IMAGETECH M6 (01) PDF Document

The following goods are included with your IMAGETECH M6 delivery:

• iMageTech M6

• USB cable

• USB adapter

• Audio Cable Set

The buttons, ports, and indicators on the IMAGETECH M6 are as follows:

1. Power switch/audio source switch key/power indicator

2. Audio source indicator

3. Pairing key/connection status indicator (white) (S0, S1, S2, S3, S4, S5)

4. Audio input port (Line-In)

5. Audio output port (Line-Out)

6. USB Port

Follow these steps to start using your IMAGETECH M6:

Step1: Connect the IMAGETECH M6 Wireless Speakerphone System to the USB power supply (No.6); press and hold the “Power on key (No.1)” for three seconds to initiate your product.

Step2: Press and hold the “pairing key (No.3)” for 3 seconds until the “Connection status indicator (white)” flashes quickly to start pairing with iMage A6 (A7); pair the S0, S1, S2, S3, S4, and S5 of iMage A6 (A7) in sequence; the latter is paired successfully when the connection status indicator lighted on. (Set your iMage A6 (A7) to Link mode in advance.)

Step3: Select the audio source (Bluetooth, USB, video) according to the audio device you desire to connect; select Bluetooth mode for mobile devices including smartphone or tablet; select USB mode for desktop or notebook computer; select LINK (Line-in/Line-Out) mode along with a dedicated audio cable for video host or audio device.

The audio source indicator lights on the IMAGETECH M6 have the following meanings:

• Blue light: Bluetooth mode

• Red light: USB mode

• Indicator dimmed: LINK (Line-in/Line-out) mode

• Purple light: Expansion mode

* Note: These are data tested in lab environment; actual ones may vary with operation conditions.

You may connect the IMAGETECH M6 Wireless Speakerphone System to desired backend audio devices in Bluetooth, USB, video and expansion mode with the “Audio source switch key (No.1)”.

• Bluetooth mode (blue light): Your IMAGETECH M6 enters the pairing mode once switched to Bluetooth mode; smartphone or tablet with Bluetooth mode enabled then can find and pair with your iMage M6 automatically.

• USB mode: Connect your IMAGETECH M6 to PCs with USB cable and start using it.

• LINK mode: See chapter “Video host connection guidelines” and “Wiring guidelines” for reference.

• Expansion mode: Designed to use at site of greater space by serial connecting more iMage A6(A7) with IMAGETECH M6.

To determine connection status of your IMAGETECH M6 based on the “Connection status indicator (white)”:

• Pairing in progress: flashing quickly

• Paired successfully: lighting up

• No device connected: flashes once every 5 seconds

• This product works only with slave device iMage A6 (A7).

• To use this product successfully, the channel “S0” is required to connect to a slave device.

• Connecting audio device in video mode requires engineer to wire and set up the system in advance; in case you encountered any problem when doing so, call engineers for service.

• You may connect with an iMage A6 (A7) up to 20 meters apart if it is not blocked by a wall or other larger obstacles.

• Your IMAGETECH M6 can be paired with up to 6 iMage A6 (A7) devices. When pairing for the first time, it is recommended to pair the next iMage A6 (A7) only after the last has been paired successfully.

• It takes 30-45 seconds to pair iMage M6 with iMage A6 (A7) for the first time; after that it takes up to 10 seconds once powered on to pair each other successfully.

• Wall/ceiling mount: Equipment mass ≤ 1kg mounted ≤ 2m

1. Wires required: You will need two 3.5mm(3 poles) to 3.5mm(3 poles) audio cables.

2. Wiring guidelines:

• Connect one cable from the “Audio In” port on the IMAGETECH M6 to the “Audio Out” port on the Polycom Group 500.

• Connect the second cable from the “Audio Out” port on the IMAGETECH M6 to the “Audio In” port on the Polycom Group 500.

Please have professional engineers do the wiring for you as invalid connection may result in malfunction of the system.

1. Wires required: You will need two 3.5mm(3 poles) to 3.5mm(3 poles) audio cables.

2. Wiring guidelines:

• Connect one cable from the “Audio In” port on the IMAGETECH M6 to the “Audio In” port on the AVAYA XT Series device.

• Connect the second cable from the “Audio Out” port on the IMAGETECH M6 to the “Audio Out” port on the AVAYA XT Series device.

Please have professional engineers do the wiring for you as invalid connection may result in malfunction of the system. Note: The audio values and standards of different video hosts’ I/O ports may vary or require special signal converter for interface. Please refer to specification of devices to be connected for more information.

If the IMAGETECH M6 causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The IMAGETECH M6 device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.