HAIFUAN S200MF (01) PDF DOCUMENT

FREE ENGLISH HAIFUAN S200MF (01) PDF DOCUMENT.
FREE ENGLISH HAIFUAN S200MF (01) PDF USER GUIDE.
FREE ENGLISH HAIFUAN S200MF (01) PDF USER MANUAL.
FREE ENGLISH HAIFUAN S200MF (01) PDF OWNER GUIDE.
FREE ENGLISH HAIFUAN S200MF (01) PDF OWNER MANUAL.
FREE ENGLISH HAIFUAN S200MF (01) PDF REFERENCE GUIDE.
FREE ENGLISH HAIFUAN S200MF (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH HAIFUAN S200MF (01) PDF REFERENCE MANUAL.
FREE ENGLISH HAIFUAN S200MF (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH HAIFUAN S200MF (01) PDF OPERATING INSTRUCTIONS.

CLICK HERE TO DOWNLOAD HAIFUAN S200MF (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

NO IMAGE CONTENT AT THIS TIME. PLEASE CHECK BACK LATER

What are the technical specifications of the HAIFUAN S200MF lock?

Item No.	S200MF / S200TM
Dimension	155X68*78MM / 6.1 X 2.72 X 3.07″
Material	Zinc Alloy
Weight	2.3 kgs / 5 pounds
Card type	Mifare-1 Card(S200MF) / TM Card(S200TM)
Card inductive distance	3cm / 1.18″
Unlock method	Card, Code, Code + Card, Mechanical key
Code length	4-8 digits
User capacity	200 users
Power supply	4pcs AA batteries
Static current	≤30uA
Working current	≤200mA
Suitable Door Thickness	38-50mm / 1.5″-1.97″
Backup power terminal	9V(at the bottom of front plate)
Handle Orientation	Reversible
Initial Master code	123456
Initial Debug code	0(After installed, press “0”,then”#” to open door directly, automatically become invalid after changing master code)

Standard Single Latch: The backset is adjustable between 60mm (2-3/8″) and 70mm (2-3/4″).

How do I prepare the door and drill holes for the HAIFUAN S200MF lock?

1. Measure up approximately 36″ from the door bottom. Apply the template to the door edge. Mark the center of the door edge as indicated on the template.

2. Mark the center hole on the door face through the guide on the template for a 2-3/8″ (60mm) or 2-3/4″ (70mm) backset.

3. Drill a 2-1/8″ hole through the door face as marked for the lockset. It is recommended that holes be drilled from both sides to prevent splitting.

4. Drill a 31/32″ or 1″ hole in the center of the door edge for the latch. Check the template for the correct size for your latch application.

How do I install the latch and strike plate for the HAIFUAN S200MF?

1. Insert the latch in the hole, keeping it parallel to the face of the door. Mark the outline and remove the latch.

2. Chisel 1/8″ deep or until the latch face is flush with the door edge.

3. Insert the latch with the beveled edge of the latch facing the door frame and tighten the screws.

4. Install the strike plate on the door jamb accordingly.

How do I install the front plate of the HAIFUAN S200MF?

Prepare the Front Plate:

1. Fix three connecting screw tubes on the front plate.

2. Fix the spindle with a secure pin to the front plate.

Install the Front Plate:

1. Place the waterproof rubber under the front plate.

2. Install the front plate to the door, pulling the data line through the door hole.

How do I install the back plate of the HAIFUAN S200MF?

1. Place the waterproof rubber under the inner back plate.

2. Install the inner back plate to the door. Fix it with three screws.

3. Connect the data line to the inner plate.

4. Install 4 AA alkaline batteries.

5. Install the outer plate with two screws.

6. Test the lock and make adjustments if necessary.

How do I reset the Master Code on my HAIFUAN S200MF lock?

Note: This operation will clear all users added before. If you just got the lock and haven’t set any code, skip this step.

Operating steps	Locks status
Use a screwdriver to move away the back panel. You will see a button beneath the battery case.	none
Remove one battery, press the reset button for 5 seconds.	none
Put the battery back, press the reset button for 10 seconds until the front panel indicator light flashes blue.	You will hear two beeps, and the light will change to blue. The master code is now reset to 123456.

How do I modify the Master Code on the HAIFUAN S200MF?

The Master Code can be 4-8 digits long.

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front panel indicator light will flash blue, and the keypad will illuminate.
2	Input the initial master code: “123456”, then press “#”.	You will hear two beeps.
3	Input “11” then “#” within 10 seconds (before the indicator light extinguishes).	You will hear two beeps.
4	Input “New Master Code” (4-8 digits) then “#”.	You will hear two beeps.
5	Input “New Master Code” again, then “#”.	You will hear 4 beeps, the indicator light extinguishes, and the New Master Code is set successfully.

Note: If there is no reaction after you press the “#” and the keypad does not illuminate, take out all the batteries, press the reset button for 5 seconds, then put the batteries back and follow the instructions again.

How do I add a new Code User to the HAIFUAN S200MF lock?

You can set up to 200 users in total. Before adding a user, you must assign them a user group number from 001 to 200. Each number can only be used once.

Step	Operating steps	Locks Status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “01” then “#” within 10 seconds (before the indicator light extinguishes).	You will hear two beeps.
4	Input “user group number” such as “001” within 10 seconds, then “#”. (Group number can only be used once. For the next user, use “002”, “003”, etc.).	You will hear two beeps.
5	Input “Code” then “#” within 10 seconds.	You will hear two beeps.
6	Press “#” 2 times.	First “#” will “beep” twice. Second “#” will “beep” 3 times. Code added successfully.
7	After 15 seconds, or press “#”, Exit.	A long beep sounds, and the indicator light extinguishes.

How do I open the HAIFUAN S200MF door using a code?

Step	Operating steps	Locks status
1	Input “Code” then “#”.	You will hear one beep, and the indicator light keeps in blue. You can also hear the sound of the lock motor. Turn the handle to open the door.
2	After 5 seconds.	You will hear two beeps, the red light flashes twice, the lock returns to locked status, and the indicator light extinguishes.

How do I add a new Card User to the HAIFUAN S200MF lock?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input “Master Code” then “#”.	You will hear two beeps.
3	Input “01” then “#” within 10 seconds.	You will hear two beeps.
4	Input “group number” such as “002” within 10 seconds, then “#”. (Group number can only be used once).	You will hear two beeps.
5	Put the “Card” close to the card read area within 10 seconds, then “#”. (For S200TM, the area is above the number keys; for S200MF, it is the number key area).	You will hear two beeps.
6	Press “#” 2 times.	First “#” will “beep” twice. Second “#” will “beep” 3 times. Card added successfully.
7	After 15 seconds, or press “#”, Exit.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I open the HAIFUAN S200MF door using a card?

Step	Operating steps	Locks status
1	Get the Card close to the card read area.	You will hear one beep, and the indicator light keeps in blue. You can also hear the sound of the lock motor. Turn the handle to open the door.
2	After 5 seconds.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I add a new Code and Card Combination User to the HAIFUAN S200MF?

Note: You must set the code first, and then the card.

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “01” then “#” within 10 seconds.	You will hear two beeps.
4	Input “group number” such as “003” within 10 seconds, then “#”. (Group number can only be used once).	You will hear two beeps.
5	Input “Code” within 10 seconds, then “#”.	You will hear two beeps.
6	Put the “Card” close to the inductive place within 10 seconds, then “#”.	You will hear two beeps.
7	Press “#” 2 times.	First “#” “beep” twice. Second “#” “beep” 3 times. Card and code combination user added successfully.
8	After 15 seconds, or press “#”, Exit.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How do I open the HAIFUAN S200MF door using a Code and Card combination?

Step	Operating steps	Locks status
1	Get the “Card” close to the inductive place.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Code” then “#”.	You will hear one beep, and the indicator light keeps in blue. You can also hear the sound of the lock motor. Turn the handle to open the door.
3	After 5 seconds.	“beep” twice, red light flashes twice, back to locked status, and the indicator light extinguishes.

How can I block a normal user on the HAIFUAN S200MF?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “02” within 10 seconds, then “#”.	You will hear two beeps.
4	Input “Group No.” of the user you want to block within 10 seconds, then “#”. You can also input another group no. and press # to block it at the same time.	You will hear two beeps. Block up successful.
5	After 15 seconds, or press “#”, Exit.	Long beep, indicator light extinguishes.

How can I re-start (unblock) a normal user on the HAIFUAN S200MF?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “03” then “#” within 10 seconds.	You will hear two beeps.
4	Input “Group No.” of the user you want to re-start within 10 seconds, then “#”. You can also input another group no. and press # to unblock it at the same time.	You will hear two beeps. User re-start successful.
5	After 15 seconds, or press “#”, Exit.	Long beep, indicator light extinguishes.

How do I delete a normal user from the HAIFUAN S200MF lock?

Step	Operating steps	Locks status
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “44” within 10 seconds, then “#”.	You will hear two beeps.
4	Input “Group No.” of the user you want to delete within 10 seconds, then “#”. You can also input another group no. and press # to delete it at the same time.	You will hear two beeps. User Delete successful.
5	After 15 seconds, or press “#”, Exit.	Long beep, indicator light extinguishes.

How do I add a One-Time Use Code to the HAIFUAN S200MF?

This code can only be used once and becomes invalid automatically after use.

Step	Operating steps	Locks presentation
1	Press “#” to start the lock.	You will hear two beeps, the front light will flash blue, and the keypad will illuminate.
2	Input the “Master Code” then “#”.	You will hear two beeps.
3	Input “33” within 10 seconds, then “#”.	You will hear two beeps.
4	Input “Group Number” such as “005” within 10 seconds, then “#”. (Group number can only be used once).	You will hear two beeps.
5	Input “One Time Use Code” (4-8 digits) within 10 seconds, then “#”.	You will hear two beeps.
6	Press “#” 2 times.	First “#” “beep” twice, second “#” “beep” 3 times. Single use code added successfully.
7	After 15 seconds, or press “#”, Exit.	Long beep, indicator light extinguishes.

Is there a way to enter my code discreetly on the HAIFUAN S200MF if people are watching?

Yes. If there are people around you while operating the HAIFUAN S200MF lock and you don’t want them to know your code, you can input some random digits before your code to confuse them. For example, if your code is “123456”, you can input “5465445” + “123456” to open the lock.

What happens if I enter the wrong code multiple times on the HAIFUAN S200MF?

The HAIFUAN S200MF lock will be blocked for 5 minutes if you continue to input 3 wrong codes.

What are the function codes for programming the HAIFUAN S200MF?

	Code No.	Function
1	11	Modify Master Code
2	01	Add Normal User
3	02	Block up Normal User
4	03	Re-start Normal User
5	33	Add A Single Use Code
6	44	Delete Normal User

What are the troubleshooting steps if I am having trouble programming my HAIFUAN S200MF lock?

If you failed to program your HAIFUAN S200MF lock, you can try the following steps:

1. Check Batteries: First, check if the batteries are installed correctly. The negative side of the battery should be connected to the spring part in the battery case.

2. Master Code Use: Please note that the master code can only be used to program other codes and cards; it cannot be used to open the lock itself.

3. Initialize the Lock (Reset):

– Take one battery out.

– Press the reset button for 5 seconds.

– Put all the batteries back.

– Press the reset button for 10 seconds.

– If the reset is successful, the indicator light will flash blue twice and you will hear two beeps.

4. Test after Reset: If the reset was successful, you should be able to input “0” then “#” to open the lock. If this works, all other functions should be fine. This is a key step.

5. Programming Examples after Reset: After a successful reset, you can try these input sequences for programming:

– First Code Set Up: # → 123456 → # → 01 → # → 001 → # → your code → # → # → #

– Second Code Set Up: # → 123456 → # → 01 → # → 002 → # → your code → # → # → #

– First Card Set Up: # → 123456 → # → 01 → # → 003 → # → put one card close to inductive place → # → # → #

– Second Card Set Up: # → 123456 → # → 01 → # → 004 → # → put another card close to inductive place → # → # → #