Free English IQUNIX OG80 (01) PDF Document. Free English IQUNIX OG80 (01) PDF User Guide. Free English IQUNIX OG80 (01) PDF User Manual. Free English IQUNIX OG80 (01) PDF Owner Guide. Free English IQUNIX OG80 (01) PDF Owner Manual. Free English IQUNIX OG80 (01) PDF Reference Guide. Free English IQUNIX OG80 (01) PDF Instruction Guide. Free English IQUNIX OG80 (01) PDF Reference Manual. Free English IQUNIX OG80 (01) PDF Instruction Manual. Free English IQUNIX OG80 (01) PDF Operating Instructions.
CLICK HERE TO DOWNLOAD IQUNIX OG80 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What do the different LED indicator statuses mean on the IQUNIX OG80 keyboard?
The LED indicator on the IQUNIX OG80 keyboard is located between the ESC and F1 keys. The color and blinking pattern indicate the keyboard’s status.
| Light and Status | Meaning |
|---|---|
| Red Light Blinking | Low Battery Level |
| Blue Light Blinking / Flashing | Bluetooth Device #1 Re-Connecting / Pairing On |
| Turquoise Light Blinking / Flashing | Bluetooth Device #2 Re-Connecting / Pairing On |
| Yellow Light Blinking / Flashing | Bluetooth Device #3 Re-Connecting / Pairing On |
| Pink Light Blinking / Flashing | 2.4GHz Device Re-Connecting / Pairing On |
| White Light On / Blinking | CapsLock On&Off / Special Keys Combination Enabled |
How are ‘Short Press’ and ‘Long Press’ defined for key combinations on the IQUNIX OG80?
To use special key combinations, you must first hold the FN key.
Short Press: Hold FN first, then the corresponding key, and release both keys.
Long Press: Hold FN first, then the corresponding key. Hold for 5 seconds until the indicator starts blinking.
How do I connect the IQUNIX OG80 keyboard via Bluetooth?
Follow these steps to connect your IQUNIX OG80 keyboard using Bluetooth:
1. Toggle the keyboard Mode Switch to the wireless side.
2. To connect to the first device, Short Press FN + 1 to make the indicator blink in blue. Then, Long Press FN + 1 to make the indicator flash in blue, which indicates the keyboard is in pairing mode.
3. On your computer or device, search for and select the pairing device named [IQUNIX OG80 BT 1]. The indicator will turn off when the keyboard is paired successfully.
To pair a second or third device, repeat the instructions from Step 2, but replace “FN+1” with “FN+2” or “FN+3”. The devices will be shown as [IQUNIX OG80 BT 2] and [IQUNIX OG80 BT 3] respectively.
How do I connect the IQUNIX OG80 keyboard using the 2.4GHz mode?
Follow these steps to connect your IQUNIX OG80 keyboard using the 2.4GHz wireless mode:
1. Toggle the keyboard Mode Switch to the wireless side.
2. Plug the 2.4GHz receiver into your computer. The receiver is located under the magnetic cover of the OBSC (On-Board Storage Compartment).
3. Press FN + 4 to enter 2.4GHz pairing mode. The indicator will turn off when the keyboard is paired successfully.
How do I use the IQUNIX OG80 keyboard in wired mode?
Follow these steps to use your IQUNIX OG80 keyboard in wired mode:
1. Toggle the keyboard Mode Switch to the wired side.
2. Plug the USB cable into your device.
Caution: The rated power for the charger must not exceed 5V-1A. Connection to a higher power output will damage the keyboard.
What are the special key combinations on the IQUNIX OG80 keyboard?
You can use the following key combinations by holding the FN key first:
Long Press FN + TAB: Switch Between Mac/Windows Layout
Short Press FN + Enter: Play/Pause
Short Press FN + ←: Previous
Short Press FN + →: Next
Short Press FN + B: Battery Level Check. The LED Indicator blinks 1, 2, 3,…10 times, which stands for 10%, 20%, 30%,…100% battery level.
Long Press FN + Win: WinLock
Long Press FN + Space: Reset to Default
How do I control the backlighting on my IQUNIX OG80 keyboard?
The following backlight key combinations are available for backlit versions only. Use a short press (press and release) for these functions.
FN + Del: Backlight On/Off
FN + PgUp: Increase Brightness
FN + PgDn: Decrease Brightness
FN + Home: Switch Backlight Effects
FN + End: Switch Backlight Colors
FN + ↑: Increase Backlight Speed
FN + ↓: Decrease Backlight Speed
What are the technical specifications of the IQUNIX OG80 keyboard?
Series: OG80
Number of Keys: 83
Input: 5V-1A
Battery Specifications: 3.7V 4000mAh
What is included in the box with the IQUNIX OG80 keyboard?
The packing list includes the following items:
Keyboard
Dust Cover
USB Cable
2.4GHz Receiver
Keycap & Switch Puller
Bluetooth Dongle
Manual
Warranty Card
CLICK HERE TO DOWNLOAD IQUNIX OG80 (01) PDF DOCUMENT