INTEX ECO20110-1 (01) PDF MANUAL

Read, understand, and follow all instructions carefully before installing and using this product.

To reduce the risk of injury, do not permit children to use this product. Always supervise children and those with disabilities.

Children must stay away from this product and electrical cord(s).

Assembly and disassembly by adults only.

For outdoor use only.

Do not energize or operate the unit if the appliance is damaged or improperly assembled.

Risk of electric shock. Connect only to a grounding type receptacle, this product is provided with a ground-fault circuit interrupter. If replacement of the plug or cord is needed, use only identical replacement parts.

Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.

The unit is provided with a ground-fault circuit interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button, power should be restored. If the GFCI fails to operate in this manner. The GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a qualified service representative before using.

Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other equipment.

To reduce the risk of electric shock, replace damaged cord immediately. Use a qualified electrician to replace the cord.

To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to electric supply; provide a properly located outlet.

Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.

Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI since the ALCI will not protect people.

Position this product away from pool, so as to prevent children from climbing on it and access the pool.

Make sure the electrical parameters indicated on the product correspond to the local mains voltage before you connect the unit.

To reduce the risk of entrapment hazard, never enter the pool if suction strainer component is loose, broken, cracked, damaged or missing. Replace loose, broken, damaged, cracked or missing suction strainer components immediately.

Never play or swim near suction fittings. Your body or hair may be trapped causing permanent injury or drowning.

To prevent equipment damage and risk of injury, always turn pump off before changing the filter control valve position.

Never operate this product above the maximum working pressure stated on the filter tank.

Hazardous Pressure. Improper tank valve cover assembly could cause the valve cover to blow off and cause serious injury, property damage or death.

This product is intended to be used only for the purposes described in the manual!

This product is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.

To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5m) from the pool.

Failure to follow these warnings may result in property damage, electric shock, entanglement or other serious injury or death.

1. In a counter-clockwise motion unscrew plunger valve union from the threaded strainer connector (33). Be careful not to lose the step rubber washer (30). Place the plunger valve on the ground in a safe place.

2. In a counter-clockwise motion unscrew the strainer nut (31) from the threaded connector (33). Leave the flat washer (32) on the connector (33).

3. Install the strainer and plunger valve at the lower position of pool outlet (marked “+”). From the inside of the pool liner insert the connector (33) into one of the pre-cut holes with the washer remaining on the connector to be placed against the inside of the liner wall.

4. Before assembly, lubricate the threads with a petroleum jelly. With the flat side of the strainer nut (31) facing the outside wall of the liner in a clockwise motion screw the strainer nut (31) back onto the threaded connector (33).

5. Finger tighten the strainer nut (31) onto the threaded connector (33).

6. Grasp the plunger valve assembly. Make sure the step washer (30) is in place.

7. In a clockwise motion screw the plunger valve union back onto the threaded connector (33).

8. In a clockwise motion turn the plunger valve handle to close position. Ensure the plunger valve is securely closed. This will prevent water from flowing out during filling of the pool.

1. In a counter-clockwise motion unscrew plunger valve union from the inlet threaded air connector (51). Be careful not to lose the step rubberwasher (30). Place the plunger valve on the ground in a safe place.

2. In a counter-clockwise motion unscrew the strainer nut (31) from the inlet threaded air connector (51). Leave the flat washer (32) on the connector (51).

3. Install the nozzle and plunger valve at the upper position of pool inlet. From the inside of the pool liner insert the nozzle union (34 & 51) into one of the pre-cut holes with the washer remaining on the connector to be placed against the inside of the liner wall.

4. Before assembly, lubricate the threads with a petroleum jelly. Then, with the flat side of the strainer nut (31) facing the outside wall of the liner in a clockwise motion screw the strainer nut (31) back onto the inlet threaded air connector (51).

5. Finger tighten the adjustable pool inlet jet nozzle (34) and the strainer nut (31) onto the inlet threaded air connector (51).

6. Grasp the plunger valve assembly. Make sure the step washer (30) is in place.

7. Screw the air jet valve (50) over the inlet threaded air connector (51). Make sure the air jet valve is securely tighten and facing up. In a clockwise motion screw the plunger valve union back onto the inlet threaded air connector (51).

8. In a clockwise motion turn the plunger valve handle to close position. Ensure the plunger valve is securely closed. This will prevent water from flowing out during filling of the pool.

9. Adjust the direction of the nozzle head pointing away from the pool outlet for a better circulation result.

10. The pool liner is now ready to be filled with water. Consult the above-ground-pool owner’s manual for the filling instructions.

The sand filter removes suspended particles and sanitizes your pool. Pool chemistry is a specialized area and you should consult your local pool service specialist for details.

The Electrocatalytic Oxidation (E.C.O.) is an Advanced Oxidation Process (AOP). When direct current is applied to the electrocatalytic oxidation electrodes, water will be discharged to generate “hydroxyl radicals”. The hydroxyl radical is a powerful oxidant, which oxidizes organic contaminants, and destroys bacteria and algae. Hydroxyl radicals in combination with free available chlorine provide the strongest and safest pool water sanitation.

TOOLS REQUIRED: One (1) Phillips screwdriver

Pump location and mounting:

The system must be installed on a solid level and vibration-free base.

Provide a location protected from the weather, moisture, flooding and freezing temperature.

Provide adequate access, space and lighting for routine maintenance.

Pump motor requires free circulation of air for cooling.

Do not install the pump in a damp or non-ventilated location.

A team of 2 or more people is recommended for setting up this product.

1. Remove the sand filter and its accessories from the packaging carefully and inspect for any visible damage. For missing or damaged parts contact the appropriate Service Center listed in the separate “Authorized service Centers” sheet.

2. In a counter-clockwise motion unscrew the leaf trap cover (14) from the pre-filter housing. Take out the basket (16) and filter housing nut (17).

3. Connect the pre-filter housing to the motor water inlet. Align the connector in the pre-filter housing with the water inlet on the motor.

4. In a clockwise motion screw filter housing nut (17) onto the motor water inlet.

5. Replace the basket (16) and leaf trap cover (14) back to the pre-filter housing.

1. Place the tank support base at the selected location.

2. Place the tank on the tank support base.

3. Connect the motor pre-filtering assembly unit to the tank support base. Ensure the pre-filter housing water inlet hose connection is facing towards the pool. Some countries, especially in the European community, require the product to be secured to the ground or to a base in a permanent upright position. Check your local authorities to determine if there is a regulation in your area regarding above-the-ground swimming pool filter-pumps. If yes, then the product can be mounted to a platform using the two holes located in the base.

The product can be mounted on a cement base or onto a wooden platform to prevent accidental falling over.

The mounting holes are 6.4 mm in diameter and spaced 115 mm apart.

Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.

Use No. 20 silica sand or glass sand with particle size range 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75.

Before loading the tank with sand, ensure the center pipe hub assembly is securely in place at the bottom of the tank, and vertically centered inside the tank.

1. Place the sand shield (7) over the top of the center pipe. Pour the sand into the tank at a slow rate.

2. Fill the tank approximately half way, remove the sand shield (7).

3. Evenly distribute the sand inside the tank, then fill the tank with some water to provide a cushioning effect when the remaining sand is poured in. This prevents the center pipe hub (8) from excessive shock. Place the sand shield (7) back and continue to pour the sand into the tank.

4. Sand shall be filled between the “MAX” and “MIN” marked gauge on the center pipe. Evenly spread and level out the sand by hand.

5. Remove the sand shield (7).

6. Wash away all sand around the top edge of the tank.

Improper tank valve and clamp assembly could cause the valve and clamp to blow off and cause serious injury, property damage or death.

1. Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding underneath the 6-way valve fits securely into the center pipe hub (8) top opening.

There are three hose connection ports on the 6-way valve, ensure the outlet connection (from filter to the pool) on the valve is facing towards the pool, and the inlet connection (from motor to valve) is aligned with the motor outlet.

2. Remove the clamp bolt, and install the clamp around the tank and 6-way valve flanges, then replace the clamp bolt and use a phillips screwdriver (not included) to tighten it.

3. Connect the sand filter interconnecting hose (13) between the 6-way valve inlet and motor outlet, and insert the electrolytic cell (22) into the 6-way valve outlet. Hand tighten them securely.

4. Screw and tighten the flow sensor (21) to the electrolytic cell (22), then plug in the electrolytic cell line cord and tighten the nut.

Position this product away from the pool, so as to prevent children from climbing on it and accessing the pool.

The 6-way valve has three hose connection ports.

1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose to the lower plunger valve with the strainer. Ensure the hose nuts are securely tighten.

2. Connect the second hose (12) between the electrolytic cell outlet and the upper plunger valve with the inlet-nozzle. Ensure the hose nuts are securely tighten.

3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be directed to a proper draining receptacle using a hose or pipe (not provided). Remove the drain cap before attaching the drain/waste hose or pipe.

4. The sand filter pump is now ready to filter the pool.

For NON-INTEX pool:

1. Connect the hose (12) to the pool inlet/outlet connection with a large hose clamp. Tighten securely.

For INTEX pool with 1-1/4″ (32mm) connections/hoses:

Make sure the air jet valve (50) is securely tighten onto the pool inlet air adaptor (51) and facing up.

Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a portable residual current device (PRCD).

To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to electric supply; provide a properly located outlet.

Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.

Never operate this product above the maximum working pressure stated on the filter tank.

Always switch off pump before changing the 6-way valve position.

Operating this product without water flowing through the system can cause a build up of hazardous pressure which can result in an explosive situation, serious injury, property damage or death.

Never test this pump with compressed air. Never operate the system with water temperature above 35° C (95° F).

Before operating, be sure that:

All the hoses have been connected and tightened securely, and correct amount of filter sand have been loaded.

The entire system is connected to a grounding type receptacle protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD).

The filter control valve has a closed position. The pump should never be on when the valve is in the closed position. If the pump is operated with the valve closed, an explosive situation could exist.

1. Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves to allow water to flow into the sand filter pump.

2. Ensure the drain/waste outlet on the 6-way valve is not covered and directed to a proper draining receptacle.

3. Ensure the pump is off, depress the 6-way valve and turn it to the “BACKWASH” position. To prevent damage to the 6-way valve, always depress the valve handle before turning. Always switch off pump before changing the 6-way valve position.

4. Switch on the pump. Water is circulating backward through the sand media and to waste/drain outlet. Backwash until a clear flow of water is observed in the waste/drain outlet or through the drain sediment window. The initial backwash of the filter is recommended to remove any impurities or fine sand particles in the sand media.

5. Switch off the pump, change the 6-way valve to “RINSE” position.

6. Switch on the pump and run the pump for about one minute to level out the sand bed after backwashing the sand media.

7. Switch off the pump, change the 6-way valve to “FILTER” position.

8. Switch on the pump. The system is now operating in the normal filtering mode. Run the pump until the desired pool water clearance is obtained and no more than 12 hours per day.

9. Record the initial pressure gauge reading when the filter media is clean. During initial setup of the system, it may be necessary to backwash frequently due to unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and impurities from the pool water, the accumulated dirt in the sand media will cause the pressure to rise and the flow to diminish. If there is no vacuuming device attached to the system and the pressure gauge reading is in the yellow zone it is time to backwash the sand media. Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also cause the flow to diminish and the pressure to rise. Remove any vacuuming device from the system and check if the pressure gauge reading has dropped from the yellow zone to the green zone.

1. Plug the power cord into the electrical outlet and test the GFCI/RCD (circuit breaker). Switch on the unit. With the Filter Pump turned “ON” and operating. Flashing code“00” appears on the electronic control station’s LED, indicating that the unit is ready to be programmed.

2. With code “00” flashing, press the button to set the desired operating hours. See the “Operating Time Table” for the required operating hours related to each pool size. Pressing the button will increase the time from 01 to 12 hours maximum. If you have selected too many hours keep pressing the button to repeat the cycle. The built-in timer will now activate your Saltwater System, at the same time each day, for the number of hours you have set. The Saltwater System will not operate if the filter pump is not operating.

With the desired hour value showing, press the button until you hear a “beep”. The green “WORKING” indicator on the control panel will light up within a few seconds to indicate that the saltwater system has started sanitizer production. Locking the control buttons into this setting prevents unauthorized changing of the operating cycle.

If you forget to lock the keypad controls, the system will automatically lock it and start working 1 minute later.

The operating hours can be re-adjusted if necessary. Press the button until you hear a “beep” to unlock the keypad and the current programmed time will flash. Repeat steps for setting operating hours and locking keypad controls.

First time installation, press and hold “BOOST” button for 5 seconds until the indicator lights up and the LED display “80”. This indicates that the saltwater system has started E.C.O. and more chlorine sanitizer production. You can press and hold the “BOOST” button for another 5 seconds until the indicator is off, which will cancel the Boost cycle.

The boost operating hours is 8 times the amount of time programmed into the system, i.e. if your saltwater system operating time is 2 hours, the boost procedure will run 8 x 2 = 16 hours. After boost procedure has been completed, the system will automatically switch to the normal working mode.

After a heavy rain or if the pool is dirty, press the “BOOST” button to shock the pool again.

When the cycle ends, the green “SLEEP” indicator on the control panel lights up and the LED display flashes “93”. The system is now in Stand-By mode. After a while, it shuts down and sets itself in a Power Saving mode.

The system will automatically turn itself back on in 24 hours, starting its daily cycle of chlorine production.

The “SLEEP” indicator stays on, while the system is in the Power Saving mode. The LED display however, goes blank after 5 minutes. Press any button ( or ) to view the last LED code.

To run the pump alone without the Saltwater System function, press and hold both (pump) and (unlock/lock timer) buttons for 5 seconds until you hear a “beep” and the LED display shows “FP”. The pump is now operating alone. To stop the pump, manually turn the switch OFF. The pump cannot be operated alone under an automatic timer mode.

a) If the LED display shows “FP”, press the button and the operating hours set previously will begin flashing, press the button again or simply wait 1 minute, and the LED will stay illuminated. The Saltwater System cycle repeats again.

b) If the unit is OFF, turn the switch ON, the LED display shows “FP”, press the button and the operating hours set previously will begin flashing, press the button again or simply wait 1 minute, and the LED will stay illuminated. The Saltwater System cycle repeats again.

Use only Sodium Chloride Salts (NaCl) salt that is at least 99.8% pure. It is also acceptable to use water conditioning salt pellets (the compressed forms of evaporated salt). However, it will take a longer time for them to dissolve. Do not use iodized or yellow (yellow prussiate of soda) colored salt. Salt is added to the pool water and the electrolytic cell uses the salt to create the sanitizer. So, the purer the salt the better the performance of the electrolytic cell.

The ideal salt level in the pool water is between 2500-3500 ppm (parts per million). The optimal level is 3000 ppm.

A too low salt level will reduce the efficiency of the saltwater system and result in low sanitizer production. A high salt level may generate a salty taste to the pool water (this may occur at a salt level above 3500-4000 ppm). Too high of a salt level may damage the power supply and cause corrosion to pool metal fixtures and accessories. The Salt Table page of this manual, shows the correct dosage of salt needed. The salt in the pool is constantly recycled. Salt loss occurs only when pool water is physically removed from the pool. Salt is not lost due to evaporation.

1. Switch on the unit, then press and hold both the pump and unlock/lock timer button for 5 seconds, the LED flashes “FP”. The unit is now in a Filter pump working mode and switch the filter pump on to start the water circulation.

2. Keep the Saltwater System turned off.

3. Determine the amount of salt to be added (see “Salt Table”).

4. Evenly spread the proper amount of salt around the inside perimeter of the pool.

5. Avoid clogging the filter by not adding salt through the skimmer.

6. Brush the pool bottom to speed up the dissolving process. Do not allow salt to pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to thoroughly dissolve the salt.

7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System, press the button until you hear a “beep”, code “00” flashing and set the saltwater pool system to desired operating time (see “Operating Time Table”).

If too much salt has been added, the unit will beep and display “Code 92”. You will need to lower the salt concentration. The only way to do so, is to partially drain the pool and refill it with fresh water. Drain and refill approximately 20% of the pool’s water until the “Code 92” disappears.

This table shows the dosage of salt needed to achieve and maintain the optimal 3000 ppm salt level.

Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet rays. To maintain the pool water clear and clean, and to maximize the performance of the device, add cyanuric acid to the pool. We recommend that the cyanuric acid level be maintained at approximately 1% of the salt, i.e. 100 Lbs (45 Kgs) salt x 1% = 1 Lbs (0.45 Kgs) cyanuric acid. If the pool water is dirty, filthy or grimy, DO NOT add chlorine stabilizer (cyanuric acid) as this will slowdown the sanitation time of the device. Under this condition you must BOOST your pool water, refer to BOOST cycle steps. Once the pool water has been restored to clear and clean conditions you may add cyanuric acid.

1. Make sure the filter pump is switched off, then disconnect the power cord from the electrical outlet.

2. Turn both plunger valve handles fully clockwise until they stop. This closes the valve, prevents the water from flowing out of the pool.

3. Release the pressure first by opening the sediment release valve (19) located on the lower side of the pre-filter housing.

4. In a counter-clockwise motion unscrew the leaf trap cover (14), then remove the basket (16) and leaf trap o-ring (15) from the pre-filter housing.

5. Empty and flush the basket using a garden hose, may use a plastic brush to remove deposits from the basket. Do not use metal brush.

6. Clean and rinse the inside of the pre-filter housing and the leaf trap O-ring with a garden hose.

7. Reinstall the leaf trap O-ring, basket and leaf trap cover to the pre-filter housing.

8. Close the sediment release valve (19) back.

1. In a counter-clockwise motion unscrew the collar of the flow sensor (21) and remove it from the electrolytic cell conduit (22).

2. If deposits and debris are seen on the surface of the flow sensor, then use a garden hose to wash it off.

3. If flushing with water does not remove the deposits, use a plastic brush to clean the surface and the hinge if necessary. Do not use a metal brush.

4. After the flow sensor has been inspected and cleaned, align the locator notch on the flow sensor to the connection ridge in the conduit. Now turn the collar in a clockwise motion, tightening the sensor back into its position. Do not overtighten.

The titanium electrode and E.C.O. electrodes have a self cleaning function incorporated into the electronic control’s programming. In most cases this self cleaning action will keep the electrodes working at optimum efficiency. If the pool water is hard (high mineral content) the electrodes may require periodic manual cleaning. To maintain maximum performance, we recommend that you open and visually inspect the titanium and E.C.O. electrodes (4 & 5) monthly.

1. Switch off the unit, unplug the power cord from the electrical socket.

2. Disconnect the hose (12) from the electrolytic cell (22) outlet and cover the outlet with the drain outlet cover (3) from the 6-way valve.

3. Remove the electrolytic cell from the 6-way valve outlet by unscrewing the electrolytic cell (22) collar.

4. Pour kitchen grade vinegar into the cell to immerse the titanium plates. Soak for about 1 hour and then flush with a high-pressure garden hose.

5. Reverse steps 2 to 4 to reconnect the electrolytic cell.

1. Switch off the unit, unplug the power cord from the electrical socket.

2. In a counter-clockwise motion, unscrew the electrical plug collar from the E.C.O. electrode cell, and remove the electrical plug from electrode cell.

3. Unscrew the E.C.O. electrode cell collar, then remove the electrode cell and place it on a bucket.

4. Pour kitchen grade vinegar into the bucket until the E.C.O. electrode cell is immersed. Soak for 1 hour and then flush with a high-pressure garden hose.

5. Reverse steps 2 to 4 to reconnect the E.C.O. electrode cell.

The Test Strips can test the “Free Chlorine”, “pH”, “Calcium Hardness” and “Total Alkalinity” levels at the same time. We recommend that you test the water chemistry weekly, and maintain the chlorine concentration at 0.5-3 ppm.

Directions and Use:

1. Dip the entire strip into the water and remove immediately.

2. Hold the strip level for 15 seconds. Do not shake excess water from the strip.

3. Now compare the strip pad to the color chart on the packaging label. If necessary, adjust the chemical level in the pool water. It is very important, to use the proper technique when testing the water’s chemical level. Read and follow the written strip instructions carefully.

All pools require care to keep the water clear and hygienically clean. With proper chemical control, your filter will help attain this objective. Consult your pool supply dealer for instructions regarding the proper use of chlorine, algaecide and other chemical agents required for sparkling clear water.

Keep pool chemicals away from children.

Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could occur.

Daily pH checking and chemical treatment of the water is very important and cannot be overemphasized. Maintenance of proper pH levels are required when filling the pool as well as during the season. Consult your local swimming pool supply store for instructions.

The season’s first filling of the pool may have brackish water requiring extra water additives and extra filtering time. Do not allow swimming in pool until the pH level is balanced. Consult your local swimming pool supply store for instructions.

Chlorinated water may damage lawns, gardens or shrubbery as children play in the pool and splash water outside the pool. Lawn areas underneath the pool liner will be destroyed.

Note that some types of grass may grow through the liner.

Filter run time depends on pool size, weather and usage level. Experiment with various run times so as to produce clean clear water.

Consult with local swimming pool dealer for water treatment.

Free Chlorine: Is the chlorine residual present in pool water.

Combined Chlorine: Is formed by the reaction of free chlorine with ammonia wastes. Result if too high – Sharp chlorinous odor, eye irritation.

pH: A value that indicates how acidic or basic a solution is. Result if too low – Corroded metals, eye & skin irritation, destruction of total alkalinity. Result if too high – Scale formation, cloudy water, shorter filter runs, eye & skin irritation, poor chlorine efficiency.

Total Alkalinity: Indicates the degree of the water’s resistance to change in pH. It determines the speed and ease of pH change, so always adjust total alkalinity before adjusting the pH level. Result if too low – Corroded metals, eye & skin irritation. Low alkalinity will cause the pH to be unstable. Any chemical added to the water will have an affect on pH. Result if too high – Scale formation, cloudy water, eye & skin irritation, poor chlorine efficiency.

Calcium Hardness: Refers to the amount of calcium and magnesium dissolved in the water. Result if too high – Eye & skin irritation, difficulty balancing water and poor chlorine efficiency. Scale will form and will cause the water to become cloudy.

Stabilizer (Cyanuric Acid): Stabilizers extend the life of chlorine in swimming pools.

Do not add pool chemicals directly to the skimmer. This may damage the cell.

Maintaining a salt and sanitizer level above the recommended range can contribute to the corrosion of the pool equipment.

Check the expiry date of the test kit as the test results may be inaccurate if the kit is used after that date.

If, due to heavy pool usage, it is required to increase the sanitizer level, then use a chemical based on trichlor, TCCA or dichloro.

Allowing the water to freeze will damage the sand filter and void the warranty. If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is non-toxic and will not damage plastic system components; other anti-freezes are highly toxic and may damage plastic components in the system.

1. Before emptying your pool for long term storage, or relocation, be sure the water is directed towards an acceptable drain water receptacle away from the house. Check local regulations for specific directions regarding disposal of swimming pool water.

2. Switch off the unit, and disconnect power cord from electrical outlet.

3. When the pool is empty, disconnect all hoses from pump and plunger valves and remove the strainers/plunger valves from the pool wall.

4. In a counter clockwise motion unscrew the drain valve cap (9) from the drain valve to thoroughly drain the tank. The drain valve is located at the bottom of the filter tank.

5. Disassemble the pump motor from the tank base.

6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.

7. Coat the following o-rings and washers with petroleum jelly for long term storage: L-shape o-ring (27), o-ring A (18), Pump hose O-rings (29), Strainer valve assembly step washers (30), Flat strainer rubber washers (32).

8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve top “N” position. This allows the water to drain from the valve. Leave the 6-way valve in this inactive position.

9. It is best to place all dry pieces and pump motor in the original packaging for storage. To avoid condensation or corrosion problem, do not cover or wrap pump motor with plastic bags.

10. Store the pump motor and accessories in a dry place. The storage’s temperature should be controlled, between 0 degrees Celsius (32 degrees Fahrenheit) and 40 degrees Celsius (104 degrees Fahrenheit).

Water recreation is both fun and therapeutic. However, it involves inherent risks of injury and death. To reduce your risk of injury, read and follow all product, package and package insert warnings and instructions. Remember, however, that product warnings, instructions and safety guidelines cover some common risks of water recreation, but do not cover all risks and or dangers.

For additional safeguards, also familiarize yourself with the following general guidelines as well as guidelines provided by nationally recognized Safety Organizations:

Demand constant supervision. A competent adult should be appointed as a “lifeguard” or water watcher, especially when children are in and around the pool.

Learn to swim.

Take the time to learn CPR and first aid.

Instruct anyone who is supervising pool users about potential pool hazards and about the use of protective devices such as locked doors, barriers, etc.

Instruct all pool users, including children what to do in case of an emergency.

Always use common sense and good judgement when enjoying any water activity.

Supervise, supervise, supervise.