FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF USER GUIDE
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF USER MANUAL
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF OWNER GUIDE
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF OWNER MANUAL
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF REFERENCE GUIDE
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF REFERENCE MANUAL
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH HOBART MG2032 ML-134105 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD HOBART MG2032 ML-134105 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
HOBART MG2032 ML-134105 (01) PDF SUMMARY:
What is the size of the knife and plate that the MG1532 & MG2032 Mixer-Grinders are designed to use?
The MG1532 & MG2032 Mixer-Grinders are designed to use a #32(42/46) size knife and plate.
What is the smallest size of the hole that the plate should have?
Do not use a plate with a hole size smaller than 3/32".
What are the horsepower (HP) ratings for the Grind Motor and Mix Motor on the MG1532 & MG2032 Mixer-Grinders?
The MG1532 & MG2032 Mixer-Grinders are equipped with a 7 1/2 HP Grind Motor and a 1 HP Mix Motor.
What is the rotation speed of the worm and mix arm?
The worm rotates at 216 RPM and the mix arm rotates at 23 RPM.
How does the hopper guard (lid) open?
Releasing the latch handle allows the hopper guard (lid) to open easily — torsion springs counterbalance the lid’s weight.
What does the #46 Wedge cylinder do?
The exclusive Hobart designed #46 Wedge cylinder grinding end speeds product from hopper to grinding end by pulling pieces of meat through the large upper opening of the cylinder.
What are some of the options and/or accessories that can be ordered with the MG1532 & MG2032 Mixer-Grinders?
The MG1532 & MG2032 Mixer-Grinders may be ordered with a pneumatic foot switch accessory, and a hopper side-feed inlet (factory installed) for the right side of the MG2032 hopper only. An adapter ring for the first-cut grinder is also an available accessory.
How much fresh meat can the MG1532 hopper hold?
The MG1532 hopper can hold up to 150 pounds of fresh meat.
How much fresh meat can the MG2032 hopper hold?
The MG2032 hopper can hold up to 200 pounds of fresh meat.
What is the grinding rate for the MG1532 & MG2032 Mixer-Grinders when grinding fresh boneless beef?
The MG1532 & MG2032 Mixer-Grinders can grind at a rate of 55 to 60 pounds of fresh boneless beef per minute, first or second cut through a 1/8" plate.
What is the grinding rate for the MG1532 & MG2032 Mixer-Grinders when grinding pork?
Pork can be ground first cut through a 3/4" breaker plate and second cut through a 3/16" plate at 60 to 65 pounds per minute.
How much frozen meat can be ground per batch, and under what conditions?
Up to 60 pounds of frozen meat per batch can be ground from flake or stick form when tempered to 26°F or higher and the first grind is through a 3/8" or larger plate.
What is recommended for best results when using the mixer-grinder?
For best results, it is recommended to use the equipment in a cold room and/or using cold product. This will help reduce the fatting of meat at the grinder head and on the mixing arm and worm.
What steps should be taken if the mixer-grinder is found to be damaged after unpacking?
If the mixer-grinder is found to be damaged, the carrier must be notified within five business days of receipt, the carrier’s local terminal must be notified immediately, all original packing materials must be kept for inspection, the mixer-grinder cannot have been moved, installed, or modified, and Hobart customer care must be notified.
What should be done prior to installation of the mixer-grinder to check the electrical service?
Prior to installation, the electrical service should be tested to make sure it agrees with the specifications on the machine data plate.
How do you install casters or adjustable legs?
While the mixer-grinder is still attached to the skid, lift one end of the skid 2" high and place blocks underneath each runner to hold the skid at that height, mount two of the casters underneath the raised end of the mixer-grinder by bolting the casters from the bottom. Lower the skid. Repeat this process for the other end and then disassemble the skid.
How should you level the mixer-grinder?
Level the mixer-grinder, both front-to-back and side-to-side, by loosening the two set screws on the caster shaft and screwing the caster up or down. Tighten both set screws when level.
How do you install the pneumatic foot switch?
To install the pneumatic foot switch, insert the tube from the foot switch firmly into the fitting located under the front floor panel of the machine. To remove, press the fitting locking ring and gently pull the tube from the fitting.
How should electrical connections be made?
Electrical and grounding connections must comply with applicable portions of the national electrical code and/or other local electrical codes.
What should you do before working on the electrical circuit?
Disconnect the electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit.
What should be done to check motor rotation on three-phase machines?
With the grinder cylinder in place and the hopper lid closed, check the rotation by pushing the MIX-GRIND START switch and then pushing the STOP switch. The mixing arm and worm should both rotate counterclockwise when viewed from the machine’s front.
How do you correct motor rotation if it is incorrect?
Disconnect the electrical power supply and interchange any two of the incoming power supply leads. Reconnect the power supply and verify that both the worm and the mixer arm rotate counterclockwise.
What is the function of the control box heaters?
The mixer-grinder has a heater in the control box and another heater in the front control panel to keep the controls dry. They are automatically ON when the machine is electrically connected.
When should the mixer-grinder be connected to the power supply?
The mixer-grinder should always be connected EXCEPT when performing assembly, disassembly, cleaning, or maintenance of the machine.
What does the MIX START button do?
The MIX START button starts rotating the mix arm. Use the Stop Button to stop mixing.
What does the STOP button do?
The STOP button turns the mixer-grinder off. It also turns the Foot Switch off if it was on.
What does the MIX/GRIND START button do?
The MIX/GRIND START button starts rotating both the mix arm and worm. Use the Stop Button to stop mixing and grinding.
What does the FOOT SWITCH do?
When On, the Mix Start and Mix/Grind Start Buttons are inoperable and the accessory Foot Switch can be used to Mix/Grind ONLY. The indicator light shows when the Foot Switch is On. Push the STOP Button to turn the Foot Switch Off.
What does the hopper lid interlock switch do?
The interlock switch requires the hopper lid to be closed before the machine can operate. Raising the hopper lid opens the electrical circuit and makes the machine inoperative.
How should the grinder attachment be installed?
The Wedge cylinder is marked TOP and BOTTOM. Make sure TOP is visible.
How do you disassemble the grinder attachment for cleaning?
Use the spanner wrench to loosen the adjusting ring and remove the adjusting ring, plate and knife. Then loosen, but do not remove the grinder attachment’s two flange nuts, using the spanner wrench. Rotate the cylinder clockwise and remove the cylinder; then, remove the worm.
How do you reassemble the grinder attachment?
Install the worm and then the cylinder. Make sure TOP is visible on the cylinder and that the cylinder’s flange nuts are tight before assembling the knife, plate, and adjusting ring. Use only the flange nuts provided.
How is the rubber seal at the drive end of the worm removed and reinstalled?
The rubber seal at the drive end of the worm can be removed by hand for cleaning. Grasp the outer flange of the seal or use a dull screwdriver to pry the seal loose. Reinstall seal before installing worm.
What preliminary lubrication is needed for the knife and plate?
Rub tallow or food grade mineral oil over the cutting faces of these parts.
When assembling the knife, which side should face the plate?
When assembling the knife, be sure to turn the cutting side towards the perforated plate.
How should the plate be aligned in the cylinder?
The notch on the circumference of the plate must fit over the pin in the cylinder.
How do you remove the mixing arm?
Loosen the bushing retainer’s two flange nuts and remove the bushing retainer. Raise the hopper lid and pull the mixing arm from the square drive end, lifting the mixing arm from the hopper.
How do you reassemble the mixing arm?
When reassembling, make sure TOP on the bushing retainer is “up” so the mixing arm runs straight between the round bushing and the square drive-end. Reassemble the mixing arm before assembly of the grinder cylinder and worm.
What is the hopper capacity for the MG1532 and MG2032?
The MG1532 has a hopper capacity of up to 150 pounds of fresh meat, and the MG2032 has a hopper capacity of up to 200 pounds of fresh meat depending on the type of product.
What is the difference between the MIX and MIX-GRIND operations?
During the MIX operation, the mixing arm rotates and the grinder worm does not. Continuous self-feeding occurs along with grinding in the MIX-GRIND operation.
Is mixing of uncut or unground meat recommended?
Mixing of uncut or unground meat is not recommended.
What is the procedure for first grind?
Fill the hopper and close and latch the hopper lid. Push the MIX-GRIND button to start grinding. Press the STOP button to stop grinding.
What is the procedure for second grind?
Fill the hopper and close and latch the hopper lid. Press the MIX button. After desired mixing, press the STOP button. Then, press the MIX-GRIND button to start grinding; press the STOP button to stop grinding; or activate and use the optional accessory Foot Switch.
What should be done before cleaning or servicing the machine?
Disconnect the electrical power supply before cleaning or servicing this machine.
What should you do after disconnecting the electrical power supply during cleaning?
Seal the receptacle to prevent entrance of moisture. To make this seal on Hobart supplied receptacles and pendant connectors, place the cover cap into position and turn the screw type sealing ring clockwise.
What components should be removed when cleaning the mixer-grinder?
Remove the mixing arm, grinder adjusting ring, knife and plate. Remove the cylinder before removing the worm. The mixing arm seal and the worm seal should be removed by hand for cleaning.
How should the mixing arm seal and the worm seal be removed and reinstalled?
The mixing arm seal and the worm seal should be removed by hand for cleaning. Grasp the outer flange or use a dull screwdriver to pry the seal loose. Align tab at bottom of each seal with notch at bottom of applicable seal hole in end wall of hopper. Arrow at top of seal points up. Squeeze sides of seal and push in. Push in top of seal. Make sure seals are properly seated.
What should be installed under the hopper during cleaning?
Install the drain tray under the hopper to direct wash water into a catch bucket or into a floor drain.
How should the machine be washed and dried?
The machine can be washed down with hot water or steam. When using detergents and sanitizers, follow the manufacturer’s instructions. Rinse with clear water and allow to air dry.
What should be applied to the seals after cleaning?
After cleaning the machine, apply food grade mineral oil to lubricate the inside rim of the mixing arm seals and the worm seal where the mixing arm and worm will touch the seals.
What should be applied to the grinder parts after cleaning?
After cleaning, a light coat of food grade mineral oil is recommended for the cylinder, adjusting ring, knife, plate, and worm — before reassembly.
Are the motor bearings lubricated?
Both motor bearings are pre-lubricated and sealed. No further lubrication is required.
How should the gear cases for the mixing arm and worm be lubricated?
Contact Hobart Service for lubrication maintenance annually, or when needed.
CLICK HERE TO DOWNLOAD HOBART MG2032 ML-134105 (01) PDF MANUAL