JACKPAK PS600W (01) PDF MANUAL

Read the entire contents of the User Manual before operating or maintaining the JACKPAK PS600W. Failure to follow the instructions and safety precautions can result in serious injury and product damage. Make sure all other operators also read the Manual. Keep the Manual near the product for future reference. By proceeding with operation, you agree that you fully understand the contents of the Manual and assume full responsibility for product use.

This product can expose you to chemicals including styrene and vinyl chloride, which are on the list of over 900 chemicals identified by the State of California to cause cancer, birth defects, or other reproductive harm. Always use this product in accordance with JackPak’s instructions.

JackPak assumes NO liability for damages resulting from:

• Use of the equipment for purposes other than those described in this Manual.

• Modifications to the equipment without prior, written permission from JackPak.

• Injury or death caused by modifying, disabling, overriding, or removing safety features.

• Damages to the equipment from external influences.

• Incorrect operation of the equipment.

The following components are included:

1. Portable Power Station-PS600W

2. AC Adapter

3. 12V Automotive Adapter

4. User Manual (not shown)

The ports and controls on the JACKPAK PS600W are:

1. AC Output Port

2. AC Output Power On/Off Button

3. Main Power On/Off Button

4. 12VDC On/Off Button

5. 12V Car Charger Output

6. 12VDC Output Port (5521)

7. USB-C Input & Output Port

8. USB-A Output Port

9. USB-C & USB-A Output Power On/Off Button

10. LCD Screen

11. LED Light Power On/Off Button

12. LED Light

13. Recharging Input Port (7909)

The LCD screen provides information regarding battery data, power port status, and power station temperature. The key features are:

• Battery Capacity Ring: The central circular ring presents the available battery power. It has 6 separate percentage sectors. When all 6 sectors are illuminated, it indicates a 100% charge. As the battery is used, the sectors will decline, and they will build back during recharging.

• Fault Warning: A triangle with an exclamation mark indicates a fault.

• Power Display: Shows input/output in Watts.

• Port Status Icons: Icons for AC, DC, 12V Car, USB-C, and USB-A will illuminate when the corresponding output is active.

• Temperature Icons: Icons indicate high or low temperature warnings.

• Cooling Fans Icon: Indicates when the internal cooling fans are active.

• Remaining Time Display: Shows the estimated remaining time in minutes or hours.

Power Station charging should be performed in temperatures between +32°F to 113°F (0°C to 45°C). Ensure that cables are connected securely, and the adapter is working properly. Turn the unit off when not in use. Note that once a full charge is achieved, the adapter should be unplugged to extend future battery performance.

The JACKPAK PS600W has five charging methods:

1. Standard AC Adapter: Connect the 7909-input charge port to a wall outlet with the standard 100W AC Adapter. Full charging requires about 7.5 hours.

2. USB-C Charger: Connect the USB-C port to a wall outlet with a USB-C charger (max input 60W). This takes about 10 hours to fully charge.

3. Car Charger: Connect the 7909 input charging port to a vehicle’s 12V power output socket using the standard 7909 transfer cables (max input 78W). This requires approximately 8 hours to fully charge.

4. Solar Panel Charger: Connect the output cable of 100W solar panels to the 7909 input charging ports. This requires at least 8 hours, depending on available sunlight. To optimize, monitor and adjust panels to be perpendicular to sunlight.

5. Adapter + USB-C (Fast Charge): The AC adapter and USB-C charging can operate simultaneously to reduce charging time (max total input 160W). When paired, 3.5 hours are generally required to achieve 80% charging, and approximately 5 hours to fully charge.

Power On

Press the main power button for 2 seconds. The light around the button and the LCD screen will both illuminate. The blue battery ring and current battery charge will also display.

Power Off

Press the main power button again for 2 seconds. The background light and LCD screen will power off at the same time.

110VAC Output

With the main power button ON, gently press the AC Output button (directly above the Power button). The icon “AC” on the LCD screen will light up. The 110VAC outlet may now be used. Press this button again to stop the function; the “AC” icon will disappear.

Car Charger DC Output

When the main power button is ON, gently press the Car Charger Output button (left of the 12V socket). The icons “DC” and “Car” in the LCD screen will light up, indicating the 12VDC function may be used. Press the button again to shut down the function; the icons will disappear.

USB-C & USB-A Output

With the main power button ON, press the USB-C and USB-A Output button (lower right). The USB-C and USB-A icons in the LCD screen will illuminate, indicating the USB functions may be used. Press this button again to shut down the function; the icons will disappear.

To activate the LED light, first confirm that the main power button is ON. Next, press the power button located on the unit’s rear side (on the right side of the LED light’s lens). The operational sequence is as follows:

• Press once for 50% brightness.

• Press again for 100% brightness.

• Press again to activate SOS flashing mode.

• Press again to power off.

When the device is not in use, turn off all functions to reduce power consumption and prolong battery life. Keep your PS600W clean and ensure that the product does not come in contact with water or harsh elements, petroleum products, etc. Store in a dry, clean environment, and keep out of direct sunlight. The storage temperature is between +32°F to 113°F / 0°C-45°C. Fully charge the battery before storing and recharge it every 6 months. If transporting the PS600W, reduce the charge level to approximately 50%.

Technical Specifications

Input

Battery

Physical Specifications

The following table explains the fault codes displayed on the LCD screen and how to troubleshoot them.

• WARNING! Do not allow children to play with or use this device!

• WARNING! If the PS600W becomes excessively hot during charging or discharging, unplug it from the power source or your mobile device immediately. Avoid charging the power station or portable devices in high heat environments.

• WARNING! The PS600W is protected against short circuits, but short circuits may still present risks of excessive heat, fire, or explosion. Keep your power station away from metal objects. Do not insert any metal object into any port or terminal of the PS600W. Always assume the connectors are electrically charged.

• WARNING! Avoid dropping the PS600W. It may damage the internal components and risk short circuiting the device. Make sure that the unit is properly secured when transporting.

• WARNING! Always inspect the power station and do not use if leakage, strange odors, color changes, swelling or any unusual appearances are detected.

• CAUTION! Verify the input voltage required for your device before connecting to the output port! Both over and under voltage may damage your device!

• CAUTION! Run a full charge/discharge cycle at least once every four months to avoid shortening the life span of the internal battery.

• CAUTION! Use the original cable supplied with the PS600W to charge this device for optimal performance! Do not use the unit if the power cord is damaged or broken.

• WARNING! The PS600W is intended as a power supply to recharge electronic devices. This product is not suitable to be used with equipment that relates to personal safety and relies on electricity, such as medical devices and/or warning equipment, equipment for nuclear facilities, the manufacture of aircraft, etc. JackPak therefore assumes no liability for accidents involving personal safety, fires, property, or machine failures caused by using our product with the forementioned devices.

• CAUTION! Check the unit before every use. DO NOT USE if damaged or broken.

• CAUTION! Keep this product away from pets.

• CAUTION! If the PS600W will not be used for an extended period, store in a cool and dry place away from heat sources, moisture, and dust. Avoid leaving the power station in places with either very cold or high temperatures, such as cars parked outdoors and/or in direct sunlight.

• CAUTION! In a storm, unplug the power cord from the power receptacle.

Do not place the JackPak into the trash. It contains a Li-ion battery. Recycle in accordance with your local government guidelines.