HOLMES HTF3610AR (02) PDF MANUAL

1. To assemble the pedestal, simply snap the 2 pedestal halves together.
2. Pull the power cord through the assembled pedestal, making sure the wider end of the pedestal is facing towards the fan housing.
3. Align marking “A”, located at the bottom of the fan housing, with marking “A” on the top end of the pedestal. Insert the alignment post from the pedestal into the alignment hole on fan housing for proper alignment.
4. Use 4 screws (M4x10mm) provided to attach the assembled pedestal to the bottom of the fan housing. Secure the screws with a screwdriver.
5. Snap the 2 base halves together by sliding the posts of one base half into the slots of the second base half.
6. Pull the power cord through the center hole of the assembled base.
7. Align marking “B”, located at the center hole of the assembled base, with marking “B” at the bottom end of the pedestal. Insert the alignment post from the pedestal into the alignment hole on base for proper alignment.
8. Use 4 screws (M4x10mm) provided to attach the assembled base to the pedestal. Secure the screws with a screwdriver.
9. Wind the power cord underneath the base. Loosen the cord clip and place cord inside the clip. Secure the cord clip onto the base bottom with the 2 screws (M4x12mm) provided.
10. Turn fan right side up and place on a dry and level surface before operating.

A. Power/Speed Settings:

• Press /: On, I, II, III, Off

B. Timer Control:

• Press : Turns Off in 1, 2, 4, 8 hours

C. Oscillation Control:

• Press: Oscillation On, Off

D. Natural Breeze, Sleep Breeze Modes:

• Press / : Natural Breeze, Sleep Breeze
• Natural Breeze Mode: will cycle through the fan speed settings randomly.
• Sleep Breeze Mode: will cycle through the fan speed settings in order.

1. Remove battery cover from remote control.
2. Remove old batteries from the remote control.
3. Insert two new batteries, pressing them firmly into their slot.
4. Replace the battery cover.

NOTES:

• Replace all batteries of a set at the same time.
• Being careful not to bend or damage the contact spring, clean the battery contacts and devices’ contacts prior to installing the batteries.
• Remove the batteries from the equipment when it is not being used for an extended period of time.
• Remove the used batteries promptly.
• Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not discard used batteries into household trash containers. Contact your local government for disposal or recycling practices in your area.

• Always unplug the fan before cleaning.
• Clean the fan with a soft cloth moistened with a mild soap solution.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline, thinner, benzene.
• You may also clean the front grill of the fan by lightly running a vacuum cleaner nozzle over the grill surface.

User Servicing Instructions

1. Unplug your fan. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead screwdriver to slide the cover down towards the prongs. Ensure that fuse cover is completely open before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry the fuse out of the compartment by the metal ends of the fuse.
4. Place plug on a solid, flat surface. Insert new 5 Amp, 125 Volt fuse into fuse compartment and use a small screwdriver to secure the metal ends of the fuse into the compartment. Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is difficult to close, make sure fuse is secured in place completely by pressing down on metal ends of the fuse.
6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.