HAIFUAN S200TM (01) PDF DOCUMENT

FREE ENGLISH HAIFUAN S200TM (01) PDF DOCUMENT.
FREE ENGLISH HAIFUAN S200TM (01) PDF USER GUIDE.
FREE ENGLISH HAIFUAN S200TM (01) PDF USER MANUAL.
FREE ENGLISH HAIFUAN S200TM (01) PDF OWNER GUIDE.
FREE ENGLISH HAIFUAN S200TM (01) PDF OWNER MANUAL.
FREE ENGLISH HAIFUAN S200TM (01) PDF REFERENCE GUIDE.
FREE ENGLISH HAIFUAN S200TM (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH HAIFUAN S200TM (01) PDF REFERENCE MANUAL.
FREE ENGLISH HAIFUAN S200TM (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH HAIFUAN S200TM (01) PDF OPERATING INSTRUCTIONS.

CLICK HERE TO DOWNLOAD HAIFUAN S200TM (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

NO IMAGE CONTENT AT THIS TIME. PLEASE CHECK BACK LATER

What are the product specifications for the HAIFUAN S200TM?

Item No.	S200MF / S200TM
Dimension	155X68*78MM / 6.1 X 2.72 X 3.07″
Material	Zinc Alloy
Weight	2.3 kgs / 5 pounds

The standard single latch backset is adjustable between 60mm (2-3/8″) and 70mm (2-3/4″).

What are the technical specifications of the HAIFUAN S200TM lock?

Card type	Mifare-1 Card(S200MF) / TM Card(S200TM)
Card inductive distance	3cm / 1.18″
Unlock method	Card, Code, Code + Card, Mechanical key
Code length	4-8 digits
User capacity	200 users
Power supply	4pcs AA batteries
Static current	≤30uA
Working current	≤200mA
Suitable Door Thickness	38-50mm / 1.5″-1.97″
Backup power terminal	9V(at the bottom of front plate)
Handle Orientation	Reversible
Initial Master code	123456
Initial Debug code	0 (After installed, press “0”,then”#” to open door directly, automatically become invalid after changing master code)

How do I drill holes for the HAIFUAN S200TM installation?

1. Measure up approximately 36″ from the door bottom. Apply the template to the door edge. Mark the center of the door edge as indicated on the template.

2. Mark the center hole on the door face through the guide on the template for a 2-3/8″ (60mm) or 2-3/4″ (70mm) backset.

3. Drill a 2-1/8″ hole through the door face as marked for the lockset. It is recommended that holes be drilled from both sides to prevent splitting.

4. Drill a 31/32″ or 1″ hole in the center of the door edge for the latch. Check the template for the correct size for your latch application.

How do I install the latch and strike plate for the HAIFUAN S200TM?

1. Insert the latch in the hole, keeping it parallel to the face of the door. Mark the outline and remove the latch.

2. Chisel 1/8″ deep or until the latch face is flush with the door edge.

3. Insert the latch with the beveled edge of the latch facing the door frame and tighten the screws.

4. Install the strike plate on the door jamb accordingly.

How do I prepare and install the front plate of the HAIFUAN S200TM?

Prepare to Install Front Plate

1. Fix three connecting screw tubes on the front plate.

2. Fix the spindle with a secure pin to the front plate.

Install Front Plate

1. Place the waterproof rubber under the front plate.

2. Install the front plate to the door, and pull the data line through the door hole.

How do I install the back plate and outer plate of the HAIFUAN S200TM?

Install Back Plate

1. Place the waterproof rubber under the inner back plate.

2. Install the inner back plate to the door. Fix it with three screws.

3. Connect the data line to the inner plate.

4. Install 4 AA alkaline batteries.

5. Install the outer plate with two screws.

6. Test the lock and make adjustments if necessary.

How do I reset the Master Code on my HAIFUAN S200TM?

Operating steps	Locks status
Use a screwdriver to move away the back panel. You will see a button beneath the battery case.	none
Remove one battery, press the reset button for 5 seconds.	none
Put the battery back, press the reset button for 10 seconds until the front panel indicator light flashes blue.	You will hear two beeps, and the light will change to blue. The master code is now reset to 123456.

Note: If you have just received this lock and have not set any code, you can skip this step. This operation will clear all previously added users.

How do I modify the Master Code on my HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front panel indicator light will flash blue, and the keypad will illuminate.
2	Input the initial master code: “123456”, then press “#”.	You will hear two beeps.
3	Input “11” then “#” within 10 seconds (before the indicator light extinguishes).	You will hear two beeps.
4	Input “New Master Code” (4-8 digits) then “#”.	You will hear two beeps.
5	Input “New Master Code” again, then “#”.	You will hear 4 beeps, the indicator light extinguishes. The new Master Code is set successfully.

Note: If there is no reaction after you press the “#” and the keypad does not illuminate, take out all the batteries, press the reset button for 5 seconds, and then put the batteries back and follow the instructions again.

How do I add a normal code user to the HAIFUAN S200TM?

You can set up 200 users in total, including Code User, Card User, and Code & Card combination User. Before adding a user, you must set a user group number. User group numbers consist of 3 digits, from 001 to 200, and each number can only be used once. For example, to set up 2 code users and 2 card users, you need 4 groups, such as 001, 002, 003, 004.

Step	Operating steps	Locks Status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “01” then “#” within 10 seconds (before the indicator light extinguishes).	You will hear two beeps.
4	Input “user group number” such as “001” within 10 seconds. Then press “#”. (Group numbers can only be used once. For the next user, use another group like “002”, “003”, etc.).	You will hear two beeps.
5	Input “Code” then “#” within 10 seconds (before the indicator light extinguishes).	You will hear two beeps.
6	Press “#” 2 times.	First “#” will “beep” twice. Second “#” will “beep” 3 times. The code is added successfully.
7	After 15 seconds, or press “#”, Exit.	Long time of “beeps”, indicator light extinguish.

How do I open the door using a code with the HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Input “Code” then “#”.	You will hear one beep, and the indicator light will keep blue. You can also hear the sound of the lock motor. Turn the handle to open the door.
2	After 5 seconds.	You will hear two beeps, the red light flashes twice, the lock returns to locked status, and the indicator light extinguishes.

How do I add a card user to the HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input “Master Code” then “#”.	You will hear two beeps.
3	Input “01” then “#” within 10 seconds (before the indicator light extinguishes).	You will hear two beeps.
4	Input “group number” such as “002” within 10 seconds then “#”. (Group numbers can only be used once, if you already used 002, then input 003 or another valid number).	You will hear two beeps.
5	Put the “Card” close to the card read area within 10 seconds, then press “#”. For S200TM, the card read area is the metal circle above the number keys.	You will hear two beeps.
6	Press “#” 2 times.	First “#” will “beep” twice. Second “#” will “beep” 3 times. Card added successfully.
7	After 15 seconds, or press “#”, Exit.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I open the door using a card with the HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Get the Card close to the card read area.	You will hear one beep, and the indicator light keeps in blue. You can also hear the sound of the lock motor. Turn the handle to open the door.
2	After 5 seconds.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I add a combination code and card user to the HAIFUAN S200TM?

Note: You must set the code first, and then the card.

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “01” then “#” within 10 seconds.	You will hear two beeps.
4	Input “group number” such as “003” within 10 seconds then “#”. (Group numbers can only be used once).	You will hear two beeps.
5	Input “Code” within 10 seconds then “#”.	You will hear two beeps.
6	Put the “Card” close to the inductive place within 10 seconds then “#”.	You will hear two beeps.
7	Press “#” 2 times.	First “#” “beep” twice. Second “#” “beep” 3 times. Card and code combination user added successfully.
8	After 15 seconds, or press “#”, Exit.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I open the door using a card and code combination with the HAIFUAN S200TM?

Under this mode, you need to use the Card together with the Code to open the door.

Step	Operating steps	Locks status
1	Get the “Card” close to the inductive place.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input the “Code” then “#”.	You will hear one beep, and the indicator light keeps in blue. You can also hear the sound of the lock motor. Turn the handle to open the door.
3	After 5 seconds.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I block a normal user on the HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “02” within 10 seconds then “#”.	You will hear two beeps.
4	Input “Group No.” of the user you want to block within 10 seconds then “#”. You can also input another group no. and press # to block it at the same time.	You will hear two beeps. Block up successful.
5	After 15 seconds, or press “#”, Exit.	Long time of “beeps”, indicator light extinguishes.

How do I re-start (unblock) a normal user on the HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “03” then “#” within 10 seconds.	You will hear two beeps.
4	Input “Group No.” which you want to re-start within 10 seconds then “#”. You can also input another group no. and then press # to unblock it at the same time.	You will hear two beeps. User re-start successful.
5	After 15 seconds, or press “#”, Exit.	Long time of “beeps”, indicator light extinguishes.

How do I delete a normal user from the HAIFUAN S200TM?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “44” within 10 seconds then “#”.	You will hear two beeps.
4	Input “Group No.” which you want to Delete within 10 seconds then “#”. You can also input another group no. and then press # to delete it at the same time.	You will hear two beeps. User Delete successful.
5	After 15 seconds, or press “#”, Exit.	Long time of “beeps”, indicator light extinguishes.

How do I add a one-time use code to the HAIFUAN S200TM?

The code can only be used once and automatically becomes invalid after use.

Step	Operating steps	Locks presentation
1	Press “#” to start the lock.	You will hear two beeps, front light flashes blue, and keypad illuminates.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “33” within 10 seconds then “#”.	You will hear two beeps.
4	Input “Group Number” within 10 seconds (e.g., “005”) then “#”. (Group numbers can only be used once. If you already used 005, input 006 or another valid number).	You will hear two beeps.
5	Input “One Time Use Code” (4-8 digits) within 10 seconds then “#”.	You will hear two beeps.
6	Press “#” 2 times.	First “#” will “beep” twice, second “#” will “beep” 3 times. Single use code added successfully.
7	After 15 seconds, or press “#”, Exit.	Long time of “beeps”, indicator light extinguishes.

How can I enter my code discreetly on the HAIFUAN S200TM if people are around?

If there are some people around you while operating the lock and you don’t want them to know your code, you can input some random digits before your actual code to confuse them. For example, if your code is “123456”, you could input “5465445”+“123456” to open the lock.

What happens if I enter the wrong code multiple times on the HAIFUAN S200TM?

The lock will be blocked for 5 minutes if you continue to input 3 wrong codes.

What are the function codes for programming the HAIFUAN S200TM?

	Code No.	Function
1	11	Modify Master Code
2	01	Add Normal User
3	02	Block up Normal User
4	03	Re-start Normal User
5	33	Add A Single Use Code
6	44	Delete Normal User

What should I do if I’m having trouble programming my HAIFUAN S200TM?

You can try the following steps:

1. First of all, please check if the batteries are installed in the correct way. The negative side of the battery should be connected to the spring part in the battery case. Please note that the master code can only be used to program other codes and cards; it cannot be used to open the lock.

2. Next, initialize the lock. To do this, take one battery out, press the reset button for 5 seconds, then put all the batteries back. Press the reset button for 10 seconds. The indicator light will flash blue twice and you will hear two beeps if successful.

3. If the reset is successful, you will be able to input “0” “#” to open the lock. If this works, all other functions should be fine. This is a key step.

4. After a successful reset, you can try to program the lock by inputting the following sequences:

First code set up: # → 123456 → # → 01 → # → 001 → # → your code → # → # → #

Second code set up: # → 123456 → # → 01 → # → 002 → # → your code → # → # → #

First card set up: # → 123456 → # → 01 → # → 003 → # → put one card close to inductive place → # → # → #

Second card set up: # → 123456 → # → 01 → # → 004 → # → put another card close to inductive place → # → # → #