battery. A low key fob battery can be verified by referring to the instrument cluster, which will display directions to follow. 18 GETTING TO KNOW YOUR VEHICLE Key Fob Emergency Key Release 1 — Emergency Key Release Button 2 — Emergency Key To Unlock The Doors And Liftgate The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will be activated. 1st Push Of Key Fob Unlock Button This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the unlock button on the key fob. To change the current setting, refer to “Uconnect Settings” in “Multimedia” for further infor- mation.

Push and release the unlock button on the key fob once to unlock the driver’s door or twice within five seconds to unlock all doors and the liftgate. All doors can be programmed to unlock on the first push of the unlock button. Refer to “Uconnect Settings” in “Multi- media” for further information. NOTE: If the vehicle is unlocked by a key fob, and no door is opened within 60 seconds, the vehicle will re-lock and if equipped, the security alarm will arm. NOTE: If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” located in “Doors” in “Getting To Know Your Vehicle” for further information.

To Lock The Doors And Liftgate Push and release the lock button on the key fob to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Refer to “Uconnect Settings” located in “Multimedia” for further programmable infor- mation. If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” located in “Doors” in “Getting To Know Your Vehicle” for further information. Vehicles Equipped With Keyless Enter-N-Go — Passive Entry If one or more doors are open, or the liftgate is open, the doors will lock. The doors will unlock again automatically if the key is left inside the passenger compartment, other- wise the doors will stay locked. Replacing The Battery In The Key With Remote Control The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See dtsc.ca.gov/hazardouswaste/perchlorate for fur- ther information. • Do not touch the battery terminals that are on the back housing or the printed circuit board. GETTING TO KNOW YOUR VEHICLE 19 3 3 3 1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your thumb and pull the emergency key out with your other hand. Emergency Key Removal 1 — Emergency Key Release Button 2 — Emergency Key 20 GETTING TO KNOW YOUR VEHICLE 2. Separate the key fob halves using the tip of the emer- gency key, a #2 flat blade screwdriver, or a coin and gently pry the two halves of the key fob apart. Make sure not to damage the seal during removal. Emergency Key Removal Separating Case With A Coin 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. Key Fob Battery Replacement

4. To assemble the key fob case, snap the two halves together. GETTING TO KNOW YOUR VEHICLE 21 3

Programming Additional Key Fobs Programming the key fob may be performed by an autho- rized dealer. Request For Additional Key Fobs NOTE: Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. WARNING! • Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended. • Always remember to place the ignition in the OFF mode. Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed. 22 GETTING TO KNOW YOUR VEHICLE NOTE: • When having the Sentry Key Immobilizer System ser- viced, bring all vehicle keys with you to an authorized dealer. • Keys must be ordered to the correct key cut to match the vehicle locks. General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IGNITION SWITCH Models With Keyless Enter-N-Go — Passive Entry This feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment. The push button ignition has three operating positions. The three positions are OFF, ON, and RUN. NOTE: If the ignition switch does not change with the push of a button, the key fob may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the key fob against the ENGINE START/STOP button and push to operate the ignition switch. The push button ignition can be placed in the following positions: OFF START/STOP Ignition Button 3

• The engine is stopped. • No electrical devices are available. ON • The vehicle is not running. • Some electrical devices are available GETTING TO KNOW YOUR VEHICLE 23

RUN • Driving position. • All the electrical devices are available. NOTE: The vehicle will not start if the key fob is located inside the cargo area and the liftgate is opened. WARNING! • When leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition in the ON or RUN mode. A child could operate power windows, other controls, or move the vehicle. (Continued) 24 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked vehicle is an invitation for thieves. Al- ways remove key fob from the vehicle and lock all doors when leaving the vehicle unattended. NOTE: For further information, refer to Starting The Engine, in Starting And Operating . REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 328ft (100m). NOTE: • The vehicle must be equipped with an automatic trans- mission to be equipped with Remote Start. • Obstructions between the vehicle and key fob may reduce this range. How To Use Remote Start • Push Remote Start button on the key fob twice within five seconds. Pushing the Remote Start button a third time shuts the engine off. • To drive the vehicle, push unlock button, and place the ignition in the ON/RUN position. • With remote start, the engine will only run for 15 minutes (timeout) unless the ignition key is placed in the ON/RUN position. • The vehicle must be started with the key after two consecutive timeouts. All of the following conditions must be met before the engine will remote start: • Gear Selector in PARK • Doors closed • Hood closed • Liftgate closed • Hazard switch off • Brake switch inactive (brake pedal not pushed) • Battery at an acceptable charge level • PANIC button not pushed • System not disabled from previous remote start event • Vehicle alarm system indicator flashing • Ignition in STOP/OFF position • Fuel level meets minimum requirement WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monox- ide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep key fobs away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death. GETTING TO KNOW YOUR VEHICLE 25 3 3 Remote Start Cancel Message — If Equipped The following messages will display in the instrument cluster if the vehicle fails to remote start or exits remote start prematurely: • Remote Start Cancelled — Door Open • Remote Start Cancelled — Hood Open • Remote Start Cancelled — Fuel Low • Remote Start Cancelled — Liftgate Open • Remote Start Cancelled — Too Cold • Remote Start Cancelled — Time Expired • Remote Start Disabled — Start Vehicle To Reset The message will stay active until the ignition is placed in the ON/RUN position. To Enter Remote Start Mode Push and release the Remote Start button on the key fob twice within five seconds. The vehicle doors will lock, the turn signals will flash twice, and the horn will chirp. Then the engine will start, and the vehicle will remain in the Remote Start mode for a 15-minute cycle. 26 GETTING TO KNOW YOUR VEHICLE NOTE: • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. • The park lamps will turn on and remain on during Remote Start mode. • For security, power window operation is disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive times (two 15-minute cycles) with the key fob. However, the igni- tion must be placed in the ON/RUN position before you can repeat the start sequence for a third cycle. To Exit Remote Start Mode Without Driving The Vehicle Push and release the remote start button one time or allow the engine to run for the entire 15-minute cycle. NOTE: To avoid unintentional shut downs, the system will disable the one time push of the remote start button for two seconds after receiving a valid remote start request. To Exit Remote Start Mode And Drive The Vehicle Before the end of 15-minute cycle, push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter-N-Go — Passive Entry via the door handles, and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15-minute cycle, push and release the START/STOP button. NOTE: For vehicles equipped with the Keyless Enter- N-Go — Passive Entry feature, the message “Remote Start Active — Push Start Button” will display in the instrument cluster display until you push the ignition START button. Remote Start Comfort Systems — If Equipped When Remote Start is activated, the heated steering wheel and driver heated seat features will automatically activate when ambient temperature is less than 40° F (4.4° C). These features will stay on through the duration of Remote Start. Refer to Uconnect Settings in Multimedia for further information. Remote Start Windshield Wiper De–Icer And Rear Defrost Activation — If Equipped When remote start is active and the outside ambient temperature is less than 40°F (4.4°C), the Windshield Wiper De-Icer and the Rear Defrost will be enabled. Exiting remote start will resume previous operation, except if the Windshield Wiper De-Icer is active. The Windshield Wiper De-Icer timer and operation will continue. Refer to Uconnect Settings in Multimedia for further information. General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. GETTING TO KNOW YOUR VEHICLE 27 3 3 SENTRY KEY The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a key fob, keyless push button ignition and a RF receiver to prevent unauthorized vehicle opera- tion. Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid key fob is used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid key fob is used to start the engine. After turning the ignition switch to the ON/RUN position, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key fob to start the engine. Either of these conditions will result in the engine being shut off after two seconds. 28 GETTING TO KNOW YOUR VEHICLE If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics. Key Programming Key fob programming is performed at an authorized dealer. Replacement Keys NOTE: Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! • Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended. • For vehicles equipped with Keyless Enter-N-Go — Ignition, always remember to place the ignition in the OFF position. NOTE: Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed. When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer. General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. VEHICLE SECURITY ALARM — IF EQUIPPED The vehicle security alarm monitors the vehicle doors, hood, liftgate, and the Keyless Enter-N-Go — Ignition for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. If something triggers the alarm, the vehicle security alarm will provide the following audible and visible signals: • The horn will pulse. • The turn signals will flash. • The vehicle security light in the instrument cluster will flash. GETTING TO KNOW YOUR VEHICLE 29 3 3 To Arm The System Follow these steps to arm the vehicle security alarm: 1. Make sure the vehicle’s ignition is placed in the “OFF” mode. 2. Perform one of the following methods to lock the vehicle: • Push the lock button on the interior power door lock switch with the driver and/or passenger door open. • Push the lock button on the exterior Passive Entry Door Handle with a valid key fob available in the same exterior zone (refer to Doors in Getting To Know Your Vehicle for further information). • Push the lock button on the key fob. 3. If any doors are open, close them. To Disarm The System The vehicle security alarm can be disarmed using any of the following methods: • Push the unlock button on the key fob. • Grasp the passive entry door handle to unlock the door, refer to Doors in Getting To Know Your Vehicle for further information. • Cycle the ignition out of the off mode to disarm the system. 30 GETTING TO KNOW YOUR VEHICLE NOTE: • The driver’s door key cylinder and the liftgate button on the key fob cannot arm or disarm the vehicle security alarm. • The vehicle security alarm remains armed during lift- gate entry. If someone enters the vehicle through the liftgate and opens any door, the alarm will sound. • When the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the vehicle security alarm will arm, regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle security alarm. If the vehicle security alarm is armed and the battery becomes disconnected, the vehicle security alarm will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound. If this occurs, disarm the vehicle security alarm. Disabling To completely disable the alarm (e.g. in the case of long inactivity of the car), lock the doors by turning the vehicle key in the exterior door lock cylinder. NOTE: If the batteries in the key fob discharge in the event of a failure to the system or to switch off the alarm, place the ignition in the ON/RUN position. DOORS Manual Door Locks To lock each door, rotate the door lock button on each door trim panel forward. To unlock the doors, pull the inside door handle to the first detent or rotate the door lock button until the lock symbol is no longer visible. If the lock symbol is visible when the door is shut, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door. All doors and the tailgate can be programmed to unlock on the use of one of the front door interior handles. Refer to “Uconnect Settings” in “Multimedia” for further informa- tion on programming locking and unlocking preferences. Locking/Unlocking Doors From Outside With the doors closed, insert the key blade into the driver exterior door lock cylinder and turn to the right to lock the driver’s door. To unlock the driver’s door, insert the key blade into the driver exterior door lock cylinder and turn to the left to unlock the driver’s door. NOTE: The manual lock knob unlocks each individual door separately. Manual Door Lock GETTING TO KNOW YOUR VEHICLE 31 3 3 3 3 32 GETTING TO KNOW YOUR VEHICLE WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle. Always make sure the ignition is in “OFF” mode, remove the key fob from the vehicle and lock the vehicle. Unsuper- vised use of vehicle equipment may cause severe personal injuries or death. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition in the ON or RUN mode. A child could operate power windows, other controls, or move the vehicle. Power Door Locks A power door lock switch is located on each of the front door trim panels. Use this switch to lock or unlock the doors, liftgate and fuel door. NOTE: The key fob may not be able to be detected by the vehicle keyless-go system if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal and prevent the keyless-go system from starting the vehicle. Power Door Lock Switch The doors can also be locked and unlocked with the Keyless Enter-N-Go — Passive Entry system if equipped. Refer to “Keyless Enter-N-Go — Passive Entry” located in “Doors” of “Getting To Know Your Vehicle” for further information. Keyless Enter-N-Go — Passive Entry — If Equipped The Passive Entry system is an enhancement to the vehi- cle’s Remote Keyless Entry system and a feature of Keyless Enter-N-Go. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. NOTE: • Passive Entry can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further infor- mation. • If wearing gloves on your hands, or if it has been raining/snowing on the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time. • If the vehicle is unlocked by the Passive Entry Door Handle, and no door is opened within 60 seconds, the vehicle will re-lock and if equipped, the security alarm will arm. • The key fob may not be able to be detected by the vehicle keyless-go system if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal and prevent the keyless-go system from starting the vehicle. To Unlock From The Driver’s Side With a valid Passive Entry key fob within 5 ft (1.5 m) of the driver’s door handle, grab the front driver door handle to unlock the driver’s door automatically. GETTING TO KNOW YOUR VEHICLE 33 3 3 NOTE: If “Unlock All Doors 1st Press” is programmed, all doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Press” and “Unlock All Doors 1st Press,” refer to “Uconnect Settings” in “Multimedia” for further informa- tion. To Unlock From The Passenger Side With a valid Passive Entry key fob within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automati- cally. 34 GETTING TO KNOW YOUR VEHICLE Grab The Door Handle To Unlock NOTE: All doors will unlock when the front passenger door handle is grabbed regardless of the driver’s door unlock preference setting (“Unlock Driver Door 1st Press” or “Unlock All Doors 1st Press”). Push The Door Handle Button To Lock

To Lock The Vehicle’s Doors And Liftgate With one of the vehicle’s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, push the door handle lock button to lock all four doors. Do NOT grab the door handle when pushing the door handle lock button. This could unlock the door(s).

NOTE: The Passive Entry system will not operate if the key fob battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. Preventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature. DO NOT Grab The Door Handle When Locking FOBIK-Safe only executes in vehicles with Passive Entry. There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: When any of these situations occur, after all open doors are shut, the FOBIK-Safe search will be executed. If it finds a Passive Entry key fob inside the car, and it does not find any Passive Entry key fobs outside the car, then the car will unlock and alert the customer. 1. A lock request is made by a valid Passive Entry key fob while a door is open. 2. A lock request is made by the Passive Entry door handle while a door is open. 3. A lock request is made by the door panel switch while the door is open. GETTING TO KNOW YOUR VEHICLE 35 3 NOTE: The vehicle will only unlock the doors when a valid Passive Entry key fob is detected inside the vehicle, and no valid Passive Entry key fob is detected outside the vehicle. The vehicle will not unlock the doors when any of the following conditions are met: • The doors are manually locked using the door lock knobs. • There is a valid Passive Entry key fob outside the vehicle and within 5 ft (1.5 m) of either Passive Entry door handle. To Unlock/Enter The Liftgate The liftgate Passive Entry unlock feature is built into the electronic liftgate release. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the Electronic Liftgate release to open with one fluid motion. To Lock The Liftgate With a valid Passive Entry key fob within 5ft (1.5 m) of the liftgate, push the Passive Entry lock button located to the right of electronic liftgate release. 36 GETTING TO KNOW YOUR VEHICLE NOTE: • The liftgate Passive Entry lock button will lock the liftgate and the doors. The liftgate unlock feature is built into the Electronic Liftgate release. • If “Unlock All Doors 1st Press” is programmed in the instrument cluster display, if equipped, only the liftgate will unlock when you push the Electronic Release. If Unlock Driver Door 1st Press is programmed in Uconnect, the liftgate will unlock when you push the electronic unlock/lock button on the liftgate. For further information, refer to “Uconnect Settings” in “Multimedia.” Emergency Unlocking Driver Door If the key fob battery is low or dead, the emergency key can be used to unlock the driver side door lock cylinder. To release the emergency key, proceed as follows: 1. Slide the emergency key release button to the side. 2. Remove the emergency key from the key fob with Remote Control housing. Liftgate Release/Passive Entry 1 — Liftgate Handle 2 — Liftgate Passive Entry Location NOTE: The Emergency Key can be inserted into the door lock cylinder from either direction. Emergency Key Release 1 — Emergency Key Release Button 2 — Emergency Key GETTING TO KNOW YOUR VEHICLE 37 3 WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the gear selector. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition in the ON or RUN mode. A child could start the vehicle, operate power win- dows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause them to be severely injured or killed General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 38 GETTING TO KNOW YOUR VEHICLE 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- tion. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Automatic Unlock On Exit Feature — If Equipped If Auto Unlock is enabled, this feature will unlock all the doors when any door is opened if the vehicle is stopped and in PARK. Refer to “Uconnect Settings” in “Multimedia” for further information. Dead Lock Device — If Equipped The Dead Lock Device is a safety device that prevents the use of the internal door handles of the vehicle and the power door lock switch. This device prevents the doors from opening within the passenger compartment. Arming The Dead Lock Device • The device works on all doors and requires two presses of the lock button on the key fob. For vehicles equipped with Passive Entry, the device will also work by pushing the lock button on the driver’s or passenger’s side exterior door handle. • The arming of the device is indicated by three flashes of the direction indicators. • The device does not operate if one or more doors are not properly closed. Disarming The Device • The device will automatically disarm by pushing the unlock button on the key fob. For vehicles equipped with Passive Entry, the device will also disarm by using the driver’s or passenger’s side exterior door handle to unlock and open the door. • Placing the ignition in the ON or RUN position. Child Locks To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child- Protection Door Lock system. To use the system, open each rear door, use a flat blade screwdriver (or ignition key) and rotate the dial to the lock or unlock position. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. Child-Protection Door Lock Location 3 3 3

GETTING TO KNOW YOUR VEHICLE 39

NOTE: • When the child lock system is engaged, the door can only be opened by using the outside door handle even though the inside door lock is in the unlocked position. • After disengaging the Child-Protection Door Lock sys- tem, always test the door from the inside to make certain it is in the desired position. • After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • For emergency exit with the system engaged, rotate the lock/unlock dial to the unlocked position, roll down the window, and open the door with the outside door handle. WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are en- gaged (locked). 40 GETTING TO KNOW YOUR VEHICLE SEATS Seats are a part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Manual Front Seats WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual Front Seats Forward/Rearward Adjustment 3 On models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Manual Seat Adjustment Levers 1 — Forward/Rearward Adjustment Bar 2 — Seat Height Adjustment Lever 3 — Recline Lever GETTING TO KNOW YOUR VEHICLE 41 Height Adjustment The driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Manual Recline Adjustment To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Manual Rear Seat Adjustment WARNING! Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision. Split Rear Seats The split rear seat has the ability to fold flat which increases the storage of the rear cargo area. 42 GETTING TO KNOW YOUR VEHICLE NOTE: • Prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and positioned forward, this will allow the rear seat to fold down easily. • Prior to folding the rear seat, you must secure the rear armrest in the upright position. • You may experience deformation in the seat cushion from the seat belt buckles if the seats are left folded for an extended period of time. This is normal and by simply opening the seats to the open position, over time the seat cushion will return to its normal shape. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Cargo Area Enlargement Folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Fully lower the rear seat head restraints. 2. Move the safety belts to the outboard side of the seat. 3. Pull the seatback release lever to fold both sides of the rear seatbacks completely forward. Partial Enlargement Of The Cargo Area Enlargement of the left side of the cargo area allows you to carry a single passenger on the right side of the rear seat, while the enlargement of the right side allows you to carry two passengers. Proceed as follows: 1. Remove the rear shelf (if equipped). Refer to “Remov- able Rear Shelf” in “Cargo Area Features” for details. 2. Fully lower the rear seat head restraints. 3. Move the safety belts to the outboard side of the seat and rest them on the seat belt guide. 4. Pull the seatback release lever to fold the left or right rear seatback completely forward. Seatback Repositioning NOTE: If interference from the cargo area prevents the seatback from fully locking, you will have difficulty return- ing the seat to its proper position. 1. Move the safety belts to the seat belt guides on the top edge of the seat to ensure the seatbacks properly latch. Rear Seat Release 1 — Seatback Release Lever 2 — Seat Belt Guide GETTING TO KNOW YOUR VEHICLE 43 3 2. Lift the seatbacks, pushing them back until they lock on both the latches. Verify the red notches are no longer visible on the release lever. If the red notches are visible, the seatback is not secure. Power Adjustment (Front) — If Equipped The power seat controls are located on the outboard side of the seat, close to the floor. Use the switch to move the seat up/down, forward/ rearward, tilt (if equipped) and to set the angle of the seatback. 44 GETTING TO KNOW YOUR VEHICLE Rear Seat Latch Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch. Release the switch when the desired position has been reached. Power Seat Switches

1 — Power Seat Switch 2 — Power Recline Switch 3 — Power Lumbar Switch

Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch; the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Tilting The Seat Up Or Down — If Equipped The angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch. The front of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been reached. Reclining The Seatback The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position is reached. WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. (Continued) WARNING! (Continued) • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power Lumbar Adjustment— If Equipped Push the switch forward or rearward to increase or de- crease the lumbar support. Push the switch upward or downward to raise or lower the lumbar support. NOTE: Power seat adjustments are only allowed when the ignition device is turned to ON, and for about 30 minutes after it is turned to OFF. GETTING TO KNOW YOUR VEHICLE 45 3 3 3

Heated Seats — If Equipped The heated seat buttons are located in your vehicle’s touchscreen. You can choose between two heating levels: • Press the heated seat button once to turn the HI setting on. • Press the heated seat button a second time to turn the LO setting on. • Press the heated seat button a third time to turn the heating elements off. If the HI-level setting is selected, the system will automati- cally switch to LO-level after approximately 145 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change. The LO-level setting will turn off automatically after approximately 60 minutes. NOTE: The engine must be running for the heated seats to operate. 46 GETTING TO KNOW YOUR VEHICLE Auto Comfort Systems — If Equipped In vehicles equipped with Auto On Comfort, when turning on the vehicle the driver’s heated seat will automatically turn on when temperatures are below 40° F (4.4° C). Auto Comfort Systems can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further informa- tion. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. Unfolding The Rear Armrest 40/20/40 Tilt the head restraint forward and pull the rear armrest tab to release it from the seat and pull forward. The center part of the rear seat can also be used as rear armrest with cupholders. Rear Seat Center Armrest — If Equipped WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. GETTING TO KNOW YOUR VEHICLE 47

Rear Armrest 3

HEAD RESTRAINTS Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. WARNING! • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash. • Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Front Head Restraints Your vehicle is equipped with front driver and passenger head restraints. 48 GETTING TO KNOW YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push downward on the head restraint. NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see an authorized dealer. Head Restraint Adjustment Button WARNING! • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash. • Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. Rear Head Restraints Your vehicle is equipped with two outboard head restraints and one center head restraint for its rear passengers. The rear head restraints can be raised or lowered. When the center seat is being occupied, the head restraint should be in the raised position. When there are no occupants in the center seat, the head restraint can be lowered for maximum visibility for the driver. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push down- ward on the head restraint. NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see an authorized dealer. Adjustment Button GETTING TO KNOW YOUR VEHICLE 49 3

STEERING WHEEL Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. To unlock the steering column, push the tilt/telescoping lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. 50 GETTING TO KNOW YOUR VEHICLE Tilt/Telescoping Lever To lock the steering column in position, pull the tilt/ telescoping lever upward until fully engaged. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Heated Steering Wheel — If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel switch has been turned on, it will stay on for an average of 80 minutes or more before auto- matically shutting off. This time will vary based on environmental temperatures. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm. The heated steering wheel control button is located in your vehicle’s touchscreen. Auto Comfort Systems — If Equipped In vehicles equipped with Auto On Comfort, when turning on the vehicle the heated steering wheel will automatically turn on when temperatures are below 40° F (4.4° C). Auto Comfort Systems can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further informa- tion. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. MIRRORS Inside Day/Night Mirror The mirror can be adjusted up, down, left, and right. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the lever under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while the lever under the mirror is set in the day position (toward the windshield). NOTE: The mirror will automatically release in the event of heavy contact with a passenger. 3 3 3

Mirror Adjustment GETTING TO KNOW YOUR VEHICLE 51

Auto Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in REVERSE. 52 GETTING TO KNOW YOUR VEHICLE Dimming Mirror Outside Mirrors Power Adjustment Mirrors — If Equipped The power mirror switch is located on the driver’s door panel. To adjust the mirror, rotate the mirror selection switch to the left or to the right and then push the mirror adjustment switch in the four directions indicated by arrows. NOTE:

• To adjust the power mirrors, the ignition must be in the RUN position. • The power mirror switches will remain active for up to three minutes after the ignition is cycled to the OFF position. Opening either front door will cancel this feature. • Once the mirror is adjusted, rotate the control to the neutral position to avoid accidental movements.

Power Mirror Switch 1 — Power Folding Mirror Switch 2 — Mirror Adjustment Switch 3 — Mirror Selector Switch Manual Adjustment Mirrors — If Equipped Manual Adjustment Mirror

To adjust the exterior mirrors, push the corners of the mirrors till desired alignment is obtained. GETTING TO KNOW YOUR VEHICLE 53 3

Folding Mirror The exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, normal and full rear- ward. 54 GETTING TO KNOW YOUR VEHICLE Folding Exterior Mirror Power Folding/Unfolding Mirrors — If Equipped Push the mirror fold/unfold switch briefly to fold or unfold the exterior mirrors. To fold or unfold the exterior mirrors, the ignition must be in the RUN position. NOTE: The fold/unfold mirrors switch will remain active for up to three minutes after the ignition is cycled to the OFF position. Opening either front door will cancel this feature.

Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the Rear Window Defroster.

Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover will turn the light off. Vanity Mirror 1 — Mirror Light 2 — Mirror Cover EXTERIOR LIGHTS Headlights The headlight switch is located on the left side of the instrument panel. The headlight switch controls the opera- tion of the headlights, side marker lights, daytime running lights, fog lights and the dimming of the instrument cluster and interior lighting. Headlight Switch 1 — Rotate Headlight Switch 2 — Ambient Light Dimmer 3 — Instrument Panel Dimmer 4 — Push Fog Light Switch 3 3

GETTING TO KNOW YOUR VEHICLE 55

Turning on the headlights will illuminate the instrument cluster and the controls located on the instrument panel. Daytime Running Lights (DRL) — If Equipped The Daytime Running Lights (DRLs) will turn on when the engine is started and remain on unless the headlights are turned on or the engine is shut off. The DRLs will be disabled during turn signal operation and resume operation when the turn signal operation has ended. High Beams To turn on the high beam headlights, push the turn signal lever forward (toward the front of the vehicle) and an indicator will illuminate in the cluster. To turn off the high beams, pull the turn signal lever rearward (toward the rear of the vehicle). 56 GETTING TO KNOW YOUR VEHICLE NOTE: The headlights must be on for the high beams to activate. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. High Beam And Turn Signal Controls Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the last detent (AUTO position) for automatic headlight operation. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position. To turn the automatic system off, move the headlight switch out of the AUTO position. Refer to “Headlight Delay” in this section for more infor- mation. NOTE: The ignition must be in the RUN or START position before the headlights will come on in the automatic mode. Light Sensor The light sensor is equipped with an infrared LED, located on the windshield. It detects changes in light intensity outside the vehicle, based on the sensitivity of light set by using the menu on the display or on the Uconnect system. The higher the sensitivity, the lesser the amount of external light required for controlling the lighting. Automatic High Beam Headlamp Control — If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automat- ing high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera de- tects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. NOTE: • The multifunction lever must be in the high beam position in order to activate the Automatic High Beams. • The Automatic High Beam Headlamp Control can be turned on or off using the Uconnect System. Refer to “Uconnect Settings” in “Multimedia” for further infor- mation. • Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly. When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels. GETTING TO KNOW YOUR VEHICLE 57 3 3 Parking Lights From the O (off) position, rotate the headlight switch to the first detent (parking position) to turn on the parking lights. The parking light indicator in the instrument cluster will illuminate. Headlight Delay This feature provides the safety of headlight illumination for up to 90 seconds when leaving your vehicle in an unlit area. The time delay of the headlights is programmable between 0, 30, 60 and 90 seconds. Refer to “Uconnect Settings” in “Multimedia” for further information. Headlight Delay Activation To activate the delay feature, place the ignition in the OFF position while the headlights are still on. Then, turn off the headlights within two minutes. The delay interval begins when the headlight switch is turned off from the “Low beam” position. If the headlight switch is in AUTO position and headlights were on before the ignition is OFF, the delay interval begins automatically. 58 GETTING TO KNOW YOUR VEHICLE Headlight Delay Deactivation The feature is disabled by turning on the headlights, the parking lights or by placing the ignition in the RUN position. If you shut off the lights before the ignition is turned on, they will turn off in the normal manner. NOTE: The lights must be turned off within two minutes of placing the ignition in the OFF position to activate this feature. Front Fog Lights — If Equipped The front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and push the fog light button on the headlight switch. To turn off the front fog lights, push the fog light button on the headlight switch a second time or turn off the headlight switch. An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on. Selecting the high beam headlights will turn off the fog lights. Cornering Lights The cornering lights are a feature to improve visibility at night while turning the vehicle. When activated, a light incorporated in the front fog light will illuminate on the side of the vehicle the steering wheel is rotated or the turn signal indicator is on. It can be activated through the Uconnect System. Refer to “Uconnect Settings” in “Multimedia” for further information. Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: When the Daytime Running Lights are on and a turn signal is activated, the Daytime Running Lamp will turn off on the side of the vehicle in which the turn signal is flashing. The Daytime Running Lamp will turn back on when the turn signal is turned off. INTERIOR LIGHTS Courtesy Lights Interior Lights Dimmer Switch Rotate the ambient dimmer control upward or downward to increase or decrease the brightness of the ambient light located in the overhead console, door handle lights, lower instrument panel lights, door map pocket lights, and cubby bin lights. With the parking lights or headlights on, rotate the instru- ment panel dimmer control upward or downward to increase or decrease the brightness of the instrument panel. The instrument panel dimmer has two position at the top of the thumb wheel. The first detent position puts the interior lighting into daytime mode and at the very top detent position will illuminate all the interior lights. At the bottom detent position of the of the instrument panel dimmer, the internal backlights to their lowest dimmable setting and disable the interior lights. GETTING TO KNOW YOUR VEHICLE 59 3 3

Headlight Switch 1 — Ambient Light Control 2 — Instrument Panel Dimmer 60 GETTING TO KNOW YOUR VEHICLE Front Lights The courtesy lights are mounted between the sun visors above the rear view mirror. The light switches are used to turn the lights on or off. Courtesy Lights 1 — Driver’s Courtesy Lights

To operate the courtesy lights, push either the driver or passenger light switch. Courtesy Light Switches 1— Left Switch 2— Right Switch NOTE: • Before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • If a light is left on, it will automatically be turned off after approximately 15 minutes after the ignition is in the OFF position. GETTING TO KNOW YOUR VEHICLE 61 3 Rear Lights Push the button on the rear dome light once to turn the light on, the light will remain on at all times. Push the button a second time to turn the light off, the lights will remain off at all times. 62 GETTING TO KNOW YOUR VEHICLE Rear Dome Light Vehicles With Retractable Roof For vehicles equipped with a retractable roof, there are two interior lights located above the grab handles of the rear doors. Rear Interior Light The lights come on by opening any of the doors. Dome Light Timing The Dome Light will automatically illuminate when the doors are unlocked, the doors are opened or after the doors are closed. Interior Light Locations Timing Entering The Vehicle • The dome light is disabled when the ignition is placed in the RUN or ON position. • The dome lights will turn off automatically when the doors are locked. • The dome lights will automatically turn off after ap- proximately fifteen minutes of inactivity to preserve the battery. The dome lights illuminate in the following ways: • When the doors are unlocked, the dome light will illuminate for approximately 27 seconds. • When one of the doors is opened, the dome light will illuminate for approximately three minutes. • When the doors are closed, the dome light will automati- cally shut off after approximately 27 seconds. The timing stops once the ignition is placed in the RUN or ON position. The dome light will turn off under any of the following conditions: GETTING TO KNOW YOUR VEHICLE 63 3 Timing Exiting The Vehicle The dome light will illuminate under the following condi- tions when the ignition is placed to the OFF position and the key is removed: • The dome light will illuminate for 27 seconds after the ignition is placed in the OFF position. • The opening of one of the doors (approximately three minutes). • After closing a door (approximately 27 seconds). The dome light timing is disabled when the doors are locked. Cargo Area Lights One interior light is located in the cargo area on the driver’s side trim panel. This light automatically turns on/off when the liftgate is opened and closed, regardless of the position of the ignition. WIPERS AND WASHERS The windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. 64 GETTING TO KNOW YOUR VEHICLE CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Front Wiper Operation Rotate the windshield wiper knob to one of the two detent positions for intermittent settings, the third detent for low wiper operation and the fourth for high wiper operation. Windshield Wiper Stalk Windshield Washer Operation To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while the wipers are in the off position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the wind- shield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist Use this feature when weather conditions make occasional usage of the wipers necessary. Push the lever upward to the MIST position and release for a single wiping cycle. NOTE: The Mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and auto- matically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of the two detent positions for intermittent settings, to activate this feature. NOTE: If the end of the multifunction lever rotates from off to the first intermittent setting or from the first intermittent setting to the second intermittent setting, the wipers will perform a round up to clean the windshield. GETTING TO KNOW YOUR VEHICLE 65 3 3 This function can be activated or deactivated by the Uconnect Settings through the radio. Refer to “Uconnect Settings” in the “Multimedia” for further information. The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position one is the least sensitive, and wiper delay position two is the most sensi- tive. Place the wiper switch in the off position when not using the system. 66 GETTING TO KNOW YOUR VEHICLE Rain Sensor Rain Sensing Wipers – Inhibition When the user switches the ignition from OFF to RUN or START with the lever already in the intermittent position, no wipe cycle is performed for safety reasons. This tempo- rary inhibition avoids accidental activations of the wiping (e.g during the hand washing of the windscreen, blocking the blades in ice/snow conditions). The user can activate the Rain Sensing Wipers in three ways: • Moving the level in off position and then in Intermittent positions. NOTE: On vehicles equipped with automatic transmission, the Rain Sensing Wipers will become inactive even if the lever is in one of the intermittent positions if the vehicle is placed in NEUTRAL and the vehicle speed is less than 3 mph (5 km/h). This prevents damage to the windshield wipers during an automatic car wash.

• One MIST command actuation. • The vehicle speed exceeds 3 mph (5 km/h) and the rain sensor detects the presence of rain.

NOTE: • The Rain Sensing feature will not operate when the wiper switch is in the low or high-speed position. • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • Use of Rain-X or products containing wax or silicone may reduce Rain Sensing performance. • The Rain Sensing feature can be turned on and off using the Uconnect System, refer to “Uconnect Settings” in “Multimedia” for further information. Rear Wiper Operation The rear wiper/washer controls are located on the lever on the right side of the steering column. The rear wiper/ washer is operated by rotating a switch, located at the middle of the lever. NOTE: If the front wiper is moving and the vehicle is shifted in REVERSE, the rear wiper will perform one round up to clean the rear window. Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. If the front wiper is set to Automatic Mode (on the wiper stalk as well as “Enabled” through Uconnect settings), placing the rear wiper in an intermittent position will cause the front and rear wipers to sync up. Turning the front wipers off will cause the rear wipers to also stop. To use the washer, push the lever forward and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wiper will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected. If the lever is pushed while the wiper is in the off position, the wiper will operate for several wipe cycles, then turn off. NOTE: As a protective measure, the pump will stop if the switch is held for more than 30 seconds. Once the lever is released, the pump will resume normal operation. GETTING TO KNOW YOUR VEHICLE 67 3 3 Rear Window Defroster The rear window defroster button is located with the Climate Controls on the instrument panel. Push this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster auto- matically turns off after approximately 20 minutes. To manually shut the defroster off, push the button a second time. Auto Comfort Systems — If Equipped In vehicles equipped with Auto On Comfort, when turning on the vehicle the driver’s heated seat will automatically turn on when temperatures are below 40° F (4.4° C). Auto Comfort Systems can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further informa- tion. 68 GETTING TO KNOW YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear win- dow. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heat- ing elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the win- dow. • Keep all objects a safe distance from the window. Windshield Wiper De-Icer — If Equipped Your vehicle may be equipped with a Windshield Wiper De-Icer feature that may be activated under the following conditions: • Activation By Front Defrost — The Windshield Wiper De-Icer will be activated automatically in the case of a cold weather manual start with full front defrost, and the ambient temperature is below 40° F (4.4° C). • Activation By Rear Defrost — The Windshield Wiper De-Icer will be activated automatically when the rear defrost is turned on and the ambient temperature is below 40° F (4.4° C). • Activation By Remote Start Operation — When Remote Start is active and the outside ambient temperature is less than 40° F (4.4° C), the Windshield Wiper De-Icer will be enabled. Upon exiting remote start mode the Windshield Wiper De-Icer will remain on. Remote Start Operation can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further infor- mation. Auto-On Rear Window Defroster/Windshield Wiper De- Icer — If Equipped When turning the vehicle ON, the Rear Window Defroster and Windshield Wiper De-Icer will automatically turn on when the outside ambient temperature is less than 40° F (4.4° C). The Rear Window Defroster and Windshield Wiper De-Icer automatically turn off after approximately 20 minutes. To manually shut the defroster/windshield off, push the button a second time. Auto On can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further information. CLIMATE CONTROLS The Climate Control System allows you to regulate the temperature, air flow, and direction of air circulating throughout the vehicle. The controls are located on the touchscreen (if equipped) and on the instrument panel below the radio. GETTING TO KNOW YOUR VEHICLE 69 3 3 Air Outlet And Diffuser Locations — Passenger Compartment Left Side Air Outlets 1 — Adjustable Air Outlet 2 — Air Vane Adjustment 3 — Air Flow Outlet Adjustment 4 — Fixed Air Outlet 70 GETTING TO KNOW YOUR VEHICLE Center Air Outlets 1 — Fixed Air Outlet 2 — Air Flow Outlet Adjustment 3 — Air Vane Adjustment 4 — Adjustable Air Outlet Right Side Air Outlets 1 — Fixed Air Outlet 2 — Adjustable Air Outlet 3 — Air Vane Adjustment 4 — Air Flow Outlet Adjustment Manual Climate Controls Overview Manual Climate Controls

GETTING TO KNOW YOUR VEHICLE 71 3 Manual Climate Control Descriptions Icon Description 72 GETTING TO KNOW YOUR VEHICLE MAX A/C Button MAX A/C sets the system for maximum cooling performance. Push the button to turn on the MAX A/C setting. In MAX A/C, the blower speed and mode position can be adjusted to de- sired user settings. A/C Button Push the button to engage the Air Conditioning. A light will illuminate when the Air Condition- ing system is engaged. Recirculation Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions, such as smoke, odors, dust, or humidity are present. Recirculation can be used in all modes except for Defrost. Recirculation may be unavailable if conditions exist that could create fog- ging on the inside of the windshield. The A/C can be deselected manually without disturbing the mode control selection. Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. Front Defrost Button The Front Defrost button changes the current airflow setting to Defrost mode. The indicator illu- minates when this feature is on. Air comes from the windshield and side window demist out- lets. When the defrost button is selected, the blower level may increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. When toggling the front defrost mode button, the climate system will return to previous setting. Blower Control Rotate the control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control clockwise from the “0” (OFF) posi- tion. Mode Icon Description Rear Defrost Button Push and release the Rear Defrost Control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window de- froster is on. Temperature Control Push these buttons to regulate the temperature of the air inside the passenger compartment. Pushing the blue arrow indicates cooler temperatures, while pushing the red button indicates warmer temperatures. Mode Button Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Climate Control OFF Button This button turns the Climate Control System off. GETTING TO KNOW YOUR VEHICLE 73 3

Rear Window Defrosting Push and release the rear window defrost button to turn the function on/off. Activation of this function is indicated by the rear defrost indicator light on the instrument panel turning on. If equipped, push the rear defrost button to activate the defrosting of door mirrors and heated rear window. CAUTION! To avoid causing damage to the rear window defroster heating filaments do not affix stickers or other objects to the inside of the rear glass. Air Recirculation Push and release the Air Recirculation button so that the LED is on, to enter recirculation mode. It is recommended to turn the internal air recirculation on while standing in traffic or in tunnels to prevent the introduction of polluted air. Do not use the function for a long period of time, particu- larly if there are many passengers in the vehicle, to prevent the windows from misting up. 74 GETTING TO KNOW YOUR VEHICLE NOTE: Internal air recirculation makes it possible to reach the required heating or cooling conditions quickly depend- ing on the mode selected. Do not use the internal air recirculation function on rainy/cold days as it would considerably increase the possibility of the windows mist- ing. System Maintenance In Winter, the Climate Control system must be turned on at least once a month for approximately ten minutes. Have the system inspected at an authorized dealer before the summer. NOTE: This AC system uses R1234yf Refrigerant.

Automatic Climate Control Overview Uconnect 4 with 7-inch Display Automatic Climate Controls GETTING TO KNOW YOUR VEHICLE 75 3 76 GETTING TO KNOW YOUR VEHICLE Uconnect 4C/4C NAV with 8.4-inch Display Automatic Climate Controls

Automatic Climate Control Descriptions Icon Description MAX A/C Button MAX A/C sets the system for maximum cooling performance. Push the button to turn on the MAX A/C setting. In MAX A/C, the blower speed and mode position can be adjusted to de- sired user settings. NOTE: The MAX A/C button is only on the touchscreen. A/C Button Push the A/C Control Button to change the current setting. The indicator illuminates when the A/C is ON. Pushing the AUTO control button will cause the A/C operation to change to AUTO mode and the A/C indicator will turn off. Recirculation Button Press and release this button on the touchscreen, or push the button on the faceplate, to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions, such as smoke, odors, dust, or high humidity are present. Recirculation can be used in all modes. Recirculation may be unavailable (button on the touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield. The A/C can be deselected manually without disturbing the mode control selection. Continuous use of the Recir- culation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. GETTING TO KNOW YOUR VEHICLE 77 3

78 GETTING TO KNOW YOUR VEHICLE Rear Defrost Button Push the Rear Defrost button to turn on the rear window defroster and the heated outside mir- rors (if equipped). An indicator will illuminate when the rear window defroster is on.

Faceplate Knob Touchscreen Buttons Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen. • Faceplate: The blower speed increases as you turn the blower control knob clockwise from the lowest blower setting. The blower speed decreases as you turn the blower control knob counterclockwise.

Icon Description AUTO Button Pushing this button will automatically control the interior cabin temperature by adjusting air- flow distribution and amount. Performing this function will cause the automatic climate controls to change between manual mode and automatic modes. Refer to “Automatic Operation” within this section for more information. Front Defrost Button The Front Defrost button changes the current airflow setting to Defrost mode. The indicator illu- minates when this feature is on. Air comes from the windshield and side window demist out- lets. When the defrost button is selected, the blower level may increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. When toggling the front defrost mode button, the climate system will return to previous setting.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply