HUION KAMVAS 13 GS1331 (01) PDF Document

Before cleaning the display, unplug the USB cable and wipe it with a soft damp cloth. Do not use any kind of detergents.

Do not place the display near water sources such as a bathtub, washbasin, sinks, washing machine, damp basement, swimming pool, etc.

Do not place the display where it is unstable or at a height where children can easily reach it in order to avoid danger.

Do not place the display and digital pen close to the magnetic field.

The grooves and holes on the back case are designed for ventilation to prevent the monitor from overheating. Please do not place the display on beds, sofas, carpets or in embedded devices.

To protect your display, please switch off the power when it is not in use. During blackouts or not using for a long time, please unplug the display from the socket.

If the display has a breakdown, do not open the main case and try to repair it by yourself. Please ask for a service for proper repair and maintenance.

When the following situations occur, please unplug the power adapter and you may need a service for full repair and maintenance:

The power wire or plug is damaged or worn out.

There is liquid splashed inside of the display.

The display has fallen or the LCD is broken.

When obvious abnormalities occur to the display.

While getting the components replaced, you are supposed to guarantee that the repairman is using the substitute components specified by the manufacturer. Unauthorized component replacement might cause fire, electric shocks or other dangers.

Hold the pen as you hold a normal pen or pencil. Adjust your grip so that you can toggle the side switch easily with your thumb or forefinger. Be careful not to accidentally press the switch while drawing or positioning with the pen.

When not in use, place the pen in the pen case or on the desk. Do not place the pen on the surface of screen, which may interfere with the use of other screen cursor positioning equipment, it may also cause your computer unable to enter the sleep mode.

Move the pen slightly above the active area without touching the screen surface, the cursor will move to the new position accordingly.

Press the pen tip on the screen to make a selection. Tap the screen once with the pen tip, or touch it to the screen with enough pressure to register a click.

Use the pen tip to tap on the screen once to produce a click. Tap to highlight or select an item on the screen and double-click to open it.

Select the object, then slide the pen tip across the screen to move it.

The side buttons of the pen can be set to two different customizable functions. You can use the buttons whenever the pen tip is within 10mm of the display active area. You do not have to touch the pen tip to the display in order to use the switch.

The power button was placed on the left side of the digital screen, you need to turn on the power switch before using.

Press K4 & K5 for around three seconds until the OSD menu appears and meanwhile the indicator will flash green. The function of K2 K3 K6 K7 will become OSD function.

K2 AUTO: Before entering menu, its function is auto adjustment. After entering menu, its function is back to previous menu.

K3 MENU: Press to call up the menu, after entering menu, its function is confirm.

K7 – : After entering menu, its function is down/left/decrease.

K6 + : After entering menu, its function is up/right/increase.

Press K4 & K5 again for around three seconds until the OSD menu disappears, the function of K2 K3 K6 K7 will become shortcuts function again.

Device disconnected: The display hasn’t connected to your computer.

Device connected: The display has already connected to your computer.

If the secondary display is a mirrored mode connection, this display and another monitor will display exactly the same image and screen cursor movement.

If you are in the extended display mode, you need to set the display on the driver that which portion of the display screen your KAMVAS will map to.

Full Area: the entire active area of the Display. This is the default setting.

Same Ratio with LCD.

Customize Area: 1. Enter coordinate values. or 2. Drag the corners of the foreground graphic to select the screen area.

By changing the direction of the display to adapt to the left and right hand operation. We provide four directions of choice.

Place the cursor on the button or click the button icon to see the default values for the press keys.

Select the function to be achieved on the pop-up dialog box, then click APPLY or OK to take effect.

You can slide up and down to achieve zoom function.

Check/Uncheck “Enable Press key”.

Select the function to be achieved on the pop-up dialog box, then click APPLY or OK to take effect.

The pressure sensitivity will be changed by dragging the slider up and down, the smaller the value, the more sensitive the pressure.

You can gradually apply pressure to the stylus on the screen to test the pressure level. Click “Clear” button to clear all the ink.

Click the red point of the cross center appearing on the screen to complete the calibration.

Click “Restore Default” to restore to the factory settings.

Click “Cancel calibration” or press ESC on the keyboard to cancel the calibration.

Windows 7 or later, macOS 10.12 or later.

Possible cause: Power is not on or socket/power cable issue. Possible solution: Make sure power is on and check the socket and power cable.

1. Make sure power is on.

2. Correctly connect the 3-in-1 cable.

3. If you connect the display with a laptop, please make sure the display is on the right display mode: extend or duplicate mode.

4. Check whether the side indicator shows green, if not, it means no signal in. Please reboot your computer or reconnect the cable.

5. Is the signal wire broken or bent? If so, please replace the signal wire.

Please set the display resolution with 1920 x 1080.

Check the pins of the signal wire are not bent or fractured.

As the regional color temperature is different, so minor chromatic aberration is a normal phenomenon.

It is likely that there is electric equipment nearby that brings about electronic interference.

1. If the driver is damaged or is not properly installed, please uninstall the driver and reinstall it.

2. Try restarting your computer.

3. Try re-inserting the USB cable.

Try re-inserting the USB cable or restarting your computer.

When pressing the side button, please make sure that the nib didn’t touch the glass surface and the distance between the nib and surface is within 10mm.

Try calibration.

Windows 7 or later, macOS 10.12 or later.

The resolution is 1920 x 1080 (16:9).

The LCD Type is IPS LCD.

The Active Area is 293.76 x 165.24 mm.

The Contrast Ratio is 1000:1.

The Brightness is 220 cd/m².

The Response Time is 25 ms.

The View Angle is 89°/89°(H)/89°/89°(V) (Typ.)(CR > 10).

The Gamut is 120% sRGB.

The Display Color is 16.7 M(8bit).

The Touch Type is Passive Electromagnetic Resonance.

The Resolution is 5080 LPI.

The Pressure Level is 8192.

The Accuracy is ±0.5 mm(Center), ±3 mm (Corner).

The Sensing Height is 10 mm.

The Report Rate is 266 PPS.

The Pen Model is PW517.

The Pen Dimension is 163.7 x Φ14.3 mm.

The pen has Two Customized Press Keys.

The Output Voltage is 5V 2A.

The Video Interfaces are USB-C (3-in-1 Cable) & USB-C (USB 3.1).

There are 8 Customized Press Keys.

The Dimension is 366.5 x 217.4 x 11.8mm.

The Net Weight is 0.98 kg (without stand).

An Adjustable Stand is Two Levels Stand (Optional).

Connecting your Android phone and pen display with USB-C to USB-C USB 3.1 Gen1 cable and connecting the pen display and the power adapter or power bank with USB-C to USB-A cable.

Please make sure your smart android phone supports Dex or PC mode.

Before installing, you need to uninstall other driver of similar products, including the old driver of this product.

Before installing, please close all graphics software and anti-virus software to avoid unnecessary mistake.

After finishing installation, you can find the driver icon in the system tray area, which means the driver was installed successfully; when you connect the tablet to computer, the icon will change to color which means the driver has already recognized the tablet and you can start using it now.