HAVIS KB-104 (01) PDF MANUAL

HAVIS KB-104 (01) PDF SUMMARY:

What should I never do when stowing or mounting the rugged keyboard in a vehicle?

NEVER STOW OR MOUNT THE RUGGED KEYBOARD DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.

---

Should I use the rugged keyboard while driving?

DO NOT USE RUGGED KEYBOARD WHILE DRIVING.

---

What power options are recommended for the connected computer?

It is RECOMMENDED TO SET THE CONNECTED COMPUTER’S POWER OPTIONS TO “NEVER” SLEEP.

---

What BIOS settings are recommended for the connected computer?

It is RECOMMENDED TO SET THE CONNECTED COMPUTER’S BIOS TO “ENABLE USB WAKE SUPPORT”.

---

How do I enable USB wake support in the BIOS?

1. Push ‘F2’ key during the computer’s boot sequence.
2. Select SETTINGS.
3. Select POWER MANAGEMENT.
4. Select USB WAKE SUPPORT.
5. Check the box for ENABLE USB WAKE SUPPORT.
6. Left Click: APPLY.
7. Left Click: EXIT.

---

What should I do before beginning the installation?

READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.

---

What should I avoid placing on top of the rugged keyboard?

Do not place metal objects or containers of liquid on top of the Rugged Keyboard.

---

What temperature environment should I avoid leaving the rugged keyboard in?

Do not leave the Rugged Keyboard in a high temperature environment (greater than 85°C, 185°F) for a long period of time.

---

How do I install the rugged keyboard if I’m not using the Havis Keyboard Mount?

1. Determine if your mounting location is equipped with VESA 75 or AMPS mounting pattern.
2. Install the Rugged Keyboard to your mounting device using (4) M4 x 0.7mm screws (Hardware Kit Item #1).
   • NOTE: Length of screw is dependent upon your specific mounting application.
   • Torque screws to 20 in-lbs (2.3Nm) ± 10%.

---

How do I connect the rugged keyboard to a computer?

Insert the USB connector into a compatible USB port on the computer or docking station. The computer will detect and install drivers once the keyboard initiates. Drivers are standard plug and play.

---

How do I adjust the backlight?

Cycle keyboard illumination intensity levels between OFF and maximum brightness using the Backlight Adjustment Button.

---

What does the ‘Emergency’ button do?

The ‘Emergency’ Button sends a ‘SHIFT’ + ‘F1’ key sequence to the connected computer.

---

What does it mean when both USB caution lights are illuminated?

Both USB Caution lights will illuminate when either of the following occurs:

• There is an error with the connected USB device
• The connected USB device is drawing current above 500mA

---

Will the Fingerprint Reader work without software?

Your computer or tablet must have fingerprint reader software pre-installed. The Fingerprint Reader will not operate without software capable of reading your fingerprint.

---

How do I initially register my fingerprint?

Follow your device software’s instructions for initial registration of your fingerprint and for general operation details.

---

How do I scan my fingerprint?

1. Begin with your chosen fingerprint positioned above the Fingerprint Reader (close to or hovering above the home button).
   • To get a complete scan of your fingerprint, start the scan with the base of the fingerprint above the reader and close to the home button to allow more of the print to be successfully scanned.
2. Press your finger down onto the keyboard surface.
   • It is okay to press down on the home key while attempting the swipe. You want the Fingerprint Reader to get a complete scan of your entire fingerprint.
3. With your finger pressed onto the keyboard surface, swipe from top to bottom across the reader. Try to keep the finger flat to get a better scan of the fingerprint.

---

How should I clean the Havis Rugged Keyboard?

The Havis Rugged Keyboard can be cleaned with a soft cloth.

---

What should I use to clean the Havis Rugged Keyboard?

USE A SOFT CLOTH OR SPONGE TO CLEAN.

---

What should I avoid using when cleaning the Havis Rugged Keyboard?

• DO NOT USE A STIFF BRUSH. NO INTENSE SCRUBBING.
• DO NOT USE CORROSIVE CLEANING SOLVENTS.

---

What should I do if the Fingerprint Reader becomes dirty or cloudy?

If the Fingerprint Reader becomes dirty or cloudy, wipe gently with a soft, lint-free cloth. Do not use water or corrosive cleaning solvents.

---

What can cause poor fingerprint scans?

Certain skin conditions and environmental conditions can cause poor fingerprint scans. Damp, extremely dry, and/or scarred skin can impact scanning operations.

---

What should I do if my finger is damp or wet before using the fingerprint reader?

If your finger is damp or wet, dry it before use.

---

What should I do if my finger is extremely dry before using the fingerprint reader?

If your finger is extremely dry, you can use a moisturizing lotion before use.

---

What is the recommendation in case I cut or injure my finger?

It is best to register more than one fingerprint, or keep a back-up password or pin in case you cut or injure your finger.