HYUNDAI H-HV18-10-UI3321 (01) PDF MANUAL

Before starting up for the first time, check that the specifications on the product comply with the power supply specifications.

The device should be located away from flammable and easily deformable objects.

When the device is not in use for a long time, store it in a cool, dry place in the original cardboard box. If the device was at a temperature below 0°C for some time, it must be kept at room temperature for at least 2 hours before turning it on.

DO NOT COVER THE DEVICE while it is operating. Do not dry clothes or any other fabrics and materials on it. This can lead to overheating, failure, or significant damage to you and / or your property.

Always unplug the device before assembling, disassembling and cleaning, or if you are not using it.

If it is impossible to insert euro plug into an outlet or it is hard to do so, flip the plug vertically 180 degrees and try again. If even after that you cannot easily insert the plug into the outlet, call an electrician to replace the outlet. Never use the appliance if the plug is not fully inserted into the outlet.

Never connect the appliance to the power supply if its surface is wet. Never use the device in a situation where it may come into contact with water.

If the power cord or plug is damaged, to avoid danger, it must be replaced by the manufacturer, authorized service center, or similar qualified personnel.

It is forbidden to install and use the device in bathrooms, showers or pools, precisely in those places where there is a possibility of direct hit of jets and drops of water on its surface during the time when the device is turned on.

Do not lay the appliance’s power cord under carpets or press it with furniture. Route the power cord so that it was impossible stumble over it. When disconnecting the appliance from the mains, do not pull on the power cord, grasp the plug. Do not twist and do not wind it on anything.

To prevent a possible fire, do not block the air inlets and outlets. Do not hang or dry things on the convector! Use the convector only on a flat, dry surface.

In order to avoid overheating and the risk of fire, as well as damage to the internal electrical network, do not change the length of the power cord or connect the device through electrical extension cords. However, if necessary, an extension cord can be used if its parameters correspond to the power of the device and if it is not used by other consumers of electricity.

Install and operate the appliance in a strictly upright position. It is forbidden to operate the device in horizontal or inclined positions.

The device must be installed so that the control panel cannot be accessible to a person who is in the bathroom (in contact with water) or taking a shower.

1. Open the packaging and carefully remove the appliance and wall-mounting kit from it.

2. Remove any foam seals on the edges of the device and release it from plastic bag.

3. Choose the location for the installation of the device in compliance with the minimal distances from other objects and floor according to Fig. 2.

4. Drill holes in the wall of the required diameter and depth.

5. According to the marks, insert the dowels and attach the mounting brackets with the screws (included in the delivery set)

6. Fix the wall feet on the back panel of the device with the screws.

7. Mount the convector on the wall, aligning the grooves with the brackets.

8. Fix the convector by installing the wall brackets holders in the upper part of the grooves and securing it with the screws (included in the delivery set)

9. Wall installation of the device is carried out by the following pictures

Unplug the device before connecting the wheels

1. Remove two support feet and wheels from the packaging of the convector.

2. Turn the device upside down.

3. Attach the support feet to the bottom of the device connecting them with the holes on the device. Attach the feet carefully.

4. Use the fixing screws to tighten the feet to the convector. You may need to make some physical effort for fastening to be secure.

5. Input the wheels to the supporting feet.

6. Double check the fastening. Turn the appliance over to correct position and set it on a flat, horizontal surface strictly upright.

Electric convector is ready to work!

1. Convector is designed for connection to the plug with single-phase voltage 220V~/50Hz.

2. Before connecting, make sure that the voltage is correct as specified on the nameplate with the technical data of the device.

3. When connecting the convector to the mains, the applicable electrical safety rules must be observed.

4. Electric outlet must be properly grounded. The socket must be rated for at least 10A. Electrical plug and socket must always be dry to prevent electrical leakage. Regularly check that the electrical plug is firmly connected to the outlet. Check the plug in the following order: insert the plug into the socket. After half an hour, turn off the convector and unplug the power cord, check if the plug is warm with the hand. If the plug is heated to a temperature above 50°C, in order to avoid damage, accidents, fire, due to poor electrical contact replace the socket with help of a specialist.

Connect the convector to the mains by inserting the plug of the power cord into a power outlet, and set the power mode switch to the position.

• Press the button to select low heating power, the indicator light of the button will be on during heating.
• Press the button to select medium heating power, the indicator light of the button will be on during heating.
• Press both and buttons to select high heating power, the indicator lights of the both and buttons will be on during heating.

Turn the thermostat knob fully clockwise. When the room temperature reaches the set level, turn the thermostat knob counterclockwise until the appliance turns off. Now the thermostat will maintain the set temperature, periodically turning the convector on and off.

Set the switch keys to the “O” position and disconnect the device from the mains.

The external body of the device must be regularly cleaned from dust and dirt, because this affects the efficiency of its work.

Before cleaning, turn off the device and unplug it from the network, let it cool, then wipe its body with a soft, slightly damp cloth. Then wipe it dry and allow the device to dry completely. It is not recommended to use detergents, including detergents with abrasive compounds to clean the body of the device. Do not damage the appliance with sharp objects, because scratches on paint can cause rust.

The rear side of the convector must also be periodically cleaned from dust and dirt. To do this, disconnect the device from the brackets, and after cleaning, put it back on the brackets.

Cleaning should be carried out periodically to maintain the technical condition of the convector and preserve its appearance for many years.

• No power: Check whether the power supply is disconnected from the device and, if necessary, connect device to power supply
• Temperature limiter parted electrical circuit and shut off the heating elements: Ensure that the air inlet or outlet grille is not blocked by foreign objects and wait for turning on of the temperature limiter, after the body of the device cools down.
• Malfunction in circuit breaker: Change the circuit breaker
• Defective power relay: Contact an authorized service center
• Defective thermostat: Contact an authorized service center
• Defective heating element: Contact an authorized service center
• Faulty temperature limiter: Contact an authorized service center to fix it

• Power cord is broken: Contact an authorized service center to fix it
• Low voltage in power network: Check power network
• Low heating temperature is set on thermostat: Set the temperature higher on thermostat
• Defective heating element: Contact an authorized service center