J5CREATE WORMHOLE JUC400 (02) PDF DOCUMENT

To use the J5CREATE WORMHOLE JUC400 with a Windows computer, the following are required:

OS: Windows 7 / Vista / XP / 2000

Available USB port: USB 2.0 is recommended

CPU: Intel Pentium II processor or higher

RAM: 512MB RAM or higher

Hard disk: Space requirement of at least 100MB

To use the J5CREATE WORMHOLE JUC400 with a Mac computer, the following are required:

OS: Mac OS X 10.5 or above

Available USB port: USB 2.0 is recommended

CPU: Power PC G4 processor or later

RAM: 512MB RAM or higher

Hard disk: Space requirement of at least 100MB

To use the J5CREATE WORMHOLE JUC400 with an iPad, you will need a USB Connection Kit.

1. Connect one end of the J5CREATE WORMHOLE JUC400 to a standard USB port on one of the two computers. Connect the other end to a USB port on the second computer.

2. When you initially connect the device to the MAC computer, a “Keyboard Setup Assistant” window will pop up. Follow the steps to select the keyboard type. You can also change this setting later by going to “System Preferences” -> “Keyboard” -> “change the keyboard Type”.

3. After the J5CREATE WORMHOLE JUC400 is plugged in, the “Wormhole” CDROM icon will appear on the desktop or in “Macintosh HD”. Double-click the “Wormhole” icon.

4. When the device is connected properly, the wormhole launch page will be shown.

1. Connect one end of the J5CREATE WORMHOLE JUC400 to a standard USB port on one of the two computers. Connect the other end to a USB port on the second computer.

2. The device will automatically start the software installation on both computers.

3. An “AutoPlay” option window may appear. Click on the option “Run WKMLoader.exe”.

4. If the “User Account Control” window appears, click “Yes” to continue.

5. When the device is connected properly, the wormhole launch page will be shown.

If auto-run is not launched, please follow these troubleshooting steps:

A. Ensure both computers are properly connected to the USB cable.

B. Go to My Computer and double-click the j5 Wormhole Switch icon to start the application.

There are three ways to switch keyboard and mouse control between computers:

Use Mouse to Move Off the Edge of Screen: Set “Use mouse move off the edge of screen” with “left side of this pc” in Preferences. Simply move the mouse off the edge of the screen to switch control.

Use Mouse Middle Button: Click the middle button of the mouse to switch the keyboard and mouse from one computer to another.

Hotkey: You can set up a hotkey to activate control switching. The default hotkey is (Alt+S).

Move the mouse cursor to the second computer and open any editing application such as Word, Excel, Power Point, etc. You can then use the keyboard of the first computer to type the text on the file of the second computer.

Note: Please use a Mouse and Keyboard set. The Keyboard Switch function always follows the mouse cursor of the same computer. When using a USB Mouse or Keyboard that is not a set, it will default to its limited screen switching function mode only.

With the clipboard sharing feature, you can copy or paste content bi-directionally between two computers.

1. Open a file and select the content (text/pictures) you want from the first computer, right-click and select “Copy”.

2. Move the cursor to the location on the second computer where you want to place the content, and right-click and select “Paste”.

* When receiving clipboard data from another computer, an icon appears at the bottom right-hand side of the screen.

You can transfer files using one of the following methods:

Drag & Drop: Simply drag and drop the file or folder to the other computer.

Copy & Paste:

1. Right-click on the files you want to copy and select Copy.

2. Move the cursor to the other computer.

3. Move the cursor to the location where you would like to place the file and Right click, then select Paste.

Hotkeys (Shortcut on Keyboard):

1. Click on the files you would like to copy, and press the (Ctrl+C) Keys from a Windows OS computer.

2. Move the cursor to the other computer.

3. Move the cursor to the location where you would like to place the files, and press the (Ctrl+V) Keys to paste the copied files.

Please use the original system hotkey settings on your computer’s operating system (the keyboard always follows the mouse cursor).

From Mac OS to Windows OS: If you are using a Keyboard for MAC OS, you need to press the “Command+C” keys and switch the mouse cursor to the Windows OS computer and press the “Control+V” keys to paste.

From Windows OS to MAC OS: If you are using a Keyboard for Windows OS, you need to press the “CTRL+C” keys and switch the mouse cursor to the MAC OS computer and press “Command+V” keys to paste.

Due to the lack of a USB port on the iPad, you will need a “USB connection kit” to connect the J5CREATE WORMHOLE JUC400. Please follow the steps below:

1. Connect the USB connection kit to the iPad connector.

2. Connect the J5CREATE WORMHOLE JUC400 to a computer and the iPad.

3. Press “Alt+S” on the computer to switch the usage of the Keyboard to the iPad.

4. You can touch the screen on the iPad to the location you want to start typing.

5. You are now ready to type on the iPad using your computer’s keyboard.

To begin setup, click the Wormhole Switch Utility Icon found in both Mac OS & Windows System. The following options are available:

About the Wormhole Switch: Information about the j5 create Wormhole Switch can be found here.

The Position of Other PC: Quickly set up the position of the other computer by using one of the 4 options (Right/Left/Up/Down).

Disable (Enable) the Keyboard and Mouse Control Temporarily & Disable (Enable) Clipboard Share Temporarily: Quickly Disable or Enable sharing options. If one function is disabled, a specific icon will be shown. If both are disabled, another icon will be shown.

Preference Setup:

Show Connection Information: Un-checking this setting means the launch page will not be shown when you start up the device. (*This option is only available in Mac OS Computers).

Resident This Application: When you choose this setting the Wormhole Switch program automatically sets up every time you plug in the device.

Enable Access for System Hotkey: Choose this setting to activate the Hotkey function. (*This option is only available in Mac OS Computers).

Double Click the System Tray Icon to Turn Sharing On/Off Temporarily: Enable/disable the clipboard sharing and Keyboard and Mouse control functions by simply double clicking the icon on the bottom right-hand side of the taskbar. (*This function is only available in Windows OS Computers).

Send Ctrl-Alt-Del to another computer: This option allows for alternative key options for the [Ctrl-Alt-Del] command for the second computer. (*This function is only available when 2 Windows OS Computers are connected).

1. Please make sure your network is available and Do Not unplug the Wormhole during the driver update.

2. Remove the Wormhole cable from the slave computer.

3. Select “Check New Update” or “Online Update” from the utility menu.

4. After you have finished the installation process, re-plug the Wormhole device into both computers.

Select “Quit USB Switch / Exit” from the utility menu. The Wormhole device can be uninstalled in the Confirmation box.